Search Documents

By Tetsuo Yamazaki

Natural methane hydrate has been scientifically studied as a global carbon reservoir. However, in Japan, it?s potential as an energy resource has been industrially highlighted, because there are few domestic oil and natural gas resources in Japan, but many potential deposition areas for methane hydrate in the sea around Japan. Less CO2 discharge from methane compared with coal, oil and conventional natural gas for the same calorie value is considered an advantage for its use as an energy resource. Because methane hydrate is distributed at shallow depth in sediments on the ocean floor, accidental leakage of methane may occur while we utilize methane hydrate. Methane itself has a considerable impact on the greenhouse effect, if it reaches the atmosphere. Therefore, it is necessary to estimate its behavior in the environment after leakage if we want to use methane hydrate as energy resource. The mass balance after leakage of methane on the seafloor and in the water column can be studied through the analyses of natural cold seepages and hydrothermal activity.

Jan 1, 2004

By Toru Yamasaki

A concept of plate-tectonic controls for the formation of seafloor massive sulfide (SMS) deposits in back-arc settings was established by Franklin et al. (2005). According to Franklin et al. (2005), a consequence of extension and rifting is subsidence, thinning of the crust, and the rise of hot, athenospheric mantle into the base of the crust. Underplating of the crust by mafic magmas results in low-pressure partial melting of the hydrated crust at a <15-km depth, and the generation of felsic anhydrous melts. The rapid ascent of hot felsic melts, along with mantle-derived mafic melts, results in bimodal volcanism that characterizes rift and volcanogenic massive sulfide deposits (VMS) environments. The rapid and focused advection of the magmatic heat within the rift to the near-surface environment which are required to sustain vigorous long-lived VMS hydrothermal systems. Faults within rift environments may also allow seawater to penetrate into subvolcanic intrusions and mix with magmatically generated metalliferous fluid or allow a direct magmatic contribution from shallow crustal level (3–12 km) magma chambers (Franklin et al., 2005, and references therein). In addition, the caldera-forming processes are favorable for the formation of VMS deposits and the focused high heat flow and cross- stratal structural permeability that is restricted in time and space to caldera development provides an explanation for the clustering of VMS deposits and their restriction to specific time-stratigraphic intervals and structures in the evolution of submarine central volcanic complexes (Franklin et al., 2005, and references therein). The concept is persuasive, although it is based on a series of logically constructed reviews mainly focused on ancient on-land deposits.

Jan 1, 2018

By Se-Won Chang

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese nodules on the Campbell Drift, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. During the research voyage SAA3 by R/V Tangaroa (TAN 9909) in July-August 1999, seafloor sampling and camera towing were conducted along the two transects across the known flow path of the Deep Western Boundary Current (DWBC) perpendicular to the lowermost margin of the Campbell Plateau and Bollons Seamount. The four major nodule facies, SHH (slope hydrogenetic nodules with high density), AHH (abyssal hydrogenetic nodules with high density), ADH (abyssal diagenetic nodules with high density), and ADL (abyssal diagenetic nodules with low density) were identified. Two additional minor nodule facies, SIB (slope irregular nodules with ice-rafted boulders) and SHB (slope hydrogenetic nodules with boulders and crust), of localized distributions are also identified.

Jan 1, 2003

By Valery M. Yubko

During the last ten years seven applications for nodule-bearing areas of the World Ocean Floor International Region (IR) have been made by national companies of Russia (Yuzhmorgeologiya), France (IFREMER/AFERNOD), Japan (DORD), India (The State Department of Sea Resources Development), China (COMRA), Korea (KORDI) and the Interokeanmetal Joint Organization (IOM) of some East European countries and have been registered by the Preparatory Commission of the United Nations International Seabed Authority (ISA). Besides these groups registered within Resolution 11 of the Final Act of the III United Nations Conference on the Law of the Sea there are four international consortia registered in the USA [Kennecott (KCON), Ocean Mining Associates (DMA), Ocean Management Incorporated (OMI), and Ocean Minerals Company (OMCO)], which have interest in areas in the IR and can be considered as potential applicants. All registered areas (with the exception of the Indian Ocean) including the areas of potential applicants and also 6 areas, reserved for the ISA are located in the Clarion-Clipperton Zone of the Pacific Ocean. If within each area not less than one deposit of polymetallic nodule-bearing ores can be discovered, then, the total number of such deposits, for the present moment, is 20.

Jan 1, 1994

By James C. Barker

Concern over the availability of domestic critical and strategic mineral supplies has led the Bureau of Mines to evaluate the reserve development potential of alternative sources in Alaska. Near the village of Platinum, on the southwest Alaska coast, the Red Mountain concentrically zoned ultramafic complex is a source of onshore alluvial placers containing platinum-group-metals (PGM). It has long been suggested that valuable placers may also underlie the shallow coastal waters of the Bering Sea. A direct correlation of placer PGM and chromium to ultramafic rocks in the area was studied by the Bureau and the extent of the complex was mapped. Magnetometer and gravity data and geological studies suggest the complex is a large lensoidal body trending several kilometers offshore to the southwest with a probable steep southeasterly dip. Multiple Pleistocene glaciations and marine transgressions have eroded the western and southwestern portion of the complex. Sediments containing PGM, chromium, and associated gold (largely derived from glacial till) have been transported northward along the advancing coastline by littoral currents. Beyond the breaker zone, these sediments are generally buried by recently winnowed sand and gravel transported by strong longshore tidal currents. There is also evidence that paleoplacer channels underlie the marine sediments.

Jan 1, 1986

By Randolph A. Koski

Recent investigations located at least six major massive sulfide deposits (dimensions measured in tens to hundreds of meters) within a 50-km-long segment of Escanaba Trough, the sediment-covered axial valley of southern Gorda Ridge. The sediment fill is intercalated silt and sand turbidites and hemipelagic mud with a maximum thickness of 500 m. Several volcanic edifices, spaced at approximately 15-km intervals along the ridge axis, penetrate and locally breach the sediment. The largest sulfide deposits form mounds and ridges on the steep flanks of structurally unstable sediment-capped blocks that have been uplifted above the volcanic edifices; both sediment and sulfide deposits are undergoing rapid erosion and redeposition. Although hydrothermal activity appears to be absent at most sulfide fields, 220°C fluids are discharging from the tops of sulfide mounds near 41°00&apos;N lat, 127°31&apos;W long. Recent pillow lavas and sheetflows erupted onto the sediment-covered sea floor less than 500 m away from the active vent field. The massive sulfide deposits have compositional characteristics that differ from deposits formed on sediment-free spreading axes. The Escanaba Trough deposits include Fe- and Cu-rich, Zn- and Pb-poor massive sulfide mounds, polymetal (Zn-Fe-Pb-Cu-As-Ag-Sb-Sn) sulfide vent structures, abundant barite-rich chimneys, crusts, and sinter cones, and thermogenic petroleum in the sulfide and sediment. Sulfate-rich crusts have high Au values ranging between 2 and 10 ppm. The unusual mineral assemblage at Escanaba Trough

Jan 1, 1989

By Maria Baker, Kristina Gjerde, Lisa Levin, Verena Tunnicliffe, Lenaick Menot, Rachel Boschen

Deep-sea mining is rapidly approaching the test-mining phase to prepare for commercial mining in multiple oceans, both in areas within and beyond national jurisdiction. The first test-mining operations are likely to focus on seafloor massive sulfides found at active and inactive hydrothermal vents within national jurisdictions – possibly in the coming months. Beyond national jurisdictions, the International Seabed Authority (ISA) is developing the regulations to oversee exploitation of polymetallic nodules, massive sulfides and cobalt crusts. The Deep Ocean Stewardship Initiative (DOSI) minerals working group has, over the last 3 years, made formal submissions on the regulatory framework, on the draft exploitation regulations, on the article 154 review of ISA and on the initial environmental regulations. In advance of both test and commercial mining, we urgently need to identify and develop comprehensive, ecosystem-based management practices for deep-ocean environments subject to mineral extraction. Transparent criteria for deep-sea institutional and corporate social responsibility also need to be established. Proactive development of management practices, frameworks and policy prior to the onset of mining will facilitate some degree of protection and preservation of the marine environment, whilst enabling the use of seabed mineral resources. The DOSI minerals working group constitutes a broad spectrum of scientific, industry, legal and policy expertise. We provide expert opinion, both in collated and individual response forms, on deep-sea mining related concerns to ISA and national bodies. Our publications and workshops on key concepts raise awareness and provide scientific updates on ecosystems targeted for mining. See http://www.dosiproject. org minerals working group and join us to further this work.

Jan 1, 2017

By Hunsoo Choi, Sung Rock Lee, Ian J. Graham, Ian C. Wright

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese modules in the Campbell Nodule Field, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. The petrography, chemistry, inferred genesis, and 10Be/9Be dating of the nodules were described in the science report of GNS (Chang et al., 2003a, 2003b; Graham et al., 2003a) and presented at UMI (Chang et al., 2003c; Graham et al., 2003b). The morphology and distribution of ferromanganese nodules were also published in detail (Wright et al., 2005). This presentation is only concentrated on the mineralogy and chemistry of the nodules.

Aug 24, 2006

By William Siapno

Manganese nodules, as metal ores, have for the most part been cast aside from further consideration within this century. However, in the decade of the 90s, rising demand at all levels of society, for clean air give nodules a new - lease on life as a stack gas cleaning agent. Further, the Clean Air act of 1990, mandates enormous outlays to bring systems into compliance with new stringent standards. Quick corrective actions are imperative. Research beginning in the 1960s proved nodules possess unique qualities to remove acid compounds from stack gases. Early this year, the National Science Foundation awarded General Electric an $83 million contract to design a system to extract oxides of sulfur and nitrogen from coal fired power plants. Environmental damage is abundantly evident on the ground, from the air as well as form space. A dirty pall of yellow-brown smog is smothering both animal as well as plant life around the globe. Losses run into billions!

Jan 1, 1991

By Yuta Yamamoto

Seafloor massive sulfides (SMS) which contain Au, Ag, Cu, Zn, and Pb have been interested in as a target of commercial mining these 15 years. Japan has large potential of SMS and a national R&D project for the mining has been active these 5 years. However, the economy of SMS mining is very bad, because the waste tailing disposal cost is very expensive in Japan. A slurry flushing method is experimentally examined in this study for the improvement of the economy. During the flushing, because of density difference between the metal-rich ore and the waste rock, a kind of gravity separation is possible. The results suggest a possibility of the actual application.

Sep 14, 2011

By Michael J. Cruickshank

The University of Hawaii, Ocean Basins Division (OBD) shares, equally with the University of Mississippi, Continental Shelf Division (CSD), congressional funding for the Marine Minerals Technology Center, a Generic Minerals Center under the U.S. Department of the Interior&apos;s Mineral Institutes Program. The State of Hawaii supports the program by the provision of salaries for the Executive and Technical Directors and by the provision of fiscal, administrative, and facilities support through the Hawaii Natural Energy Institute, the Research Corporation of the University of Hawaii, and the School of Ocean and Earth Science and Technology. The Center&apos;s program of research, technology development and education is multi-disciplinary and international in scope. Activities since the MMTC/OBD was established in June 1988 have included: Research projects * Development of a Free-Fall Seafloor Hard Substrate Corer. * The Microtopography of Manganese Crust deposits. * Evaluation of the Cobalt Crust Continuum on Seamounts in the Hawaiian Exclusive Economic Zone. * Graphite Furnace Atomic Absorption Spectrometer. * Computer Aided Design Methodology for Power, Communication and Strength Umbilicals. * Characterization and Environmental Impact Assessment of Tropical * Reef-derived sands for Beach Replenishment.

Jan 1, 1991

By Peter E. Halbach, Andreas Jahn

"Co-rich ferromanganese crust deposits exist on slopes, summits and platforms of seamounts and guyots throughout the global oceans, where deep-sea currents have kept the seafloor structures more or less free of sediment for millions of years. They form by direct precipitation from cold seawater under more or less oxic conditions and consist of thin layers (2 up to 25 cm thick) covering hard substrate rocks in water depths of 800 to 5000m (Halbach and Marbler, 2009; Hein et al., 2000). Besides Mn these crusts contain interesting concentrations of minor elements (Co, Ni, Ti and Cu) and trace elements (Mo, W, Te, Ga, Pt and REEs), thus they represent significant metal deposits and promise potentially valuable additions to the world’s metal resources.The prospects for mining of this marine type of metal deposits largely depend on the grades and the scale of the potential ore resources. However, only a few percent of existing seamounts and guyots have been mapped and sampled in detail, most of them in the Pacific Ocean. Therefore, a model to estimate the geological resources based on the global seamount catalogue of Wessel (2001; revised: Wessel et al., 2009) and the empirical parameters which control the metal composition and distribution was developed."

Jan 1, 2017

By J. R. Woolsey

The cost of an offshore exploration project is mainly dependent on the size of the vessel engaged for the work and increases dramatically with increasing size. Of the various factors influencing vessel size, the type and size of the sampling equipment is typically the principal consideration. This scenario is particularly true of shallow sampling programs employing a vibracore system. The problem develops when certain bottom materials such as densely packed fine sand require sampling. This type of material being one of the most difficult for the standard vibracore systems, with integral core liner, to penetrate to a reasonable depth of some five to seven meters. The problem is mainly related to the excessive cross sectional area of the cutting bit required to accommodate the core liner. The typical solution has been to apply more power to the vibracore drive head which results in a considerable scale-up for the entire system with attendant increase in vessel size. In order to reduce operating cost, M.M.R.I. has developed several systems for deployment from vessels in the 20 meter range. Two systems are modifications to the basic vibracore and a third is a vibralift system. Basically, one of the vibracore units is employed where core liners are required, utilizing a special jet bit designed to reduce the cutting pressure on the bit while not affecting the integrity of the core. The other designed for core extrusion on

Jan 1, 1986

By Richard H. T. Garnett

Large scale, profitable, offshore mining of cassiterite started in 1907 around the coast of south Thailand and continues today in Indonesia. The more complex marine mining of diamonds commenced in the early 1960?s and is now an established industry off the coast of Namibia in southern Africa. The activities have involved many diverse organisations, and have required the development of new marine mining equipment. De Beers Marine, more recently as contractor to Namdeb, has been the dominant producer since 1989. Smaller, public, mining companies, registered in South Africa, Canada and the U.K., have achieved mixed performance results, but the total annual revenue from offshore diamonds now exceeds about US$ 180 M. With the benefit of hindsight, there are some useful lessons to be learned from the experiences. Mining of placer deposits at sea is more difficult and more costly than on land. It justifiably commences in response to a market demand for a product that cannot be supplied in sufficient quantity from onshore sources, not because the marine resource exists. The high costs can be offset in places by submarine grades so high that they have not been seen on land for a century. Technical and commercial success requires a combination, and a sufficiency, of ore reserves, capital, experienced people, and technology. Economic viability is not achieved easily and some diamond mining companies have experienced a very short productive life, terminating in their acquisition or liquidation. The reasons for failure in marine mining, regardless of whether the product is diamonds, gold, or tin, invariably are similar and fall into two categories. Those outside a company?s control include the sea conditions, taxation and fiscal climate, security of lease tenure, and the diamond market. The others, assignable to the company, provide important instructions for those who may aspire to advance the cause of marine mining.

Jan 1, 2004

By S. Jeffress Williams

The topic area for this paper covers the United States portion of the northern Gulf of Mexico, extending from the Rio Grande delta east to the Florida peninsula. Declaration of an Exclusive Economic Zone in 1983 expanded Federal economic jurisdiction on the continental margins from 12 to 200 nautical miles seaward from the coast. The nation-wide area of the EEZ totals 3 million square nautical miles, with approximately 186 thousand square nautical miles in the Gulf of Mexico. In the Gulf, the continental shelf has an area of 81 thousand square nautical miles, extending to a depth of 600 ft. and having widths of 6 to 120 nautical miles. Specific areas on the shelf offer the greatest potential for containing aggregate and other hard mineral resources. The primary geomorphic features along the Gulf coast include: barrier islands, chenier plains, tidal inlets, bays and lagoons, estuaries, and deltaic headlands. These features are composed of terrigenous siliclastic sediments, except for the west Florida coast, south of 29°N latitude, which is dominated by carbonate sediments. On the shelf, the primary features are linear sand shoals and associated sand sheets, relict delta lobes and channels, and banks related to salt diapirs and coral reefs. The composition and distribution of sediments in these coastal and shelf features are determined by numerous geologic factors including: seabed topography; riverine sediment discharge; sediment dispersal patterns due to currents, waves, storms and tides; tectonics and subsidence; and repeated fluctuations in sea level.

Jan 1, 1986

By W. D. Siapno

Marine mineral resources have been reviewed in great detail on numerous occasions over the past few years. A summary of these efforts would indicate there is little new on the horizon as far as economic programs are concerned. Deep ocean minerals, though not forgotten, hold little promise for development in the immediate future, i. e., manganese nodules, cobalt crusts, polymetallic sulfides, etc. Nearer to shore, within the EEZ, and particularly within waters under state control greater industrial interest is expressed. Interest in sand and gravel not only persists but is growing, dependent largely upon the construction industry. Precious metals demonstrate the greatest growth potential.

Jan 1, 1988

By William D. Siapno

The International Marine Minerals Society has now come of age! Previously known as the International Marine Mining Society, it was an informal group without officers, by-laws or official status. Despite the lack of formal structure, the Society has cosponsored symposia both in Europe and in North America including the 16th Annual Underwater Mining Institute in Halifax, Nova Scotia, last year. The roster of members is now sufficient to emerge as a fledgling professional society. To this end an ad hoc committee was appointed to prepare by-laws stating the objectives of the Society, provide the procedures for the election of officers and other guidelines essential for the operation of the organization. This paper briefly summarizes the history of the group, the by-laws, together with membership requirements.

Jan 1, 1986

By Naoki Hiroyoshi, Kunihiro Hori, Kengo Sekimura, Mayumi Ito, Kouki Kashiwaya, Eiji Yamaguchi, Masami Tsunekawa

Cobalt-rich ferromanganese crusts and nodules ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei. During the mining operation, these rocks should be separated as unfavorable waste rocks with the manganese minerals. The ferromanganese crust and nodule ores require mineral processing to remove the substrate rock before the smelting. Deep-sea manganese nodule ores in contrast contain vanishingly small rocks, and can be directly treated with a smelting process without mineral processing treatment. This paper shows phisical and chemical description of the ores for the purpose of mineral processing, and reports liberation degree measurements of crushed ores and gravity separation tests. A mineral processing treatment flow is proposed from the obtained results. There is the first report of applying gravity separation in the treatment of coarse sized crushed products of cobalt-rich ferromanganese crust and nodules ore.

By Chris Castle

The Chatham Rise is a submarine topographic feature lying off the east coast of New Zealand between the South Island and the Chatham Islands and within New Zealand?s jurisdiction. The Chatham Rise hosts economically significant deposits of rock phosphate and other potentially valuable minerals. The deposits comprise nodules lying on, or just below the surface of the seabed in shallow waters. Rock phosphate is an essential ingredient of fertilizer and can be applied directly to pasture. There is a realistic opportunity the phosphate deposits could supply New Zealand?s agricultural requirements for an estimated 30-year period at current rates of consumption.

Jan 1, 2011

By P. U. W. Appel

Despite the very large offshore Exclusive Economic Zone (EEZ) area of Greenland (in excess of 2 mill. km2) virtually no work has been carried out on marine minerals on the ocean floor. Apart from a single reconnaissance survey by a mining company, major activities have been those of oil companies exploring the West Greenland shelf in the early seventies. The West Greenland shelf and its extensions is the most obvious area for year-around accessability when looking for marine mineral deposits. So far, only one onshore placer deposit has been found - ilmenite deposit near Thule, NW Greenland, whereas a gold placer in South Greenland presently is being evaluated.

Jan 1, 1988