Search Documents

By L. A. M. Castro

As Canadian mines progress to greater depths, magnitudes of induced stresses increase, becoming high enough to cause rock mass damage and failure during excavation. In addition, depending on the orientation of key geological structures in relation to the in-situ stresses, induced shear loading can be developed on these structures, creating the potential for: a) remobilization of existing geological structures, b) formation of new seismically active structural zones, created through rock mass damage and coalescence along such structural zones, and/or c) interaction between existing and newly created structures. Numerical analyses were carried out to investigate four possible factors that might cause fault slip on controlling structures, namely: (a) unclamping, (b) day-lighting, (c) stress rotation and (d) pillar shear. Application to an underground mine in the Sudbury Basin allowed verification of these factors and the proposal of two alternative mine planning methods to limit fault slip on key structures: (1) pillar clamping and (2) stope sequencing.

May 1, 2009

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

By F. M. Makarinsky

"This paper describes the conversion of conventional froth flotation cells to open-trough type bank cells, with 'buried' vertical metal partitions. These changes have resulted in: total froth removal along the full length of each bank of cells; extended flotation cell retention times; and has extended the life of the metal components, particularly towards the upper flotation cell areas.INTRODUCTIONOver the past twenty years, the flotation cells used at Falconbridge Limited, Sudbury operations concentrators, have gone through major physical changes. The various concentrators generally started with 100 cubic foot Denver Sub 'A' flotation cells. From these units, we progressed to 'converted' DR units, and/or Denver DR units, if purchased new. (Figures 1, 2, 3)In 1980, the Strathcona concentrator started to pay more attention to the 'front end' rougher flotation cells. Initially, the converted DR flotation cells had 'cut-outs' removed (Figure 4) at all upper vertical cell partitions, towards the ff9th lip areas, in order to get additional froth removal."

Jan 1, 1985

By J. Olsson

The paper describes and discusses the use of stainless steels for leaching plants emphasising the duplex family, i.e., austenitic-ferritic stainless steels. This group has generally twice the proof strength of the more common 300-series austenitic grades, which implies possibilities to reduce the gauge at construction of pressure vessels and atmospheric tanks and vessels and thereby possibilities to reduce the weight. The duplex grades have also higher surface hardness resulting in better resistance to mechanical wear, i.e., abrasion and erosion corrosion. The lower contents of nickel and molybdenum imply lower cost and a more stable price considering the present market situation for these alloying elements. Corrosion data from laboratory and pilot plant tests, as well as examples of applications of duplex and highly alloyed austenitic grades, are presented. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By D. D. Campbell

"The Port Radium mine of Eldorado Mining and Refining Limited lies on the western tip of a large peninsula midway up the east shore of McTavish Arm, Great Bear Lake, about 30 miles south of the Arctic Circle. The mine is serviced by air, 950 miles from Edmonton, and by water, 1,380 miles from Waterways, Alberta.The veins were found, and the copper and cobalt minerals in them reported, by J. MacJntosh Bell of the Geological Survey of Canada in 1899. The veins were investigated by Gilbert Labine and E. C. St. Paul in 1930, and as a result of their work the Eldorado mine was brought into production in 1934. It produced silver and radium ores until 1940, at which time, as the silver orebodies had been mined out and the market for radium was negligible, it closed down. Early in World War II the need for uranium for the Manhattan Project was emphasized, and the mine was reopened in 1942. As a security measure Eldorado Mining and Refining was created a Crown company in 1944. The Port Radium mine has continued to be one of Canada's principal producers of pitchblende concentrates, and to date has about 25 miles of underground workings developed on fourteen levels.Regional GeologyThe general geology of the McTavish Arm area was mapped by D. F. Kidd in 1932 on a scale of one inch to four miles. A great deal of more detailed work has since been done by geologists of the Geological Survey and of Eldorado. The entire area at the end of McTavish Arm lies within the Precambrian Shield immediately east of its western margin. Most of the area is underlain by granitic masses which have intruded a sequence of late Precambrian sediments, volcanics, and hypabyssal intrusives. The pre-granite rocks now occur in extensive, irregular patches and pendants within the granite. Pitchblende deposits have been found in the district in all rock types, but the most favourable host rocks are the cherty sediments of the lower Echo Bay group."

Jan 1, 1949

By Z. D. Hora

Sedimentary phosphate-bearing rocks are found over a considerable area of so utheastern British Columbia that extends from Fernie east to the Alberta-British Columbia boundary and from the International Boundary northward to the headwatei: s of the Elk River. Phosphatic beds occur at the following four stratigraphic levels: 1. lower part of the Banff-Exshaw sequence of Mississippian age; 2. lshbel Formation of Permian age; 3. base of the Fernie Group of Jurassic age; 4. belemnite bed within the Rock Creek Member of the lower part of the Fernie Group. To date, considerable tonnages of phosphate rock have been proven in the area. However, no commercial production has been initiated because of a relatively low P2O5 grade. Data on assays and thicknesses of the phosphatic beds are in part recalculated from the paper by Telfer (I 933) and in part from assessment reports filed at the British Columbia Ministry of Energy, Mines and Petroleum Resources.

Jan 1, 1984

By John Oxenford

There are currently two operators producing oil from the surface-mineable portions of Alberta?s oil sands (Syncrude Canada Ltd. and Suncor Inc.) and two other companies are proposing to enter the industry (Albian Sands in 2002 and True North in 2004). Tailings from the two current oil sands plants contain approximately 220 000 tonnes per year of recoverable TiO2 and approximately 80 000 tonnes per year of recoverable zircon. This represents approximately 6% of the world?s TiO 2 consumption and approximately 9% of the world?s zircon production. With the commissioning of plants by Albian Sands and True North, and the announced expansion of plants by Syncrude and Suncor, it is expected that these tonnages could quadruple in the next ten years. All of these operators have at least 50 years of reserves even at these expanded production rates. The occurrence of heavy minerals in Alberta?s oil sands has long been known and is well documented in the literature. There have been a number of attempts to produce market-grade products from this resource and the results of this work have been quite mixed. Typically, researchers have used the normal mineral dressing techniques of the industry and have found the mineral assemblage does not respond to these techniques all that well. This has led to the widelyheld suspicion that there must be some difficult metallurgical problems associated with this resource. There are three main problem areas that have created difficulties for previous researchers: 1) The bitumen coating on the sand grains; 2) Secondary mineralization such as pyrite, siderite and calcite 3) A high proportion of aluminosilicates (approximately 25%) that have the same gravity, electrostatic and magnetic properties as other minerals in the heavy mineral suite. Recent work by Lakefield Research shows that these problems can be largely overcome with some novel approaches. The bitumen can be removed by washing with a solvent in the presence of a demulsifier. The pyrite can be removed by flotation. And the titanium and zircon minerals can be separated by selective flotation followed by conventional electrostatic and magnetic separation.

May 1, 2001

By E. Ferguson

In evaluating refractory designs for cast house applications, thermal calculations are frequently performed to determine cold face shell temperatures, temperature profiles and metal freeze plane locations within the refractory layer, and heat loss in the steady state condition. A problem arises when looking at molten metal transport crucible designs in that these structures are usually operating under non-steady state conditions throughout their production cycle. Because the molten metal temperature varies with time, and material properties such as thermal conductivity are temperature dependant, mathematical solutions are at best... complicated. This paper presents a relatively simple, iterative solution, that can be set up on a standard computer spreadsheet program, to calculate heat transfer in non-steady state conditions. These calculations can provide curves for (1) molten metal temperature vs time and (2) cumulative heat loss vs time, given variable starting conditions, to aid in the evaluation of molten metal transfer crucible refractory designs.

Jan 1, 2004

By K. Koyama

As a study to establish a new energy-saving copper recycling process, the copper deposition at a cathode and oxidation of copper(I) at an anode from ammoniacal alkaline solutions containing Cu(I) or Cu(II) were investigated in order to examine the feasibility of electrolysis in this solution.. The current efficiencies were greater than 95% in the current density range of 200 to 1000 A m-2. The current efficiency decreased with the increasing Cu(II) concentration and temperature. In the batch-type electrolysis at the anode, during the initial stage, the current efficiencies were 100%, and the anode potentials ranged from 0 to 0.15V vs. SHE at a current density of 100 A m-2. During the subsequent stage, the current efficiency decreased with time, and the anode potential was around 1.35V vs. SHE where oxygen evolution at the anode surface was observed. As a result, the present electrolytic method can be the core technology in the said copper recycling process.

Jan 1, 2007

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016

By S. C. Tadolini

"Roof bolts are the primary means of roof support in underground mines in the United States. Presently, post installation loads are measured on about 10% of the expansion anchor and combination bolts by using standard torque wrenches that Unit the accuracy of the measurements to about ±30%. No system has been available for measuring the loads generated on full-column resin grouted bolts. Mine roof bolts are long, slender, non-uniformly sized, roughly forged, and placed in a corrosive environment, creating obstacles for researchers trying to utilize ultrasonic reflection techniques to measure strain. A complete measurement system has now been developed by the U.S. Bureau of Mines, Denver Research Center. This system is being used successfully in determining loads measured on expansion anchor and combination bolting systems, examining the transfer mechanics of full-column, resin-grouted bolts, and measuring loads generated on bolts in an underground roadway support system.IntroductionMillions of roof bolts are used each year to provide structural support in underground U.S. metal, non-metal, and coal mines. Approximately 45% of the bolts used are expansion anchor, 45% are resin-assisted combination or full-column resin-grouted, and 10% are friction anchored. The effectiveness of these bolting types is dependent on a number of factors including rock density, bolt length, in situ stresses, rock properties, bolt pattern, installation tension, etc. When implementing expansion anchor and resin assisted combination bolts , installation and post-installation tension, or load, is a major determinant of support quality and subsequent behaviour of the reinforced roof. The method by which these systems carry roof loads is well understood and documented(1,2).The importance of these installation and long-term bolt tension measurements is well recognized and are required in the federal government regulations(3). A statistical sample of the bolts, lout of 4 during installation and lout of 10 inby the last open crosscut, is required to be measured using current torque wrench technology. The disadvantages of this system are the disturbance and weakening of the anchorage and limitations of accuracy to approximately ± 30%. The method by which resin-grouted bolting systems carry roof loads is much less understood, mainly because testing procedures used to evaluate point-anchor systems are not effective on resin-grouted bolts.Due to these problems, the U.S. Bureau of Mines designed a measurement technique that provided a highly accurate, low cost-per- bolt system that led to the development of ultrasonic pulse echo instrumentation. The original system was designed to measure the tension only on expansion anchor bolts. Recent developments and system modifications have permitted measurements on resin-assisted and full-column resin-grouted bolts. The use of these types of support systems has been increasing steadily in underground coal mines.The development of this instrumentation has provided laboratory and field results that help to explain the mechanics and relationships between the applied loads and the interaction between the grouted bolt system consisting of the bolt tendon, grout, and rock."

Jan 1, 1990

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Several studies conducted recently have shown that molybdenite flotation from Cu-Mo ores is adversely impacted in sea water at pH >~ 10.0 irrespective of the pH modifier; under the same conditions Cu sulfide flotation is relatively unaffected. This has been attributed to the presence of Mg2+ ions and their hydrolysis products in the sea water which adsorb and precipitate on molybdenite surfaces as Mg(OH)2. However, why and how Mg(OH)2 impacts only molybdenite flotation in the complex flotation pulps containing a multitude of minerals is not understood. The work presented in this paper probes the interface and interphase regions near the edge and basal planes of natural molybdenite (MoS2) in aqueous solutions and flotation pulps, particularly in the presence of copper ore pulp and added Mg2+. Differences in interaction of metal ions and their hydrolysis products (Mg2+, Mg(OH)+) were measured on the two faces of this anisotropic mineral. How those differences relate to molybdenite floatability and the impact of aqueous solution chemistry are discussed.INTRODUCTIONWater resource management is an important sustainability challenge in mineral processing. In view of the shortage of fresh water in many parts of the world, mineral processing plants are evaluating alternative sources. Seawater flotation has received much attention recently and there have been several important studies reported in the literature, particularly for the processing of Cu-Mo ores (S. Castro, 2012; S. Castro, Rioseco & Laskowski, 2012; S. Castro et al., 2012; Laskowski & Castro, 2012; Ramos, Castro & Laskowski, 2013; S. Castro & Laskowski, 2013; Laskowski, Castro & Ramos, 2013; Nagaraj & Farinato, 2014; S. Castro, Uribe, & Laskowski, 2014; Veki, 2013). The main conclusions from these studies on Cu-Mo ores in seawater at elevated pH were: a) flotation recovery of Cu sulfides is either unaffected or only marginally reduced, b) molybdenite recovery is adversely affected in seawater at pH values necessary for rejecting pyrite (i.e. pH > 10 to 10.8 depending upon particular system), and c) the precipitation of Mg2+ in seawater as Mg(OH)2 is responsible for the adverse effect on Mo flotation. In order to further investigate the individual effects of Mg2+ and Ca2+ on molybdenite depression in Cu-Mo ore flotation, Nagaraj & Farinato (2014) conducted flotation tests wherein individual metal ions were spiked into tap water during grinding of Cu-Mo ores. They showed the strong adverse effect of Mg2+ addition on Mo recovery and, to a lesser extent, on Cu recovery when pH > 9.5. Under similar conditions, Ca2+ had virtually no effect on either Cu or Mo sulfide flotation. Figure 1 below shows the previous results for Cu- Mo ores in tap water and the effect of addition of Ca2+ and Mg2+ ions. Note that in seawater the adverse effect of Mg2+ on Cu recovery was much smaller than that in tap water (Nagaraj & Farinato, 2014; Figure 4a and 4b and Table 4 therein)."

Jan 1, 2016

By Y. H. Hatzor

"This is an extended abstract for a keynote lecture delivered by the author during the 2015 ISRM congress in Montreal on the application of the numerical discontinuous deformation analysis (DDA) method in rock mechanics practice. Due to the large scope of the topic this lecture will focus on studies performed by the rock mechanics group at Ben-Gurion University, alone or in collaboration which other research groups, and is not intended to provide a comprehensive review of everything that has been done on the subject worldwide during the past two decades. A forthcoming textbook (Hatzor et al., in preparation) will attempt to provide such comprehensive coverage.DDA has been developed by Dr. Gen-hua Shi while he was doing his PhD studies under the supervision of Professor R. E. Goodman at U. C. Berkeley (Shi, 1988). Dr. Shi has invented a new numerical discrete element method which provides a solution for dynamic deformation of block systems, hence its applicability to rock mechanics practice. The method is similar in essence to the finite element method in its implicit formulation of the time integration scheme and where in every time step the minimum potential energy of the entire system is sought, but here every element is a finite block with six degrees of freedom. The blocks are assumed to be stiff (simply deformable) so that most of the energy is consumed by slip along pre-existing discontinuities, the frictional resistance of which is assumed to obey the Coulomb-Mohr failure criterion for rock joints. The greatest advantage of DDA over alternative numerical discrete element methods is its robust area (volume) integration which ensures great accuracy even when the blocks are of irregular shapes, including non-convex blocks which may contain holes. The greatest disadvantage is the necessity to solve in every time step very large matrices of unknowns, imposing great CPU demand when the block system involves a large number of blocks. Another disadvantage is the sensitivity of the solution to the choice of the penalty parameter which is implemented in DDA in the form of stiff springs that are attached to contacts once detected automatically.The inherently dynamic formulation of the DDA method lends itself to solution of dynamic problems in rock mechanics. Dynamic analysis with DDA can be performed in different ways corresponding to different rock mechanics problems and loading conditions. Three main classes of loading conditions which are relevant to rock mechanics applications are discussed here: 1) dynamic loading of a single bock which rests on a stationary foundation, 2) response of a block to dynamic loading of the foundations, 3) wave propagation through a block system.The most common approach is to introduce the dynamic force to a specific block in an otherwise fixed block system and check the resulting deformation, typically the time dependent displacement or rotation of the loaded block. This approach is particularly useful for dynamic rock slope stability studies when a stability of a specific rock block against earthquake vibrations is in question. The first 2D-DDA benchmark test of this approach was performed by Hatzor and Feintuch (2001) who introduced harmonic acceleration functions into a block which rests on an inclined plane. The analytical solution proposed for this problem by Hatzor and Feintuch (2001) was later generalized by Kamai and Hatzor (2008). The first 3D-DDA benchmarking for this approach was presented by Bakun-Mazor et al. (2012) who studied single and double face sliding of blocks which rest on stationary foundations and subjected to harmonic input acceleration functions."

Jan 1, 2015

By Jeremy D. Glennon

A number of exciting challenges, opportunities and unanswered questions remain concerning the chemistry, geochemistry, medical, industrial and analytical applications of gold and its compounds.1 Among the challenges presented is the need for extraction methods for gold, at process and indeed analytical scales, that avoid the use of organic solvents or hazardous reagents. Extensive environmental contamination has occurred in the Brazilian Amazon from the mercury-gold amalgamation process. Major problems with the cyanidation process are the relatively slow dissolution kinetics and the health and environmental problems associated with it. With innovation and technical changes, a cleaner way for solubilising and extracting this versatile precious metal can be found. This cleaner future may lie in supercritical fluid science. Interestingly, geochemical studies of gold solubility and speciation in hydrothermal solutions have highlighted the importance of supercritical conditions and sulphur species in the deposition of gold in natural environments. Gold solubility in supercritical brines is far higher than previously supposed while interest in the high content of carbon dioxide in the mineralizing fluids is growing. 2,3 In recent years, also, there has been a tremendous amount of attention paid in analytical chemistry and in industry, to the area of supercritical fluid extraction (SFE) of organic and metallic species. 4 This interest has been fuelled by the introduction of more stringent environmental control and the subsequent need for cleaner solvents and processes to replace established ones. Carbon dioxide is the substance of choice for SFE because of its moderate critical parameters (Tc = 31oC, Pc = 73atm), inertness and availability in pure form. It is an excellent extraction medium for non-polar and moderately polar species, and with careful ligand design, it can be used for analytical and process scale metal extraction from solution and solid phases. In general, the dissolution of a metal in supercritical CO2 (sc-CO2) requires that the charge on the metal ion be neutralised on complexation by the ligand or through a form of ion pairing (analogous to the situation where metal ions are extracted into organic solvents, such as methyl isobutyl ketone or toluene). In this way, then, many chelating agents such as dithiocarbamates and hydroxamic acids have been utilised to extract metal ions such as Cu and Fe into sc- CO2, the process greatly enhanced by the use of fluorinated ligand derivatives. 5-7 In this review paper, we show that supercritical conditions and complexation with sulphur donor atoms, important in the natural deposition of gold, can form the basis of a clean, eco-friendly chemistry for gold extraction. Analytical scale extractions of gold from a variety of matrices can be conveniently used to assess the efficiency of any new proposed ligand.

Oct 1, 2003

By G. Guiglionda, A. Deschamps, F. De Geuser, M. Langille, B. J. Diak

"Increased demand for light-weighting in passenger vehicles has created a need for strong, light, ductile materials to be used in body-in-white applications. The AA6xxx-series of aluminum alloys are suitable candidates meeting most requirements but can fall short of the formability demands of designers, necessitating an understanding of what controls the formability in this alloy series. This work examines the effect of copper alloying in AA6xxx on the pre-ageing and natural ageing responses of the microstructure and mechanical properties. The changes in microstructure observed by differential scanning calorimetry and hardness testing are related to the work-hardening and strain-rate sensitivity parameters for these alloys measured by tensile testing. An observed asymmetry in the measured strain-rate sensitivity associated with increasing versus decreasing strain rate changes suggests that a different mechanism operates for the two conditions. It is postulated how this asymmetry in strain-rate sensitivity will impact the necking and ductility behaviour of these alloys.INTRODUCTION The widespread use of AA6xxx series alloys in the form of sheets has provided the need for a more thorough understanding of the complex interactions between composition, processing, resulting microstructure and ultimately, the mechanical properties of the alloys. Conventional industrial practices involve the production of rolled AA6xxx sheet (typically 1 mm thick) to be used for body-in-white (BIW) applications for auto body panels (Hirsch, 2004, 2014). The final metallurgical step prior to the shipment of these panels to manufacturers involves a solution heat treatment (SHT) reverting the ageing products of the alloys into solid solution and the product is then shipped to the customer. During this shipping time and while sheets are waiting to be used, the natural ageing (NA) process occurs whereby the strength of the alloys increases resulting in reduced formability. This can result in a product that is unable to meet the formability demands of the automotive manufacturer. As a result, industry has moved towards performing pre-ageing (PA) treatments to prolong the “shelf-life” of the material prior to it having insufficient formability. Once formed into BIW panels, the parts are then painted and subsequently undergo the paint curing heat treatment which consists of a short period of time at medium temperature, typically 20 minutes at 170–190°C. This short artificial ageing (AA) treatment, known as the paint bake (PB), provides additional strength and improved dent resistance for the material, but reduced formability. The PB result is strongly dependent on the PA treatment performed prior to the forming operation. Furthermore, the addition of copper (Cu) to a base Al-Mg-Si composition is known to increase the alloy’s strength. The goal of this work is to study the effect of Cu on strength, strain hardening, and strain-rate sensitivity (SRS) of these alloys, to understand the strength-formability compromise, for two separate heat treatment schedules; one including and one excluding the PA treatment, both followed by NA."

Jan 1, 2018

By Eamonn F. Maher

Superconductivity is one of the most remarkable scientific phenomena ever investigated. It is the phenomenon whereby some materials exhibit zero resistance to the passage of an electric current when cooled to low temperatures, and requires a quantum mechanical explanation. Four Nobel prizes in physics have been awarded specifically on the subject of superconductivity, with many more enabled by superconducting technology. For example, particle beams are generated in accelerators and manipulated in ?particle beam lines? in the ?Big Physics? projects around the world eg. at CERN, Geneva, leading to major discoveries in fundamental particle physics. Similarly, at the JET Propulsion laboratory near Oxford, U.K, controlled nuclear fusion has been demonstrated, and magnetic containment of plasmas is key. In the chemical and biological sciences high field NMR spectroscopy has become indispensable for examining organic matter, revealing the mysteries of the workings of cells, genetics, and in the development of new polymers and pharmaceuticals. With all these very advanced uses for superconducting magnets, it is easy to forget that superconductivity is big business, not just a scientific curiosity. MRI (Magnetic Resonance Imaging) superconducting magnets, the key component of high resolution body scanners, use approximately half of the world?s superconducting wire ? the other half being mostly used in accelerator magnets. The MRI market is about 3 billion dollars per annum, and one MRI magnet uses 200km of wire. New applications for superconducting magnets are now appearing including ?Catheter steering?, enabling much shorter timescales for life-saving brain tumour removals and ?Functional MRI?, a whole new area in patient diagnostics. Whilst the use of low temperature superconductors (LTS) is now well established commercially in superconducting magnets and niche electronic applications, the application of LTS in electric power distribution and transport has been very limited to date. It is now more than fifteen years since the so-called High Temperature Superconductor (HTS) materials were discovered: these can be operated at liquid nitrogen temperatures rather than liquid helium temperatures. However, materials processing and scale-up issues have prevented their widespread use, and in particular the required price/performance criteria are only beginning to be reached except in certain niche markets. BSCCO (Bismuth Strontium Calcium Copper Oxide) tapes up to one km long are now readily available, and have been demonstrated in high current cables for power distribution networks, but the general consensus is that 1) it is difficult to reduce the price much further because of the silver matrix required and 2) in applications where coils are required eg. motors, generators, transformers etc the properties of BSCCO are rather poor because of the critical current dependence on magnetic field. Magnetic fields are always associated with coils and windings, and such fields are of course fundamental to the operation of all electrical machines. YBCO (Yttrium Barium Copper Oxide) however, has good characteristics in field and for the last few years there has been intensive research and development costing several tens of millions of dollars worldwide into the scale-up of production of so-called ?coated conductor?. This ?second generation? tape can be produced by any of many different film deposition techniques, with more or less success for short lengths, but as yet it is unavailable in lengths more than a few tens of metres.

Oct 1, 2003

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By N. Afrin

The microstructure and tensile properties of AZ31B-H24 magnesium (Mg) alloy after friction stir welding (FSW) were evaluated. The grain size was observed to increase from approximately 5 µm to about 9 µm after FSW. The obtained Hall-Petch type relationship showed a strong grain size dependence of the hardness values. While the FSW led to about half of the yield strength of the base magnesium alloy, the ultimate tensile strength after FSW could reach about two thirds of that of the base alloy. The hardening capacity of the FSWed samples was about twice of that of the base alloy. The strain hardening exponent of the base alloy was found to be about 0.1 whereas it became larger than 0.3 for the FSWed samples. After yielding the base alloy showed a high initial and almost constant work hardening rate, corresponding to linear hardening stage II, followed by stage III with a decreasing hardening rate. Stage II linear hardening was observed to be absent in the FSWed samples.

Jan 1, 2007