Search Documents

By Jorge Cárdenas, Alejandro Luna

In mining simulation for fragmentation results prediction is of utmost importance to study feasibility, ensure safety, and estimate the correct use of resources in drilling an explosive to meet requirements and avoid excessive usage. One critical case is fragmentation prediction, developed through models. Developing a fragmentation model in a mining unit aims to control blasting results to align theoretical and real data and improve correlation. Therefore, it is essential to collect post-blast fragmentation data, organize it, and systematically process it to develop a suitable model that meets variable requirements. Using a robust system of equations, this model should generate the required results with minimal variability between simulation and actual results. Additionally, this model must be adaptive to reduce this variability. Studying the most known and used models in mining resulted in our work correlating Cunningham 2006, Swebrec, and CZM models. Thus, the Simfrag model was created, presenting a robust foundation and combining the most notable advantages of the aforementioned models.

Jan 21, 2025

By D. Rudenko, C. T. Aimone-Martin, J. K. Ratliff, I. G. Wong, J. Aiken, R. E. Burnham, T. A. Davidsavor

A small quarry blast was conducted with a maximum of 90 pounds per delay and shortly afterwards, area residents sensed ground motion and building shaking indicative of an earthquake. In addition, seismometers up to 500 miles (800 km) away recorded a magnitude 2.8 earthquake located in the area. Positioned in a seismically inactive area, southern Minnesota is not known for earthquakes. The earthquake was originally described by the USGS to be a surface blast at the quarry. Analysis showed that the earthquake occurred shortly (approximately seven seconds) after the quarry blast some distance away and well below the surface. This paper describes the evaluation of the “seismic events” including the blast, the following earthquake, initial governmental response, and provides the framework for assessing the relationship between the blast and the earthquake. The paper also discusses management of large volume claims from a complex event and presents a claims management strategy with best practices.

Feb 6, 2023

By Sami Kara, Yunseok Park, Seung-Joong Lee, Namsun Hwang, Michael Laing

This study conducts a comparative analysis of construction efficiency. In the first part we compared electronic and non-electric initiation systems, focusing on tunnel contour holes. Field blasting operations were executed across a variety of delays to identify the optimal delay time. This delay for the in-situ rock mass was determined through regression analysis of blasting vibration in contour holes and for overbreak/underbreak. The blasting results with the electronic initiation system using the obtained optimal delay, applied to contour holes, were compared with the results of the non-electric initiation system. The overbreak and underbreak decreased by an average of 2.7 cm and 5.8 cm respectively, by using the electronic initiation system. Moreover, the vibration reduction rate in contour holes region was reduced by 11.9% based on the blasting vibration estimation equation proposed by the Ministry of Land, Infrastructure, and Transport (MOLIT). Underground construction projects have become increasing popular as cities grow in both size and density. This growth severely limits the amount of useable space for new project on the surface, resulting in the decision to build them underground. This new policy however brings into focus the challenge of managing and reducing blasting related vibration due to the proximity of these projects to sensitive structures, utilities and foundations often present in urban environments. For this purpose, we have been required to manage the vibration by reducing the quantity of explosives used per round. Inspired by surface blasting techniques, we applied a decking mode to address and work around this challenge. We present in this paper the first attempt to blast a tunnel face using a decking method and reduce the charging per hole from 6 kg to 3 kg per hole and keep the same advance rate for this tunnel. The results are presented in the third part of this paper. In the second part we present the results of the decking mode in shaft. The use of the electronic initiation system in tunnel construction provides the users an effective tool to improve the overbreak/underbreak and keep the vibration at a low level with a large gain on the overall project schedule and budget. This what we want to demonstrate in this paper.

Jan 21, 2025

By Stephen Mansfield

In open-pit mining operations, the drill and blast processes have a significant impact on the downstream operational performance of crushing and grinding of ores and recovery of metal. The blast pattern parameters, combined with the material properties, defines the run of mine fragmentation, which in turn drives the subsequent energy requirements for further processing and mill throughput. A common parameter used to describe a single hole or collection of holes is powder factor, the ratio of explosives to the quantity of material blasted. One often-neglected aspect of calculating powder factor is the explosives contained within the length of hole drilled into the top of the bench from the previous bench, known as subdrill. Explosives in the subdrill directly affect the bench below and thus do not contribute significantly to the results of the upper bench, even though they are traditionally included in the powder factor calculation. This paper presents geospatial data modelling methods that link individual holes from an upper bench to the bench below. This enables a new method for the calculation of powder factor, whereby the explosives in the subdrill from the bench above are included in the powder factor calculation of the bench below. This method allows for a clearer understanding of the impact of subdrill on fragmentation, and how variations in blast designs in the upper bench, i.e. hole diameter, burden, spacing, subdrill length, explosive type, primer position, etc., and accuracy of implementation, i.e. actual hole depths and explosive mass per hole, affect the powder factor and blasting results in lower benches.

Feb 6, 2023

By Ron Gilbert

Every day, demand increases with over all population; supply must follow. People must have more food, shelter, and mobility. Raw materials must be mined. Roads, trenches and foundations support the quality of life.

Jan 1, 1996

By Julijan Bratun, Joze Kortnik

Production of technical stone is an important economic branch in Slovenia. In 2009, we had 95 dolomite quarries, 27 limestone and 6 silicates quarries, according to the Ministry of Economic Affairs. Together they produced nearly 15 million tons of aggregates. The production in quarries is mostly performed with drilling and blasting method and only a minor part with other method like mechanical mining method.

Jan 1, 2011

By R W. Thomas

"This paper explores the possibilities of generating radical improvements in the drihing costs andproductivity of blastholes through the efforts of integrated teams as opposed to traditionalcustomer/vendor relationships."

Jan 1, 1996

By Hector O. Romero, Paulo C. Fernández A, Claudio C. Gajardo

Phase 06 of the Los Bronces mine, currently under extraction for development, has the particularity of being close to the installations and buildings of a neighboring copper mine. Therefore, the blasts must ensure the continuity of the operation without affecting the nearby structures of the neighboring district, which include Maintenance sheds and Warehouse. Specifically, the safeguards consider a scenario that includes: - Flyrock projections (<150m) - Edge profile studies - Vibrations according to the NCh3577 standard - Nitrous gases Additionally, Phase 06 is also within Los Bronces, so strict control over spillage into the pit is necessary to avoid blocking ramp access to this level. The challenge lies in protecting not only the operation and facilities of the neighboring mining district but also the operability of Los Bronces. Thus, addressing these considerations, blasting configurations are developed with prior simulation of vibration models, flyrock, and spillage in all blasts, with strict control of technical design and implementation to ensure the results. Currently, blasts are successfully executed with control of projections based on the proximity of the projects, vibration (<40mm/s) with decoupling of holes of 17 mm/s between holes, reactive rock tests for explosive selection (loading advancement), and spillage simulation inside the pit according to the loading design; thus, ensuring operational continuity and mine development.

Jan 21, 2025

By Tristan Worsey, Brad Gyngell, Todd Buschjost, Gus Diehr

This paper highlights the opportunities provided by integrating MWD data and drone generated 3D model to industries that use explosive energy to perform useful work as an integral part of their rock extraction process.

Feb 1, 2020

By Duncan Chalmers, Rob Nowell, Miguel Araos

Australian underground mines produce in excess of 60 mtpa of coal. Most of these use the longwall method, and they require the use permitted explosives (which are called “permissible” in other countries) for challenges that appear during the day-to-day activities. To obtain the approval for these explosives, they should pass Testing Memorandum #2 (TM-2), which sets out the test required for each category of permitted explosive. These categories are P1, P3, and P5. With P5 being unrestricted use and P3 and P1 have conditional use in underground mines. The TM-2 test was originally set up for NG-based permitted products around 1900. With the closing of NG plants around the world, ammonium nitrate explosives were the natural replacement, and therefore these explosives need to pass the TM2. Australia does have a P1-emulsion based explosive available. For high-risk scenarios (like blasting coal), no P5 explosives are available. The lack of P5 explosives has been prolonged for more than 25 years, since the phasing out of nitroglycerine-based permitted explosive products around the world. The main problem has been that when emulsion based permitted products are tested in the deflagration cannon, the results obtained were not considered in the TM2 criteria and therefore the tests were invalid. A research work on permitted explosives began in 2005 funded by the Australian Coal Association Research Program (ACARP). The aim of the project was to address the lack of P5-type permitted explosive (and, potentially develop them further, i.e., develop safer explosives) and understand the behaviour of emulsion explosive and the results they presented in the tests. Both bureaucratic and technical barriers appeared along the way. On the bureaucracy side, the facility was shut down, reopened, and shut down again. In view of these difficulties, assistance was sought overseas. On the technical side, from the very start the results of the tests when using emulsion-based permitted explosives were not established in the criteria, ignitions occurred for trial samples that were expected to be P5-type, etc. The aim of this document is to present the painful journey in the Australian industry to have a P5-type emulsion-based permitted explosive, for use in UG coal. Also, the technical learning acquired about emulsion explosives and the ignition path of mixtures methane / air will be shown.

Jan 21, 2025

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By Mark Bauckman

Discussion Topics • Market Needs • Technology Developments & Best Practices • Industry & Government Developments • Future Possibilities & Your Role

Jan 1, 2006

By C. Braun, C. Kennedy, P. Katsabanis

A series of small scale tests, simulating multi-hole blasts have been performed to establish the effect of delays on blast fragmentation. The blasts were performed in high quality granodiorite blocks, which were cut from stone prepared by dimensional stone quarry operations. The pattern used was equilateral triangular, with a distance of 10.2cm between boreholes, which had a diameter of 11mm, were loaded with detonating cord and the coupling medium was water. The delays used were achieved using different lengths of detonating cord for the cases of delays between 0 and 100 microseconds between holes and a sequential blasting machine firing seismic detonators for larger delays up to 4ms. All fragments were collected and screened. The experiments showed that the coarsest fragmentation was achieved with simultaneous initiation of all charges. Fragmentation became finer with delay time between holes up to 1ms between holes. The results show that in moderate to competent rock, similar to the granodiorite of the experiments, fragmentation optimization requires delays of few milliseconds per meter of burden. In view of the findings, which agree with previous published work, the current trend of selecting fast firing times for fragmentation optimization is questioned.

Jan 1, 2006

By L D. Lawrence

Certain blasting applications are more prone to the generation of significant levels of nitrogen dioxide post blast fumes, more commonly referred to as after blast smoke, generally ranging in color from dark yellow to bright red. This paper reviews basic background chemistry defining the observed fumes and attempts to correlate geology, blast design, and explosive composition effects on the level of nitrogen dioxide that can be observed in various blasting conditions. Additionally, a test setting for evaluating the generation of post blast fumes is presented with pertinent test data detailing generic explosive formulation modifications which effect the overall level of post detonation generation of nitrogen dioxide.

Jan 1, 1996

By Josee Boudreau

Transport Canada has regulatory requirements that pertain to the transportation of explosives. An important component includes the requirement for an approved Emergency Response Assistance Plan (ERAP). The ERAP may be traced to the recommendations made by Justice Grange following the enquiry into the Mississauga train derailment of December 1979. Justice Grange recommended that any shipper of dangerous goods must have a plan to control any release of dangerous goods in the event of an accident, and that the plan must be submitted to the Minister and approved by the Minister or by an organisation or person designated by the Minister. The right to ship could be withdrawn at any time if the plan is found inadequate either in its conception or in its operation.

Jan 1, 2010

By Thomas L. Barkley

"In early 2015 the Seed Waveform method was used to measure the Geologic response of the MesabiIron Formation to explosives energy input. This single charge wave form was then used to design acritical first blast at a newly developed Taconite mine. This initial blast had several irregular restrictions on design and performance. It had a very unusual “Frying Pan” shape, the regulatory agency required that no fly rock land in State owned waters less than 200 feet (61 m) away, there was no open face to blast to. Design criteria included the need to detonate the blast with two sinking cuts, and have the sinking cuts meet through a narrow neck between the cuts. All these had to be met using a 16 inch (406mm) diameter hole."

Jan 1, 2016

By Alyse Munro Hindley

The increasing negative public opinion toward blasting has led to stricter regulations and increased costs. This paper outlines alternative methods of rock excavation and the safety regulations and certification required by blasting professionals. Most importantly, however, it showcases the benefits and accomplishments that controlled blasting bring to society, giving the public a better understanding of the necessity of blasting in modern society.

Jan 1, 2015

By PHILIPP HARTLIEB, Peter Schimek, Thomas Seidl, Pablo Segarra, José A. Sanchidrián, Juan Navarro

This paper develops a new Blastability Index to assess hole-to-hole fragmentation in bench blasting based on a new Rock Factor exclusively obtained from drill-monitoring data, that can provide an automatic assessment of rock structure, strength, and waste/ore, the effective energy factor of the explosive and the delay time per blasthole.

Feb 1, 2020

By G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method. The rockmass is traversed by three to four joint sets and few minor shear seams. Rock Class “Q” values were between III and IV. Tunnel was excavated by full face parallel hole drilling blasting method. The adopted blasting method consisted of drilling 45mm (1.77 inch) diameter holes to a depth of 2m and the drilled holes were charged with 40mm (1.57 inch) diameter cartridge explosives and charges were initiated with half second non electric initiators. The perimeter holes were drilled at closer spacing of 30cm (1 feet) and alternate holes were charged using 32mm (1.23 inch) diameter cartridges explosive. Low dipping foliation joints present in the rockmass tend to slab in crown portion and erratic occurrence of intrusive bodies lead to unpredictable behavior of rock mass posing a major challenge for the safe excavation. Stability was a major issue through controlled blasting under constant supervision too could not limit the overbreak in certain weak rockmass conditions thereby exposing cavities of about 2.5m (8.2 feet). The stabilization of these cavities and handling the overbreak due to rockmass condition was time consuming and warranted additional supports. With systematic measurements and controlled blast designs the Horse Shoe Shaped Tail Race Tunnel of 9.1 m (29.85 feet) diameter and 304m (997.37 feet) length to connect with Downstream Surge Gallery of 314m (1030 feet) length, 18m (59 feet) wide and 58.8m (193 feet) height in thinly foliated and jointed biotite gneiss rockmass was successfully excavated.

By Fred Drury

I spent 38 years in the Industry in a variety of sales, technical and management positions. I started out with Hercules, then was one of the founders of ECONEX, a large regional Distributor, and finally served with Dyno Nobel as a global Vice President, based in Oslo, Norway. When I retired in the fall of 1998, I looked forward to spending a lot less time traveling and a lot more time around home. After 4 years, I’m still traveling and still wondering how to find a few more hours in the day.

Jan 1, 2003