Search Documents

By Juergen Antrekowitsch, Stefan Steinlechner

"Waelz oxide from steel mill dust recycling is usually sold to the primary zinc industry, where it is first charged to the roasters to eliminate the remaining fluorides and chlorides. This limits the overall amount of secondary materials which can be used because of different operating problems in the roasters. Another option, in the case where the halides are low, would be direct leaching with low or medium concentrated sulphuric acid. Unfortunately, because of the carryover of some steel mill dust, iron is also present in the Waelz oxide, reaching contents up to 5 wt.%. Since the objective is to treat the solution more or less directly by electrowinning, with only a few simple preliminary purification steps, iron in the solution is a very important factor. Various trials have been done to investigate the dissolution behavior of the iron contained in the Waelz oxide. Although the zinc extraction should reach a maximum, all other elements, especially iron, should be low. This paper describes the results of our research in this area and offers possible options for Waelz oxide utilization. There is also a focus on how other elements, present in the material, influence the dissolution behaviour of zinc and iron, and whether a loss of zinc is unavoidable, if low iron dissolution is required.INTRODUCTION One of the most important secondary zinc resources is the zinc oxide originating from steel mill dust recycling. For the treatment of high zinc containing steel mill dusts, the Waelz kiln process is the so called “best available technology” and it dominates the industry, with roughly a 90% market share. The product Waelz oxide contains mostly zinc oxide, but it also contains lead compounds and halides due to evaporation with the zinc. In addition, it contains iron and some slag compounds due to mechanical carry-over. The presence of halides limits the use of the material as an alternative concentrate for primary zinc electrowinning. Such halides can be reduced to a certain extent by washing and/or solvent extraction (see following chapter). Although lead is not troublesome and theoretically represents a second recoverable valuable metal, iron is unwanted and causes additional problems during leaching. Even though Waelz oxide is generally a highly welcome input material in primary zinc metallurgy, due to its high zinc content, it still contains halides, and in the majority of cases, the oxide must first be treated in a roasting process. Different circumstances, like accretion formation because of the lead and halogen compounds as well as unwanted cooling effects in the roaster, limit the amount of Waelz oxide which can be substituted for the primary concentrate. Another, even more limiting factor, is the allowable concentrations of chlorides and fluorides in zinc electrowinning, the last step in the primary zinc processing route (Ruetten, 2011)."

Jan 1, 2016

By H. H. Claudet

PROBABLY the first flotation mill for treating molybdenite ores was put into operation .in Norway during 1913, when the writer was employed to introduce and apply the Elmore vacuum flotation process at a mine in southern Norway. These operations proved successful and led to other similar installations in that country. It remained, however, for Norwegian engineers themselves to iron out their difficulties and establish the molybdenum industry on a basis which ultimately attained world importance. Just as today, an urgent demand for molybdenum arose during the world war of 1914-18. By 1916, many molybdenite properties were in operation in Canada and several small concentrating mills were under construction. At one of these, in the Ottawa Valley district, the opportunity came for applying the Elmore vacuum flotation process, using a flow-sheet similar to that adopted in Norway. Later, as one of the staff of the General Engineering Company, who had already developed a highly efficient flowsheet for treating molybdenite ores, using the Callow pneumatic flotation process, the writer devoted considerable time to research work and investigations on a number of molybdenite projects and deposits in eastern Canada. The bulk of Canada's production of molybdenite was coming at that time from the Moss mine at Quyon, Que., where concentration of the ore was effected by water-film flotation. It is of interest to note that this process, based on the principle of surface tension, had been developed and introduced by the late Henry E. Wood, of Denver, Colorado- one of the original owners of the Moss mine-at the time he was investigating the Elmore vacuum process in his Denver plant. The process, with certain modifications, was used at several other properties in eastern Canada, and notably in the ore dressing laboratories of the Department of Mines at Ottawa and in a plant at Renfrew, Ont., in both of which ore from deposits in various parts of Canada was treated, with recovery of very appreciable amounts o much needed molybdenite. During the summer of 1917, the water-film flotation mill at the Moss mine was dismantled and the plant was re-modelled by the General Engineering Company to include the Callow system. This installation, using improved flotation methods, was highly successful both as to recovery and grade of concentrate, and proved a decided advance in molybdenite concentration, a recovery of upwards of 90 per cent being obtained, with a concentrate grading over 90 percent MoS2.

Jan 1, 1944

By M. M. Hajdasinski

"Any study in the field of theoretical investment analysis, or practical project evaluation, must be based on the assumption of one of the commonly applied models of time and value representation, and the corresponding interest convention. The lack of clear assumptions in this regard may easily confuse both the author of the study and the reader, and sometimes even lead to inaccurate results.In the first part of this paper formal definitions of the continuous and discrete models of time and value representation are introduced; in the second part, the importance of transparent assumptions is shown using a concrete example of inflation calculation in project evaluation.IntroductionIn his recent paper, L.D. Smith(10) discusses an important aspect of mine investment analysis: inflation in project evaluation. His interesting presentation of current practices of handling inflation by Canadian and international mining companies in their feasibility studies ends, in the conclusions, with a call for clear assumptions made when evaluating mining projects.With this call, an important issue has been addressed. The lack of clearly stated assumptions, or their incompleteness, are relatively frequent with regard to the interest convention or the model of time and value representation assumed when evaluating mining projects. It is, for example, fairly common that the quantitative evaluation of a project is performed according to the discrete model of time and value representation and the discrete interest convention, and the graphical presentation, supporting this evaluation, reflects the continuous model.Sometimes such an ambivalency means nothing more than just a formal inconsistency; there are cases , however, that may well lead to a serious confusion and /or to inaccurate results . Before this can be demonstrated on a specific example, a concise description of the models of time and value representation used in the evaluation of industrial projects seems to be in order. Although these models (especially the discrete one) have been in common use in the research and practice of financial analysis for considerable period of time, they have been applied rather intuitively, and their forma] definitions are difficult to find even in the standard textbooks on Engineering Economy."

Jan 1, 1990

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By Malcolm R. Gent

"The presence in Saskatchewan of sixteen kimberlite pipes of probable late Albian age has been reported. An abundance of aeromagnetic anomalies possibly attributable to kimberlite pipes have been identified and it is anticipated that industry has acquired reasonable proof of the presence of more than seventy k imberlite pipes in Saskatchewan. Historical reports of diamonds, the discovery of kimberlite pipes and these aeromagnetic anomalies indicate the Phanerozoic Basin and some parts of the exposed Shield in Saskatchewan have an excellent potential f or the occurrence of economically exploitable diamond deposits. The presence of some igneous minerals found in some salt solution breccias also indicates the probable occurrence of extensive diatreme activity during the Devonian.A Laramide Orogeny-induced crustal hinging or arching of the eastern margin of the Phanerozoic Basin and probably dextral wrenching-induced arching and faulting within the basin are proposed as major factors in the emplacement of Cretaceous or younger kimberlites. Zones of crustal weakness between subcratonic Archean blocks and internal faults are also thought to be significant controlling factors in the location of kimberlites in Saskatchewan.Mapped aeromagnetic anomalies interpreted as being possibly due to kimberlite pipes generally tend to be concentrated in, areas underlain by a basement of or with components of Archean age. Within Saskatchewan, these anomalies occur within the probable Trans-Hudson Orogen zone; the Rae-Hearn Craton margin; and the northeast flank of the Elkpoint Basin. Recognized areas of potential f or kimberlite emplacement are the Phanerozoic basin margin, the western limit of the Superior Province adjoining the Churchill Province, and a swath approximately 150m wide along the northeast-southwest trending Shaunavon linear and other areas of inner basin arching."

Jan 1, 1992

By D. Kao, J. Gogal, S. Humphrey, T. Byrne, M. Davoodi

"High total and dissolved uranium values were noted in the process water at the Cigar Lake Operation (CLO) during early production start-up period, whereas significant levels of dissolved uranium had not been observed previously at similar operations. The excess dissolved uranium resulted in higher demands on the water treatment plant, along with higher operating costs, environmental risks and some unrealized revenue potential. A species balance indicated that uranium was leaching into solution in the grinding, dewatering, and storage circuits under normal operating conditions. Jet boring, water recycle, ball milling, and the use of Pachuca tanks for ore storage results in a highly oxidative environment, which is favourable to leaching.This paper will outline the testwork performed to identify the conditions under which the uranium leaches into solution and to determine required conditions for uranium precipitation. Maximum uranium leaching was found to occur under normal operating conditions (pH ranging from 7.0 to 8.5); testwork indicated that both lowering and raising the pH can significantly reduce the uranium leaching. Analytical results combined with the batch scale testwork indicate that the uranium solubility is associated with carbonate species in the ore. Uranium precipitation was maximized at pH values greater than 10.5 or less than 6, corresponding well to carbonate leaching and precipitation values from literature. Higher precipitation efficiencies were noted at high pH ranges.As a result of this work, a pH control system has been implemented in the Pachuca storage vessels and thickener prior to water treatment plant on a trial basis. Caustic soda is recommended for pH control due to ease of operation, economic viability and material requirements and downstream constraints."

Jan 1, 2016

By P .. D. Vaillancourt, D. F. Sangster

Several occurrences of disseminated galena, including a former producing mine, are found in Pennsylvanian fluviatile sandstone of the Salmon River Basin, Cape Breton Island, Nova Scotia. Detailed study of the distribution of these occurrences has revealed that highest galena concentrations are found in sandstone overlying channel-shaped depressions in felsic basement rocks. These buried depressions, in turn, correlate in position with modern streams in areas of basement exposure. This correspondence suggests that the latter are at least partially controlled by an exhumed Pennsylvanian topography. If this is correct, then several other streams in the area, lying on basement, may be used to locate possible undiscovered lead deposits in sandstones of the Salmon River Basin.

Jan 1, 1990

By J. Bouchard, R. del Villar, A. Vazirizadeh

"Industrial flotation is a continuous and often multistage process, where particles of a given mineral species (usually the targeted one), present in different sizes, encounter a large amount of gas bubbles (normally air) to produce mineral–bubble aggregates, which are removed from the flotation device (cell or column) as a valuable product (concentrate). The bubble content inside the cell is characterized by the prevailing hydrodynamic conditions (known as gas dispersion variables), which in turn are known to influence the flotation performance. Although most researchers and practitioners agree that the relationship between the hydrodynamic variables and flotation performance exists, the lack of an adequate method foronline measuring the average bubble diameter has prevented such studies.The aim of this study is to apply appropriate hydrodynamic variables for flotation kinetic modeling (as a key feature of flotation performance) for a given introduced particle size distribution (PSD). In this regard, experiments were conducted in a laboratory flotation column (5.6 cm internal diameter for a total height of 650 cm), and mixtures of quartz (hydrophilic gangue) and talc (naturally hydrophobic mineral), classified in four different size fractions. The correlation between the flotation rate constant and given hydrodynamic variables were analyzed. Results suggest that the relative importance of hydrodynamic variables for flotation rate modeling depends on the PSD. Finally the suggested hydrodynamic variables for each of the various particle size-classes considered were used to produce single variable models for the flotation rate constant. INTRODUCTIONIndependently of the prevailing flotation conditions, the mechanisms for bubble-particle aggregation and the residence time of the phases inside the device must also be considered. In this regard, one of the most used approaches to represent the overall flotation process is as a pseudo-chemical reaction between a particle and a bubble, whose rate (at a given time) is proportional to the amount of remaining floatable species. The proportionating constant is called the kinetic constant or the flotation rate constant."

Jan 1, 2016

"In 1989, improved milling and recoveries resulted in a record production of 7 722 200 Ib Nb2P5 at the Niobec Mine. At the beginning of 1990, proven and probable reserves stood at 11 952 000 tons grading 0.65% Nb205. This year, the world steel market has slowed and as a result, niobium consumption is down. Consequently, production at the mine dropped 14% for the second quarter.IntroductionThe Niobec Mine is located approximately nine miles northwest of Chicoutimi, Quebec, (Fig. I). After ten years of production, the Niobec Mine is the only operating niobium mine in North America and the second largest producer of niobium in the world after Brazil.The Niobec Mine is a joint venture held equally by Teck Corporation and Carnbior. Teck Corporation operates the mine while Cambior is responsible for marketing and selling the niobium pentoxide concentrate (Nb2P5).The deposit was discovered in 1964 following an airborne radiometric survey in search of uranium. However, mining of the deposit did not begin until 1976. The initial production capacity of 1500 tons per day was increased several times to the present capacity of 2450 tons . The deposit is considered as an ample source of pyrochlore concentrate for at least 15 years at the present production rate.Niobium, also known as columbium, is a greyish-white metal used primarily as an alloy in various steels and other metals. The use of niobium in alloys heightens tensile strength and improves corrosion resistance while at the same time reducing the weight of the alloy. Niobium is also used in the fabrication of steel for the aerospace, automobile, and oil and gas pipeline industries. Although substitutes for niobium exist, their use often results in diminished performance and net cost increases."

Jan 1, 1990

By Robert B. Parsons

"With several hoots of the whistle, Canada's fiscal engineers are once again cranking up the income tax locomotive, in an effort to inject new stimulus into a stubborn economy. And once again, additional gears, wheels, levers, and other mysterious part s are being added to the already complex machinery in order to accommodate the new push.This time, a significant new mechanism involves a major overhaul and expansion of the investment tax credit system.Although the shiny new devices have considerable appeal to a certain group of potential passengers, one wonders if all of the renewed chugging and huffing is on the right track.IntroductionAs indicated in Tax Notes in the July 1983 issue of CIM Bulletin , the April 19, 1983 federal bud get introduced a number of new measures which would permit investment tax credits and research and development deductions to "" flow through "" from a corporation to another taxpayer."

Jan 1, 1984

By W. J. Mcgaughey, R. G. McCreary, S. C. Maxwell, R. P. Young

"Seismic tomography is a process for obtaining images or maps of seismic velocity or other seismic properties of a rock mass. Seismic velocity images reveal variation in elastic moduli which, in tum, are related to several properties required in the geological or geomechanical assessment of a rock mass. Seismic velocity is sensitive to lithology, discontinuities, and in situ stress. Spatial or temporal variation of these properties may be indirectly assessed. Tomographic measurements are sensitive to volumes of ground, rather than determinations at points, or along lines or surfaces, as in conventional geological or geomechanical measurements or mappings.Tomography surveys are complementary to conventional measurements as they have the capability to interrogate a substantially larger volume of ground. They are thus useful in discerning trends or patterns in regions between or surrounding conventional ""point"" measurements of lithology, rock quality, stress, or other parameters of interest. Seismic velocity images give broad indications of trends in velocity; their spatial resolution of ground properties is typically on the order of five to ten per cent of the nominal survey dimension.Research in seismic tomography has been carried out for several years, and the capabilities and limitations of the technique in mining environments are beginning to be understood. This report reviews the present capabilities of seismic tomography surveys in mining, emphasizing rock mechanics applications. Six case studies are used as examples to demonstrate the capabilities of the method in assessing lithological variation, density and orientation of discontinuities, and the effects of stress."

Jan 1, 1994

By Guillermo Diaz, Roberto Pérez, René del Villar

"Pulp-froth interface position is a key variable in column operation. In plant practice, it is commonly estimated through a system of three pressure-transducers which allows the calculation of the pulp height. An alternate method based on the measurement of the conductivity profile across the interface has been proposed and successfully tested. Both methods however, present some practical problems related to the assumptions made in the calculation of the pulp height in the former case, and to the response time and the precision of the reading in the latter case.In this paper, the use of the neural network technique for improving the estimation of the pulp-froth interface in flotation columns is discussed. The technique is used with both conductivity-based and three pressure-transducer methods. Results obtained in a 2"" laboratory column and a 12"" pilot scale column are presented. A major obstacle in applying this approach in practise is the training of the artificial neural network. This problem is analyzed here for the conductivity-based method and some solutions are proposed."

Jan 1, 1995

By Clyde Williams

If you would allow me some liberties, I would re-state the title of this talk as Scientific Research, Our Greatest Resource, because that title would represent more clearly a present-day conception of the metals and minerals situation. It is a subject worthy of careful consideration. Canada and the United States are so similar and interdependent in their national economies that, in the following discussion, examples of conditions in the United States may? be interpreted to apply to Canada as well. Moreover, it is a striking fact that the per capita value of mineral production in Canada and the United States in 1940 was almost the same. Therefore, in the consideration of this subject, I have made no attempt to differentiate between the two countries. The consumption of the world's mineral resources in the last few decades, and particularly during World War II, has been so enormous as to require some form of magic to ensure the continued progress of civilization in the face of a diminishing supply of these resources which are so critically essential. As Dr. C. K. Leith pointed out in 1941, industrial expansion has been so great that, during the first forty years of this century, the world used more of its mineral recourses than in all preceding history. And this did not include the all-out consumption during the succeeding five years of war.

Jan 1, 1947

By R. W. Guill

"The Apex Mine is currently scheduled to be brought back into production by Hecla in the first quarter of1990. Its projected productivity rate will be exceptionally high for a small underhand cut and fill mine.The ore mined at the Apex Mine occurs within a pipe-like structure as a series of iron oxides containing both gallium and germanium, plus significant amounts of silver, zinc, lead, and copper.Ground conditions in and around the ore zone have dictated that unique approaches be utilized. To date, these have included a prototype 0.5 cu. yd diesel LHD, and the use of fibrous shotcrete in 4ft by 7ft headings, and the first pneumatically-placed cemented backfill in North America. Above all else, it is the combination of new technologies with a small and dedicated workforce which has allowed for the successful development of this ore body.IntroductionThe Apex Mine is an example of the typical small underground project. It has high grade, but low tonnage and is deposited in poor ground. In such cases, conventional planning and thinking generally results in an uneconomical evaluation and negative production decision. Fortunately, some unconventional thinking was allowed to take place during the planning and evolution of the Apex Mine development. The result now serves as an example of how such unconventional thinking can lead to the type of innovations described below.The job necessitated the development and use of new equipment and materials to execute a highly flexible underhand cut and fill mine design/pneumatic backfill concept, that must be constantly modified as different than assumed conditions become evident in and around the ore zone."

Jan 1, 1990

By M. Dosoudil

"Continuous pressure filtration is a modern process for the mechanical dewatering of flotation concentrates of coal and similar coal slurries. This method will give a lower moisture content than classical vacuum filtration, the improvement lying in the range 5% to 15%. Eighteen coal slurries have been examined in this survey. They are representative of a wide spectrum of filtered slurries. IntroductionDuring the last five years, a number of coal slurries have been tested either in the laboratory or with a pilot plant. The test pressure ranged from one to six bar. The results have been evaluated by mean s of a computer. Determination of the filter capacity and the resulting moisture content and energy consumption has been made with respect to the continuous pressure filter, Amafilter construction-type KDF (Fig. I) . Standard sizes of these filters are 60 m2, 90 m2 and 120 m2.The continuous pressure filter is a horizontal filter with a level tank. Six filter axles are mounted on a rotating main shaft, each with a particular number of elements attached. The elements rotate on their axes and move along a circular trajectory. Periodically the elements submerge into and emerge out of the slurry. A constant air pressure is maintained above the suspension, thus providing the pressure gradient necessary for filtration. The filtrate together with the dewatering air flows through the elements into the hollow axle and out of the filter."

Jan 1, 1987

By J. R. Morris, A. E. Ball, G. W. Kuzyk

"AECL Research has constructed an underground laboratory for the research and development required for the Canadian Nuclear Fuel Waste Management Program. The experimental program in the laboratory will contribute to the assessment of the feasibility and safety of nuclear fuel waste disposal deep in stable plutonic rock.In 1988, AECL extended the shaft of the Underground Research Laboratory (URL) from the existing 255 m depth to a depth of 443 m in cooperation with the United States Department of Energy (USDOE). The project, which involved carrying out research activities while excavation and construction work was in progress, required careful planning. To accommodate the research programs, full-face blasting with a burn cut was used to advance the shaft. Existing facilities at the URL had to be modified to accommodate an expanded underground facility at a new depth. This paper discusses the design criteria, shaft-sinking methods and approaches used to accommodate the research work during this shaft extension project.IntroductionThe Underground Research Laboratory (URL), a major geotechnical research facility, has been developed by AECL Research, 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program (CNFWMP), which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Hancox, 1986). The URL provides a representative environment to conduct a wide variety of geotechnical research relevant to nuclear waste disposal. Extensive characterization and monitoring programs were carried out prior to construction and will continue during operation. The operating phase experiments began in 1989 and will continue until the year 2CXXl (Simmons, 1990). Figure I shows the present extent of the URL facilities and the proposed future development."

Jan 1, 1991

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By Craig H. B. Leitch

"In describing the alteration of porphyry systems, the term ""secondary K-feldspar"" appears to be an oversimplification. A better term would be ""alkali feldspar"" alteration, because in actual fact the replacement feldspars show gradational changes from an albite, which is important in some systems, to an alkali feldspar containing minor orthoclase molecule, to true orthoclase.There are several textural varieties of secondary alkali feldspar present in the porphyry systems studied from British Columbia, Australia and New Zealand. These include, in apparent increasing order of alteration intensity: clear albite (An10); patchwork albite (Ab5-10); chessboard albite (An0-10) "" irregular albite "" (An0Ab100 to Ab90r10); untwinned "" anoralbite"" (Ab90Or-Ab70Or30); and orthoclase (Ab440Or60-Or100)·The exploration significance of these varieties of alkali feldspar is that their gradation in composition, from sodic to potassic, may be linked to a corresponding increase in intensity of alteration. Thus, there is a tendency for more sodic alteration feldspars to characterize weak, sub-economic deposits, or the fringe zones of stronger deposits; the more potassic alteration feldspars may provide an exploration vector toward more highly mineralized zones."

Jan 1, 1981

By Jiachen Wang

Longwall top-coal caving mining is one of the major mining methods for extracting thick coal seams in China. The top-coal caving longwall mining was began to use in the 1980s in China, and got the rapid development. The development of the top-coal caving mining technology in China, the achievements and the theoretical aspects progress of this method are described in detail in this paper. And the main technical model of China's top-coal caving mining is introduced in this paper. This paper also introduces the application of large-cutting-height mining in China and the technical level it has reached.

Aug 1, 2013

By D. Marotte, M. David

"A new exploration procedure is proposed for volcanogenic massive sulphide deposits of the Abitibi belt. ""Samples"" of acidic volcanic rocks (Si02 > 60%) were compiled from the literature. From the 574 samples collected, 322 were used in each of a number of experiments. Forward inclusion linear discriminant analysis performed on the untransformed geochemical data shows a general depletion in Na20 and CaO along with an enrichment in MgO for a ""proximal"" group of samples relative to a ""distal"" one. The percentage of misclassified samples reaches 20% to 30%, but test sets shows good stability.The exploration procedure was applied to the Normetal deposit, where the authors took 160 samples during the summer of 1977. It quickly leads to the definition of targets for more detailed exploration together with a good recognition of the old known deposit.IntroductionVolcanogenic massive sulphide deposits in the Abitibi belt (Quebec) are mainly found in rhyolites or acidic pyroclastics in the uppermost portion of a calc-alkaline volcanic series (Descarreaux, 1972). The deposits are thought to have formed syngenetically by the action of volcanic hydrothermal exhalations during the waning episode of a felsic volcanic cycle (De Rosen Spence, 1976). Alteration pipes of disseminated sulphides are commonly present. Metal deposition from hot springs, initiating convection cells in a submarine environment, may have been the dominant process in ore formation (De Rosen Spence, 1976)."

Jan 1, 1981