Search Documents

By S. H. Morar

Froth flotation is a physico-chemical separation process that takes place in two phases; pulp and froth phase. It is widely recognised as a complex process, due to the range of interactions present within the system. Of critical importance is the role of the froth phase within the system. The pulp kinetics governs the maximum potential recovery within a flotation cell, while the froth phase governs the selectivity via the froth?s stability. Higher froth stability improves recovery at the expense of grade, and lower froth stability improves selectivity. It is well known that the two major factors affecting froth stability are attached particles and solution chemistry. This paper looks at a flotation bank at different froth depth and frother concentrations. The air recovery to the concentrate is determined at each condition and relates the effect of the operating conditions on froth stability and transport to the amount of solids that are recovered to the froth and concentrate by true flotation. The results presented show that, for a given process objective, which in this case was a consistent mass pull profile, depending on the operating conditions, solids recovery in the pulp is affected by the air rate required to maintain the target mass pull. To a smaller extent, the changes in the pulp composition affect down-stream pulp recovery. The variation in solids recovered into the froth drives the froth stability at the start of the flotation bank, while the frother drives the froth stability at the end of the bank. The performance in between these two extreme conditions arises from an interaction of these two effects. The consequences of these interactions can give rise to counter-intuitive responses that can confound efforts to optimise the performance of the bank.

Jan 1, 2014

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By H. H. Li

Reverse flotation is usually used for hematite/silica or bauxite/clay flotation separation in which the silica or clay is floated and rejected. Some properties of these silicate minerals such as particle size and surface characteristics have significant effect on their flotation behaviours. Firstly, the silicate mineral particles (especially clay minerals) generally have fine particle size (< 5 microns) in their natural states or due to overgrinding and they display poor flotation kinetics, consequently having low flotation recovery. Secondly, the wettability difference on different particle basal planes influences the affinity for adsorptions of different types of chemicals such as collectors or macro-molecule. Common polyacrylamide (PAM) flocculants can be used to minimize the exposure of the most hydrophilic planes of clay particles via hydrogen bonding but they can not efficiently enhance the overall particle surface floatability due to the hydrophilic properties of this type of macromolecules. A novel method to improve both flotation kinetics and surface wettability of silicate minerals has been developed and studied. That is to use a temperature-sensitive polymer, poly (N-isopropyl acrylamide) (PNIPAM), as a process aid in the flotation of silicate minerals. Unlike PAM polymers, PNIPAM can induce a hydrophilic/hydrophobic transition on the particle surface when the temperature is changed to be lower or higher than its critical solution temperature (CST). At a lower temperature, the PNIPAM adsorbs on the particle surface via hydrogen bond similar to PAM. It induces strong hydrophobic aggregation when the temperature is increased above the CST. Thus, both floc size and mineral floatability are greatly increased. The flotation results show very good flotation performance and the addition of conventional flotation collector was no more required because the increased particle surface hydrophobicity induced by PNIPAM. Contact angle measurements explained the role of PNIPAM in manipulating particle surface hydrophilic/hydrophobic transition.

Jan 1, 2014

By Ingvar Ymén, Alexandra Lundmark

"The depressive effect of dichromate on galena was evaluated with chemical experiments and small-scale depression experiments at a pH of around 12. The depressive effect was measured with Dynamic Vapor Sorption (DVS), which measures the water uptake of a sample as a function of the % relative humidity. The depression is due to PbCrO4PbO, which in the presence of Ca2+ and SO4 2- forms a more or less amorphous solid solution (Pb,Ca)(CrO4,SO4)PbO, which clogs to the surfaces of the ore. Free Pb2+- ions are needed for depression to occur and at high pH Pb2+ - hydroxide complexes, supply enough Pb2+ - ions to precipitate (Pb,Ca)(CrO4,SO4)PbO. In air CO2, precipitates CaCO3 which slowly lowers pH, precipitating more (Pb,Ca)(CrO4,SO4)PbO and CaCO3 on galena. Similar experiments where performed with five alternative depressors whereof phosphate, which forms an amorphous precipitate of approximate composition Pb3Ca13(PO4)10SO4, gave the best results. Phosphate was tested in laboratory scale flotation experiments giving encouraging results.INTRODUCTIONWithin Boliden Mines, concentrating of copper and lead from complex sulfide ores is performed by bulk flotation, meaning that copper and lead are concentrated in the same product. Downstream, copper and lead are separated by flotation of chalcopyrite, and depression of galena. Boliden has for many decades used sodium dichromate to depress galena (reference 1). Dichromate is both toxic and carcinogenic and Boliden has for many years investigated several alternatives. So far, however, the best results have been obtained with dichromate. Since Boliden has tried to substitute dichromate for a long time without finding a process as effective, Boliden decided to clarify the function of dichromate in the depression of galena and on the basis of the outcome find alternative depressors with similar function. This study was given to RISE Bioscience and Materials / Surface, Process and Formulation as a consultancy assignment. This paper presents the outcome of the combined efforts of Boliden and RISE."

Jan 1, 2018

By Y. De Gao, C. Gang Zhong, X. Yang Qiu, Li Wan

The chelating reagents are used as effective collectors in wolframite flotation, and certain metal cations need to be added using chelating collectors so as to activate valuable minerals and obtain good flotation indexes. Different metal cations will result in different reactivity with collectors, in order to select the effective activator in BHA flotation of wolframite, the activation effectiveness of different metal cations on wolframite ((Fe,Mn)WO4) flotation were studied using pure minerals. The results showed that the wolframite activation by Pb2+was the best among the selected cations. The maximum flotation recovery of wolframite was found to be 95.58 % under conditions of 100mg/LBHA and 1×10-4mol/L of Pb2+at pH 9. The dosage of Pb2+needs to be controlled in an optimum range. Also, the activation mechanism of Pb2+ on BHA flotation of wolframite was investigated by measurements of contact angle, zeta potential, adsorption capacity and IR spectroscopy. It was found that Pb2+ could chemically adsorb onto the wolframite surface improving the flotability of wolframite and enhancing the adsorption of BHA on wolframite. When the dosages of BHA and Pb2+ were 100 mg/L and 1×10-4 mol/L, the adsorption quantity of BHA on wolframite sharply increased up to 0.30 mg/L at pH 9 compared with wolframite treated with only BHA.

Jan 1, 2014

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

It is well known that the crushing and grinding steps in the mineral processing of ores represent a substantial proportion of total energy, cost and carbon emission in mining. For instance a recent study calculated that 36% of the energy consumed by gold and copper producing mines in Australia was attributable to comminution (Ballantyne et al, 2012). Understanding this component of a business is essential in a world seeking to lower production costs, improve earnings and reduce its carbon footprint. The issue commands the attention and support of industry leaders in the mining sector, government, equipment manufacture, engineering design and research organizations. Furthermore, several researchers have often stated that globally, comminution processes consume between 3-4% of the world?s electrical energy production (Daniel and Lewis-Gray, 2011). In 2009-10, Australia?s Federal Government Energy Efficiency Opportunity (EEO) participants in the mining sector used 336.5 PJ, representing approximately 6 percent of Australia&apos;s total energy use. It is evident that the current practices of breaking rocks in tumbling mills are relatively inefficient (Fuerstenau and Abouzeid, 2002). Research and improved engineering design has established that a range of improved blasting, crushing and grinding techniques and flow sheets may lower project costs and carbon footprint. These include relatively simple process flow sheet strategies such as gangue rejection or pre-concentration prior to size reduction, a better combination of grinding technologies (both current and new systems), and selection of coarser grind sizes where ore and waste mineralogy allow. Yet, despite this systematic and detailed research, the industry remains somewhat reluctant to implement these strategies. CEEC (Coalition for Eco-Efficient Comminution) was established in 2011 to support knowledge sharing and change in an area of high-energy consumption for the global mineral industry. CEEC is a not-for-profit industry company, funded by grants from world wide industry companies, whose mission is to accelerate knowledge and technology transfer in the field of energy-efficient comminution. The key benefit to the mining sector arising from CEEC?s activities will be an increase in the rate at which more energy-efficient comminution data sets, processes, and technologies are developed, demonstrated, shared and applied. This will contribute directly to the industry?s target of reducing operating costs and carbon emissions. CEEC International Ltd and JKTech Pty Ltd teamed together to facilitate the inaugural CEEC Workshop, in June 2012. The purpose of the workshop was to produce a roadmap to provide guidelines for how (1) operations can achieve best EEC practice in the short to medium term, in collaboration with vendors, engineering companies and other service providers, and (2) what R&D is needed to achieve paradigm change in EEC in the medium to long term, e.g. 75% reduction in comminution energy in 10 years.

Sep 1, 2012

By P. N. Mohan Das, K. Harikrishna Bhat

"The major ilmenite reserves are located in India at Chavara (CH), Manavalakurichi ( MK) and Chatrapur, Orissa (OR). India stands first in terms of ilmenite reserves, which are estimated to be 278 million tonnes out of which, 142 million tonnes are processable. Mineralo-chemical analysis shows that Chavara ilmenite is the most weathered one with about 60% TiO2 while Chatrapur is the least weathered with about 50% TiO2. Co-existence of ilmenite with pseudorutile, rutile and haematite is observed in substantially varying amounts in the three deposits. It is observed that the tropical weathering rather than the source rock difference has apparently played an important role in imparting major compositional and structural dissimilarities among ilmenites in different places.In processing of ilmenite through the Becher process, aeration rusting of pre-reduced ilmenite is found to be the rate limiting step thus, affecting the productivity of the process. Investigations have proved that the addition of some organic compounds such as glyoxal, sucrose etc., to the system accelerates the reaction to such an extent that the rusting time has been reduced to less than half.A new route of processing ilmenite for synthetic rutile has also been developed in which, ilmenite is carbothermally reduced and then processed through plasma route. The slag thus obtained is processed further to get high-grade synthetic rutile, metallic iron and high purity iron oxide. The process has been scaled up in a continuous moving bed plasma reactor. It is technologically and economically more viable where, all the iron values are recovered as salable byproducts. This paper describes the salient features of the technologies developed for the beneficiation of ilmenite to synthetic rutile."

Jan 1, 2003

By E. Scheepers

Within a phosphorus producing submerged arc furnace it was found that the continuous fluctuation of the furnace between a flowrate-driven state (high throughput) and a thermodynamic-driven state (low throughput) caused both techniques to have similar overall, predictive abilities and resulted in a linear, ARX-type, adaptive prediction model as the model of choice. Secondly, this pre-diction model was developed, tested and then shown to have a reasonable, 8-hour-ahead predictive accuracy (R2, coefficient of determination) of 30% (±6%) on future Pslag values. This inherent relationship exists because, at the precise moment of a Pslag prediction, the furnace already contains the metallurgical memory (input variables to the linear model) needed to ensure that some predictive possibilities will always exists - all as a result of the long residence times in the furnace. Residence time, however, is not a directly adjustable variable but rather a fully dependent variable and a function of an array of interconnected and interactive variables. In fact, this applies to virtually all input variables, reemphasising the importance of innate metallurgical memory. Thirdly, predictive control possibilities were explored by simulating the set-points of two fully independent variables used by operators to control the process: the ratio of fixed carbon-to-P2O5 and the ratio of silica gravel-to-pellets. This linear, predictive control model showed only a slight improvement with an 8-hour-ahead predictive accuracy of 35% (±7%). This highlights how ineffective current adjustments are in optimally steering the process and how difficult even incremental improvements in feed-forward and predictive control can be. Finally, it is shown that fundamental design-, sampling- and process restrictions currently associated with the process will always limit the predictive and especially control accuracy or meaningfulness of any dynamic model. These restrictions include the size of the furnace resulting in long residence times, 8-hours sampling intervals, an extremely complex and interactive process and a 16% spatial analyses variation on the Pslag values ? the very value that the model is to predict. The point is made that, given the current status quo, even the perfect dynamic prediction model can not improve on an 8-hour-ahead prediction of 30% (±6%). This barrier can only be pierced with e.g. tidier and more frequent sampling regimes and other upfront capital investments, a decision that becomes a cost accounting exercise and that can only be taken by the management structure. An investment demanding ever-increasing attention is CFD software and it?s potential to shed more light on the complex interactions within the furnace.

Jan 1, 2014

By P. Pourghahramani

Several structural characteristics change during intensive milling such as chemical composition, phase transformation, crystallite size, lattice strain, lattice parameter (s) and solid reactivity etc. The creation of defects enhances the stored energy (enthalpy) in the solids and consequently causes a decrease of activation barrier for the process and/or subsequent processes. In this paper, the effects of milling on the structural changes of hematite have been investigated using dry millings. The structural changes have been characterized using a combination analysis of BET surface area measurements and X-ray diffraction (XRD) analysis. Besides, the hydrogen reduction behaviors and kinetics of mechanically activated samples and initial sample were studied using simultaneous thermal analysis (STA). The methods of Williamson-Hall and Warren-Averbach were used for analyzing of XRD patterns to resolve and extract the microstructural characteristics of hematite phases. It was concluded that the breakage and aggregation of particles take place mainly in the starting and prolonged stages of dry grinding, respectively. The BET surface area enlarged steadily over the grinding processes whatever milling methods were utilized. The characterization of structural changes revealed that the hematite milled under various conditions did not undergo any significant reaction or phase transformation during milling processes. In addition, X-ray amorphous phase con-tent increased gradually with extending the grinding intensity. The maximum X-ray amorphous phase exceeds about 81% after 9 hours of milling in both tumbling mill and vibratory mill. The Williamson-Hall plots revealed the anisotropic character of line broadening for deformed hematite and changes in the trend of microstructural characteristics as a function of milling time. It was found that the surface weighted crystallite size decreases and lattice strain increases over the grinding periods. The minimum surface weighted crystallites were calculated about 17.3 nm, 12.2 nm for the products of tumbling and vibratory mills respectively. The maximum lattice strain,, in the grinding with tumbling and vibratory mills was calculated about 4.44×10-3 and 3.95×10-3respectively. 21/210nmLe=<> The non-isothermal kinetic analysis of the products revealed that Fe 2O3 reduced to Fe in a two-step process via Fe3O4. Intensive grinding resulted in improved resolution of overlapping reduction events. It was also established that the mechanical activation had a positive effect on the first step of reduction. The prereduction step in the activated samples initiated and completed at lower temperatures than that in non-activated samples. The activation energy of reduction decreased at the first step of reaction with increasing the grinding intensity. Intensive milling increased slightly the average activation energy of the second step of reduction due to the present of finely agglomerated particles and intensive sintering of the particles in higher temperature ranges.

Jan 1, 2014

By O. Martinsson

The Kiruna area is an important mining province in northern Sweden, which is dominated by Fe- and Cu-Au deposits. Economically most important for the region, are the apatite iron ores with an annual production of c. 43 M ton of crude Fe-ore and a total production of more than 2000 M ton of ore the last 100 years. The apatite iron ores in the Kiruna area are dominated by either Magnetite or Haematite and contain varying amounts of apatite giving them a content of Fe and P, which varies between 30-70 % and 0.05-5 %, respectively. A typical geochemical feature of the ores is the strong enrichment of REE that is caused by a high content of REE in apatite and the occurrence of Allanite and Monazite containing 22.4 and 69.8 wt% REO, respectively. At Kiirunavaara, the content of REE in apatite varies between 0.07 to 1.57 wt% REO with a dominance for the light rare earths. The variation in REE-content of apatite depending on textural and paragenetic aspects is not known but apatite grains may display a strong LREE-depletion due to hydrothermal alteration. Monazite occurs as rod-shaped or tabular inclusions in apatite and is suggested, to have formed in response to hydrothermal alteration of apatite after the emplacement of the ore. Inclusions are mainly found in the central part of apatite grains occurring in veins and schliren, while they are rare in apatite occurring disseminated in the ore. Monazite also occurs as larger grains outside apatite and together with Allanite is found in texturally and paragenetically different settings within the ore. These occurrences of REE-minerals may largely be a product of LREE mobilized by alteration of apatite after the emplacement of the ore. However, REE-minerals including Allanite and Monazite might also have formed directly from late magmatic fluids. Keywords: apatite, monazite, allanite, ree, kiirunavaara, iron ore of kiruna type, mineral chemistry

Sep 1, 2012

By Sathyaprasad Nanjundaiah

The Paper intends to showcase a framework for spatial data collaboration from multiple sources of data, in order to create a single source of truth across the Organization. The framework is targeted to reduce the data duplicity, re-work, time loss due to search of required data and hindrances to fetch or transfer data from various data sources. The spatial data collaboration will provide a single window view of the entire organization with respect to its operations, management, sales, customers and competitors on a spatial reference across various regions in the World. Large Organizations with cross-country operations can standardize the use of spatial data through this framework for ease of data access, increasing the data reliability / integrity and better / on time decision making. Keywords: spatial data, GIS, collaboration, framework, mining, ESRI, tab files, shape files, ETL, reliability, integrity, interoperability, geo data, geo database, single source of truth

Sep 1, 2012

By Kunihiko Yamaguchi, Gjergj Dodbiba, Toyohisa Fujita

Usually magnetic separation is performed to separate ferromagnetic, paramagnetic and diamagnetic particles by controlling magnetic field strength. In this research the wet high gradient magnetic separation at various kinds of magnetization of medium has been investigated to separate different kinds of magnetization of paramagnetic mineral particles from each other. Most of week paramagnetic particles are captured at high magnetic field using superconducting magnet. If the magnetization of fluid is larger than that of paramagnetic particle, the paramagnetic particle cannot be captured in the direction of magnetic field. The paramagnetic particles of different magnetization such as hematite, chromium oxide, perovskite and rutile are separated in different magnetization of fluids. These particles are present in the incinerated bottom ash. The separation is useful to recover titanium oxide from bottom ash and the removal of chromium of bottom ash is important to reuse the bottom ash as cement. The used fluids are paramagnetic liquids dissolving paramagnetic salts and the water based magnetic fluid dispersing the stable ultrafine magnetite. The dispersion condition of particles related to zeta-potential of the suspension feed is also important to separate effectively by controlling pH

Jan 1, 2014

By Robin B. Batterham

"Since the 1970?s we have seen a marked corporate response in terms of the environment. In part this has come from regulation but it has largely come from stakeholders and the community. Rising expectations have in general been met. We now see a similar trend towards sustainability. At the same time, the importance of mining to the share market has decreased drastically and with that decrease has come the requirement for the mining sector to show returns similar in manner to other sectors. While rationalisation can achieve some progress towards these goals, the long-term requirement is for innovation, as it always has been. This paper looks to the logical goal of innovation within a sustainable mining framework and targets the removal of the desired metal values with minimal environmental footprint. It is suggested that broad ranging alliances will be necessary, particularly amongst the R&D suppliers, to achieve this goal. Industry will need to take an active role given the recent global restructuring.THE MARCH TO SUSTAINABILITYSince the 1970?s there has been an increasing corporate response on environmental matters. We have moved from matters environmental being issues relevant only to minority groups through a series of attitudinal changes by management. Whilst there have always been examples of excellent environmental performance, for many in the 70?s spending money on improving the environment beyond some minimal level was seen as a distraction from production or treated in a similar way to donations to the community. There is little of that attitude these days, as most mining companies have long since regarded the environment as a core business direction. Indeed, for some years one could note an escalation in matters of environmental reporting to the extent that the environmental performance of companies is now very public. In some cases, NGOs have even been invited to help certify and audit the reporting standards. Similarly with health & safety.There is now a rising expectation on the part of the community that social matters will also be given the same level of support as health, safety and the environment. This time around it would appear that the mining industry is at the leading edge of sustainability. The Global Mining Initiative (Global Mining, 2002) and the contributions to the Rio World Summit on Sustainable Development (Rio +10, 2002) suggest that sustainability is being taken very seriously by the mining industry. For sustainability it is convenient to use the Brundtland (1987) definition. This definition has widespread acceptance with governments, industry, environmental groups, financial institutions and individuals as a direction against which our activities and plans can be measured."

Jan 1, 2003

By R. Batterham

"The history of mineral processing is indeed long and has always been tied to mining methods of the day. While many new processes and devices have been developed, the most significant trend in recent times has been the ever increasing scale of operations. There is serious doubt this ongoing trend is enough to match the global trend of falling grades and rising energy demands needed for mineral processing. As well we see that globally, the social licence to operate for mining (and hence mineral processing) is far from secure. Indeed, some argue that mining as we know it is dying and in the future, mining will be much more environmentally secure, even to the extent of insisting upon “in place” recovery and only bringing to the surface the valued product. In this paper we comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 - 20 years but in the meantime, the focus is just as likely to be on removal of waste much earlier in circuits. Either way, mineral processing as we know it will change significantly. INTRODUCTION Mineral processing has a long history well covered in a recent publication (Habashi, 2006) who points out “the ancient Egyptians knew already that it would be easier to melt an earth rich in gold particles than another which is poor. As a result, all efforts were made to enrich the gold by washing away the light gangue minerals. Similarly, another ancient method for enriching gold particles from a river stream was by means of fleece, hence the Greek myth of the “golden fleece”. Since the middle ages, striving for improved economics has driven a string of innovative developments in milling and separation. The reader is again referred to the informative and illustrative text by Habashi."

Jan 1, 2018

By David G. Hulbert, Daniël J. Oosthuizen, Bernard Muller, Daniël de V. van der Spuy

"Expert Online is a software system that makes use of novel artificial intelligence technology, known as the Interpreting Expert System (IES), to mimic an informed expert on a minerals processing plant. Previous implementations of the IES were only capable of explaining the controller actions. Expert Online will also take on the more difficult task of explaining the complex process behaviour to the operator in simple language.The primary functions of Expert Online are to serve as a training tool and an online assistant to operators. However, it is also expected to be of value to supervisors and plant managers.A number of additional features are envisaged, including different operating modes, fault detection, speech synthesis and advanced message filtering. Expert Online will increase the operator’s knowledge of the process and his/her understanding and acceptance of the complex control systems. Users would be supplied with relevant and timeous information required to make informed decisions to ensure smooth plant operation.This paper discusses the structural design of Expert Online for implementation on the latest version of MINTEK’s open control platform, PlantStar, as well as several advances and additions since the previous implementations of the Interpreting Expert System."

Jan 1, 2003

By Venkataramana Runkana, Pradip Gautham, Beena Rai, Sreedhar Reddy

"IT enabled platforms are the key to provide an integrated view of the business activity or an enterprise as a whole. Attempts to integrate all functions in an enterprise such as mine-to-market initiatives, wherever and to whatever extent implemented, have provided significant benefits to the industry. The transformative potential of IT enabled integration platforms is illustrated in this communication from our own work in this field. TCS PREMAP (Platform for the Realization of Materials and Products) is a knowledge-driven engineering design and development platform which leverages modeling and simulation and artificial intelligence into the engineering design process. We illustrate the customization of this generic platform for the design and optimization of mineral processing plants in an integrated manner. TCS PEACOCK (Process and Equipment Analytics for Optimization and Control) has been developed to enable automation of data analytics in the operating plants. We illustrate its utility and power in improving the plant performance with the help of case studies from our work on pelletization of iron ores and optimization of flotation plants. INTRODUCTION We are living in an exciting digital era. With the advent of cloud computing and social media on the one hand and rapid advances being made in several research areas of interest to us in the minerals and metals industry such as artificial intelligence (AI) & machine learning, robotics, unmanned vehicles including drones, big data analytics, 3D printing, sensor technologies, renewable energies and internet of things (IoT), many disruptive transformations in our industry are on the horizon. Recent advances in information technology (IT) and knowledge engineering, in combination with appropriate domain expertise, that is, our enhanced understanding of the underlying science of mining and mineral processing operations and the availability of a variety of powerful modeling-simulation tools make it possible to address the challenging problems facing the mining and mineral processing industry, in an integrated manner."

Jan 1, 2018

By K. Price, G. Wang, L. R. Moore, Y. R. Xiong, J. Gu

"Sand is a naturally occurring granular material that is a result of the physical or chemical breakdown of rocks. Raw/natural sand contains various minerals, and it is this combination of minerals that brings the value to the construction aggregate industry. However, it is the quartz component of sand that is valued in its application as industrial silica in glass, high purity quartz, foundry sand, and oil and gas fracturing. Depending on the industry, the grade requirements can be the concentration of SiO2, particle size or shape, as well as contaminants such as the heavy refractory minerals, clays, fines, and alkali metals. With the ever declining mineral feed grade, processors continue to face challenges making the industry specific concentrate grade. As such, it becomes more important to tailor make the processing reagents to fit the mineral, processing conditions, and desired quality specification. This paper focuses on the application of novel collectors towards the beneficiation of sand for each of the major industrial silica applications. INTRODUCTIONQuartz is a mineral composed of a framework of silicon and oxygen atoms. It is the second most abundant mineral in the Earth’s continental crust. There are many species of quartz, which are defined by the particle size, shape, and color. Silica sand is one of those species, which is the byproduct of the physical or chemical breakdown of quartz containing rocks or crystals. Geologist define silica sand as a silica mineral with a particle size between 0.05 and 2 mm in diameter (Zdunczyk, 2001). Silica sand has significant value to society in recreation (beach sand and toy boxes), construction aggregate (concretes and asphalt), industry (iron & steel casting, fracturing proppants, and glass), as well as specialty products such as semiconductors or silicon wafers used in electronics.The aggregate business is the dominant consumer of silica sand products. Conversely, glass making, foundries (casting material), abrasives, and fracturing proppants are the dominant applications for industrial silica sand. Not much beneficiation is required for sand products going into the construction industry, other than sizing and scrubbing to remove clay. However, the industrial silica sand applications are dependent on particle size, shape, and degree of contaminants, which sets the market value (table 1). Therefore, as the more specialty products are produced, more sophisticated techniques and chemistry need to be applied to ensure the appropriate quality is met."

Jan 1, 2018

By S. Z. Shafaei

An experimental investigation has been carried out using a laboratory scale Denver flotation cell. For evaluation of cokeable coal of Alborze Sharghi coal washing plant, the full factorial method was used to statistically design and analyse the experiments. The 2 factorial interaction model were developed for combustible recovery and ash content as response and diesel dosage, conditioning time, feed percent solids and rotor speed as factors. Model validation and residual analysis were con-ducted and results indicated that the fitness, predictability power and residual distributions of models were good. The effect of parameters and interactions were examined and it has been demonstrated that rotor speed, solid percent and interaction between diesel dosage and solid percent were more important terms of all responses. A product with approximately 78% combustible recovery and 10% ash content was obtained at 4000gr/ton diesel fuel oil (high level), 30 sec conditioning time (low level), feed percent solids of 15% (low level) and 800 rpm rotor speed in appropriate condition.

Jan 1, 2014

By H. R. Zhang

In this paper two optional production processes are presented for reasonable utilization of primary sylvinite in Qinghai province, China. The two kinds of products as chlorine-free potash fertilizers; potassium sulphate or potassium magnesium sulphate can be obtained. In the course of potassium sulphate production, using primary sylvinite from Qinghai salt lake as raw material with impurities such as sodium chloride and insoluble in primary sylvinite, it must be prepared by flotation before being converted into potassium sulphate. This final product has found wide use in tobacco industry in China. However, in some cases Chinese farmers would rather buy the fertilizer of potassium magnesium sulphate than high quality of potassium sulphate. With flotation process which is a little different from above mentioned, the potassium magnesium sulphate fertilizer may be produced by washing one of the flotation concentrate presented as picromerite, while another concentrate containing potassium chloride is treated as by-product.

Jan 1, 2014