Search Documents

By Gruenewaldt von

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. The principles of shear-driven aggregation of particulate matter suspended in fluids, a common industrial method of concentration and separation, were applied to a convecting magma to estimate the time required to sparge or strip the PGE and Cr content and concentrate it into the boundary layers. It was calculated that an ore-grade (e.g. 6 ppm PGE) boundary layer about 1 m thick would require 100 000 years at most to form from a body of magma 500 m deep with a PGE content of 20 ppb. Since concentration would be most vigorous when the magma was warmest, at least half of this concentration would take place in the first 10 000 years. The effect of dispersive pressure in the boundary layer would generate a concentration high of refractories just below the top of each boundary layer and another just above the bottom. If the magma was a double-diffusive system, it might evolve by the downward cascade of enriched boundary-layer material into the hotter, lower magma layers, where depending on saturation levels chromites would equilibrate and sulphides undergo partial or total resorption, enriching PGE levels in any remaining sulphides. This cascade process would in time greatly enrich the lower regions in PGE-bearing sulphides and chromites

Apr 1, 1994

By A. M. R. Neiva

The WNW-ESE-trending hydrothermal veins cut alternating mica schists and quartzites of mainly Ordovician age and, to the west, a Hercynian muscovite-biotite granite. They have been prospected and developed to a depth of 300 m and reserves of 20 t Au estimated. The paragenetic sequence and chemical compositions of the ore minerals are generally similar to those at Jales to the south. Gold, electrum and aurian silver form inclusions in arsenopyrite, pyrite, galena, sphalerite, pyrrhotite and quartz and also occur in veinlets that cut these minerals. Silver has been found in gold, electrum, aurian silver, tetrahedrite, freibergite and the Ag-Pb-Sb sulphide owyheeite. Early arsenopyrite crystallised at an estimated 480 degrees C and the more common, later arsenopyrite in which Au and Ag are generally included at 430-300 degrees C. Sphalerite crystallised at 307-100 degrees C. Monoclinic pyrrhotite may have been formed by the inversion of hexagonal pyrrhotite at 248 degrees C

Jun 16, 1905

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

By A. G. Pasamehmetoglu, N. Bolukbasi, O. Koncagul

A study has been undertaken to establish the relationships between the O&K wedge test cutting resistances and the geotechnical parameters of rock materials in the context of bucket-wheel excavator operation. Prediction equations were formed to estimate the cutting resistance from the geotechnical parameters by multiple regression analysis. The cone indentor index, uniaxial compressive strength and Shore hardness parameters have been found to be the most significant predictors

Sep 1, 1991

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

By G. G. Roy, R Shekhar

Pachuca tanks are extensively used for the cyanide leaching of gold and the carbonate leaching of uranium, processes in which oxygen mass transfer plays a very important role. Experiments were carried out to clarify the effect of design and operating parameters on oxygen mass transfer. Parameters such as the ratio of tank height to tank diameter, the ratio of draught-tube diameter to tank diameter and the tank design were found not to influence oxygen mass transfer. Results also showed that equal superficial gas velocities may be used as a criterion for scaling up oxygen mass transfer in both full-centre-column and free-air-lift Pachuca tanks with clear water. A volume-averaged, volumetric gas-liquid mass-transfer coefficient (k'av) was used to characterise oxygen mass transfer in full-centre-column tanks. The axial dispersion model was used to determine k'av. The resulting model used only tank geometry and air flow rate as inputs for the prediction of k'av in industrial-scale tanks. Predictions from the model show clearly that "local" mass-transfer coefficients, measured at one or two locations, may not adequately represent gas-liquid mass transfer in industrial tanks. It is therefore necessary to obtain an estimate of k'av

Jun 18, 1905

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By J Hadijigeorgiou, R. W. Lawrence, R Pouling

The layered co-mingling method involves the disposal of waste rock with the addition, at predefined construction stages, of layers of dewatered mine tailings. The resulting waste structure displays bulk properties that are more favourable to acid rock drainage (ARD) control than the constituent materials alone. A laboratory test programme was conducted to examine the potential of this method. Columns containing different configurations of waste rock and tailings were percolation leached for 40 weeks and the leachates examined for various parameters. In the short term the chemical reactions that result from the introduction of dewatered tailings into rock waste can significantly improve the quality of the drainage. Columns with co-mingled material produced leachate with pH levels of 8, whereas leachate from the control column containing waste rock alone had a pH of 4. Larger-scale field tests are planned to determine the effect of the disposal method over the longer term

Apr 1, 1996

By G. X. Wang, R. E. Siemens, M. C. Fuerstenau, D. Chandra

Soda roasting of concentrates from Mouat, Montana, was performed in a temperature range of 450 to 650 degrees C and chromium was solubilised by water leaching at room temperature. It was found that high extraction yields of chromium were primarily dependent on the conversion of Cr3+ to Cr6+ during the roasting step, and this was enhanced significantly by simple attrition of chromite particles during this step. Gangue impurities (mainly Si) were more detrimental to Cr extraction than lattice impurities such as Al or Mg. It appears that oxidation proceeds into grains along a preferred crystallographic plane in the cubic lattice of the chromite. The effects of roasting time, temperature, soda to chromite ratio and particle size on the extraction of chromium are presented

Jun 18, 1905

By Briggs H.

The illustrated device uses the principle that the lamp can burn with a smaller inlet passage if the air is rich in O2 and that the size of the inlet can be made a measure of O2 percentage. The appliance consists of an adjustable cut-off applied to the inlet of a safety lamp of the improved Gray pattern. Precision is assessed from tables of calibration tests in air contaminated with blackdamp of CO2:N2 composiiton 1:5.67 at temperatures of 40-70 degrees F. Results are presented of tests at St. Germain's colliery, of tests in air contaminated with pure CO2 and of air contaminated with both blackdamp and inflammable gas; published ranges in mine-air blackdamp compositions are tabulated as ranging from 90.06% N2 to 43.90% CO2. When firedamp is present at 1.25-2.5%, its content must first be estimated by means of the cap and a fifth of its value then deducted from the lamp reading for O2

Dec 1, 1916

By P. H. Carr, G. G. Marino, K. A. Patel

Extensions to a correctional institution at Wabash Valley, Indiana, required development over abandoned coal-mine workings, at 90 m depth, where subsidence was possible at surface. Backfilling of the flooded mine in critical areas was determined to be the most cost-effective method of limiting the risk of damage to the buildings. Containment grout was first placed in selected entries and cross-cuts of each mine area; the remaining volume was then filled with a readily flowing infill grout. Where a high proportion of an area was taken up by rubble, calcium lignosulphonate was used as a retarder and plasticiser to increase penetration. Grout movement was monitored from adjacent boreholes with an electrical resistivity probe during grouting, while after the work was finished core samples were obtained from verification holes drilled in the backfilled areas

Jun 19, 1905

By M. Gallego, R. Oyarzun, L. Ortega

Evidence of metallogenic activity in an area dominated by Upper Precambrian and Palaeozoic metasediments was partially explained in the 1980s when drilling and a geophysical survey detected hidden intrusions, but questions remained to be answered about the nature of the fluids. Sb mineralisation at El Juncalon vein-type deposit was selected for geological, geochemical and fluid inclusion studies as a model with a relatively simple quartz-stibnite-pyrite paragenesis. Many of the characteristics were those of Chinese-type vein Sb deposits, which can be regarded as atypical of the epithermal type as they are hosted by clastic rocks

Aug 1, 1995

By P. H. Williams, D. J. Morris

The co-disposal of coarse and fine coal wastes by combined pumping through a pipeline to subaerial deposition was pioneered in Australia in 1990 by Jeebropilly colliery in Queensland. Significant segregation of fines is found to occur in its co-disposal delta, leading to the formation of distinct mainly coarse upper and fine-dominated lower segments; the upper delta drains rapidly and is able to support traffic on its surface immediately after deposition. An existing theory of subaerial deposition, originally developed for mine tailings alone and later extended to trial co-disposal, is shown to apply also to the upper segment of the full-scale Jeebropilly delta

Jun 19, 1905

By D. Bitzios, A. Gracia, V. Meggiolaro, J. D. Baker

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A large deposit in Spain and several smaller ones in Greece and Sweden were investigated. Beneficiation testwork, including the development of an innovative wet circuit, was undertaken in Italy. The Spanish Ilustracion deposit lies occurs in thin, white layers throughout a zone 35-40 m thick and 1.5 km long, in laminated calcsilicates. Total resources of more than 100 000 000 t include proven open-pittable reserves of 4 500 000 t averaging 35% wollastonite. The beneficiated product is suitable for various applications, including ceramics. The Swedish and Greek marble-hosted skarn deposits include Albatross, with 2 500 000 t of reserves at 30% wollastonite, and Panorama, with reserves estimated at more than 700 000 t

Jun 21, 1905

By M. W. Grabinsky, M. S. Diederichs, E. Hoek

Provided that they are used correctly, numerical models can be of considerable assistance to mining engineers in designing underground excavations. Guidance is given to the engineer or geologist who is not a specialist in numerical analysis but who is interested in using numerical modelling tools or in employing someone to analyse the stresses, displacements and failure in the rock surrounding underground excavations. A description of the theoretical background to a number of these numerical models and discussion of the advantages and disadvantages of each are followed by guidelines on the selection of appropriate models for each stage in the development of a mine, from exploration to the completion of mining

Jan 1, 1991

By M. Bustillo, S. Ordonez

"Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The Mississippi Valley-type deposits occur in massive, homogeneous dolostones from which diagenesis has obliterated all primary sedimentary structures. The mineralisation forms irregular, lens-shaped stratabound bodies, mostly in the lower part of the dolostones. They are composed exclusively of sphalerite, galena, pyrite, marcasite and barite, with white sparry dolomite a common cementing phase. Mineral zoning can be recognised from pyrite and marcasite in the east to barite in the west. Sphalerite, the most common sulphide, occurs basically as colloform and banded crusts and galena as isolated cubic or skeletal crystals, mainly in the centre of the banded botryoidal sphalerite. The combined observations of the deposits' geology, geochemistry and ore petrology suggest a three-stage genetic model: carbonate sedimentation in a shallow-water environment; dolomitisation, probably after compaction, by fluids of connate origin and lateral evolution; and mineralisation by migrating solutions, perhaps related to oil-field brines, that originated in deep zones of the basin during diagenesis of the basinal mudrocks in the NE"

Apr 1, 1995

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By J. A. Finch, Zhenghe Xu, Z. A. Zhou

Whether the microscopic bubbles generated by the high energy dissipation and high feed-slurry velocities in new flotation cells are stable in solution and what roles they play in particle collection are of great interest for the flotation of fines. Experimental work has shown that, with fast flow of liquid through an orifice, stable microscopic bubbles can form in flotation systems by hydrodynamic cavitation in the absence of gas supersaturation. The minimum flow rate at which bubble formation is initiated varies from 8 to 15 m/s, depending on the design of the cavitation tube, which is within the range of feed slurry velocities of some newly developed cells. Feed aeration enhances the formation of micro-bubbles by hydrodynamic cavitation. The study suggests that the fast flotation kinetics of some new cells may be attributed in some degree to the formation of microscopic bubbles

Jun 21, 1905

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By M. K. Abd El-Rahman

A complete chemical analysis of the waste showed that it contains 15.64% P2O5; X-ray diffraction analysis revealed that it is composed mainly of francolite, calcite, pyrite, quartz and dolomite. The phosphate values were recovered and the settling rate of the wastes enhanced by the use of hydrocyclone and flocculation techniques. The hydrocyclone produced an underflow enriched in phosphate and an overflow enriched in clays. The former represented 39.8% by weight of the phosphatic clay waste and assayed 26% P2O5 at a recovery of 66.36%. The results of flocculation of the phosphatic clay waste showed that both the degree and rate of settling were increased and that the process water could be recycled. The settling rate was 37 times greater when anionic polyacrylamide A130 was used

Jun 21, 1905