Search Documents

By S. Yannacopoulos, L. Bichler, P. Wanjara, J. Gholipour

Characterization of a virgin and in-service Inconel 718 alloy was undertaken to study the changes caused by the service conditions on the grain size, ?? phase, MN-type nitrides and MC-type carbides. The size, distribution and volume fraction of these phases and grain size were studied using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and electron backscattered diffraction (EBSD) analyses. A considerable difference in the grain size, as well as distribution and volume fraction of the precipitates was observed in the in-service material as compared to the virgin Inconel 718. As a result of these microstructural changes, a notable dissimilarity in hardness between the materials investigated was observed. The results presented in this study are important for proper development of repair parameters and heat treatment of in-service Inconel 718 material.

Jan 1, 2014

By J. Ji, A. Shi, B. Grcic

Floating copper minerals selectively against iron minerals such as pyrite has been challenging for most copper and copper/gold deposits, and many operations continuously strive to maximise copper recovery whilst meeting target concentrate grades. Maximising grade is achieved by selectively floating copper minerals and rejecting pyrite. This challenge is to minimise copper and gold losses in the roughers if this approach is used. A flotation testing program was conducted by Bureau Veritas Minerals on a high-level pyrite bearing copper/gold ore sample to establish the potential to reject pyrite in the rougher stage, but also maximise copper and gold recoveries, and ultimately final product grades. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. The main variables tested for achieving selective flotation of copper and gold were collector type and pH control, through lime addition. Grind sizes used in the rougher and cleaner tests had been established from previous test work. The collectors tested were SIPX, Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The two best performing collectors were then tested in open-circuit cleaner tests, with the optimum conditions examined further in locked cycle tests. INTRODUCTION Bureau Veritas Minerals Metallurgical Division was retained by Eldorado Gold Corporation to perform a metallurgical testing program on a high-level pyrite bearing copper/gold ore sample from a gold- copper porphyry deposit to optimize flotation reagent scheme to improve gold and copper recoveries and copper content in the concentrate. The test program included feed characterization, rougher and open-circuit cleaner flotation as well as locked cycle flotation tests. Initially, various collectors were screened in kinetic rougher tests, and over a pH range of 8.5 (i.e the natural ore pH) up to 11.5, using a primary grind size of 80% passing 120 µm. The collectors tested were SIPX (sodium isopropyl xanthate), Aerophine® 3418A, Aerophine® 3421, Aerophine® 3422, Reagent S-11192 Promoter, Reagent S-11193 Promoter and FloMin C4150. The enrichment ratio, which is the ratio of copper to sulfur in the concentrate to that in the feed, was used as proxy for rating selectivity (i.e. degree of pyrite rejection or depression).

Jan 1, 2019

By Stephen G. Hardcastle, Michel G. Grenier

"Safety and health issues are and have been in the last decade a very high priority item with all parties involved in the Canadian mining industry. As a result of this high level of concern for workers' safety and health, Canadian mines are at the leading edge of environmental control technology. For the most part, the occurrence of pollutants in mines is unavoidable. Dust from mining operations, airborne radiation, gases and heat from the strata as well as gases and particulate from diesel engine emissions will undoubtedly be found to some level in most Canadian mines. A lot of work remains to be done, however, in order to bring all Canadian mines at the same level of proficiency when it comes to safety and health. Also, more work is needed in order to maintain our status as world leaders in this field.CANMET's Mining Research Laboratories (MRL) in Elliot Lake and Bells Corners, Ontario, with the cooperation of the mining industry, have contributed to improving environmental conditions in underground and surface mining and milling operations. The extent of collaboration and efforts vary widely from long-term, multi-million dollar projects between several interested parties to smaller projects involving one laboratory and a single mining operation. This paper gives examples of such collaborative efforts and potential future directions as they apply to: mine ventilation analysis using tracer gas techniques, optimization of mine ventilation network efficiency using real-time monitoring and controlled recirculation (heat saving), respirable dust and radiation sampling and control techniques, diesel emission control using regenerative ceramic filters and, finally, the control of sulphide dust explosions and resulting sulphur dioxide production."

Jan 1, 1990

By R. G. Gillies, C. A. Shook, W. H. W. Husband

"The current state of knowledge concerning pipeline transport of coal in water slurry form is summarized for the four categories: coal-water fuels, conventional fine coal slurries, coarse coals and stabilized mixtures of coarse and fine particles. Surface chemistry is of dominant importance for coal-water fuels and considerable progress in understanding the role of surfactants has been achieved in recent years. Little generalized research on the flow of conventional fine coal slurries has been done in the past 17years, although innumerable conceptual designs and feasibility studies have been undertaken. Coarse coal slurries are fairly well understood but the model which explains their flow requires more data to be established fully. Stabilized flow mixtures should probably obey the same model as coarse coal slurries but experimental results for stabilized mixtures have not yet been incorporated in a comprehensive theory.IntroductionPipeline transportation of coal in a water vehicle has been employed for many years in coal washeries. It has been used less frequently in hydraulic mining and thermal power station fuel supply systems. The suitability of coal for pipeline transport arises from its moderate specific gravity relative to the carrier fluid and the fact that throughputs are often large and steady over long periods of time."

Jan 1, 1990

By W. J. D. Stone

"INTRODUCTION Over the past decade, a number of publications have described the advances in High Intensity Wet Magnetic Separation. A number of significant, but small capacity installations were made and are successfully operating. These were followed some three years ago by larger installations treating ilmenite gravity concentrates; at least one machine treating 25 tons per hour of new feed was installed and is successfully operating.However, this still did not result in general acceptance that High Intensity Wet Magnetic Separation could be applied on a large scale. Neither did it dispel the feeling that High Intensity Wet Magnetic Separation was ""expensive"" and hence, confined to small scale – high value applications suchas the cleaning of tin concentrates. In addition, there is the usual reluctance of being the ""guinea pig"" which has resulted in waiting to see ""someone else"" make the first large installation decision. Such a decision and installation has now been made.Therefore, the purpose of this paper is to show that High Intensity Wet Magnetic Separation has been commercially accepted on a large scale and to show its general application to the base metal mineral industry.Examples are confined to a few specifics due to the large volume of preliminary test data that is available. The art has now reached the stage where much of the preliminary work should be taken through to serious evaluation."

Jan 1, 1971

By X. Cao, X. -G. Chen, K. Liu

As is well known, the standard Al-Cu 206 cast alloys have extremely low iron contents, usually less than 0.15 wt. %. Recently it is found that the iron contents of the 206 cast alloys can be extended up to 0.5 wt. % through the precise control of the iron-rich intermetallic phases. In the present work, the tensile fracture surfaces of the 206 cast alloys with various iron contents are systematically analyzed to understand the failure mechanisms. Results show that higher iron contents can reduce the tensile properties (especially the ductility) of the alloys mainly due to the increasing volume percent and size of the iron-rich intermetallics. Tensile failure mainly occurs at the iron-rich intermetallics/matrix interfaces for the platelet ß-Fe, but by the self-disassociation for the Chinese script a-Fe and Alm(FeMn). Cracking is easier to initiate and propagate along the longitudinal axis of the platelet intermetallics, but it can be deflected along the branches/arms of the Chinese script iron-rich phases, making the alloy more resistant to the propagation of the cracks, and thus the Chinese script iron-rich intermetallics are less harmful than platelet ß-Fe. In addition, it was also found that the Chinese script a-Fe has even a less damaging effect compared to the Chinese script Alm(FeMn) due to the relatively small size and compact morphology.

Jan 1, 2014

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By R. Pakalnis, D. Tenney, B. Lang

"This paper describes three case histories whereby numerical methods were employed as a tool in the identification of potential instability. Simple two dimensional (PCBEM) and pseudo three-dimensional (BESOL, MINTAB) codes were employed to identify zones of induced stress which were subsequently related to extensometer, stress meter and observational data as the stope was excavated. The following case histories will be discussed. MacLellan Mine - sill pillar stability; Ruttan Mine-Hanging Wall Stability; and Detour Lake Mine-narrow vein mining.The MacLellan case history showed how modelling and instrumentation enabled mining to be conducted safely and under controlled conditions. MINTAB and PCBEM were employed to predict sill pillar failure. The sill pillar failure was associated, with an unloading of stress which was recorded by instrumentation (stress meter) and a decrease in the over-all rock mass strength. The yielded pillar, however, maintained its over-all configuration enabling access through the pillar.The Ruttan case history is an example of hangingwall and footwall design whereby the existence of adverse structure coupled with a zone of relaxation results in dilution. BESOL and PCBEM were employed to model a test stope and to verify the observations and measurements through instrumentation . Empirical methods of dilution estimates are employed to determine the level of walls lough with respect to the rock mass rating, stope dimensions and rate of excavation.The Detour Lake case history in an example of open stoping a narrow steeply dipping deposit. Stope dimensions are 135m in strike length, 47 m in vertical height with an average width (F/W to H/W) of3.6 m. Stress meters coupled with visual observations are related to modelled estimates of stress and dilution."

Jan 1, 1991

By R. E. Stewart

"Using the concept of economic life and marginal analysis, it can be shown that proper equipment replacement timing can save a mining company many thousands of dollars. To assist management with determining the economic life of mining equipment, a new computer package has been developed. The package, called ERG (equipment replacement guide), incorporates all important economic factors related to equipment usage, such as operating costs, maintenance costs, salvage values, depreciation, volume of work, tax credits, inflation rates, ROJ, etc. The information is used in a series of equations which balance the costs of new equipment against the total cost of old equipment. The solution of the equations determines economic life and the point in time when the old equipment should be replaced. IntroductionIn an operating mine, equipment must eventually be replaced or downgraded for a variety of reasons. Fleets of haul trucks, dozers and other major pieces of equipment deteriorate over time until the mounting costs of maintenance and repair force either a major overhaul or the ir replacement by new and more efficient pieces of equipment.The question of determining the best time to replace old equipment has been approached in many different ways. Various methods, ranging from operating experience, intuition and physical necessity to sophisticated computer models have been devised to help cope with equipment replacement decisions . The best of the se will incorporate the most important economic factors related to equipment usage, such as operating and maintenance costs, salvage values, depreciation, work delivered, the cost of capital, tax credits and, of course, the effects of inflation.Economic TheoryThe fundamentals of equipment replacement theory grew out of the interaction between economics, engineering and finance. The use of annual cost comparisons and rate-of return calculations were helpful in handling situations in which assets with different finite lives were being compared. Later developments bringing together the concept of economic life and marginal analysis helped provide additional refinements to the theory. Taylorui showed that the displacement of an aging asset with a similar, but newer, asset can be justified economically when the marginal cost of keeping the asset one more year exceeds the minimum uniform annual cost equivalent of the proposed replacement."

Jan 1, 1980

By G. Armand, A. Noiret, D. Seyedi, J. Morel

"Clay formations in their natural state exhibit very favorable confining conditions for repository of radioactive waste because they generally have a very low hydraulic conductivity, small molecular diffusion and significant retention capacity for radionuclides. Nevertheless, one concern regarding the hydromechanical behavior around drifts in such claystone is the associated pore pressure field disturbance during excavation works. In the short term, the very low permeability leads to an almost “undrained” condition, meaning that the stress change due to face advance will create volumetric strains leading to an increase or decrease of pore pressure. If the effective stresses reach the failure level, the induced damage around these excavations might change the favorable properties of such formations. To demonstrate the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW) in the Callovo-Oxfordian claystone (COX) formation, the French national radioactive waste management agency (Andra) started in 2000 to build the Meuse Haute-Marne underground research laboratory (M/HM URL). The present paper illustrates observed pore pressure changes during excavation of drifts (˜5 m diameter), of micro tunnels (˜0.7 m diameter) and a borehole (˜0.15 m diameter). All these openings are parallel to the major horizontal stress at the main level of the M/HM URL. In drifts parallel to the major stress (i.e., when the initial stress field in the drift section is quasi-isotropic) an important increase followed by a drop of pore pressure is observed in the horizontal plane at the drift wall. These observations emphasize the impact of the in situ stress state and rate of excavation on the pore pressure and provide important insight of the hydro mechanical behavior of the COX claystone and the relationship between pore pressure and excavation induced fractures zone."

Jan 1, 2015

By A. Vasebi, É. Poulin, A. Desbiens, D. Hodouin

Maximizing benefits generated by separation plants in the mineral processing industry is of prime importance. To achieve this goal, observers and controllers are both key tools playing a crucial role for economic optimization. Although these methods have been widely discussed in the literature and that numerous applications have been reported, coupling the different algorithms raises practical challenges. The economic function definition, the selection of the real-time optimization structure, the elaboration of observer and controller models, the controller development, and the tuning of stochastic and deterministic parameters strongly influence economic performances. The objective of the paper is to discuss the major difficulties related to the implementation of a real-time optimization system and highlight the benefits of linking data reconciliation and model predictive control for a simulated flotation plant. A systematic topdown approach is used to go through the main design phases and to comment on the different options available for the development of the optimization structure. An internal model predictive controller coupled with a stationary observer is applied for the direct optimization of a three-stage flotation plant simulator based on a phenomenological model. The results show performance improvements in terms of increased revenues brought by reduced grade variability and collector consumption. The discussion also proposes alternative avenues that could be taken to achieve comparable improvements. Finally, since the limited simulated case-study cannot provide a complete understanding of the benefits brought by a data reconciliation observer, recommendations for industrial applications, which are more complex, are provided to promote effective implementations.

Jan 1, 2016

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By Q. Han, W. Dai

Al-Ti-B type master alloys have been widely used in the grain refinement of aluminum since 1940s. The introduction of Al3Ti and TiB2(AlB2) particles reduces the grain sizes down to about 200 micrometer level and makes cold work possible. However, the mechanism for the grain refinement is still not clear, though it is believed that TiB2 in the presence of Al3Ti nucleate a-Al grains in solidification. This paper presents our finding on the formation of (Ti,Al)B2 solid solution, which leads to a proposed theory on grain refinement by Al-Ti-B type master alloys that upon addition into aluminum melt stable TiB2 particles react with aluminum slowly and release titanium into the melt. The titanium thus released in combination with titanium in the melt through dissolution of Al3Ti maintains a transient titanium-rich layer on the surface of (Ti,Al)B2. This layer offers a low crystal mismatch with a- Al and promotes the nucleation of aluminum grains.

Jan 1, 2014

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By D. MacGREGOR, VERA TUREK

The Badgeley Island quartzite deposir in Georgian Bay is worked by lndusmin Limired and was developed in 1969 to produce a high-qualiry silica for use in rhe ferrosilicon and glass industries. The quartzire is part of the Precambrian Bar River Formarion, and is a generally whire, fine-grained rock containing rhin sericire seams. Primary sedimenrary features wirhin the deposit are bedding and ripple marks. Amphibolite and diabase dykes cur the quarr zire body.

Jan 1, 1984

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By M. Lahtinen, B. Saxén, M. Latva-Kokko

The conventional jarosite precipitation process with neutralization by zinc calcine is widely utilized in the zinc industry. However, it has a significant drawback of causing losses of valuable metals like zinc, lead and silver to the jarosite. This comes mainly from the content of these metals in the calcine used for neutralization. As the zinc plants today want to maximize metal recoveries and minimize the amount of residues, this matter has become more and more relevant for zinc producers. Outotec developed and patented in early 2000 an improved version of the jarosite precipitation process in which the need for neutralization can be minimized, thus the metal losses to the jarosite also can be minimized. At the same time, the iron content of the jarosite increases and the amount of produced jarosite is smaller. The main feature of this process is to start the precipitation from ferrous iron after having reduced all the iron by zinc concentrate in a separate step before jarosite precipitation. Iron is then oxidised back to the ferric form simultaneously with jarosite precipitation. By this method, the formation of sulphuric acid is only half that compared to the conventional method and the need for calcine for neutralization can be avoided. High mixing and oxygen dispersion capability are needed in this jarosite precipitation process. Such capabilities are found in the Outotec OKTOP® reactor series. High performance reactors are not only needed to generate high quality precipitates, but also to maximize oxygen utilization; i.e., to minimize operation costs. Outotec’s latest development in this area is the OKTOP® plant product in which not only the reactors, but also all the accessories are designed, manufactured and delivered by Outotec. One responsible supplier ensures efficient and fast delivery and can provide mechanical and performance guarantees for the entire plant unit.

Jan 1, 2016

By Sadan Kelebek, Gerhard W. Heinrich, Peter F. Wells, Peter J. Whittaker

"Based on plant mineralogical data & circuit modelling, a pilot plant campaign was conducted at Strathcona Mill to identify options for improving the performance and operating flexibility of the copper-nickel separation circuits. Emphasis was given to options for combined treatment of the two feed streams (primary nickel ore rougher concentrate and copper ore circuit concentrate) to obtain more flexibility in the use of existing column flotation capacities. The pilot test results demonstrated that circuits which incorporated preconcentration prior to column flotation gave the best metallurgical results. Maximum column carrying rates were also related to the preconcentration. Predictions that increased circulating loads from the column scavengers would improve copper-nickel separation performance were confirmed.IntroductionThe copper-nickel separation circuits at Falconbridge's Strathcona Mill produce a high grade (>30% Cu) copper concentrate most of which is treated at the Falconbridge Kidd Creek smelter near Timmins. The remaining nickel concentrate which still contains approximately 20% of the feed copper is combined with other lower grade nickel/copper concentrates and shipped to the Falconbridge nickel smelter. The separation is required because of the limited capacity for copper processing in and downstream from the nickel smelter. Since no nickel is recovered at present in the Kidd smelter, the challenge is to minimize the nickel content of the copper concentrate.At present there are two independent separation circuits treating the rougher concentrates from the copper and nickel circuits as shown in Figure I. The minerals treated are mainly chalcopyrite and pentlandite but there is up to 25% of the copper present as cubanite in the copper ore. The circuits were kept separate because the flotation rates and froth characteristics were very different, probably because of the presence of cubanite and the large difference in the concentrate grades feeding the circuits."

Jan 1, 1995

By Robert B. Parsons

"During hard times, the focus on tax issues makes a slight change in direction. Mining companies contemplate the tax treatment of transactions and circumstances which are the product of a difficult financial environment. Some of these issues are discussed in this month's edition of Tax Notes.Every industrial sector in Canada is undergoing a major restructuring of some form, and the mining industry is not an exception. The longest recession since the Great Depression continues to affect the economy. Mining firms seek to bring their debt/equity ratios into line, and try to replenish depleted retained earnings by selling assets. This month, Tax Notes briefly examines some of the tax issues which are generally encountered during the course of such a restructuring process.Debt SettlementOne question which commonly arises during hard times concerns the tax treatment of a "" gain "" realized by a debtor on the settlement of a debt. Consider, for example, a simple situation where a creditor wants to protect itself from further losses, and makes a deal with the mining company to accept a cash payment of $8 million in full settlement of a $10 million loan. In financial terms, the debtor has made a $2 million gain on the settlement of the debt. What is the tax treatment of that gain?The Income Tax Act (the Act) contains provisions in section 80 of the Act and in section 5400 of the Income Tax Regulations which deal specifically with this question. First of all, it is noted that the $2 million gain is not brought directly into income for tax purposes. However, as indicated below, the gain could affect the debtor's income indirectly to the extent that certain of the debtor's tax pools must be reduced by the amount of the gain."

Jan 1, 1993