Search Documents

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addresssed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1990

By Zhou Jiahan Wang Feng

This paper introduces the mechanism and the operating process of dike building by silt squeezing blasting. DBSSB (dike building by silt squeezing blasting) has the following advantages: shorter construction period (the construction period is decided only by the speed of rock materials filling)greater consolidation of the body of the dike, more structural stability, smaller settlement. Therefore by conventional standards the same dike can be designed with a smaller cross section than other construction methods, and at a reduced cost when enough rock materials can be provided in site.

Jan 1, 2006

By Cam Grundstrom

The Ok Tedi Mine is a large open pit copper and gold mine located in a remote section of the Western Province, Papua New Guinea, with an annual rainfall of over 10 metres. Ok Tedi mines an average of 205,000 tonnes per day. A strong working co-operation between the mine operator (Ok Tedi Mining Limited) and the explosives contractor (ICI Explosives Asia / Pacific) has led to progressive development of bulk emulsion formulations to meet site-specific needs, continued improvement to blasting applications, and competency based training programs for the national blast crew.

Jan 1, 1997

By Harnish Miller, Scott G. Giltner

One of the concerns with locating radioactive waste storage sites in salt deposits is how to permanently seal the underground storage areas once they have reached their storage capacity. The compaction of salt using explosives has been identified as a potential method of producing permanent seals in both entryways and shafts to storage areas. This paper describes the test procedure and results of a preliminary investigation to determine the feasibility of utilizing explosives in the compaction of salt. Three simple tests were carried out to measure the degree to which loose salt could be compacted.

Jan 1, 1996

By Pierre De Pasquale, Gilles Jauffret, Ricardo Chavez

"When blasting in quarries or mines, the main source of inconsistent results is directly related to thenon-homogeneous energy distribution through the rock-mass volume. This variation has differentorigins: drilling deviations, geometry differences from one borehole to another (burden, spacing ...),and inherent geological conditions."

Jan 1, 2016

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By Sérgio Augusto Ferreira, Alan Gerson Diaz Butron, Carlos E. Arroyo, Marcus Neves, Jorhs Enrique Casimiro Huayhua, Dieggo Santos, Eventomar Junior

The presence of natural underground cavities is normally a characteristic of iron ore deposits, specifically in tropical deposits. Brazil and the United States are the only countries that have a legislation to protect these structures, but in Brazil this legislation is very specific for the existing cavities in the federal territory. These cavities are classified by their level of relevance as high, medium, and low. From this perspective, its preservation becomes mandatory, especially, for those of high relevance in order to protect the species (flora and fauna) that live in them. When these structures are within the production phases, it becomes a challenge to exploit these reserves with the use of commercial explosives, since these structures condition and may restrict the use and amount of explosive charge. This paper presents the methodology of controlled blasting associated with predictability via realistic simulation in production polygons, applied in a Brazilian iron ore mine where there is a presence of high relevance natural cavities with restrictions in relation to the limits of Peak Particle Velocity (PPV), which is product of detonation.

Feb 6, 2023

By Alan R. Gadberry

To resolve drilling and blasting problems, rather than treating symptoms and allowing problems to grow, the mine operator needs to change the way he operates. When a mine operator discovers a drilling and blasting result that he doesn't like, it is easy for him to think of that disappointing result as a problem. More often than not, however, that result is only a symptom of a problem, and the real, underlying problem cause can be seen when the operator looks in the mirror. Symptoms and problems relating to drilling and blasting are resolved when the mine operator makes appropriate changes in the way he manages his operations.

Jan 1, 1985

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Langdon T. Mitchell, Karl Ingmarsson

The title is not referring to jewelry; nor is it about diamond core drilling. This article is instead about an emerging application for diamonds, hard rock percussive drilling with diamond drill bits. Diamond’s outstanding wear resistance has long been taken advantage of in core drilling. However, until now diamond has been less successful in hard rock production drilling in the mining and quarry industry.

Jan 1, 1999

By Marcia Harris, Richard Mainiero

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Jan 1, 2004

By Corry Goumans

Description of Project: Drilling, Blasting and Installation of Catenary Cables. Project Owner: Rio Tinto Alcan

Jan 1, 2010

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By D T. Froedge

This paper is a presentation of a coyote shot at the Oriskany Sand Quarry of the Pennsylvania Glass Sand Corporation, Berkeley Springs, West Virginia.

Jan 1, 1982

By Ravi Sahu, Kris Jeremiah

This paper aims to study the benefits of using Post Processed Kinematics(PPK) surveying methodology combined with Drone photogrammetry to achieve highly precise positioning (X, Y, Z) of drill holes based on the drill pattern and to highlight innovative workflow of transmitting the drill plan to smart drills for accurate drilling.

Feb 1, 2020

By Jody Todd, Ernesto Villaescusa, Ronald Lachenicht, Kelly Fleetwood

In the underground environment, characterisation of a rock mass during the mining cycle becomes increasingly difficult due to a lack of rock mass exposure for measurement or observation. In most cases rock mass characterisation occurs prior to mining by inspection and logging of exploration drill core, or prior to mass excavation through drive mapping for geological and geotechnical data. Characterisation strategies, if applied during the mining cycle, can reveal near-field anisotropies that may affect the behaviour of the rock mass with respect to excavation. These methods can aid in understanding the performance of stopes based on geometry, in-stope extraction sequence, and stress modelling. One such method of characterisation involves the use of production blast vibration monitoring and analysis as indicators of rock mass anisotropy through travel-time tomography.

Jan 1, 2008

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By Frank Hirthammer

The paper explains the procedure of implementing Track & Trace solutions for manufacturers of explosives based on customer experiences. By using concrete examples, the process from project start to implementation is described. Lessons learned from the experiences of European explosives manufacturers are presented.

Feb 1, 2020

By Ali Kahriman, Abdulkadir Karadogan, Umit Ozer, Mehmet Aksoy, Deniz Adiguzel

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. In bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. The prediction of ground vibration components plays an important role in the minimization of the environmental complaints. This paper presents the results of ground vibration measurements carried out in the quarries located on the different sides of Çatalca district in Turkey. In order to predict peak particle velocity level for this district, ground vibration components were measured for shots during bench blasting at these quarries. In blasting operations; ANFO is commonly used as blasting agent at the quarries. The type of priming and firing differed from quarry to quarry. The parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events by using different type vibration monitors. The absolute distances between shot points and monitor stations were determined by using GPS. The equation of square root scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. In order to predict, and compare the influence grades to the neighboring buildings, and structures at the Çatalca district, the particle velocities and frequency values of all blast events are evaluated according to the United States Bureau of Mines (USBM) and German DIN 4150 Norms due to the lack of a national standard in Turkey. Then, the data pairs belonging to these quarries were gathered together to represent the district and were analyzed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance

Jan 1, 2007