Search Documents

By Vilem Petr

Optimization blast design parameters for rounds used at surface mines, quarries or cast blast has taken on a new importance with the increased the cost of the explosives and electronic detonators. This paper addresses the fundamentals of blast design and optimization explosive energy utilized for fragmentation. This laboratory studies shows that one key variable-the strain energy set up in rock mass by blast vibration – can be used to predict the extent of damage done to the rock strata, the degree of fragmentation of the broken rock, and the velocity of the broken rock. It also shows how the dynamic strength of the rock strata is influence the fragmentation size distribution as well as the blastability.

Jan 1, 2008

By James Goldberg, Sally Zadra, Wiliam Reisz

Early recognition and risk assessment is critical to sustaining a safe and productive blasting operation. While every blasting environment holds inherent risk, highwall blasting in highly congested areas such as Hanson Material Service Corporation’s Romeoville and Thornton quarries in the greater south Chicago metropolitan area can be particularly perilous

Jan 1, 2008

By Rahim G. Haghighi, Calvin J. Konya

Fragmentation is the fundamental concern of rock blasting and it measures the effectiveness of blasting. Fragmentation is sensitive to not only the interrelationship among the design variables, but also is sensitive to local geology. Local geologic conditions have a significant impact on the success of a blasting operation.

Jan 1, 1986

By Michael S. Wieland, Thomas C. Ruhe

Delay blasting in underground coal results in shock waves traveling through the coal that can damage delay charges remaining in the blast pattern. Undetonated explosives which are dynamically desensitized or react sympathetically from shock wave impact ruin blast results. Such malfunctions, sometimes manifest as misfires, more frequently are covert weak detonations, and result in poor coal breakage and fumes with above normal toxicity. To reduce these mining hazards and resolve charge performance problems, the Bureau of Mines has developed and tested forty prototype rugged explosives in the laboratory. Rugged explosives work properly under difficult circumstances because they not only retain their shock initiation sensitivity but also are resistant to shock damage. This research investigation resulted in one candidate emulsion explosive, formulation #37, which passed all the permissibility tests required by MSHA approval regulations. However, approval was not granted because it reached shelf-life (would not shoot properly) seven months into testing. For research purposes, the remaining tests were conducted with a second batch of formulation #37. This paper discusses the prototype rugged explosive composition and permissibility test results. Where possible, for reference purposes, comparisons are made to a commercial product that has been approved. Further research work is required to overcome the noted deficiency of short shelf-life.

Jan 1, 1992

By Park McLure, Paul Kunze

Abandoned underground mine workings have been regularly encountered in open pit mining excavations for many years, for the most part without many serious problems resulting. During the last several years however, some tragic occurrences and near misses have resulted when these old workings were intercepted. This paper will report on the problem as it relates to western open pit mining and will describe several techniques that can be used to identify problem areas before they are reached: Utilization of old maps and engineering data, long hole drilling and probing, and the use of subsurface investigation in the form of ground penetrating radar are the detection methods that will be discussed. The paper will describe some possible actions, once potential problem areas are identified. Drilling and blasting crews are usually exposed to the hazards involved when these situations arise because of their "on the ground" working environment. It is therefore appropriate that some of the best methods of dealing with these hazards once they are identified, seems to involve innovative and creative blast designs. The paper will discuss these approaches and describe an example of this aspect of the solution.

Jan 1, 1993

By Sarah Guzzelli, Enrigue Munaretti, Anneliese Botelho, Jair Koppe

Drill and Blast (D & B) is one of the main operations in the mining production cycle, which aims to fragment rock according to a pre-defined plan for proper loading, haulage and processing specifications. In this sense, data from a Brazilian iron ore mine was analyzed, given emphasis on blasthole length, subdrilling and stemming. The D & B report, including mining data such as number of blastholes, length, and diameter and stemming aspects, was analyzed in order to be able to compare these results with the blast design. The study showed significant differences between the designed blasting pattern and that one obtained by the operation. As a consequence, problems such as inadequate fragmentation, incorrect size distribution and loss of energy, were identified. For example, when stemming has a different length than it should have, noise and flyrock can occur, including inadequate fragmentation and vibration in both situations. Therefore, a comparison between the usual D & B procedures and recommended D & B design based on literature reveals the most important deviations and their consequences. The study intends to identify solutions for simple problems, improving D & B operations and safety practices.

Jan 1, 2014

By Mike McGill, Stephen Chung, Dale S. Preece

Cast blasting can be designed to utilize explosive energy effectively and economically for coal mining operations to remove overburden material. The more overburden removed by explosives, the less blasted material there is left to be transported with mechanical equipment, such as draglines and trucks. In order to optimize the percentage of rock that is cast, a higher powder factor than normal is required plus an initiation technique designed to produce a much greater degree of horizontal muck movement. This is a significant change from normal blasting practice where fine fragmentation and sufficient muck movement were the prime requirements to permit efficient excavation.

Jan 1, 1994

By David A. Paul

Over the past several years a great deal of information on blasting vibrations and their effects on structures has been generated. Much of this knowledge has been gained through the use of ground vibration measuring equipment. While this type of information is valuable and gives us great insight into damage that can be incurred by structures from this source, very little, if any, information of this quality is available for the vast majority of cases in which an engineer is called upon to investigate alleged damage from ground vibrations. For the investigative engineer, then, the problem becomes one of accumulating whatever data is available and drawing a conclusion as to whether or not the subject structure was in fact damaged by the blasting vibrations. Such an analysis certainly requires a working knowledge of the literature on the subject and as much experience as he can bring to bear. Even thus armed, however, the data is often ambiguous, confusing, and/or contradictory. A practical approach is presented herein to aid the engineering investigator in arriving at the best possible conclusion available with the information at hand.

Jan 1, 1983

By Wood Marcum, Gary McLemore, Randall Franklin

Description of Project: Nelson Brothers/Walter Energy (Choctaw Mine) Pre-Split Wall. Walter Energy – Choctaw Mine is a multi-seam surface coal mine in Northwest Alabama.Pre-splitting is the standard procedure of the Pratt Seam, which is the top seam (186 feet deep) as shown in the photo at Choctaw Mine in Parrish, Alabama

Jan 1, 2013

By Ron Fish, Cherokee Stone

Drilling and blasting in open pits is very unique in Southern Florida. Crushed limestone, the state's most abundant mineral resource, is retrieved from the bottoms of huge open pits that are completely inundated with fresh water. It is this industry that makes southern Florida the fastest growing area in the United States.

Jan 1, 1986

By Roger Favreau, Patrice Favreau

Without blasting there can be no roads, no hospitals, no factories, not even foundations for homes. Yet in 1960 the only way to design a blast was by trial/error. By comparison, bridges were already designed by calculations before being actually built. This was possible because equations based on the fundamental principles of science existed with which all the stresses in the bridge could be calculated. In 1960 no equations based on the fundamental principles of science existed with which the mechanisms that take place inside the rock mass during a blast could be calculated. Since then the main author made it the objective of his research to seek such equations, and to validate that they gave accurate answers by means of experiments in the field, experiments made in co-operation with mines, quarries and the explosives industry; results have been reported in some 90 publications.These equations now deal with essentially all aspects of a bench blast: the intensity of the shock wave and the fragmentation size distribution throughout the rock mass; the movement of all the fragments into the muck pile; the fly rock and vibrations from the blast; etc.; are presented examples of such equations. They are now assembled into a computer simulator called Blaspa accessible on the Web, with which one can design a blast just as a bridge is designed. An example is presented. The reason to design a blast by simulations rather than solely by trial/error is that if it leads to damage, it is only after the actual blast that the blast design is realized to cause damage. If however the blast design had been simulated before the blast, then the risk of damage is identified before the blast and is prevented by redesigning the blast. Examples of such situations are presented. The need to a void damage is very necessary because the public is becoming opposed to blasting. When a blast does cause damage, and people learn that the blast was designed solely by trial/error even though simulation was available and would have prevented damage, they become even more strongly against blasting; they may succeed in getting a quarry closed. Their objections to unchecked blasting are not unreasonable, especially as simulating a blast with Blaspa on the Web is a very simple procedure.

Jan 1, 2013

By Larry Mirabelli, Gerard J. O'Brien

"The construction of the Third Harbor Tunnel is a key element of the Central Artery TunnelProject. The tunnel is to traverse Boston Harbor directly linking South Boston to EastBoston. The tunnel is a cut and cover tunnel as opposed to a bored tunnel. The cutdimensions are 95' wide, 110' deep and approximately 4000' in overall length."

Jan 1, 1993

By Chantale Doucet, Mario Paventi, Malcolm Scoble, Yves Lizotte

Laboratory studies in homogeneous material indicate that the area of new surfaces created by blasting is proportional to the energy imparted to the material. Field studies, however, show that fragmentation is also related to the rockmass structure. This paper reviews ongoing compilation of a comprehensive and integrated blasting database which is based upon field monitoring and laboratory testing. A priority application of the database is to support attempts to more fully understand structural control over fragmentation. Database construction and the relative importance of rockmass physical and mechanical properties are considered in the paper. A methodology for data collection prior to, during and after blasting is reviewed. Data summaries from three case studies of blast performance in surface and underground mines are presented. These illustrate various aspects of the methodology, which included image analysis to quantify the fragment shape and remnant geology evident in the muckpile as part of the evaluation of structural control over fragmentation.

Jan 1, 1994

By Mike Cammack

Western South Dakota is predominately an agricultural area, with exception of the mining and timber industries in the Black Hills region. With precipitation rates averaging below fifteen inches per year, water is a precious commodity to the livestock industry. There is a constant demand for the construction of earthen water storage facilities (dugouts) to catch snow and rain runoff, or developing natural springs.

Jan 1, 1993

By William R. Adamson, Carlos R. Scherpenisse

The successful development of surface mining operations depends, amongst other factors, on the successful creation of final pit walls which offer long term structural stability. The achievement of such walls will be much more feasible if the mechanisms of rock mass deterioration in the mine are well understood, permitting the control and reduction of this deterioration (or damage). The role of drilling and blasting in causing damage is widely accepted but rarely fully quantified. It is also true that the dependence of rock mass damage on vibration levels is only incompletely understood and little accurate field measurement is routinely conducted in the mining industry.

Jan 1, 1998

"Blasting is an inherently destructive process and inflicts damage to the immediateperiphery of an excavation, which is later manifested as ground control and dilutionproblems. Different explosives release their energy and interact with the rock in differentways."

Jan 1, 1993

By R D. Skaggs

A good blast is dependent on a well engineered design. However, a good design's performance depends on the control of the drilling and loading of the blast holes. The key stone to good blasting is the drilling of straight holes of the correct orientation in the required positions.

Jan 1, 1991

By Harry L. Siebert, Thomas Gelormino

Rock excavation in urban areas occurs with maximum public exposure and, with the aid of explosives, is one of the challenges facing this industry today. Such excavation is also a hidden factor in areas of new growth, revitalization or upgrading existing facilities in or near urban areas.

Jan 1, 1985

By Clifton W. Livingston

This paper is the first of a series in which evidence suggesting a quantum mechanical behavior of materials in blasting and high energy impact loading is presented. Such evidence relates the mechanical behavior of materials to their electro-magnetic behavior at successive stages in the development of the electric and magnetic fields as the disturbance proceeds outward from the borehole in blasting.

Jan 1, 1981

By M Oldenburg, P J. Digby, L Nilsson

A constitutive model for the simulation of fracture and fragmentation processes in rapidly loaded rocks is studied. The model was included in a wave propagation finite element code. The results obtained from two different configurations of explosive charge and reflecting surfaces in a plane strain problem were studied. The evolution of the time-dependent fracture pattern is presented.

Jan 1, 1985