Search Documents

By Wilbert J. Huff

This is the sixth of a series of annual reports describing the work of the? Explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with the activities of the division from July 1, 1940, to June 30, 1941. The studies outlined in this and preceding reports of the series have been conducted under the direction of the author and the respective unit leaders, to whom specific credit is given.

Jan 1, 1942

By David Oyler, Craig Compton

The The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Research Laboratory (PRL) is continuing to investigate the behavior of fully grouted roof bolts in the weak roof rock of the Safety Research Coal Mine (SRCM). This paper describes the results of three studies: • A series of 24 pull tests of bolts installed fully grouted and overcored to leave 12 inches of grouted bolt. The tests compared the pull-out performance of offset-head roof bolts with that of standard 5/8-inch bolts; • A second series of 24 tests that compared the pull-out loads obtained by bolts installed with 1 ft of resin (a Short Encapsulation Pull Test or SEPT) to that of fully grouted bolts overcored to leave only 12 inches of grouted bolt, and; • An investigation into the pressures generated during the installation of fully grouted resin bolts. All of the bolts installed and pulled were overcored and removed from the roof after the pull tests to allow inspection of the resin. The first study found that there was no significant difference in pullout load between the offset-head bolts and the standard bolts. The second study, comparing the SEPT bolts and the partially-overcored fully grouted bolts, indicated that SEPT can significantly underestimate bolt anchorage grip factor, suggesting that the SEPT is a conservative measure of actual bolt performance. Significant loss of resin to cracks in the roof was observed in the bolts overcored in the SRCM. The third study explored one possible explanation for the resin loss, high pressures generated during bolt installation. These tests employed bolts installed in strain gauged steel tubes. The results confirmed that significant pressures (greater than 4,000 psi) can be generated during bolt installation. The results of the pressure tests, combined with the observations of resin loss in bolts installed in the SRCM, suggest that under some circumstances resin loss and under-encapsulation could take place and lead to degraded bolt performance. Glove fingering was observed in all recovered bolts to various degrees. The limited comparative data suggested that the effect of glove fingering ranged from slight to moderate. Complete mixing of the resin was observed on all of the 40 bolts recovered (28 fully grouted and 12 SEPT). Australian and U.S. resins were compared and the Australian resins were observed to have much smaller catalyst compartment areas and lower resin viscosities. These differences are suggested as potential explanations for occasional resin mixing problems noted in Australian resin bolt installations.

By W. H. Tomlinson

The fourteenth National First-Aid and Mine Rescue Contest we;; held at the State fairgrounds, Columbus, Ohio, October 2, 3, and 4, 1951. The meet, the first such event in 21 years, was under the auspices of the Bureau of Mines, United States Department of the Interior, and the Joseph A Holmes Safety Association and was sponsored by the National Coal Association, the United Mine Workers of America, and various State mine-inspection departments. The cooperating agencies that contributed to make the meet a success, in addition to the National Coal Association and the United Mine Workers of America, were the Kentucky Department of Mines and Minerals, Ohio Division of Mines, West Virginia Department of Mines, Pennsylvania Department of Mines, and the Columbus Convention Bureau. SUMMARY Fourteen teams from 6 States participated in the mine rescue contest, and 55 teams from 9 States competed in the first-aid contest. Only one of these teams entered as a combination team, that is, participating in both the mine rescue and first-aid contests. The States represented and the number of teams from each State are listed in table 1.

Jan 1, 1953

By D. Harrington

United States newspapers of 25 or 30 Years ago ran headlines every few weeks telling of some mine disaster. Each disaster was a first-page attraction for a day or so then was forgotten until the next sensational event, frequently another mine disaster, a few weeks later. Interspersed with the large mine disasters were the so-called ?snipping? mine accidents that caused the death of one or two mine workers. The summation of mine fatalities of all types usually exceeded 3,000 a year, and nonfatal accidents to workers in mines of the country approximated 250,000 annually. From 1906 to 1910, inclusive, there were 84 major explosion disasters (about 17 per year) in. United States coal mines. The resulting fatalities totaled 2,388 for the 5-Year period. These frightful catastrophes helped the number of fatalities in coal mines of the country to reach the enormous total of 13,288 for the 5 years, or an average of 2,658 per year.

Jan 1, 1940

By Gabriel S. Esterhuizen, Jarek Jakubec

In 2000, Laubscher’s Mining Rock Mass Rating (MRMR) classification system was updated and published. The new system brought a few fundamental changes that were in direct response to the challenges and problems encountered when applying the classification system in the mining environment, specifically caving operations. The fundamental changes introduced into the MRMR system in 2000 were the abandonment of the Rock Quality Designation (RQD) as an input parameter, accounting for healed and cemented joints, and the concept of rock block strength. The objective of this paper is not to discuss the role and usefulness of classification systems; the fact that classification systems are widely used in every stage of mining projects speaks for itself. This paper discusses some of the experiences gained with the MRMR 2000 system in various mining projects and shows how the changes to the system have resulted in improved assessment of rock mass conditions. Issues related to core logging for rock mass assessment are also presented.

Jan 5, 2007

By Paul L. Campbell

Investigations by the Federal Bureau of Mines of methods of upgrading tar obtained by low-temperature carbonization of lignite showed that ß,ß?-oxydipropionitrile, ß,ß?-iminodipropionitrile, and ß,ß'-thiodipropionitrile were effective solvents for extracting aromatics (aromatic hydrocarbons plus polar compounds) from coal-tar neutral distillate fractions. Batch extraction showed that these solvents extracted approximately the same percentage of aromatics from various neutral oil fractions boiling between approximately 170° and 350° C. In continuous countercurrent extractions using oxydipropionitrile and iminodipropionitrile, approximately 30 to 35 vol.-pct, and 65 to 70 vol.-pct, of the aromatics in 170° to 350° C. neutral distillate oil were extracted at room temperature when solvent-to-oil ratios were 2:1 and 12:1, respectively. As the concentration of aromatics in the neutral distillate oil fraction decreased, the capacities and, to some extent, the selectivities of these solvents for the remaining aromatics decreased. Aromatics were isolated from the extracts and the solvents recovered by washing the extract fractions with a low-boiling paraffinic hydrocarbon such as heptane, using hydrocarbon-to-extract ratios of at least 2:1. The heptane wash removed most of the aromatics but only part of the polar compounds (compounds containing oxygen, sulfur, and nitrogen) from the extracts. The recovered oxydipropionitrile and iminodipropionitrile, containing polar compounds, were effective in extracting aromatics from neutral distillate oils. The contaminated solvents showed essentially the same capacities and selectivities as the pure solvents.

Jan 1, 1961

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By Wils L. Cooley

Although electric utility companies have been active in grounding and bonding within substations, the mining engineer or mine electrical engineer is not involved to the extent that he can be fully up-to-date on the most effective practices for substation construction. The coal mine power system is grounded in a fundamentally different way from most other industrial power systems and is subject to considerable Federal and State regulation. At this time, there is little information that is directly applicable to the mine situation, especially if the substation must be built in an area of limited size or in low-conductivity earth. The objective of this guide is to provide specific engineering information to the mining; industry. Using as little theory as possible, it was written to be general enough to cover most substations, but specific enough to provide direct help with each substation. It will attempt to recommend practice that is in agreement with present Federal rules and regulations.

Jan 1, 1980

By Rudy J. Matetic

Over-exposure to noise remains a widespread and serious health hazard in the U.S. mining industries despite 25 years of regulation. Every day, 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) noise level exceeds 85 dBA and more than 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the permissible exposure limit (PEL). Additionally, MSHA coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage comprise only seven different types of machines; auger miners, bulldozers, continuous miners, front end loaders, roof bolters, shuttle cars (electric), and trucks. In addition, the MSHA data indicate that the roof bolter is third among all the equipment and second among equipment in underground coal whose operators exceed 100% dosage. A research program was implemented to: 1) determine, characterize and to measure sound power levels radiated by a roof bolting machine during differing drilling configurations (thrust, rotational speed, penetration rate, etc.) and utilizing differing types of drilling methods in high compressive strength rock media (>20,000 psi). The research approach characterized the sound power level results from laboratory testing and provided the mining industry with empirical data relative to utilizing differing noise control technologies (drilling configurations and types of drilling methods) in reducing sound power level emissions on a roof bolting machine; 2) distinguish and correlate the empirical data into one, statistically valid, equation, in which, provided the mining industry with a tool to predict overall sound power levels of a roof bolting machine given any type of drilling configuration and drilling method utilized in industry; 3) provided the mining industry with several approaches to predict or determine sound pressure levels in an underground coal mine utilizing laboratory test results from a roof bolting machine and 4) described a method for determining an operators’ noise dosage of a roof bolting machine utilizing predicted or determined sound pressure levels.

Jan 1, 2006

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

By Sidney Katell

This cost bibliography, covering the period from January through December 1960, is a continuation of the series which began with the publication of Information Circular 7516 in October 1949. It is also the second report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, came from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal. Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil.

Jan 1, 1961

By Michael A. Staiano

The objective of this study was to determine the magnitude and sources of environmental noise from mining operations near populated areas, to de-scribe monitoring techniques, and to identify applicable existing noise abatement techniques. To this end, noise surveys of a representative sample of mines and quarries were conducted. Noise levels at site boundaries and near specific equipment and ensembles of equipment were measured. Noise exposures in terms of annual day-night sound level were calculated for the boundary noise measurement locations. In addition, the relative sound level contributions were estimated for the mining equipment noise sources affecting the boundary locations. Noise abatement methods falling into three categories were analyzed: equipment practices, operational/administrative practices, and equipment quieting. Selected applications of noise abatement methods were evaluated in hypothetical situations with emphasis upon machinery selection and use. Procedures for measuring noise around mining operations were provided.

Jan 1, 1981

By W. S. Sanner

Pyrolysis (destructive distillation) techniques developed at the Bureau of Mines to determine the yield and quality of the products from coal were used to convert municipal (household) and industrial refuse into potentially useful solids, liquids, and gases without adding to environmental pollution. The tests demonstrated that a ton of municipal refuse can be converted into 154 to 424 pounds of solid residue, 0.5 to 6 gallons of tar, 1 to 4 gallons of light oil, 97 to 133 gallons of liquor, 16 to 32 pounds of ammonium sulfate, and 7,380 to 18,058 cubic feet of gas. A ton of industrial refuse, consisting of paper, rags, and cardboard, can be converted to 618 to 838 pounds of residue, 1.5 to 3 gallons of light oil, 68 to 75 gallons of liquor, 12 to 23 pounds of ammonium sulfate, and 9,270 to 14,065 cubic feet of gas. The energy from the gas is more than sufficient to provide the heat for the pyrolysis.

Jan 1, 1970

Sixteen papers concerned with the technology and utilization of low-rank fossil fuels are presented as the proceedings of the 1973 lignite symposium. This symposium, the seventh in a series of biennial meetings, was cosponsored by the Bureau of Mines and the University of North Dakota.

Jan 1, 1974

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By Allen McComas, Frank Chase, Phyllip Worley

Longwall mining has gained the reputation as being the safest extraction method in underground coal mines. However, one of the most difficult tasks associated with longwall mining is moving the face once a panel is completed. Based on Mine Safety and Health Administration (MSHA) fatality reports since 1996, longwall face recovery operations have claimed the lives of 5 U.S. miners and have resulted in numerous injuries. Recovery operations can be hazardous because they involve moving large pieces of equipment in very confined spaces. They are also conducted in highly stressed ground conditions due to front abutment loads generated by panel extraction. Shield removal is the most hazardous operation during face recovery because miners are constantly exposed to the unpredictable gob edge. To protect the miners, one or more walking shields, cribbing and/or other supplemental roof and standing supports are typically employed as breaker line supports as each shield is removed. At the Harris No. 1 Mine in southern WV, mobile roof supports (MRS’s) have been used in lieu of traditional walking shields on 17 face moves since 1997. MRS’s are shield-like support units mounted on crawler tracks and are commonly used during room-and-pillar retreat mining operations. For longwall recovery, the two biggest advantages that MRS’s have over traditional walking shields are that they are remotely controlled and are highly maneuverable. MRS’s have contributed to safer shield recovery and shorter move times at the Harris No. 1 Mine. This paper will address both the safety and the operational issues associated with MRS usage during shield recovery. It will also discuss new developments, including the use of the inherently safer battery powered MRS’s, which have been recently certified by the Mine Safety and Health Administration.

By R. G. Knickerbocker, David Schlain, F. K. Shelton, J. H. Jacobs

"Many manganese ores contain from 0.1 to several percent cobalt. If such ores arc used for the production of ferromanganese, the cobalt is lost; on the other hand, if they are used for the production of electrolytic manganese, the cobalt can be recovered during the purification of the electrolyte.The production of cobalt in the United States is insignificant compared to the amount consumed, most of which is imported from the Belgian Congo. Cobalt-bearing manganese ores may therefore constitute an important reserve of cobalt in times of emergency. Moreover, the combined value of manganese and cobalt in some ores may be sufficient to warrant the recovery of both metals by the electrolytic manganese process, whereas the recovery of either manganese or cobalt alone might not be economically feasible.In view of the potential importance of manganese ores as a source of cobalt, a survey has boon made of the cobalt content of manganese ores. Most of the data have been obtained from analyses made in the Bureau of Mines, but valuable data have also been obtained from publications of the Geological Survey, various State publications, and other sources. Unfortunately, most published analyses of manganese ores do not include cobalt determinations; when such analyses were fairly detailed, but did not include cobalt, it was presumed that cobalt was not present in significant quantity.Information on the cobalt content of domestic manganese ores is given in table 1. Ores containing 0.1 percent or more cobalt are listed in table 2, and the districts in which such ores occur are shown in figure 1. Most of the known cobalt-bearing manganese ores occur in the southeastern part of the United States. A group of deposits in central Arizona and a few scattered deposits in other States also' contain cobalt."

Apr 1, 1946