Search Documents

By Jochen Franke, Matt Bird, Thoma Perkins, Malcolm Powell, Jason Robertson, Paul Toor

zThe operation of SAG mills is variable over time due to their continually changing liner shape, mass and subsequent load motion. However, this tends to be poorly accommodated in liner design and mill control, with only limited compensation made for this influence, usually in the first few weeks after a new liner is installed. With ever-increasing ore competency, increasing energy costs and decreasing ore grades, simplified design and operational approaches that compromise the achievable mill efficiency are no longer adequate. This paper presents a methodology that has been developed to measure and account for the changes in mill performance as the liner wears. This involves monitoring all liner profiles – in other words the three-dimensional liner shape - over the life of the liner, then conducting controlled surveys at different stages of the liner wear life, and correlating the mill performance to the liner profiles. The measured liner mass is modelled to provide an ongoing meaningful load mass measure that excludes the liner mass.

Jan 1, 2012

By Irvine J. Berscheid

This paper describes a rock drill bit which, although conventional in the processes of manufacture and use on the job, has incorporated into the outer wall or periphery of the insert, where wear is always the greatest, a variable amount of extra metal, distributed in units of height of insert to withstand this excessive wear. Explained are variations of construction, how the extra metal enables the bit to drill more footage, prevent antitaper and the need to gauge grind, increase penetration rate and the length of run per regrind, reduce shank breakage and ma-chine costs, and permit increased production per man-shift, without requiring any change in equipment already on the job. F OR purposes of clarity, reference to bits here means integral rods or multi-winged bits which have their inserts sharpened to a conventional shape. When dull, the insert has worn, on its face, a flat which increases in width as we progress from near the center of the bit toward the outer edge. Very

Jan 1, 1965

By J. R. Shore, F. G. M. Gillett, E. J. Zickar

"The addition of fines to rod mill feed has been employed at Inco Metals' Frood-Stobie Mill since 1973. The fines, which act as a ""lubricant"", causes an increase in the pulp fluidity and assists the flow of feed through the rod mill. Fines addition was one of the main factors which led to improved rod mill performance and the elimination of rod mill tangles.This paper outlines the testwork performed in evaluating the addition of fines, and summarizes the beneficial effects on rod mill grinding efficiency, throughput rates, power consumption and noise level. INTRODUCTIONFrood-Stobie Mill is situated within the Frood-Stobie mining complex, on the southern rim of the Sudbury Basin. The Mill commenced operations in November, 1967, and has since processed in excess of sixty-five million tons of ore. Minus 8-inch ore is delivered to the Mill's coarse ore bin by two surface conveyor belts from the Frood and Stobie Mines, while Little Stobie ore is transferred by underground conveyor and hoisted directly into the coarse ore bin a long with additional Stobie Mine ore."

Jan 1, 1981

By R. K. Jonas

Many leading copper and other mineral processors have rapidly adopted advanced controls in last 5-10 years. Almost 600 multivariable predictive controls have been installed in mineral processing, and almost 50% of those are in copper concentrator plants. In most cases, mineral processors rely on 3rd party support to implement these advanced technologies. One challenge facing advanced control user is the selection providers and services for these technologies. The trend has been towards the use of multivariable predictive control and use of technology provider’s services. This paper will discuss status of advanced control, and the merging trends in the mining industry. A review will be presented of how advanced control is being applied in the mining industry over the last decade, and how user challenges are being overcome. Next the emerging uses of multivariable predictive control (such as multi/inter-unit optimization), focusing on the latest trends in concentrator plants. Finally, a review will be made of emerging technology advances in the that can be advantageous to mineral processors. INTRODUCTION Review of advanced control in mineral processing Advanced controls are serving an increasing role to improve processing plant operations and profitability. As advanced control is being installed into more mining processing plants such as copper concentrators, many of these plants are concerned about the selection technologies and vendors to support the installation and maintenance of these controls. In a study by Jonas and Craw (2011), they found that most new users have not had prior experience with advanced controls. It is the author’s experience of almost 30 years in advanced controls that most mineral processers considering advanced controls can benefit from better understanding of the technologies and their support requirements.

Jan 1, 2019

By T. G. Joseph, R. K. Soni, M. Curley

"Rapid dampening suspension is a proposed suspension design for ultra-class haulers that is intended to avoid metal-to-metal contact inside a strut and under shock loading, thus improving ride quality and ameliorating fatigue loading issues on a hauler structure. Laboratory testing has shown the ability of the proposed design to reduce the opportunity for bottoming out, that is, metal-to-metal contact between the colliding ends of oleo-pneumatic, two-piece suspension struts during the compression cycle. This paper predicts the performance of a full-size rapid dampening suspension strut by applying scaling rules to test the proposed design based on a set of field data from a Caterpillar 797B ultra-class haul truck operating in the oil sands region of the province of Alberta, Canada. The predicted performance of the suspension strut is compared to that of the original equipment manufacturer model, which was monitored on board the truck during field data collection. ¦ KEYWORDS Haul truck, Original equipment manufacturer (OEM), Rapid dampening, Strut, Suspension RÉSUMÉ La suspension à amortissement rapide est une conception de suspension proposée pour des camions de transport de catégorie ultra-class (des engins dont la charge utile dépasse les 320 tonnes métriques), visant à empêcher un contact métal sur métal à l’intérieur d’une jambe de suspension et dans des conditions de choc au chargement. Elle améliore la qualité du roulement et les problèmes de charge de fatigue sur la structure d’un camion de transport. Les essais en laboratoire ont confirmé que la concep¬tion proposée évitera au cylindre interne de heurter le cylindre externe, autrement dit empêchera le contact métal sur métal des jambes de suspension oléopneumatique en deux parties pendant le cycle de compres¬sion. Cet article prévoit la performance d’une jambe de suspension à amortissement rapide à taille réelle en appliquant les lois d’échelle afin de mettre à l’essai la conception proposée, sur la base d’une série de données de terrain relatives à un camion de transport 797B de catégorie ultra-class de Caterpillar (aujourd’hui remplacé par le nouveau modèle 797F) utilisé dans la région des sables bitumineux de la pro¬vince de l’Alberta, Canada. On compare la performance prévue de la jambe de suspension à celle du modèle du fabricant d’équipement d’origine (FEO), qui a été contrôlée à bord du tombereau pendant la collecte des données de terrain. ¦ MOTS CLÉS amortissement rapide, camion de transport, fabricant d’équipement d’origine (FEO), jambe de suspension, suspensionINTRODUCTION Research basis for the paper This paper is based on the unpublished MSc thesis work of El-Sayed (2003), Santos (2007), and Soni (2009) under the direction of Dr. Tim Joseph within the oil sands–equipment interactions program (OsEIP). OsEIP is part of the Alberta equipment–ground interactions syndicate (AEGIS) surface mining research group, School of Mining and Petroleum Engineering, University of Alberta. The aforementioned work spanned a decade of progressive studies into rapid dampening suspension systems, leading to the scale performance indications highlighted here. Although this paper uses a specific Caterpillar 797B suspension strut for field monitoring and as a basis for scale prediction of a modified rapid dampening suspension strut design, the design scaling principles used here could be applicable to any such design change consideration for an oleo-pneumatic suspension system."

Jan 1, 2019

By MacKenzie Dickson

"INTRODUCTIONGold is found in many natural states, native nuggets, loose grain in river sands, veins in rock, as well as associated with sulphides, oxides, etc., disseminated more or less minutely.Its high value in recent years has spawned new technologies to win values from sources once considered too lean for commercial recovery. Cyanide leaching from fine milled ore or tailings, from upstream recovery operations, coupled with adsorption onto relatively coarse granules of activated carbon, concentrate the gold enough to be converted to bullion by time-honoured methods.The carbon granules are fragile. Size degradation in handling must be minimized not only to prevent loss of gold on fine fragments of carbon that could pass with the barren tailings, but to maintain adsorption efficiency. Besides, the granulated carbon itself is costly. Circular Vibroscreens are winning acceptance for dewatering carbon granules thanks to their gentle yet effective performance in gold recovery systems around the world. The system at Equity Silver is illustrative.BackgroundEquity Silver Mines Ltd., Houston, British Columbia, first began production in September 1980. In 1984, a feasibility study showed that additional gold and silver could be economically recovered through cyanide leaching of the flotation tailing.Although the carbon-in-pulp (ClP) or carbon-in-leach (CIL) process is commonly used for extracting precious metals from slurries, the use of circular vibrating screens, and Vibroscreens in particular, for the carbon circuit is an innovation that cuts costs.Rectangular vibrating screens have been the conventional separation mechanism of choice across North America. In contrast, the use of Vibroscreens has been proven to be less costly for the initial purchase and installation. Also, these circular vibrating screens require less power and less space. A description of Equity Silver Mines' process shows how these screens have been successfully integrated into the system."

Jan 1, 1989

By V. Schenk

Dust exposure resulting from the exploitation and winning of natural resources below ground has presented a serious health problem since the beginning of mining. The boom phase of the German hard coal mining industry after World War II with at times up to 500,000 employees saw an increase of dust exposure of miners below ground as the mechanization of road heading and mining increased significantly. More and more miners were diagnosed with coal-workers-pneumoconiosis (CWP), a chronic and irreversible lung disease resulting in a significant impairment of pulmonary function. This realization led to a reduction of CWP in the German hard coal mining industry in the 1960s. The successful fight against CWP began with the introduction of technical dust prevention measures. By infusing the coal seam with water before mining, sprinkling and spraying of heading and mining machines as well as canopies with water, aspiration in places with high amounts of dust and the suppression of dust with chemical substances it is possible to significantly reduce the miners? dust exposure. All operating points below ground are checked and measured regularly with regard to dust exposure. Through the combination of these values together with the individual shift data a relatively precise profile of individual dust exposure can be obtained. This profile allows the targeted work assignment when certain predetermined limits have been reached, moving the miner to a work place with less dust exposure and thus reducing the chronic dust exposure. The state of health of the individual is known because since about 60 years ago extensive occupational health checks have been carried out regularly at least every two years which means that work restrictions can be imposed depending on the findings. Since the beginning of the 1980s more value has been attached to not only situational but also behavioral prevention. Given the comprehensive provision of protective masks, having a protective effect as well as the required comfort when being worn, each miner has the opportunity to protect his respiratory organs depending on the specific dust exposure. Through a combination of all these measures the German hard coal mining industry has succeeded in beating the classic coal miner?s disease CWP. For mines in the Ruhr valley this means that a miner who started work after 1978 will no longer develop CWP.

Aug 1, 2013

By J. G. Schofield, R. C. Francki, K. M. Donaldson, F. E. Ham

"Developments in pyrometallurgical technology have led to larger furnaces operating under more intense process conditions. In order to maintain the reliability of these furnaces, which are frequently single-line units, the design of the refractories, cooling systems and bindings has become more critical. Traditional thermal and chemical requirements for the refractory to resist slag attack must still be carefully determined. The larger, modem furnaces have placed a new emphasis on the structural properties of the refractories as well as their thermal properties to suit the extensive cooling systems. Based on operating experience, supported by computer models, the refractories and bindings are designed to work together to accommodate the thermal expansions and contractions in order to minimize permanent furnace growth and the risks of leaks. IntroductionElectric furnaces are used extensively in smelting copper and nickel ores and concentrates. Laterite nickel ores and high-magnesia copper, nickel and platinum sulphide concentrates are smelted virtually exclusively in electric furnaces to accommodate the high melting point of the slags produced. Although a number of smelting processes using oxygen-enriched and/or preheated air have been developed to replace reverberatory furnace smelting of conventional copper and copper-nickel concentrates, (lnco, Noranda, Outokumpu, Mitsubishi) electric matte furnaces remain a strong process alternative for these concentrates, either as the primary smelting vessel or for cleaning the slags produced from these processes.The development of large, high-powered furnaces has been an important factor in the growth of electric smelting technology, as evidenced by the list of operating matte and ferronickel furnaces shown in Table I. Because the compressive forces required to maintain a tight, leak-free furnace increase with furnace dimensions, the selection and design of the furnace refractories, cooling systems and bindings require increased attention."

Jan 1, 1993

By D. Lessard, S. Nantel

"Surface crown pillars are important Canadian,mining structures. Mines operating in the Canadian Shield usually have several, forming a first line of protection from surface elements.Detailed technical information from twenty-four Canadian hard rock mines show that the deposits dip steeply and are generally either single or multiple veins. Considerable overburden usually cap the deposits. The rock mass is often altered and intersected by important discontinuities.The designs for these types of pillars lack basic data and are based on experience rather than a scientific approach. Regardless of the competence of the rock mass, the surface crown-pillar thickness to width ratios (an unscientific design tool used by the industry) are usually less than five. Rock bolting is, in almost every case, used as a support measure. However, there are many openings neither backfilled nor monitored.The characteristics of openings with surface crown pillars are also examined."

Jan 1, 1988

By J F. Short

The jet piercing process, developed by Union Carbide Canada Ltd., is well established in blasthole production in open-pit mining. By this process, holes can be drilled, shaped and chambered for blasting. In suitable ore or rock formations, a considerable cost reduction can be achieved. This paper reviews the equipment used, relates how cost savings may be accomplished, and concludes with a mention of the most recent developments in this field. JET piercing and chambering, a process for blasthole production in open-pit mining, leads, in many instances, to improved drilling and blasting techniques and costs. It is a method of working rock with a supersonic flame and, to be most effective, depends upon a characteristic of the rock called spallability. Spalling, in this case, is the breaking away of surface particles from the rock body due to stresses caused by the thermal shock of the jet flame. Various rock properties contribute to this action, but, in general, the harder the rock the greater the spallability and the more effective and economical is the jet process. The jet process has the capability to drill, ream, shape and chamber holes for blasting.

Jan 1, 1965

By Rae Simpson

"This paper provides insight into the elements of computerized maintenance systems and identifies some of the factors which influence their effectiveness. The paper describes what to expect in terms of benefits and problems, the nature of effective computerized maintenance systems, some of the systems available and a process for selecting a system for your organization.The paper will be of interest to mining company executives and maintenance or computer personnel who are involved with, or contemplating, the introduction of computerized maintenance systems.IntroductionIn the drive to improve profits in an increasingly competitive world, mining companies are now using some of the most sophisticated equipment available. The introduction of large and complex equipment such as drag lines, haul trucks, and high-capacity milling equipment has resulted in order-of magnitude improvements in productivity. However, this productivity is now, more than ever, dependent on the continued operation of the equipment. A prolonged breakdown of a critical component can have a significant effect on companies' bottom-line results. As more technologically sophisticated equipment is introduced, maintenance costs become an increasingly important factor for mining companies.Fortunately, sound modern management principles are being used more often in maintenance departments. Progressive maintenance managers are turning to computers to help manage the myriad of details associated with running a maintenance organization.Some maintenance departments in larger mining operations would find it difficult, if not impossible, to operate at current productivity levels without their computer systems. Unfortunately, some other companies gain very little from their computerized systems and would probably be better off without them.How can you be sure that computerized maintenance will improve the maintenance picture for your company? What benefits can you expect to achieve? How do you go about selecting a maintenance system for your organization? These are some of the questions facing industry managers and executives today. In the following sections, we will provide some guidelines and insights to help address these challenges."

Jan 1, 1988

By Christopher R. Davis

Resource modelling is the basis for any economic appraisal of a mining project and includes a number of steps from data acquisition and validation to resource reporting and classification. At each step in the modelling process it is necessary to define the specific objectives, the methodology proposed to achieve those objectives and to establish a set of checks and validation tools to assess the effectiveness of the proposed methodology. The data used has to be both reliable and relevant for the purpose of the modelling. QA/QC for database validation requires verification of sample location; including correct collar location, topographic modelling and down-hole surveying. Validation is also performed on assaying information such as checks for sampling bias and accuracy of core splits, proper use of pulp duplicates and standards, handling of calculated values, explicit/implicit absent data and data entry errors. The second step involves identifying the mineralized domains resulting from the mineralization process. This step requires a geometric interpretation of all relevant geological features that have influenced the spatial distribution of the mineralization including dykes, faults and alteration. In addition, a geologic reference system rather than a standard Cartesian system is established to measure distances between samples. Once the mineralized domains are established and the database has been validated, statistical and spatial description of the mineralized samples are examined in order to establish the histogram and the variogram of all variables of interest and their correlation. Results are also used to calibrate the global resource estimate within the mineralized domain and to establish the search strategy for grade interpolation. The mineral envelope is filled with polyhedral cells representing mining blocks. The average grade of these blocks is estimated using kriging techniques in order to eliminate global bias and to minimize the local error in the block grade estimate. Visual checks are made to validate the spatial trends in grade distribution while global bias and smoothing effect are assessed from the declustered sample statistics. When required, smoothing correction may be applied using ?change of support? techniques. Simulations are used to perform sensitivity analysis and the simulation models are used if severe smoothing of spatial variability makes the interpolated model inappropriate for mine planning. The keys to successful resource estimation are an integrated team of geologists, geophysicists, geostatisticians and mine engineers using the best available technology and reviews by independent auditors. The resource team is also responsible for performing a QA/QC program in order to measure the effectiveness of the methods in meeting the specific objectives at each step of the modelling process.

May 1, 2001

By A. B. Luz, A. Middea

Kaolin clay is heavily used in the paper industry as a coating and a filler, however to attend the specifications required by the industry it has to be processed. Kaolin is also used as a filler and pigment in various materials, such as paint, plastic, rubber etc. Some crude kaolins as mined in Northern Brazil, contain colored impurities such as iron oxide and rutile/anatase. These minerals normally are stained by iron and as a result vary from yellow to dark brown in color. The kaolin beneficiation process used in that region consists mainly of degritting, fractionation by centrifuge, high gradient magnetic separation, bleaching with sodium dithionite, filtering and drying. In some kaolin clays from that region, titanium oxide mineral occurs in fine fraction, lower than 2 µm, and so making the industrial process more difficult. The conventional method of classification and bleaching with sodium dithionite, markedly improves kaolin brightness, but has little effect on anatase removal. In fact, the fine fractions resulting from centrifugation, in many cases contain more TiO2 minerals than the original whole clay or the coarse fraction. The present work is related to purification of Brasilian kaolin clay using selective flocculation for removing its colored impurities such as rutile and anatase. This study was conducted in bench scale and it consisted of: blunging, screening, conditioning and decantation. Overflow and underflow resulting from settling of the flocculated material were then dried and submitted to TiO2 and brightness analyses. Sodium polyacrylate and sodium silicate were added to kaolin clay suspension as dispersant and ammonium hydroxide was also added to adjust pH. After degritting, the minus 44 µm fraction was conditioned with hydroxamate surfactant and then polymers of different anionic charge were added. The influence of pH and type of polymer on efficiency of TiO2 removal, as well as kaolin mass recovery were studied. The results obtained in the present study are quite promising. It was possible to diminish TiO2 content and increase kaolin brightness (ISO) from 82 to 88%.

Jan 1, 2004

By T. Crivits, I. Bellemans, V. Cnockaert, K. Verbeken

It is well known that slag foaming can significantly complicate copper smelting processes. This is especially true for unpredictable events that generate large amounts of slag foam during a small period of time. These events are here referred to as eruptions and are typical for certain types of liquid bath furnaces such as modern top submerged lance (TSL) furnaces. A few authors already made the link between over- oxidation of the slag phase and slag foaming. In this work, the mechanism is studied in more detail and explained using the smelter chemistry and the behaviour of dynamic foam formation. Finally, the most influential parameters on the foaming behaviour of the process are presented. INTRODUCTION Copper remains one of the most important metals used in our modern society. In 2017, the annual amount of copper produced worldwide was about 23.5 million metric tons. This makes copper the third most produced metal in the world after steel and aluminium. The majority of this copper was produced by copper smelting, about 19 million metric tons, both from primary concentrate and secondary feed material as reported in ICSG’s World Copper Factbook 2018. In the past, copper smelting was mainly performed using Flash smelting, a technology developed before 1949 (Kojo, Jokilaakso & Hanniala, 2000). Nowadays, this type of smelter is being complemented by other smelter types such as ISASMELT and Ausmelt technologies. These are two types op smelter furnaces, based on the concept of a top submerged lance (TSL) furnace. These two technologies were both commercialized around 1990 (Arthur & Hunt, 2005). It is estimated by Wang et al. (2016) that at this time, both flash and TSL smelters contribute equally to the total amount of annually smelted copper. Flash smelting stays the most important technology for extracting copper from primary sources. TSL furnaces, on the other hand, are more suited than Flash smelters for the recovery of copper from secondary materials. This is because of the different ways that the feed material is inserted in both furnaces. In Flash smelters, the ore and fluxes needs to be fine and completely dry in order to be able to blow the mixture inside the burner area of the furnace. The feed material for TSL smelters show less constrains concerning humidity and particle size. The material is dropped from the top inside the molten bath. As a result, a more complex and flexible feed stream can be processed using TSL smelting (Wood, Hoang & Hughes, 2017). This feature will become more important in the future as primary copper sources gets more scarce and the need for a fully sustainable material cycle increases.

Jan 1, 2019

By S. N. Rossovsky

"A new method for the hydrometalfurgical treatment of refractory gold arsenosulphide concentrates is presented. Themethod involves a combination of' finegrinding, intensive agitation, flotation, and cyanidation, and consists of leaching of -10u pyrite and arsenopyrite particles in alkaline solution under intensive agitation without the application of costly high-pressure and roasting techniques. Consistent extractions of gold, in excess of 96%, are achieved.IntroductionConventional methods of alkaline leaching of gold arsenosulphide concentrates in an autoclave» and under electrochemical oxidation( 2) require expensive equipment as well as high-cost energy and reagents. In other cases, processing of gold concentrates inelude: ultra-fme grinding, calcination at 200°C to 250°C with the addition of an oxidant (NH4NOJ followed by alkaline leaching of the resulting calcine with hydrogen peroxide, the latter being a complicated method yielding poor extractions of gold (89% to 90%). In this paper, a hydrometallurgical method is described for processing refractory gold arsenosulphide concentrates in which alkaline leaching is followed by cyanidation of the residue."

Jan 1, 1993

By Navid Bahrani

Introduction ? Today?s economic market is motivating underground mining companies to increase development advance rates and enhance their NPVs. ? For example, block cave mining involves development of kilometers of drifts with multiple pillars. ? The cyclic nature of drill and blast, and its inherent tendency to damage the surrounding excavation rock mass and increase support demand often result in poor advance rates ? This has motivated mining companies to replace the conventional drill-and-blast as the main excavation method with alternative methods such as mechanized excavation. ? There is little experience with mechanized or non-explosive excavation methods in hard rock metalliferous underground mining.

Oct 1, 2010

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By Chris J. Pritchard

Pumpable, two-component resins for anchoring rock bolts provides significant advantages over traditional cartridge resin and cement grout systems where fast and easily adaptable support is required for difficult ground conditions. Cartridge resin anchoring with rock bolts is often ineffective in oversized, fractured and washed-out holes. Cement grouting of cable bolts is frequently plagued with QA and QC issues related to the grouting process. Installation of cable bolts with resin injection techniques is routinely completed in cycle allowing blasting immediately after cable bolting. Xstrata Nickel has evaluated the Minova Resin Injection System since 2007. The Nickel Rim Mine and partner Minova have tested and validated the Resin Injection process for bolting procedures including Hollow Fiberglass Bolts, Rebar, Modified Cone Bolts and Cable Bolts. The resin injection process is adaptable to most bolting processes and equipment. Currently, Nickel Rim Mine use 2 resin injection products with different set times to grout deep cable bolts and development support in highly variable ground conditions. The product predictability and adaptability in application along with a high crew acceptance continues to make this support process part of an adaptable ground support system. Product consistency and quality significantly reduce the quality control concerns for ground support in highly variable ground conditions.

May 1, 2011

By Melanie Grob

Two commonly estimated fractal dimensions, called b and D values, represent statistical characteristics in the distribution of magnitude sizes (b) and spatial hypocenter locations (D) of microseismic events, respectively. We postulate that the values of b and D are related to specific stress regimes. Through different case studies of fluid injection into an oil/gas reservoir or geothermal field, we infer that the measured temporal variation in fractal dimension b is most likely due to significant changes in the local stress regime. The fracture dimension D indicates the spatial clustering of events. The distribution of these events can vary with time because of stress perturbations that (re)activate fractures whose direction favours their movement under a specific stress regime. Thus a combined statistical study of these two dimensions can help infer the variations of local stresses in a reservoir.

Jun 1, 2012