Search Documents

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By Richard A. Dick

Few topics in the blasting industry are more controversial than the proper riming procedure for large-diameter ammonium nitrate-fuel oil (AN-FO) charges, despite the considerable amount of research that has been done both in the laboratory and in the field. The January, April, and June 1975 issues of Emphasis on Blasting contain interesting discussions on priming (5). An ideal primer is one that will surely and efficiently initiate the AN-FO column at the correct location to assure optimum blasting performance. During the 20 years of AN-FO's existence, singlepoint priming, axial priming, multiple-point priming, thermal priming, and shock riming have all been advocated as the "optimum" method. This is not surprising because blasting specialists have often differed on even the most fundamental concepts. To define the optimum primer, we must know what detonation characteristics in the AN-FO column are most desirable. Again, authorities disagree. This paper will discuss conclusions of various studies in an attempt to clear up some of the confusion.

Jan 1, 1976

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By P D. Katsabanis, W Roberts

Commercial explosives exhibit non ideal behaviour which is very difficult to model. The fume spectrum produced by commercial explosives apart from its practical significance for underground mining is of great theoretical importance since it reveals information about the chemistry of the detonation process. Emulsions, watergels and dynamites were tested under various degrees of confinement in an one cubic metre closed chamber. Sand, concrete, steel and copper pipes were used to alter confinement. The degree of confinement was found to significantly influence the quantity (litres/kg of explosive) and the relative proportions of toxic and non-toxic fumes (percent of total fume measured). These results lead to further confinement testing using various rock materials. Fume results, and thus detonation performance were found to be dependent on the type of rock material used for confinement. Materials such as dolomite, limestone, and granite were found to result in a relatively high detonation efficiency of the subject explosive as shown by the distribution of detonation fume products. Conversely materials such as sandstone, talc and massive sulphide resulted in fumes suggesting low relative detonation efficiency. Fumes appear to be a sensitive indicator of the completeness of reactions occurring within the expansion zone of the composite emulsion explosive, while the detonation velocity is relatively insensitive to small variations in confinement. Estimates of sonic velocities of the confining rock materials were found to show no correlation with VOD results. However good correlation between fume results and sonic velocity suggests that the performance of an explosive as indicated by the resulting fume spectrum is affected by the degree of confinement.

Jan 1, 1992

By R C. Sittig

The manufacture of commerical detonating cord by the "wet process" technique is discussed. Raw material variability as a potential source of production problems is examined. Comparison to the "dry process" method is made. Inert samples, illustrating the cord's construction at various points in the production process, were distributed.

Jan 1, 1976

By Melvin A. Sannes

The explosives industry is recognized as one of the most dangerous occupations in the world, yet it is rare to see actual training procedures. As our industry becomes increasingly technical, it is imperative that we train the personnel in OUI industry properly.

Jan 1, 1999

By Tom Hanke, Joe Strobbe

The 80 year old Theodore Roosevelt Dam built in a scenic canyon near Globe, Arizona is currently undergoing a major renovation. The old stone dam, built by hundreds of skilled stonemasons, is being covered with a new concrete face that will increase the dam height by 77 feet. The renovated dam will improve flood control and provide increased electrical power and recreation area. The contractor, J.A. Jones is constructing the new dam and powerhouse for the Bureau of Reclamation.

Jan 1, 1993

By RR Vandebeek, A W. Bauer

The Canadian Explosives Research Laboratory regularly evaluates the properties of commercial explosives for authorization under the Canada Explosives Act. Propagation sensitivity is normally measured using small scale tests. Relating the results in actual mining practice is difficult. In the mining industry, the propagation sensitivity is a measure of the ability of one cartridge to propagate to an adjacent cartridge in a borehole. They may be separated by a gap of in-filling material. As well the propagation sensitivity will be affected by the explosive type, temperature, degree of coupling, cartridge diameter and other factors.

Jan 1, 1987

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Michael S. Wieland

Delay detonators that are damaged by cross-hole wave interactions degrade blasting work and raise the risk of incidents. Damaged detonators impose risk, because they can retain sensitive explosives that respond to stray energy during recovery, inspection or disposal. Laboratory techniques were developed to rank the ruggedness of delay detonators under replicated field-shooting conditions. The hazards are tremendously magnified if trial detonators are installed directly in secondary explosives to rank initiation strength. Therefore indirect ranking techniques were sought that mitigate the risks without compromising the worthiness of the method. Four types of hardware fixtures, referred to as simulators, were developed to yield distinct forms of transient compression. The shock and rift versions generate compression pulses representative of in situ waveform components. The waiting time, until the trial detonator functions, duplicates typical delay periods. The trial detonator is mounted within water, which has a density and inertial resistance comparable to most blasting explosives. The work output from the trial detonator explosion is registered as fixture wall-expansion. This work output determines malfunction results, regardless of which type of simulator is used.

Jan 1, 1997

By Mike Wheat, Catherine Aimone-Martin, Brandon Pease

The Kneeling Nun rock pinnacle is a prominent landmark, 90 ft in height and 35 ft in width, that resides on a bluff overlooking the Santa Rita pit at the Chino Mines Co. operations near Silver City, New Mexico. The company plans to expand the current pit limits, resulting in a change in direction and distance of hard rock mine blasting operations in relation to the pinnacle. Concerns about the stability of the pinnacle adjacent to mining activity has prompted company personnel to enhance the seismic monitoring program both on the pinnacle and along the current open pit highwall that forms the base support below the pinnacle foundation. This paper presents the vibration response characteristics of the pinnacle, in terms of amplitude and natural frequencies of motions and damping characteristics, for measurements recorded at the top and base of the pinnacle. The influence that blasthole initiation timing and sequence of hole detonations have on vibration response is discussed. A simple analysis is made to estimate factors of safety against cracking of the landmark as well as blast-induced slope instabilities within the foundation rock.

Jan 1, 2000

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By Rick W. Bellenie, Ronald L. Woolf

The Gregg River mine is located 40 kilometres (25 miles) south of Hinton, Alberta, approximately 330 kilometres (205 miles) west of Edmonton and lies against the Front Range of the Rocky Mountains.

Jan 1, 1994

By G E. Exedaktylos, Y Zhou

The complex and non-linear nature of blast fracturing has restricted common bract design primarily to empirical approaches. The code developed for this investigation simulates the pattern of interacting radial fractures from an array of blastholes, at various burdens and spacings, and in simultaneous and delayed modes. The resultant pattern is analyzed and a fragment adze distribution calculated.

Jan 1, 1989

By Richard N. Snyder

In this system for connecting blasting caps to the initiation source, the need for a redundant design structure provides more reliable method of explosive initiation. This is accomplished by using a complete system starting at the blasting control, through the initiation line structure through the initiation line and connecting blocks to the blasting cap. The connecting structure between the initiation device and the blasting caps may be connecting blocks or other means.

Jan 1, 1995

By Jacques Monette, P K. O'Connell, Keith Boyle

The mine contracting industry in Canada is no different from any other industry in its quest for productivity improvements. Dynatec Mining Ltd. has focused on drilling and blasting of rounds as an area for improvement. This paper describes the development of blasting long rounds in shaft sinking as well as a description of the lateral excavation system as applied at Aur Resources Inc., Louvicourt Project.

Jan 1, 1994

By Yoshiharu Tanaka, Keita Morooka, Masaaki Yamamoto, Katsuhiko Kaneko

Smooth blasting is the standard method for underground rock excavation, to reduce over break and remaining rock damage. We already utilized the high accuracy of the electronic delay detonator to investigate its effect on over break remaining rock damage, and surface smoothness. And we presented at 11th annual symposium on Explosives and blasting Research.

Jan 1, 1998

By Daryl Andershock, Paul Worsey, Brandon Weeks, Kurt Kosman

Several derivatives of soybean oil are currently manufactured and sold on the open market. Of these, the use of methylsoyate as a direct fuel substitute in diesel engines has been thoroughly researched and practically applied. The use of this product as a fuel gave rise to the idea of using a similar substitution in ANFO blasting agent. The first year of a three-year research program has been sponsored by the Missouri Soybean Merchandising Council. The project is funded for the purpose of opening up of new markets for Missouri soybean products.

Jan 1, 1997

By Carlos Agreda

A general review of the comminution theory and also the general differential equation of the comminution are described, analyzed and discussed in order to be applied to rock blasting. Some size distribution functions are reviewed and discussed to determine which of them represents better the cumulative low size distribution F(x) as a function of the nominal particle size (x), for the rock blasting fragmentation. Based on the mathematical comminution model before presented a formula to calculate the burden (B) is developed and discussed.

Jan 1, 1994