Search Documents

By Drew M. Kurtz, Jeff L. Rai, Sara F. Frailey, Mohammad Ayub Iqbal

"This paper presents the foundation changes made for a five-span bridge over the Lehigh River constructed as a design-build project. During excavation within the cofferdam at Pier 2 for the construction of a spread footing to bear on rock, it proved extremely difficult to control the water entering the excavation as the sheet pile tips were variable due to the bedrock pinnacles and a weathered rock zone above the top of rock allowing water to pass below the sheeting. Water also entered from the bottom of the excavation, possibly due to the presence of solution openings within the dolomite bedrock. After repeated failures to achieve subgrade elevation and maintain a dry excavation, a design change to drilled shafts was made. Additional borings were performed for each of the shaft locations to explore the area underlain by karstic dolomite rock. A seal consisting of tremie concrete with adequate weight was placed to counter the differential head of water and the three drilled shafts (with minimum 25 feet [7.62 meter] rock sockets) were installed. A detailed construction sequence was followed and advanced quality control testing was performed. The construction of Pier 2 was completed successfully.1. INTRODUCTIONThis paper presents the description of the design change made from spread footing to drilled shafts as a result of site conditions encountered during the excavation for the spread footing for a bridge pier in the Lehigh River in Allentown, Pennsylvania. The bridge is located in an area underlain with dolomite rock, presenting karstic conditions including irregular top of rock and solution openings that provided high hydraulic conductivity below the top of rock. Also, the presence of a zone of weathered rock and pinnacle rock prevented the advancement of sheet piles when constructing the cofferdam. Thus, the difficulties of advancing the excavation to the desired spread footing level resulted in the design change to drilled shafts during construction. Since the project was Design-Build, the design could be changed by a collaborative process through the efforts of the Contractor, its geotechnical and structural engineers, and the State's (owner's) geotechnical and structural engineers and construction management staff."

Jan 1, 2016

By Anupam Saxena

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading test, and installation of piles for a 22-story condominium tower in southwest Florida, U.S.A. ASC was commissioned to provide value engineering services in the proper selection of an economical and satisfactory foundation system. For the site-specific subsoil conditions, various types of foundations were considered and following an evaluation of high structural loads, site-specific constraints, and the production timeframe mandated by the project owner, a prestressed concrete pile-supported system was selected as an economical and effective foundation approach. The building foundations were designed for a compression capacity of 575 kN (65 tons) for the tower and 220 kN (25 tons) for the parking structure. The axial pile capacity and lengths were predicted using SPT91 software. The validation of these capacities was derived from driving 21 probe piles and performing static loading tests on selected probe piles (2 in compression and 1 in tension). The predicted pile capacities were evaluated with results from static loading tests on selected probe piles. This information was effectively utilized as part of an overall quality control program to install a total of over 920 prestressed concrete piles to lengths ranging from 11.5 to 16.5 m (37 to 54 ft) below existing ground elevation as part of the foundation support system.

Jan 1, 1996

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By Axel J. Pollak

Since the late 1960's the Interstate Division for Baltimore City (IDBC) has been planning and developing the Interstate Highway System for the city to meet regional planning goals. The principal goals are to provide convenient access to the central business district and the port while diverting through traffic away from these congested areas. Interstate Route 95, an eight-lane highway carrying north-south traffic, has headed the city's priority list; during the 1970's its construction proceeded steadily from both east and west towards the harbor. Closing the final 8800-ft (2670-m) gap under the harbor will complete Interstate 95's construction. This final portion, known as the Ft. McHenry Tunnel project, will be built in nine construction contracts. Construction costs of the complete project are expected to exceed $700 million, making it the costliest single project in the Interstate Highway System. Full funding is being provided initially by the Federal Highway Administration (FHWA), and the Maryland Department of Transportation will re-pay the 10 percent local share from toll receipts within the first three years of operation.

Jan 1, 1989

By Shigetoyo Yasui, Masahiro Saitou, Nobushige Yasuoka, Keisuke Tsujimoto

"The Dry Jet Mixing (DJM) Method was developed and has been put to practical use on the initiative of the Public Works Research Institute and Japan Construction Method and Machinery Research Institute. This method is used to inject powdery binder with compressed air into soft ground while mixing the binder with the soil using the mixing blade to reduce the moisture content of the ground and cause chemical reactions between the soil and binder, thereby strengthening the ground and stabilizing its quality.Recently, there is a demand for high-quality, high-accuracy execution control.This paper introduces the New DJM Execution Control System, developed to meet the future demand for more sophisticated ground improvement, based on the past results of the conventional system in order to provide new automated execution control with improved accuracy, functionality and column quantity.1. INTRODUCTIONIn association with the densification of cities and the improvement of the social overhead capital, the underground space in urban areas is tangled with various underground structures including transportation facilities such as subways and underground roads, buried pipe such as water supply and sewerage systems,gas, electric power and communications lines, and underground malls.In addition, a lot of aboveground structures such as office and residential buildings, elevated tracks, expressways, embankment tracks are also supported with underground foundations.Tokyo, Osaka, Nagoya and many other large cities in Japan grow on plains spread along the coast or rivers. Waterfront flat areas which are very convenient for human activities, however, are often on the alluvial soft ground, where soft cohesive soil with a high moisture content, loose sandy soil, etc. are accumulated in a thick formation, with a high groundwater level.The DJM Method introduced here is used to decrease the moisture content of the soft ground, strengthen the ground and stabilize the soil quality by injecting powdery binder into the ground with compressed air, while mixing the binder with the soil using the mixing blade.2. OUTLINE OF DJM METHODThe DJM Method is used to inject powdery binder with compressed air into soft ground, while mixing the binder with the soil using the mixing blade, to cause chemical reactions between the soil and binder, thereby decreasing the moisture content of the ground and strengthen and stabilize the ground."

Jan 1, 2015

By Riad Diab

In 2018 the Caisse de Dépôt et Placement du Québec (CDPQ) awarded a $6.3 billion (U.S. dollars) design-build contract to the Joint Venture (JV) team NouvLR for the design and construction of one of the largest automated transportation systems in the world, called the Réseau express métropolitain (REM). The REM project is a 67 km (41.6 mi) light rail system with 26 stations linking downtown, the airport and the greater Montreal area in Canada. Out of the 67 km (41.6 mi) network, over 25 km (15.5 mi) is being constructed on a 650- span elevated structure founded on single drilled shafts socketed into rock. Optimizing the design of the drilled shafts was one of the main objectives of the geotechnical team, as it would likely result in shorter shafts that help significantly reduce the project costs. As part of the optimization process, three static axial load tests and two fully instrumented lateral load tests were performed, during the preliminary design phase, on sacrificial shafts to simulate the ultimate load level and validate construction procedures.

May 1, 2022

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Gust Van Lysebetten, Monika de Vos

The objectives of monitoring geotechnical structures can be very diverse, including optimisation of the design, quality control, long term performance assessment, and approval of innovative execution techniques. In this context, new measurement techniques, based on optical fibres, offer the possibility of accurate strain and temperature monitoring with very small sensors and limited numbers of cables. This paper briefly presents optical fibre sensing techniques and illustrates their application to geotechnical structures by means of some projects, carried out by the Belgian Building Research Institute (BBRI).

May 1, 2022

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Alexander Filotti, Richard Kalson

"1. INTRODUCTION- WHAT IS P3 OR PPP ?The Public Private Partnership (PPP or 3P) is a project delivery scheme based on the government providing land and/or a concession agreement, and on a private entity providing the design, construction, financing, operation and maintenance of the project for an extensive duration of time (up to thirty years). At the end of the operation-maintenance period, the project is turned over to the public entity, which fully owns the project at all times. While there are many PPP delivery schemes used around the world, for the present paper, we are going to analyze the impact of the Design-Build-Finance-Operate-Maintain (DBFOM) scheme on the deep foundation specialty subcontractor. There are couple of reasons that the PPP delivery system started to be used and implemented not only by developed nations (e.g. United Kingdom, USA etc.), but also by the International Development Bank for delivering major infrastructure projects in developing nations. From the point of view of government agencies, some of the reasons to use PPP are the following:??The primary use of private capital in an era where borrowing and/or supplemental taxation represents too much of a political risk. Budget deficits and taxation limits are extremely hot topics in every election (national or local) and the level of education of the electorate in this area is making it more and more difficult for politicians to use borrowed funds and additional taxation finance sources for public projects. At the same time, we see an increase in the social expenditures of the government in parallel with a needed increase in expenditures on infrastructure due to aging and neglect.??Bundling the construction risks with the operational and maintenance risks naturally pushes the private entity to increase the level of innovation and communications in the primary phase ( the construction phase) in order to develop future process based upon the innovation and communications utilized in the operation and maintenance phase of the project. This is true if contractual incentives are properly structured because “all revolves around incentives. In a world of ‘incomplete’ contracts, where it is difficult to foresee and contract about uncertain future events, it is important to get the incentive structure right” (Grimsey and Lewis, 2004).??The transfer of very expensive risks such as differing site conditions, schedule, design, construction, maintenance and operation costs from the public authority to the private entity.??The timespan of development and construction of a PPP project is usually shorter than the traditional procurement process (e.g. “ the I-595 P3 provided capacity improvements fifteen years sooner than a conventional plan would have offered. In Maryland, an innovative expansion of the Seagirt Marine Terminal in the Port of Baltimore was completed two years ahead of schedule due to the P3 model. As a result, the Port of Baltimore is only the second port on the US East Coast to have unrestricted access to both a fully functioning 50-foot channel and 50-foot berth.”)"

Jan 1, 2017

By Yazen Khasawneh, Yao Zhang

Upgrading and maintenance programs were proposed at a power generating plant in Indiana. To perform construction activities associated with the proposed upgrading and maintenance, a LR11350 crawler crane with a dead load of 1,500 ton was required in the vicinity of existing plant structures. The contact pressure from the crane tracks for the heaviest lift, maximum reach and angle (worst loading condition) were estimated by the rigging engineer to be on the order of 84 psi. Several concerns were raised regarding the total and differential settlements while the crane is in operation and the induced stresses on existing underground utilities due to crane loads. Three-dimensional finite element simulations were conducted using hardening soil model for the subsurface soils and elastic model for the other structural elements (underground utilities and crane mats) to optimize the configuration of the proposed crane foundation. It was found 1-foot thick engineered steel mats underlain by a 1.5-foot thick crushed stone pad will provide enough support to the crane. It will also control the settlement to the allowable limit and maintain the stresses in the underground utilities within tolerance. INTRODUCTION A LR11350 heavy lift crawler crane was proposed as part of an upgrade program at an existing power plant in the state of Indiana. The proposed crane will be sitting on an open ground in the vicinity of existing plant facilities, with multiple underground utilities going beneath the proposed footprint of the new crane pad. The existing utilities are of diverse kinds, including sanitary sewer corrugated metal pipes, electrical conduits and variable steel water/oil drain pipes. The safety and functionality of these underground utilities are critical to maintain the proper operation of the power plant. Therefore, the design of the new crane pad foundation system is of essential to control the ground settlement and the imposed stresses to the existing utilities (Davie et al., 1998, Scott 2017). To ensure all utility locations and depths are identified, the proposed footprint was thoroughly surveyed. Information in regard to each identified utility was provided by the owner. Subsurface explorations were conducted using geotechnical soil borings and soundings to evaluate the ground conditions and generate soil profiles. Numerical simulation and analysis utilizing finite element method were performed to design the crane pad foundation system and evaluate the responses of the utilities. This paper summarizes project information, geotechnical conditions and then focuses on the finite element analysis in assisting the design of crane pad and the utilities evaluation.

Jan 1, 2019

By Larry Rayburn

Augercast piles evolved in the late forties from the process of pressure grouting open holes backfilled with stone. In 1956, a patent was issued for a cast in situ pile by pumping high pressure grout through hollow-stem, continuous flight auger as the auger is gradually withdrawn from the ground. The patent rights expired in 1973 and the use of auger-cast piles greatly expanded with most large deep foundation contractors now installing augercast piles. At one time augercast piles had a bad reputation, partly because of not having a blow count to give some engineers a confidence factor and there were some quality issues. Over the years the quality issues have been eliminated and I am sure the augercast is the most installed pile in private industry and is now being used by some State Agencies.

Jan 1, 2005

By Greg Plutko

Laboratory testing has shown that the Marsh Funnel test can be significantly impacted by long-chain polymer entanglement. In general, shorter hydration time leads to more chain entanglement which in-turn, leads to higher marsh funnel values that values seen for longer mixing. This trend makes it very difficult to predict funnel-viscosity on successive days. Data is presented which helps to explain this chain interaction effect on Marsh Funnel data and how it differs from traditional Fann viscosity. The data suggest that this long-chain polymer entanglement occurs more in samples with less hydration time and decreases as hydration time increases. There is also suggestion that higher polymer concentrations have a greater drop-off in marsh funnel viscosity for a given aging length than do lower solids slurries. Fann rheology was shown to be much less impacted by the hydration time of the PHPA polymers than was Marsh Funnel viscosity. This suggests that the Marsh Funnel viscosity is impacted by some aspect of the slurry that does not affect Fann rheology as strongly. It is known from literature that longer-chained polymers have more potential to entangle and our data support the theory that the Marsh funnel viscosity is greatly impacted by this polymer-chain ‘roping’ entanglement.

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.