Search Documents

By G. C. Milligan

"A regional mapping program, conducted by the Nova Scotia Department of Mines, has shown that the George River Group of pre-Middle Cambrian rocks consists of a wide range of sedimentary and volcanic rocks, intruded by syenite, granite, granodiorite and lesser amounts of gabbro and diorite. Together, these rocks support the high ground of northern Cape Breton Island. Over this large area, the metamorphic grade ranges from low to extremely high.The rocks were folded prior to emplacement of the intrusions in Middle Cambrian time, and there was also post-Mississippian disturbance and faulting, but the structural history and pattern are still only imperfectly understood.Sulphide mineralization is known at Meat Cove, Lime Hill and in a number of smaller deposits. The most Cavour-able host rocks appear to be magnesian Iimestone, or schists derived from shales. Ail known sulphide bodies have an associated halo of retrograde metamorphism; in some cases, this is extensive enough to be used as a prospecting aidA vein of nickel-bearing sulphides has recently been re-discovered in the former gold mine at Second Gold Brook-an association which appears to be unique."

Jan 1, 1971

By M. K. Abel

"The Strathcona Mine is located in Levack Township on the North Range ofthe Sudbury Basin. The main orebody consists of pyrrhotite-pentlandite-chalcopyrite mineralization associated with an embayment of the footwall of the Sudbury Irruptive. A zone of massive chalcopyrite-cubanite-pentlandite mineralization occurs in a complex vein system in a series of mixed gneisses and breccias in the footwall. Vein widths vary from a few millimetres to 6 metres. In December 1979, this zone was estimated to contain 976,000 metric tonnes, with a grade of 9.31% Cu and 0.46% Ni. The vein system has a general strike of N 68°W at an angle of 60 degrees to the average strike of the footwall contact of the Irruptive. The dip of the vein system is 45 degrees sw. The strike and dip of individual veins in the system coincide with the directions that would result if a compressive stress had acted in a direction normal to the footwall of the Sudbury Irruptive, producing a conjugate set of fractures. The strike of the Irruptive at the Strathcona Mine is parallel to the long axis of the basin.IntroductionThe Strathcona Mine, owned and operated by Falconbridge Nickel Mines Limited, is located in Levack Township on the northwest rim of the Sudbury basin (Fig. I) . It is one of a group of nickel-copper sulphide ore deposits present along an 8.2-km section of the North Range of the Sudbury Irruptive. In the mines of the North Range, subunits of the Irruptive, going from hanging wall to footwall , include felsic norite, dark norite and dark norite breccia. The footwall complex at Strathcona includes the late granite breccia, which hosts a large proportion of the nickel-copper ores, and a compositionally variable group of brecciated and migmatized rocks, herein referred to as the feldspathic gneiss complex. It is within this latter group of rocks that the vein system of the Copper Zone occurs."

Jan 1, 1981

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By L. C. Galloway, P. M. Tiley

"Some progress has already been made in defining the parameters which will determine the performance of a guidance system in a mine shaft. Very little information is available, however, to help designers or operators predict the effects of varying these parameters in new or existing installations.The experience we have gained from monitoring a variety of installations has led to the development of a model which simulates the motion of a conveyance as it moves through a mineshaft, restrained by fixed guides.This paper presents a general analysis of the performance of the guidance system used in several installations, as well as a detailed description of the problem encountered at one mine and the steps taken to solve it.IntroductionOur company has investigated in some depth the problems that arise in the guidance of mine hoist conveyances.We have a telemetering accelerometer which we obtained to test mine hoist brakes. Frequently, during brake tests, the mine owners request us to use this instrument to measure the lateral motion of the conveyance ""to check guide alignment"". We have made such tests in shafts that have guide s of different kinds, including wooden guides, steel rail s and tubular steel guides. From these tests, we have gained some valuable information about guidance systems.In a well-aligned guidance system that is designed within common and well-known practice, the conveyance will experience very little shock most of the time. However, on rare occasions, shocks up to .5 g will occur. That is, the conveyance exerts a force of up to half its loaded weight on the guide. If the guide slips or is damaged by this force, it will be misaligned for future trips and become the cause of future shocks. In time, the whole guidance system can become misaligned."

Jan 1, 1982

By J. L. Gartshore

PRACTICALLY all of Quebec's chrysotile asbestos production derives from twelve mining and milling operations located in the "Eastern Townships" area of the province. The annual output of these twelve operations exceeds one million tons of chrysotile asbestos, valued at over one hundred million dollars, and is shipped to manufacturers spread over all six continental areas of the world. A total of approximately twenty million ton of asbestos ore yearly, or about seventy-five thousand tons a day, is mined. Individually, the operations vary in size from about two thousand tons to thirty thousand tons per day. Removal of waste rock and overburden to develop these ore tonnages varies greatly from one mine to another, but would probably average out at about a one to one ratio.

Jan 1, 1962

By M. Fall

The progressive depletion of ore available at shallow depths in several underground mines around the world means that underground mining operations would increasingly be carried out at greater depths and therefore at higher temperatures. However, our understanding of the effect of hot temperatures on the response (mechanical, economical, environmental) of cemented paste backfill (CPB) is still limited. Hence, an extensive laboratory investigation was conducted to study the performance of young and aged CPB, in response to deep mine temperatures. Several CPB samples with different compositions, cured at different temperatures (20 to 50°C) and different times (7 to 160 days) were tested regarding their mechanical properties, economical performance (binder consumption) and microstructural properties. The results show that hot temperatures significantly affect the performance properties of CPB at young and advanced ages. An increase in the curing temperature leads to a considerable improvement of the rate of gain of CPB strength and also to a significant increase of the strength of CPBs studied. CBP samples cured at hot temperatures show lower binder consumption and finer pore structure. Results of this study could serve as background information for the development of optimal mine backfill design procedures.

May 1, 2007

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013

By T. Motegi

Semisolid casting provides grain refinement of the cast structure and prevents macro-segregation. The conventional semisolid slurry is obtained by electromagnetic or mechanical stirring. In our process, the magnesium alloy (AZ31) slurry is made using an inclined cooling plate instead of the conventional methods. The slurry obtained is cast into a twin-roll caster and makes a continuous sheet of 2 or 3 mm thick. The most important factors that influence the sheet casting are the casting temperature and twin-roll speed.

Jan 1, 2007

By David A. Fawcett

"This paper presents a summary compilation of current Canadian coal research projects in the areas of exploration, mining and preparation. The compilation forms the basis for a review of present operations and technology, and of current research efforts. General research areas, requirements and priorities are suggested along with a discussion on achieving the research goals in terms of funds, facilities and staff. The current level of research funding in these areas is assessed. IntroductionCanada's coal production is expected to undergo major expansion over the next two decades in response to domestic demands on coal for electrical power generation, industrial uses and conversion to synthetic .fuels, and in response to export demands for both thermal and metallurgical coal s. Surface mining will continue to dominate, but underground mining will contribute an increasing proportion to total production.In Canada, coal research, particularly in the areas of exploration, mining and preparation (E, M & P), has been limited. Increased impetus has recently been given to this research with expansion of CANMET's activities and with the establishment of the Coal Mining Research Centre (CMRC). University researchers are branching into coal research; strata mechanics and preparation are popular in mining-related fields.With the increase in number of organizations and individuals involved in coal research, a means of keeping abreast of the ongoing work is necessary. An annual summary of the status of and developments in current research assists in providing this information. The CMRC prepared such a summary for Canadian coal E, M & P research in 1979 and it received favourable response, justifying the effort. A 1980compilation has been prepared and pro vides the basis for this paper; it is presented with a brief discussion on background, format and content.The compilation forms a basis for an examination of the current status of Canadian technology in E, M & P and of the ongoing research in each area. General research requirements are reviewed and programs and tasks are suggested, followed by a discussion of research goals in term s of priorities and achievement. An assessment is made of the level of research funding in Canada, with comparisons drawn from the United States, the United Kingdom and Australia."

Jan 1, 1980

By Nathan Deisman

Coupled reservoir geomechanical simulations have become a key component of caprock integrity assessments for SAGD operations. This work demonstrates the differences of stress evolution when considering coupled versus uncoupled reservoir simulation. Coupled simulation involves the use of a reservoir and a geomechanical simulator with feedback to each simulator to update reservoir or geomechanical variable (permeability, porosity, relative permeability, pressure, temperature, saturations). Uncoupled simulation only passes the pressure and temperature to the geomechanical simulation with no reservoir simulator updating. Therefore, it is possible to complete uncoupled simulations exclusively with no knowledge of geomechanical flow property evolution. However, it is important to understand the differences between the stress evolution in each model for caprock integrity analysis. A single geological model was selected and parametric analysis was completed while varying the geomechanical the production injection pressures (1600 kPa, 1900 kPa, 2200 kPa) for a reservoir with an initial pressure at the injector of 1300 kPa. The results of the six uncoupled and coupled models are compared through the changes in mean stress, shear stress, and strength with focus on geomechanical assessment of caprock integrity.

Jun 1, 2012

By J. D. Botsford

Westmin Resources Limited's H-W orebody on Vancouver Island is a copper/lead/zinc massive sulphide deposit that has been in production since 1985. The sulphur content of the ore averages 28% and in some stopes is as high as 53%. Several minor secondary sulphide dust explosions have occurred in development headings and cut and fill stopes, but as yet no known explosions have occurred in blasthole stopes. This pa:per reviews the history of sulphide dust explosions in the H-W Mine, factors contributing to the explosions and the preventative measures taken to control them.

May 11, 1988

By H. J. Glass, J. G. L. Bekkers

"In order to determine the feasibility of a hydraulic ore hoisting installation, the optimal operating conditions were calculated for applying such a system at the Detour Lake Mine of Placer Dome Ltd. Next, a financial analysis was conducted in order to estimate the cost per tonne for hydraulic hoisting of the ore. Subsequently, the cost per tonne was compared with the hoisting costs associated with a new borehole hoist. Installing a hydraulic ore hoist at Detour Lake Mine was found to be feasible with considerably lower costs per tonne of ore. The applied research method appears to be very functional and can be used to do similar research for other mining operations. IntroductionThe principle of hydraulic ore hoisting is well known, yet hardly accepted in hard rock mining. Application of the system would result in a smaller diameter shaft requirement and a flexible, easily expandable system. However, underground ore size reduction might be necessary and practical experience with the system is limited. Following recent innovations in the field of pumping hardware, e.g. new GeHo and Siemag Transplan equipment, hydraulic ore hoisting should be seriously considered for certain mining operations. As a case study, a design was made for the development of the newly found QK-Zone at Placer Dome Ltd.’s Detour Lake Mine. Hydraulic ore hoisting has been compared with conventional skip hoisting by establishing the optimal operating conditions and pumping equipment requirements for similar capacities at a selected mining operation. Generally accepted equations for slurry transport were used to predict the variation of pressure and power requirements as a function of hourly production and pipeline diameter. These data are used to select suitable equipment and estimate cost figures in order to make a financial assessment."

Jan 1, 1998

By S. Minamiguchi

Grain refinement is effective to enhance strength and ductility of metallic materials. However this advantage has not been utilized fully for magnesium alloys in industry because microstructure control through thermomechanical treatment is difficult owing to their poor deformability. The authors proposed a high-speed heavy-reduction rolling for production of Mg alloy sheets. It was found that the deformability is significantly improved at high speed and that the thickness can be reduced 60% by one-pass operation even at room temperature without fracture at the rolling speed higher than 1000 m/min. In this study, commercial AZ31B sheets were rolled at 2000 m/min between room temperature and 350°C, and quenched immediately after the rolling. The sheets rolled at 200°C show the finest recrystallized microstructure with the mean grain size of 2.2 Rm. They show outstanding mechanical properties with the tensile strength of 293 MPa, and the elongation of 25%. It is concluded that high-speed rolling is very advantageous for grain refinement and improvement in mechanical properties as well as deformability and productivity.

Jan 1, 2006

By B. E. Jones

"The area of uranium deposition is situated within the Churchill Province on the western edge of the Wollaston Iithostructural domain where it underlies the eastern edge of the Helikian Athabasca Formation. The Collins Bay deposit is 6 miles north-northeast of the Rabbit Lake mine. Two principal zones of uranium mineralization are described.The ""A"" zone is a partly eroded, high-grade pod of metal oxide and arsenides sheathed by clay-like minerals. It trends north-northeast and lies under 25 to 40feet of water. Uranium mineralization is localized at or adjacent to the unconformity between the Athabasca Formation and the basement rocks. The basement comprises a granitoid Archean terrain overlain by paragneisses of the Aphebian Wollaston Group. ""A "" zone ore contains phyllosilicates, quartz, pitchblende, rammelsbergite, pararammelsbergite, carbonaceous material, galena, gersdorffite, niccolite, carbonate and a trace of sphalerite.The ""B "" zone lies 6,000 ft south of the ""A "", and subcrops under till cover. It is a partly eroded zone composed of metal oxide and arsenides which occur within variably altered Athabasca Formation. Minerals recognized are phyllosilicates, pitchblende, niccotite, gersdorffite, millerite, carbonaceous material, pyrrhotite, skutterudite and a trace of galena. The Athabasca Formation varies from 90 to 160ft thick. Granitoid gneisses of probable Archean age and paragneisses of the Wollaston Group underlie the deposit. An easterly dipping thrust fault transects its length.The deposit is typical of the ""unconformity-type"" uraniumnickel deposits of the Athabasca Basin. Observed features fit well with the ""diagenetic-hydrothermal"" model for such deposits, as envisioned by Hoeve and Sibbald (/978)."

Jan 1, 1980

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By PETER O. SANDVIK

The Cargill deposit, located 32 km south west of Kapuskasing, Ontario, was discovered by International Minerals and Chemical Corporation in 1975 and has been evaluated through an extensive program of drilling, chemical analyses, metallurgical tests and engineering and economic studies. The Cargill alkalic complex, comprising mainly carbonatite and pyroxenite-amphibolite rocks, was intruded into the rift system of the Kapuskasing magnetic-gravity high. Weathering and leaching under assumed temperate to cool climatic conditions plus faulting, shearing and/ or initial petrographic variations within the carbonatite developed a small, locally confined karst system. This resulted in a thick enriched leached carbonatite zone capped by troughs and sinks, and filled with a residuum of apatite, goethite, clay and other minerals. Residuum thickness ranges from nonexistent on ridges to 170 m in troughs and sinks. Apatite values are 5 to 15% in fresh carbonatite, 20 to 40% in leached carbonatite and 20 to 98% in residuum. A tentative open-pit mine designed for preliminary feasibility studies is estimated to contain 62.5 million tonnes averaging 19.6% P20 5.

Jan 1, 1984

By F. Urekar, R. B. Pankhurst

"Air spaces and air gaps in an explosives column are known to allow greater distribution and cushioning of explosive energy from the rock mass. This energy distribution is enhanced if the explosives ' gases can be confined in the borehole for as long as possible by plugging and stemming above the air space.Power Plug is an inflatable plug which can seal a borehole at any point to separate the stemming from an air gap and explosive toe load.IntroductionThis paper will discussion-going work by C-I -L Inc. and operators of two open pit mines to study the results of using Power Plugs:I. Pit wall stability - the authors have found the Power Plug effective for wall control blasting in open pit mines.2. Selective mining of coal seams - the authors work shows the Power Plug allows mining selective coal seams by predrilling underseam waste wedges.Pit Wall StabilityWall stability in an open pit mine is essential for safety. Good wall stability can be achieved with wall control blasting techniques which cushion the effect s of the explosives charge by decoupling the charges from the borehole wall. The usual method of decoupling a charge in a large-diameter rotary borehole is to load the explosives in tubes (Fig .I) . We now believe the air deck system is effective in sea ling a borehole above the explosive charge to create an air deck within the borehole which will cushion the blast.In a linear decoupled charge, an air annulus surrounds the explosives charge and cushions the effects of detonation genera ted gases on the pit wall. In an air deck, i.e. with the hole plugged at the collar, the gases genera ted by an explosive toe load are sealed in the empty borehole column. After a period of time, these trapped gases produce radial cracking between holes along the entire length of the borehole.It is common practice to employ de coupled explosive charge columns in the borehole to limit blast damage to surrounding rock. The exact mechanism of energy transfer in such blasts, however, is not well understood. Interruption of the continuous explosive column in a borehole by means of stemming, or air decks, may also be viewed as another form of decoupled blast. Decoupling of the explosive charge from the borehole wall affects both explosive energy release and explosion pressure developed in the borehole."

Jan 1, 1988

By Ki-Bok Min, Bona Park

"In spite of the applications of DEM models to emulate the elastic modulus, Poisson’s ratio and strengths of isotropic rock in laboratory scale, extensions to anisotropic rock and larger engineering scale still have many challenges to overcome such as robust verification and validation against observed field case. In this study, a discrete element modeling was performed in order to represent a transversely isotropic rock such as shale, and the upscaled model was applied to foundation and borehole problems using PFC2D. The applicability of the upscaled rock mass model was verified by an analytical solution. The DEM modeling of stress redistribution induced by an applied surface line load compares well with Boussinesq’s isotropic solution and anisotropic solution given by Bray. The borehole model with a circular opening under biaxial stress was compared with both isotropic and anisotropic solutions resulting in good agreement. The abilities of DEM model to investigate the micromechanisms accounting for complex macroscopic behaviors and to predict the macroscopic behavior are discussed.The results demonstrate that DEM modeling has the potential to be applied to anisotropic rock mechanics problems on larger engineering scales such as wellbore stability problems especially in shale formations. Furthermore, the effect of anisotropy modeled through this study may be able to explain failure behavior of anisotropic rock encountered frequently in real cases.INTRODUCTIONAnisotropy is prevalent in various types of rocks, especially in shale that contain a set of parallel bedding planes. These weak planes in various forms are sources of large deformation and low shear strength and contribute significantly to the anisotropic behavior of rocks (Amadei, 1996; Cho et al., 2012; Kim et al., 2012). As elastic and strength behavior of anisotropic rock is substantially different from that of isotropic rock, proper consideration of anisotropy is of great importance. There is extensive of experimental evidence showing the anisotropy of shale. Niandou et al. (Niandou et al., 1997) analyzed the plastic deformation and failure mechanisms of Tournemire shale were highly dependent on the orientation of bedding planes. Cho et al. (Cho et al., 2012) presented various deformations and strengths of Boryeong shale obtained from laboratory experiments. Fjaer and Nes (Fjaer and Nes, 2013) performed uniaxial and triaxial compressive strength tests using Mancos shale, and they observed that the shear sliding along the planes of weakness before the occurrence of a major failure can reduce the strength of anisotropic rock. The recent research has demonstrated that the anisotropy of rock is an important consideration in rock engineering."

Jan 1, 2015

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006