Search Documents

By N. T. Moxon, D. Mead, S. B. Richardson

A laboratory and theoretical study of air decks was carried out to assess the effects of the size and location of air-decks on fragmentation. The degree of fragmentation was found to depend on both factors. As the size of the air-deck increases the degree of fragmentation is reduced relative to a full column charge. However, the reduction is relatively small until a critical size is exceeded. The critical size depends on the strength and structure of the surrounding material. A critical air-deck length of 30-35% of the original explosive column was determined for the model materials used in the study. A theoretical explanation of the results was derived based on pressure decay rate relationships. The location of the air-deck also influences fragmentation. The interaction and oscillation of the two shock fronts from the top and bottom charges mean that mid-column air-decks produce better fragmentation for the same air-deck length and explosive loading as top-column or bottom-column air-decks.

Jan 4, 1993

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By R. J. Pine

Procedures are described for the application of risk analysis or probabilistic methods to mining geomechanics. The methods are widely applicable to existing mine design models. Detailed examples are given of plane slope failure and of pillar design based on displacement-discontinuity stress modelling and empirical strength assessment. The modelling techniques assessed are the Latin hypercube sampling method, incorporated in a spreadsheet environment, and the general point estimate method (GPEM), programmed in TurboBasic. An example GPEM program listing is included. Both methods are very convenient to use. Probabilistic acceptance criteria for slope stability after Priest and Brown are examined and alternatives are proposed where output distributions of factor of safety are approximately normal or lognormal and output distributions of safety margin are normal. The reliability index is included as a useful measure of variability with proposed acceptance criteria.

Jan 12, 1992

By R. F. Bell, Schultz

The paper briefly discusses the nature of spontaneous heating in mines in the Doncaster area, in the period immediately before 1967 and steps taken to prevent and treat such outbreaks. The changes that led to the increased rates of advice of Barnsley Seam faces since 1967 are listed and the effects of these increased rates on the frequency and location of spontaneous combustion are discussed. The change in methods of control required by the increased rate of advance of the faces and the changes in location of outbreaks are described. Some typical heating situations are evaluated. The methods described include the use of air sealants, water gels for filling of voids in wastes, the balancing of pressures across heating areas by pressure chambers, booster fans, and the resiting of air separation doors, and the sealing of air-ways by flooding. The authors discuss the influence of mine layouts on the risks of spontaneous combustion and advocate that future plans should be designed to limit the number of districts at risk when heatings occur.

May 23, 1905

By Fearnsides W. G.

The second part of the paper, presented at the Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, addresses the post-Carboniferous and pre-Permian movements which brought about the partition of the area and gave to the North Midland district its individuality as a separate coalfield. As earth-movements of several ages subsequent to the Carboniferous have played a part in the formation of this particular coalfield, the aim is to elucidate the effects which belong to the post-Carboniferous and pre-Permian Period and to disentangle them from those of later date. This is done by comparing the geometry of the folded surface of one of the more important horizons in the Coal-Measures with that of the surface of unconformity which divides the Permian from the Carboniferous rocks in South Yorkshire, Derbyshire, and Nottinghamshire

Dec 1, 1916

By E. H. Baker

Vapour pressures of sulphur have been measured over the temperature range 340-1039°C by means of boiling-point measurements, an internally heated pressure vessel being employed with argon as the pressure medium. The results are expressed satisfactorily by a four-term pressure-temperature relation. At the cited critical temperature of 1040°C the calculated critical pressure is 204 atm. From the pressure-temperature relation and available thermal data for the vapour, the approximate composition of the saturated vapour in terms of the various molecular species has been derived for the critical point

Dec 1, 1971

By C. C. Harris

The two best known graphical methods for presenting and comparing comminution data are obtained by linearising the Gates-Gaudin-Schuhmann and the Rosin-Rammler size distribution equations. It is shown that the Gates-Gaudin-Schuhmann equation can cause excessive congestion in the 50 per cent oversize range and that, overall, the Rosin-Rammler is a better procedure. Examples are given

Dec 1, 1971

By John Craw

This paper has formulated the methods, both medical and engineering, for the control of pneumokoniosis in the haematite-mining industry in West Cumberland, but this is only part of a general service to improve the lot of the worker in these mines, to make him a better and happier workman, and to permit him to enjoy his work and leisure in comfort and good health. This organization has now been functioning for more than ten years and the results are indeed heartening, but it is only as a result of constant vigilance from the mining and medical point of view that such a plan can operate efficiently. The human element and its full understanding is by no means the least of the problems.

Jan 1, 1947

By R. J. Bridges

Mining operations on the Witwatersrand are conducted for the most part in rocks of highly quartzitic character. They comprise the following types: Conglomerates, grits, and quartzites, to which on the Far East Rand must be added fine-grained quartzitic shales and shales. In addition, vein quartz occurring as small veins, veinlets and fissure fillings, and igneous rocks forming dykes, must be mentioned, although they constitute only a small percentage of the rock broken. The following is an account of the character and mineralogical composition of the various types.

Jan 1, 1947

By C. C. Harris

The use of Alyavdin's equation Y(x,t) = 1-e(-bt) for describing the effect of grinding time on size distribution is discussed. The equation transforms into linear form by expressing it as log-log reciprocal (1 - Y) versus log t. For plotting, specially divided grids are available; Rosin-Rammler or Weibull charts may be used. The data of Herbst and Fuerstenau are especially useful for illustrating the Alyavdin-Weibull chart in two applications: (1) presenting data (which are relatively unaffected by experimental scatter) and comparing them with theoretical predictions, and (2) as a test for the zero-order kinetics production hypothesis. The chart based on the Alyavdin-Weibull equation is suggested as a useful aid in the analysis of kinetic data (/ versus f), though not as a procedure in its own right. Proposed applications are (1) displaying data with excellent clarity, since it avoids the kind of congestion inherent in some other plotting methods, and (2) as a test for assumed kinetic relationships. Sometimes, equation 1 describes the data quite closely, and in these cases the parameter values appear to be related to certain operating conditions.

Dec 1, 1971

By E. L. Evans

The historical development of South Yorkshire mining is traced and note made of the liability to generate spontaneous combustion of some of the seams which have been worked. The liability factor is analysed firstly as an inherent property in the material of a coal seam, and secondly as a circumstance of a situation in which access is provided for the air necessary to sustain oxidation. The geological settings in which incidents of heatings have been known to occur is discussed and conditions favouring a natural pre-disposition to spontaneous oxidation exposed, particularly the effect of argillaceous material overlying the seam. An extensive strata-dynamic study follows to demonstrate the situations in which stray air currents tend to impinge on readily oxidizable material. Prevention techniques are indicated as the identification of strata-dynamic situations in which air access to broken coal is induced and thereafter th operational action to seal off the voids which have been opened up so as to exclude air from the broken coal. Measures to reduce the tendency for ventilating air to short circuit across waste voids, and to obviate deflection of air into packs are outlined. The importance of face and roadway design features is demonstrated and the consequences of practices inimical to good control of spontaneous combustion are related. Discussions on means of detection and also on the sealant materials available are included.

May 23, 1905

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By P Cochrane

Our ability to generate information and transport it about the planet on super highways of optical fibre is about to change the way in which we communicate, work and live. There is not a single aspect of our future that will go untouched by the communication and computing revolution that Is now upon us. The change we are about to witness will overshadow the impact of the printed word, industrial revolution and physical transport. The next major wave of information technology (TT) development will focus on the delivery of information and experience on demand, in the right form, at the right time, at the right price, to fixed or mobile terminals anywhere, over networks of optical fibre, radio, satellite and optical wireless. Bandwidth, distance and time will no longer be significant cost elements as service and access become dominant.

Jan 7, 1996

By Walshe J. M.

The slow-speed compressor is giving place to the high-speed type, with its greater economy of material and space; and, where very large units are required, the turbo-compressor is supplying the need. In the very large air-supply stations on the Rand, turbocompressor units of a capacity of 20,000 and even 50,000 cubic feet, requiring 4,000 to 13,000 horsepower, are quite a commercial proposition, and have proved a practical success. Air-compressors of this size are, however, very exceptional, and the high-speed reciprocating compressor is quite capable of dealing with the highest outputs so far required in this country and, in the hands of manufacturers experienced in the design of high-speed steam-engines, a very high standard of reliability and efficiency in operation is obtained. The so-called “high-speed” or more correctly quick-revolution type of compressor is now extensively used in mines and collieries; for the air-pressures required for power purposes in mining work, two-stage compression, with an intercooler between stages, is the design usually adopted in best practice. It is not the writer’s intention to describe a variety of high-speed air-compressors but to select as an example of this type of compressor the one with which he is most familiar, and which is probably more largely used than any other, namely, the double-acting two-cylinder two-crank type with automatic light-plate air-valves, and with the working parts lubricated on the forced-lubrication principle. Sectional drawings, efficiency curves, air-cylinder diagrams and other data accompany the descriptions and photographs of compressor design, components and mine applications

Dec 1, 1916

By J. V. Wood, P. Davies, J. L. F. Kellie

A new range of wear-resistant materials is being produced by technology that has been used to develop high performance metal-matrix composites. These include steels and aluminium alloys that can be made as sheet, plate, rod or bar. The incorporation of hard, wear-resistant particles in an alloy matrix is achieved by reactive casting, spray deposition and powder metallurgical techniques. For example, large particles of TiC can be homogeneously distributed in steel during casting and the subsequent product can easily be rolled to plate. Similarly, up to 20% alumina particles and SiC can be injected, respectively, into steel and wear-resistant aluminium alloys by spray deposition. The current state of development of the process is reviewed and indications are given of the projected applications of such materials.

Jan 12, 1992

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997

By Groom P.

The wastage of timber in coal-mines that is caused by decay is very great; in fact, far greater in this country than is generally realized. Mr. E. W. Peters estimates that of the whole wastage of timber in mines in the United States of America, 50 per cent, is due to decay and insects; of this 50 per cent, an overwhelming part is due to decay. The most efficient methods of decreasing this grave loss can be devised only by co-operation of the mining engineer and the scientific expert, and it is partly in the hope of procuring such collaboration that this paper is written. It contains, therefore, a resume of our present knowledge of the decay of wood, and of the economic methods of checking this in mines; but, with a view to improving those methods, it also directs attention to the gaps in our knowledge and the means by which these can be filled by future investigation

Dec 1, 1916

By Dobson C. L.

The memoir, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne on 3rd June 1916, outlines the career of one of the Institute's oldest members and past-president 1896-1898, including the improvements he introduced at Harton, St. Hilda and Boldon collieries and his activities with the Institute and the Durham Coal Owners' Association

Dec 1, 1916

By A. Ludkin

The paper presents the history of the occurrence of spontaneous combustion in the north area, together with the associated problems. These are examined and a description is given of the methods used to combat the danger, including the use of modern scientific instrumentation. Detailed reference is made to the underground trials with pack injection and sealant coatings which were carried out at Seafield Colliery following the formation of a working group to assess the performance, in the same underground conditions, of (1) sandbagging, (2) pack injection, (3) surface coating. Based on these trials, an improved and more economical method of prevention has been established. There is, however, still scope for further improvement in techniques which would take into account the problems of gradient, transport, manpower and cost.

May 23, 1905

By D. J. Buchanan

British Coal's mining research programme is directed towards the strategic objectives of reducing production costs, improving product quality and resolving health, safety and environmental issues. The strategy for R&D is described and selected parts of the programme are reviewed. Two major initiatives are directed towards reducing production costs: geotechnics and automation. Integrated exploration techniques are used to delineate geological structures as an aid to mine planning. Rockbolting is being rapidly introduced and the in situ stress field has been found to be of significant influence. Automation is the subject of a major programme. A strategy for coal quality has been devised. The health, safety and environmental programme concentrates on the traditional hazards together with surface environmental problems.

Jan 12, 1992