Search Documents

By Eric J. Foell

Recognizing that the planned commercial exploitation of polymetallic nodules in the deep sea should be accompanied by environmental studies in order to protect this largest and least understood ecosystem of our planet, the German Ministry for Research and Technology has since 1989 funded a longterm and large-scale disturbance-recolonization (DISCOL) experiment in the abyssal Peru Basin of the equatorial South Pacific Ocean. The circular study site is located at 4150m depths and encompasses about 10km2 of relatively flat, heavily sedimented sea floor with low (< 15%) nodule coverage near an existing German nodule mining exploration license area. The RV SONNE, a large and well-equipped multi-purpose research vessel, served as platform for all environmental cruises conducted to date. The initial DISCOL expedition (SO-61, Feb.-March 1989) was carried out in two legs. During DISCOL 1/1, a study site was selected, a pre-disturbance baseline assessment was undertaken, and sea floor disruption was begun using the "plow-harrow", a uniquely designed disturber device towed repeatedly across the circular study area. During DISCOL 1/2, disturber deployments continued until the device had created 78 criss-crossing and partially overlapping tracks along which nodules were essentially plowed under while sediment from up to 15cm below the seabed had been turned over and exposed at the surface. In addition to the obvious within disturber track impacts, sediment mobilized by plowing drifted off with the prevailing near-bottom current and redeposited downstream, blanketing nearby areas not directly disturbed. Immediately after the disturbance phase, an initial post-impact sampling series was performed. The DISCOL Experimental Area (DEA) was revisited about six months (DISCOL 2, SO-64, Sept. 1989), three years (DISCOL 3, SO-77, Feb. 1992), and seven years (ATESEPP SO-106, Jan.-March 1996) after disturbance to collect further post-impact samples, monitor changes in the benthic community and follow the recolonization process. In addition to benthic community studies, plankton investigations were initiated during the third DISCOL cruise (SO-77) and continued during three further cruises (SO-78, SO-79 and SO-80/2) in 1992.

Jan 1, 1996

By J. C. Wiltshire

Both ferromanganese crusts and nodules present potential processors with enormous volumes of tailings of dubious environmental character: most processing scenarios fail to utilize the uneconomic manganese itself, leaving a total waste volume on the order of 96% of the incoming ore. Each current disposal proposal seems flawed: (1) backhauling to the initial mine site is costly and might run afoul of EPA or UN marine dumping*regulations, (2) subsea disposal near a coastal processing site means almost inevitable community opposition, (3) agricultural soil amendment for improving barren lava or coral rubble appears to require prohibitive amounts of supplementary phosphate, and (4) the slag resulting from an energy intensive pyrometallurgical processing may have potential as road ballast, but few processors will opt for smelting in all but those locales where energy is very cheap. This unfortunately rules out a smelting operation in almost any Pacific Island environment. We envision at least one other scenario which could result in both the removal of tailings from a processing plant and an increase in the supply of useful building materials at little or no cost to either the processing or construction industries--transforming a tenacious waste into a novel resource. Ongoing experiments have demonstrated considerable potential for turning acid leach tailings into dark composite facing stone, fancy black tile, novelty ceramics or concrete aggregate. The tailings are commonly very fine grained and may also serve as an additive in drilling mud. Applications as an additive to asphalt also need to be explored. The metal scavenging nature of ferromanganese minerals should be considered as a radioactive waste disposal matrix. There is no doubt that the greatest challenge will be

Jan 1, 1991

By Delphine Pierre, Jean-Marie Augustin, Anne-Sophie Alix, Charline Guérin, Cecile Cathalot, Yves Fouquet, Arnaud Gaillot, Ewan Pelleter, Carla Scalabrin, Florian Besson

With the world’s growing demand for metals, seafloor massive sulfides (SMS) deposits are now seen as a possible mineral resource that could contributes to secure metal supply for human needs. SMS deposits are characterized by high concentrations of base metals and at some place high contents of precious and rare metals. Since 1977 and the discovery of the first high temperature (HT) hydrothermal vent and its sulfide mineralization and high biodiversity, more than 300 sites are known today. If the exploration strategy for detection of active hydrothermal sites is now robust, their associated mineralization will not (and must not) constitute a potential target for deep-sea mining due to environmental concerns and technical limitations. Recent studies on SMS deposits are rather focused on extinct and buried mineralized sites characterized by a lower biomass. Several geophysical techniques to explore and detect extinct SMS (eSMS) and buried SMS (bSMS) have been developed (e.g. Kawada and Kasaya, 2017; Szitkar et al., 2017, 2014) using different approaches (e.g. regional or local scale; ship-based or using underwater vehicles) with several degrees of success or limitation. Here we present results from acoustic surveys performed on the TAG hydrothermal district during the BICOSE (2014) and LEVE-SMF (2016) cruises and direct observation provided by HOV (Nautile) dives carried out during HERMINE cruise (2017). Acoustic data were acquired using two different multibeam echosounders (MBES): the hull-mounted Kongsberg EM122 (12 kHz, R/V L’Atalante) and the ROV-mounted RESON SeaBat 7125 (400 kHz, ROV Victor) (Figure 1). After processing, acoustic seafloor backscatter data from both MBES provides complementary qualitative results in relation to the seafloor composition. The analysis of the seafloor backscatter data obtained by near-seafloor surveys with the high-resolution 400 kHz MBES shows a clear relationship between low backscatter strength values and areas covered with pelagic and hydrothermal sediments whereas high backscatter strength values are associated to pillow lavas and basaltic scree. Intermediate backscatter strength values are rather related to old and younger eSMS as well as to mineralization on TAG active mound.

Jan 1, 2018

By James R. Hein

Manganese nodules from the Cook Islands (CI) Exclusive Economic Zone (EEZ) are compositionally different from other nodule fields. CI nodules have relatively high cobalt concentrations and low nickel, copper, and manganese concentrations (e.g. Hein and Petersen, 2013). This reflects the predominantly hydrogenetic (seawater source) origin for metals in the CI nodules versus dual seawater-pore water sources for most other nodules. The concentrations of many critical and strategic metals have not been previously analyzed for CI nodules, so comparisons with other nodule fields have been limited. To address this, we analyzed a set of nodules distributed throughout the CI EEZ for a complete set of 67 elements, including all of the metals that may be of economic interest, such as the rare earth elements (REEs), yttrium, tellurium, niobium, zirconium, tungsten, titanium, and others (see selected elements in Table 1). In addition, we recalculated the tonnages of nodules and contained metals from nodule abundance areas (in square kilometers) determined by GIS ArcMap calculations based on JICA/MMAJ (2001) nodule distributions. The nodule tonnage calculated and summed from each abundance sector yields a total inferred resource estimate of 9.66 billion tonnes of nodules covering an area of 1.21 million square kilometers; using a cut-off of 6 kilograms of nodules per square meter, yields a median tonnage of 8.59 billion tonnes of nodules covering 687,647 square kilometers (Table 2).

Sep 14, 2011

By Sven Petersen

In April 2010 three REMUS6000 series autonomous underwater vehicles (AUVs) have been used to simultaneously map large areas near the Mid-Atlantic Ridge (3°N) axis in water depths ranging from 1,000m to 4,000m. One vehicle was provided by the Leibniz-Institute for Marine Science, IFM-GEOMAR (Kiel, Germany) the other two were provided by the Waitt Institute for Discovery (La Jolla, USA) and managed by the Woods Hole Oceanographic Institute (USA). The REMUS6000 vehicles, manufactured by Hydroid Inc. (USA), are "cigar-shaped" vehicles (4m long and weighing approx. 900kg) and consist of a tapered forward section, a cylindrical midsection and a tapered tail section. An internal titanium strongback, which extends through much of the vehicle length, provides the structural integrity and acts as a mounting platform for syntactic foam, equipment housings, various sensors and release mechanisms. The AUVs can be used in various payload configurations such as multibeam bathymetry, electronic still camera, or subbottom profiler. For these missions the electronic still camera configurations was installed. An EDGETECH 2200M dual frequency (120/410 kHz) side scan sonar was used to map the seafloor, but other frequencies are readily available for more options in resolution and range. The 120 kHz side scan transmitter was used for most missions in order to map large areas (increased range) and to be able to fly at higher altitudes (between 70m and 90m) above the rough seabed encountered in this area. The maximum slant range was between 600m and 700m on both sides resulting in a swath width of up to 1.2 km. Line spacing ranged from nearly 1,000m in flat areas down to 400m in steep terrain. Side-scan mosaics were generated with a 1m resolution. Selected areas were targeted by the higher resolution 410 kHz transmitter as well as by bottom photographs flying as low as a few meters above the seabed. The vehicles navigated autonomously using a combination of inertial navigation (Kearfott T-24 or T-16 INS) and long baseline acoustic navigation by computing their range to two moored acoustic transponders. Working efficiently in this rough topography at speeds above 3 knots was only possible due to the obstacle avoidance capabilities of these AUVs.

Jan 1, 2011

By Tatiana ?. Sedysheva, Vladimir V. Ivanov, Michail E. Melnikov, Irina A. Pulyaeva

"INTRODUCTIONHydrogenetic Fe-Mn crusts are ubiquitous in the ocean basins and play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Directed research, which started in the last quarter of the 20th century, has provided significant results, with substantial amounts of data produced on Fe-Mn crusts structure, composition, and distribution in the global ocean [3, 4 - 8]. Now, commercial interests gain more and more attention. Mining systems are being developed which involve fragmentation of the crusts and their separation from the substrate. The effectiveness of such activities greatly depends on physico-mechanical characteristics of the crusts and rocks on which they form. This determines the importance of the engineering geological study of the objects.This article comprises the results of the engineering geological studies of the crusts samples (72 samples) and their underlying rock substrates (75 samples), which were carried out during the research cruises 6-06, 6-07, 6-08, 6-13 (2006-2013) on the Magellan Seamounts guyots in the Western part of the Pacific Ocean by the specialists of the State Scientific Centre Yuzhmorgeologia [10 - 13, 19, 20]. The authors of the article directly participated in the studies mentioned above.MethodsEngineering geological studies were carried out on board of the research vessel Gelendzhik and in the laboratories of NPA «Sevmorgeologiya». The studies involved the determination of the following parameters:"

Jan 1, 2017

By Jayne Holden

Development of a deep-sea mining system is a new and interesting field of research. Commercial mining of the ocean floor for SMS deposits is yet to occur, and while exploration of the undersea has been undertaken by various research institutes exploitation of SMS deposits is yet to be investigated in detail. Industry has been stimulated by the potential development of economically viable deep-sea mining methods. The establishment of deep-sea mining production has also been encouraged by industry trends. These include the success of the oil and offshore diamond industries, scientific advances in computer modeling, technological advances in undersea exploratory equipment and further development of the Law of the Sea. This project also presents an opportunity to build on UNSW?s established reputation, positioning the Mining Research Centre as a leader in this specialized field of research. This project aims to form a greater understanding of the environmental conditions associated with SMS deposits, detailing the physical, biological and chemical characteristics of typical ocean floor sites from an environmental management perspective. With the aid of previous numerical models and disturbance experiments that have been conducted at various ocean floor sites worldwide, new virtual reality models will be developed to enable assessment of the environmental impact of the undersea mining process. These models will simulate seafloor systems prior to mining through various stages including particle distribution and sediment disturbance, to illustrate the impact of a number of proposed mining techniques. The model will allow users an interactive virtual experience of a potential SMS deposit site where hotspots can be identified and mining processes can be demonstrated. This initial baseline model will help to establish generic parameters, which can then be modified and tailored to simulate a wide range of deposit sites and differing mining processes. These models will be validated with the development of appropriate physical modelling.

Jan 1, 2002

By T. E. Sedysheva

The study of Co-rich manganese crusts has reached the level which allows to start prospecting works in the observable future, and furthermore, probably, exploitation of ore deposits. In this connection, among other goals, the necessity to analyze a distribution of ore bed parameters in details is quite urgent. Foremost, these are crust thicknesses in connection with landforms and elements of submarine mountains relief. This report is based on representative sampling made in course of research cruises run by SSC Yuzhmorgeologiya over guyots of the Magellan Seamounts. Crustal covers could overlie seafloor surfaces which are confined to a various landforms and elements of relief under the condition, that they are free of sediments. These are planed parts of a summit surfaces, edges, spurs, rectilinear parts of slopes, intermountain saddles and volcanic edifices. It is known, that crustal thicknesses are different at a various forms of relief [1]. We processed statistically the data around crustal thicknesses, which were sampled by dredging and submersible drilling (Tables 1, 2).

Jan 1, 2010

By S. Kim Juniper

The discovery of chemosynthetic-based ecosystems at hydrothermal vents in the deep ocean was arguably one of the most important findings in biological science in the latter half of the 20th century. More than 100 vent fields have been documented along the 60,000 km global mid-ocean ridge system. Over 500 new animal species, over 80% of which are endemic to the vents, have been described from this environment. Unusual, highly evolved symbioses between invertebrates and chemolithautotrophic bacteria are common at vents, producing concentrations of biomass that rival the most productive ecosystems on Earth. Hydrothermal vents ecosystems, because of their very limited area and the presence of endemic species, are highly vulnerable to human disturbance. Mining for polymetallic sulphide deposits poses the greatest future physical threat to hydrothermal vents and their biological communities. However, there is more immediate concern about the impact of concentrated scientific research activities. Some sites have been revisited by several research expeditions per year for more than a decade. As vent sites become the focus of intensive, long-term research, oversight organizations are discussing mitigative measures to avoid significant loss of habitat or oversampling of populations. Canada recently became the first national jurisdiction to set aside a hydrothermal vent site as a Marine Protected Area.

Jan 1, 2001

By Charles L. Morgan

The Minerals Management Service of the U.S. Department of the Interior and the State of Hawaii Department of Planning and Economic Development are investigating the cobalt-rich ferromanganese oxide crust deposits found within the Exclusive Economic Zones (EEZ) of the Hawaiian Islands and Johnston Atoll. The objective of this investigation is to complete a preliminary resource assessment and an Environmental Impact Statement for potential leasing of mineral rights to these crusts. The results of this effort will be summarized and published in a Draft Environmental Impact Statement in March 1986. Three oceanographic cruises to deposit sites in the Hawaiian Islands EEZ were conducted by the University of Hawaii in 1984. As a result, data and sample analysis yielded the following resource estimates (in thousand tonnes): (1) total crusts - 378,500; (2) cobalt - 2,500; (3) manganese - 76,200; (4) iron - 59,700; and (5) nickel - 1,400. These estimates do not include key factors such as deposit continuity, recoverability, and environmental sensitivity. A preliminary attempt to quantify some of these factors for one particular deposit is in progress and will consist of detailed field studies followed by laboratory analysis. Similar evaluations of the Johnston Island EEZ have also begun and are based upon field work conducted by West German researchers and the U.S. Geological Survey. The Johnston Island EEZ appears to have crust resources about as large as those contained in the entire Hawaiian EEZ.

Jan 1, 1985

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5&apos;W, 45°56.5&apos;N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988

By Irina A. Pulyaeva

Hydrogenetic Fe-Mn crusts are ubiquitous in the ocean basins and play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Directed research, which started in the last quarter of the 20th century, has provided significant results, with substantial amounts of data produced on Fe-Mn crusts structure, composition, and distribution in the global ocean. Detailed study of several seamounts has given confidence about the scale of Fe-Mn crust development and their characteristics. Now, commercial interests gain more and more attention. However, at the same time some theoretical questions related to Fe-Mn crust history including controls on metal sources and concentrations have not yet been answered. Here, we present the overview of age, composition, distribution, and geological setting of hydrogenetic Fe-Mn crusts from Pacific and Atlantic seamounts and discuss the geological evolution and conditions that led to the formation of potentially economic concentrations of metals. The age, composition, and distribution of Fe-Mn crusts in the Atlantic and Pacific oceans were determined by using a Fe-Mn deposits database compiled from our original data, published papers, published databases, and other international sources. Comparative analysis of Fe-Mn deposits from the Atlantic and Pacific oceans shows that there are similarities in basic characteristics of crust formation in both oceans. Simultaneously, there are significant differences in the scale of Fe-Mn crust distribution and composition that can be explained by differences in geological settings and characteristics of the deposition environment.

Jan 1, 2011

By Wilfred Lus

Meaningful and real time environmental monitoring of marine tailings placement is a clear sign of deeper commitment to the people of PNG in regard to impacts of mining on coastal environment and marine life. Today daily mine wastes and tailings are increasingly being delivered to the seabed offshore of project sites in Misima and Lihir islands. Ramu and Simberi mining projects also plan to dispose tailings out at deep sea. As tailings leave the tailings pipe and come out into the seabed, concentrations of the cations and other potential harmful particles in the tailings stream need to be quantifiably monitored each day during the life of the refinery. For continuous monitoring of the tailing?s true chemical characteristics submarine cables connected with ocean floor observation systems consisting of deep-sea underwater video, and cation sensors and electrodes will be laid. Power transport to the tailings site and data transfer from the tailings site will be via opto-electric cables. Various data center instruments will record and manage the collected data. Observation data will be transferred in real time to stake holder?s data centers via a dedicated line from on-land stations, and then distributed to company offices and government establishments. Japan Marine Science and Technology Center, Telikom PNG, and Australian Institute of Marine Sciences will be the key advisers in this project. The main role of the observatories is to monitor and collect background seabed geochemical data prior to start of tailings disposal, during tailings disposal period, and after the life of the refinery.

Jan 1, 2001

By Patrick J. C. Ryall

Remotely control led drills capable of being lowered to the sea-floor from ordinary research vessels have been developed over the past two decades. These drills are currently being used in geological survey programmes on the continental shelves (Canada, Japan, Norway, United Kingdom) and for studies of mid-ocean ridges. Generally the drills fall into two categories: 1) those which are powered from the surface and controlled by an operator, and 2) those which are battery powered and follow an automatic programme. Some drills have a television camera mounted on them sending a picture to the surface as an aid to site selection and geological interpretation. Typically the drills are capable of drilling a core 2.5 - 5 cm diameter up to 10 m long. While most of these drills are designed for <1000 m depth, some can drill in water depths of as much as 3500 m.

Jan 1, 1985

By Derek Ellis

There are two environmental issues which have only recently begun to need planning in detail for marine mining. One is the environmental consequences of mine closure; the other is environmental terrorism. In principle it is not difficult to predict the pattern and rate of biodiversity recovery after mine closure on metalliferous depositional seabeds. 1-5 years to a self-sustaining community of organisms is a generalized guideline, depending on depth and particulate composition. The rate and pattern of biodiversity recovery on some metalliferous hard-rock habitats is far less predictable due to the patchiness and rareness of the habitat. Ecoterrorism at mines, whether on-land or marine, is now to be expected. A good example of resource industry ecoterrorism is the fire-bombing of logging and cement trucks in Oregon in 2001. But there have also been bombs at mine sites, as at Asbestos, Quebec. It is also possible to regard some resource-loss lawsuits as frivolous, hence forms of ecoharassment. Marine mining operations should take note of the development of environmental terrorism (and terrorism in general) and its various manifestations and impacts. Potentially these range from minor work stoppage inconveniences, to serious financial risk jeopardizing the economics of a mine, to jail for company executives, managers and environmental staff, and to harassment and killing of mine personnel.

Jan 1, 2005

By Willam R. Normark

During a series of dives with the submersible ALVIN in 1984, samples of massive sulfide were recovered from four vent sites. All sites occur within a linear, steep-walled cleft about 50 m wide and as much as 30 m deep. The cleft bisects the axial valley floor throughout the 15-km-long study area and appears to have been the source for the most recent volcanic eruptions in the valley. Three of the vent sites are defined by a set of discrete hydrothermal discharge zones; as many as eight have been identified over a distance of 500-800 m along the cleft floor. Sulfide deposits occur as individual and coalesced mounds, spires, and chimneys generally less than 3 m in height but a few might be as high as 10 m. The vents are also marked by extensive, yellow-to-amber ferruginous sediment and clots of bacterial matter. Some vents have extensive colonies of tube worms, gastropods, mollusks, and several predator species, such as crabs and squid. The fourth vent site has no visible discharge and consists mainly of "dead" spires and chimneys of massive sulfide. The massive sulfide samples collected with ALVIN are primarily sphalerite with minor marcasite, pyrite, pyrrhotite, isocubanite, chalcopyrite, wurtzite, and anhydrite. Bulk analyses of these chimney and spire samples show Zn contents approaching 60% by weight and significant enrichments in Ag and Cu. Vent fluids have the highest concentrations yet reported for Zn, Fe, and Mn. Thus, the Zn- and Ag-rich nature of massive sulfide from the southern Juan de Fuca Ridge study area

Jan 1, 1985

By Grigori Abramov

As we enter into the 21st Century, miners are looking more attentively at new mining technologies allowing decrease environment damage along with operational cost. This technic would allow developing of poor and difficult mineral deposits, including the World Ocean offshore zone. Borehole Mining is an underground/underwater remote method of mining carried out from floating platforms or vessels. Definition of Borehole Mining (BHM), working schematic, main technical data and its advantages are given. The method is currently in use in mining of different type of raw materials, such as: uranium, iron ore, quartz sand, coal, polymetallic ores, phosphate, gold, diamonds, rare earths, amber and more. It is also in use in oil and gas stimulation, salt domes storages building and environmental problems solution. Recently recorded data of Borehole Mining productivity (80-100 t/hour/hole) and a depth of mining (over 1 km) has been achieved in a last couple years. Remoteness of method not only secures complete safety of operations but also allows wide sector of underwater applications. The World leaders in Borehole Mining are Russia and the United States. Based on previous experience the Universal Tool for Seabed Borehole Mining has been developed for wide sector of usage: from exploration and mining - through oil & gas stimulation to souterrain storages construction and lake&apos;s bottom cleaning.

Jan 1, 2000

By Francois P. Leroy

In the quest of studying the assigned blocks of seafloor for deep water mining, each member country of the ISA is thirsty for accurate information as to the level of resources available. Manganese nodules represent a large portion of the resources and are as precious as they are hard to locate and harvest. Resolving such challenges is what drives the technology development and yields instruments and products capable of serving this field of research. This presentation will study how manufactures of oceanographic instruments have pushed the technology envelop to in order to transform a collection of sensors and instruments into a seamless and adapted assembly working to serve the researcher and prospector in the challenging field they operate. Deep water data collection is characterized by the following challenges: ? Deployment, recovery and handling of the vehicle ? Producing high resolution at great distances ? Positioning that data with accuracy to relocate Teledyne Marine will present the work performed in its engineering laboratories to produce sub systems and systems now capable of delivering key information necessary to the proper cataloguing and exploitation of deep water mineral mining. Understanding and controlling the alternative resources available to each country will allow better management of current traditional land based minerals.

Jan 1, 2010

By Burrows D. R.

Metal-rich sediments precipitating from hot saline brine pools were first discovered in 1965 in the Red Sea.1-2 The subsequent discovery of high temperature black smokers and associated massive sulphides in 1977 at latitude 21oN on the East Pacific Rise3 came more as a confirmation than a revelation. Formation of massive sulphides through precipitation from circulating sea-water had been predicted by Oftedahl in 19584, and the mechanisms well evaluated in basaltic-hosted Cyprus-type 5 and in Kuroko-type deposits.6,7 Sea-floor exploration from 1977 through the 1980?s in sediment-starved mid-oceanic ridge (MOR) settings had little impact on land-based exploration. This is primarily because: a) MOR spreading centres were recognized as poor analogies to even Cyprus-type basalt-hosted deposits; b) their preservation potential was limited due to rapid oxidation and c) the metallic deposits studied were small and therefore not directly comparable to the far larger ore bodies on land. More recently underwater mineral deposit research has focused in a variety of back-arc environments associated with felsic submarine volcanism, environments more similar to those predicted for the formation of Kuroko-type deposits (e.g. Okinawa Trough, 8 Lau Basin, 9 Manus Basin, 10 Aeolian arc, 11). Most studies, while scientifically interesting, were hampered, in general, by a lack of good descriptive data, a reliance on isolated grab samples, and a lack of sub-surface observations. This research has therefore had only limited direct impact on exploration strategies with the possible exception of research conducted in areas where faulting provided enhanced vertical exposures. 12

Jan 1, 2011

By Jun Lu

Compared with land mineral resources investigation, as well known, it is more important for marine geologists to get image data (e.g. photographs, video tapes and various charts) because they are often hard to reach deep seabed directly. In the past years a plenty of image data which are in various forms have been accumulated. In contrast with both digital and character data managing the image data by using database is just unfolding and it will be a trend for marine mineral resources investigation. GIS (Geography Information System) offers another useful means of processing image data, especially geological data. GIS is characterized by processing vector data (e.g. point, line and polygon), but newer versions of GIS software package are also able to process raster data (e.g. photographs etc.). The present author made a presentation on marine mineral image database during 25th UMI, but that system runs under DOS environment and dealt with only mineralogy. Recently a new system which integrates Oracle image database with GIS (ArcView version 3.1) has been developed. This system runs under Windows NT environment. In the network environment Server/Client mode is adopted, and over 200 basic subdatabases (tables)are located on Server; operating interfaces are located on several clients so that several persons can operate the system simultaneously. The whole system involves five types of marine mineral resources: manganese nodules, cobalt-rich crusts, polymetallic sulfides, phosphorites and gas hydrates. The data of every type of marine mineral resources described above are distributed among five units and several blocks. The units and blocks are described below:

Jan 1, 2000