Search Documents

By J. R. MacDonald

MINING literature contains very few descriptions of operations producing as little as 25 to 30 tons of ore per day. The purpose of this paper is to discuss the gradual development of a mining method for such a small-scale operation at the No. 2 mine of Central Patricia Gold Mines, Limited, and in doing so to review several systems of stoping applicable to narrow ve1ns. MAIN ECONOMIC FACTORS TO BE CONSIDERED (1) Overhead.-The outstanding feature of most mines operating on a single narrow vein is chat of small daily tonnage. The reason for this low output can be readily understood. The strictly limited ore-reserves present a condition unfavourable for a policy of large initial expenditures, with the result that the capacity of the plant provided must be governed by the? amount of ore in sight at the time when mill construction is planned. This is immediately reflected in the cost per ton, there being relatively few tons over which to distributed the more or less static charges, such as hoisting, heating, supervision, administration, pre-production expenses, and other write-offs. (2) Development.-In mining this type of orebody, the main factor contributing to high costs is unquestionably the small tonnage of ore made available by a given amount of development. Thus, for example, from the data tabulated below it can be seen chat, assuming a 12-in. vein and a drifting cost of $9.00 per foot, the development charge for this item alone would be 71 cents per ton. Add to this the charges for raising, cross-cutting, shaft-sinking, and pumping, besides charges arising from development in waste, and the figure will be very considerably higher than 71 cents.

Jan 1, 1941

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public's awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By A. Atef

Vulnerability is a measure of the extent to which a community, structure, services or geographic area is likely to be damaged or disrupted by the impact of particular hazard. Current asset management practices focuses on studying factors that affect performance of isolated infrastructure networks and model a set of actions to control the expected performance of these networks. This approach ignores the underlying spatial and functional interdependencies among these infrastructure networks and their vulnerability. The purpose of this paper is to introduce a new method that recognizes the effect of spatial and functional interdependencies on vulnerability rating of water, sewer and road networks. The proposed method consists of: 1) risk assessment model, 2) interdependency assessment model and 3) vulnerability assessment model. The risk model is composed of two modules: 1) water and sewer risk module and 2) road infrastructure module. The water and sewer risk module will cluster these assets into three risk categories based on environmental, social, operational and economical factors. The road infrastructure module will cluster road assets into three risk categories by using rational factorial technique based on road type, serviceability index, traffic load, and freeze and thaw index. The interdependency model will deploy the risk ranking to perform geospatial analysis in ArcGIS which results in determining the interdependent layers of waters, sewers and roads. The vulnerability model will deploy fuzzy neural networks technique to determine the vulnerability rating based on spatial and functional interdependencies. The fuzzy neural networks are utilized to overcome the lack of historical data and incorporate experts? preferences for establishing the knowledge base for vulnerability assessment. The expected contribution of this framework is to aid decision makers in understanding the interdependencies between civil infrastructure assets and to which extent such interdependencies can compromise assets performance.

Aug 1, 2013

By Michael Farley, Paul Dufour

"Relationships, Partnerships,Marriages (RPM)RPM has a nice musical ring to it, but it is in fact synonymous with science and technology, university-government -corporate links and the more genera l issue of university roles in technology development. Pick up any report on one of these issues, and chances are that you will find one of these key words in the title. Play it, and you will find that the revolutions per minute are increasing. It is difficult to keep track of the wide variety of institutional experiments now developing in Canadian universities in attempts to marry science and research with technology commercialization and technology transfer.Why is the role of Canadian universities in this matter important? There are at least five good reasons:1. It is important because these knowledge institutions are producer s of scientific research, a major component of technology. Today the gap between the two is rapidly shrinking.2. It ' is important because Canadian industry is turning to universities for tech no logy development and new knowledge. Figure 1 shows that universities are becoming an important source of technology available to Canadian firm s; more important in fact than government. Figure 2 illustrates this trend more graphically in showing that university collaboration is one of the preferred methods of industry participating in co-operative R&D efforts:3. The role of Canadian universities in technology development is also important because the provincial and federal governments have embarked on various programs and policies for promoting the use of technology and science for economic benefit. Universities are playing an increasing role here. For example, the submission of IDEA Corporation (a venture capital operation funded by the government) in Ontario to the Bovey Commission on the Future Development of Ontario Universities clearly spelled out its ideas for commercialization of university research in Ontario . Among other things, the brief suggested that Ontario's universities need to be better equipped to transfer technology, and the reward structure in university research must incorporate industrial interests."

Jan 1, 1986

By W. A. Grell

"The oxygen meter has been in use at MacLeod Cockshutt Gold Mines for over a year, At MacLeod about 200 tons per day of reground concentrate containing roughly 10% pyrrhotite and 20% pyrite is cyanided in four 181 x 18' Dorr agitators. A survey by the Department of Mines showed that oxygen content of some of the agitators was rather low. Experience with our oxygen meter indicates that the oxygen content must at times have been too low for good gold dis solution.We have found that in winter, when pulp temperatures drop to about 50° F, oxygen saturation in the agitators is not difficult to maintain. In summer, however, when pulp temperatures rise to 70or 75°F, the oxygen content will drop very readily. It was found that a high oxygen content can be maintained readily if the pulp is sufficiently dilute. Thus at 50° F, a pulp of specific gravity 1. 75 i.e., about 55% solids, will saturate; but at 70 or 75° F, the specific gravity must be decreased to 1 .45, equivalent to about 40% solids, in order to maintain saturation. Very thick pulps, such as thickener underflows, are noticeably difficult to saturate in the laboratory, and lose their oxygen rapidly.Clear solutions, on the other hand, absorb oxygen readily and hold it. The primary thickener overflow, before agitation, is 100% saturated; after storage of 3 to 4 hours it is still 100% saturated at re clarifier tank. Barren solution after spraying in a launder is 100% saturated.We have not yet attempted to determine what percentage saturation is necessary for good extraction, but it is known that there is a point at which extraction decreases rapidly. So far, the measures required to maintain over 80 or 90% saturation have coincided with measures required to hold the reducing power to the point believed necessary."

Jan 1, 1964

By Alfredo Bambaren

First Encounters between Communities and Mining 1. Importance, meaning and process 2. Antamina?s study case 3. ?Self-organization? theory (NLP) 4. The story we tell, the values we live 1. Importance, Meaning and Process ? First encounter stays in mind as a model. ? First encounter means foundation. ? First encounter builds the story.

May 1, 2010

By Staff

Introduction The Hedley mine, perhaps better known as- the Nickel Plate mine, is one of the outstanding properties of southern British Columbia. Discovered in 1898 by Woollison and Arundell, prospectors, the property was bonded in 1899 to M. K. Rodgers for the Marcus Daly Estate, of Butte, and development was started the same year. From the high grade of the ore outcrop, and its colour, due to oxidation of the arsenopyrite, it was not difficult to open up and trace the showing. The Nickel Plate ore-shoot, which apparently had been easy to follow on surface, was more difficult to trace underground. In 1903, prospecting on an adjoining property, the Sunnyside, showed commercial ore at surface, but it was only after two years' work that the ore-body was defined and shipments started. From this property, $1,200,000 have been taken out. Prospecting was also carried on on the IXL, Climax, Copper Cliff, Mound, Bulldog, Exchange, Silver Plate, Gold Plate, and other properties, all of which had surface showings, but up to date only the Nickel Plate, Iron Duke, Morning, and Sunnyside have produced commercial ore. In 1904, the Bulldog looked like a very promising mine, but it failed to make good. In 1905, the Sunnyside No. 1 was in the limelight, but it also failed to make the grade. In 1906, an outcrop on the Sunnyside No. 3 looked interesting. Subsequent work. on this claim produced $840,000, and at the same time ore which yielded $400,000 was mined from the Sunnyside No. 4. In 1908, the Nickel Plate ore-body entered a lean zone and, as the diamond drill failed to give satisfactory results, the Daly Estate, after making a profit of $1,151,000, sold the property to the Hedley Gold Mining Company, Limited, for $760,000, retaining, however, a large interest.

Jan 1, 1929

By A. M. Bell

"Hallnor mine is in the township of Whitney, Porcupine district. To date, its production of gold has been second largest in the east Porcupine field. Ore was discovered in the property in 1936 by diamond drilling in overburdened country. This drilling was undertaken by Noranda Mines following the discovery of ore in conglomerate at Pamour 1 mile to the east.Milling commenced at the Hallnor in June 1938, and to the end of 1945 432,000 oz. gold had been produced from 889,000 tons of ore, giving an average recovery of 0.49 oz. a ton.The West mine of Pamour, the Broulan orebody, and the veins on the Hallnor and Bonetal are all parts of a mile long vein system that has been separated into three sections by cross faulting. In consequence, they could well have been described in one paper. In treating them individually the viewpoint obtained from each may lead to conflicting opinions, and any conclusions advanced in this paper on the general structure should be modified by the conclusions advanced in papers on the neighbouring properties.GENERAL GEOLOGYRock FormationsThe Hallnor orebodies occur within 400 feet of the contact between lavas and sediments, and may lie in either lavas or sediments. The lavas near the ore consist of flows of pillowed andesite and one flow of more acid and less sheared and chloritized lava locally named trachyte. These flows strike east-west and dip steeply. At the surface on the east side of the property the volcanics have been intensely altered to a massive carbonate rock having a north-south thickness in excess of 1,000 feet . This carbonate body extends west across the property with a plunge of 45° (Fig. 1)."

Jan 1, 1954

By Asbjørn Solheim

The service life for aluminium reduction cells is often limited by the cathode carbon, due to preferential wear along the periphery of the cell leading to the so-called "W" wear pattern. The reason for this preferential wear is not well understood. Two mechanisms are suggested in the present paper; 1) non-stationary dissolution of aluminium carbide into a layer of sludge that periodically forms and disappears, and 2) electrochemical formation and dissolution of aluminium carbide within an aluminium carbide layer containing bath-filled pores. The latter mechanism may be related to the high local current density at the periphery of the cathode.

Jan 1, 2011

By Jason A. McLennan

Conditional bias is an infamous problem with estimation methods including kriging. Changing estimation parameters will mitigate, but not remove, conditional bias. The conditional bias of kriging is well understood; however, there is widespread confusion in the literature and among practicing geostatisticians regarding the conditional bias of geostatistical simulation. There is no conditional bias of simulation when the simulation results are used correctly. The correct use of simulation for recoverable reserves estimation is to (1) generate multiple realizations conditional to all available data at a small scale, (2) linearly average all realizations to the chosen block size and (3) calculate the probability of each block being ore and the ore grade of each block. The ?probability of ore? and the ?ore grade? are conditionally nonbiased.

May 1, 2002

By L. Fernandes

A factorial study was performed to investigate the relative effects of temperature, copper concentration and meso-2,3-dimercaptosuccinic acid (DMSA) concentration on the performance of thiosulfate leaching of gold. A total of 24 leaching experiments were performed representing eight unique combinations of high-low levels of the three factors performed in triplicate. All investigations were performed in an electrochemical cell with an electrolyte composed of 0.1 M sodium thiosulfate with a combination of copper (either 0 mM or 1 mM) and DMSA (either 0???or 1µM). All leaching investigations were conducted under open circuit while the electrolyte, which was open to the atmosphere and mechanically stirred, was maintained at either 25°C or 50°C. After 1.5h of leaching the amount of gold in solution was quantified using ICP-MS analysis from an aliquot of the electrolyte. Results indicate that DMSA addition improved gold leaching performance, most notably at 50°C and with addition of copper. Under this unique condition, the quantity of gold in solution was reproducibly and significantly above the average response of all other factors studied.

Jan 1, 2014

By H. Kuboyama

The synergistic effects of polymer additives such as gelatin and polyethylene glycol) (PEG) and Cl- on Cu electrodeposition have been investigated by measuring the polarization curves for Cu deposition, by rotating ring-disk electrode technique and by AC impedance measurements. The cathode potential for Cu deposition was greatly polarized in solutions containing both Cl- and gelatin or PEG, showing evident synergistic effect of polymer additives and Cl- on Cu deposition. The cathode potential was shifted to the less noble direction with increasing the concentration of Cl- in solutions containing polymer additives and showed the maximum polarization at Cl- concentration range between 0.1 and 1 mmol/L. The rotating ring-disk electrode technique revealed that Cu deposition in solutions containing small amounts of Cl- proceeded with initial formation of adsorbed intermediate CuClad. The Cole-Cole plots obtained by AC impedance techniques suggest that the reduction of CuClad is suppressed by polymer additives. The morphology of Cu deposited from solutions containing both PEG and Cl- showed the compacted surface composed of smaller grains due to an increase in the overpotential for Cu deposition.

Jan 1, 2007

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By J. P. Grieco, F. W. Grieco

"Manufacturing of Jaw CrushersOriginIn 1858 Eli Whitney Blake invented the first successful mechanical rock breaker-the Blake-type jaw crusher. Blake adapted a mechanical principal, the powerful toggle linkage system used to transform rotating motion and energy into oscillating mot ion and tremendous compressive forces. Today these same principals apply and the basic Blake-type jaw crusher is one of the leading machines of its class for heavy duty primary crushing service.In 1881 Philetus W. Gates patented a design for a crusher, the forerunner of the modern gyratory crusher which dominated the field from the late 1800s to the early 1900s. In 1910 the largest gyratory crushers built had 48-inch openings. However, about this time the jaw crusher came to life when the Power and Mining Machinery Co. built an even larger sized opening crusher-a giant 84-inch by 60-inch jaw crusher for a trap rock quarry in Pennsylvania. A 24-inch gyratory crusher became the ideal sized secondary machine for this size jaw. From that time on jaw crushers were looked on favourably as primary breakers and lines were brought up to date to parallel the already developed gyratory lines.FunctionMost heavy duty Blake-type jaw crushers work basically the same way. They are ruggedly designed and capable of crushing material in some cases in excess of 80, 000 p.s.i. compressive strength. They are very simple machines with few moving part s and, with the exception of replacement of renewable parts, are relatively maintenance free. It is quite common to have these machines in product ion for 20 to 30 years. The following will de scribe how these machines work. Large-diameter high-inertia flywheels which are connected to the main eccentric shaft, rotate inside a connecting rod type mechanism called a Pitman. It transforms rotating motion into vertical oscillating motion. This vertical motion is in turn transformed into reciprocating mot ion by means of a system of 2 toggles, each connected to the Pitman. The rear toggle is connected to the fixed rear head, and the front toggle is connected to the swing jaw which is hinged at the top of the crusher. With each rotation of the eccentric shaft the swing jaw opens and closes on rock which is fed into the crusher chamber, crushing the rock in a series of bites. These bites, or strokes as the y are called, usually vary between 1/2 inch to 1 1/2 inch at speeds of 120 to 200 strokes per minute. The reduction ratio of feed input to discharge is usually about 8 to I. Output capacities can vary from 100 tons/hour to 1200 tons/hour depending on the size of machine and its discharge opening. Horsepower requirements can vary from 75 hp to 400 hp.The entire crusher chamber is lined with replaceable 14070 manganese steel liner plates. This material is ideally suited for the job since it hardens as it wears during crusher operation. Manganese is also used in the high wear areas at each end of the toggle plates."

Jan 1, 1985

By J. P. Grieco, F. W. Grieco

"Manufacturing of Jaw CrushersOriginIn 1858 Eli Whitney Blake invented the first successful mechanical rock breaker-the Blake-type jaw crusher. Blake adapted a mechanical principal, the powerful toggle linkage system used to transform rotating motion and energy into oscillating mot ion and tremendous compressive forces. Today these same principals apply and the basic Blake-type jaw crusher is one of the leading machines of its class for heavy duty primary crushing service.In 1881 Philetus W. Gates patented a design for a crusher, the forerunner of the modern gyratory crusher which dominated the field from the late 1800s to the early 1900s. In 1910 the largest gyratory crushers built had 48-inch openings. However, about this time the jaw crusher came to life when the Power and Mining Machinery Co. built an even larger sized opening crusher-a giant 84-inch by 60-inch jaw crusher for a trap rock quarry in Pennsylvania. A 24-inch gyratory crusher became the ideal sized secondary machine for this size jaw. From that time on jaw crushers were looked on favourably as primary breakers and lines were brought up to date to parallel the already developed gyratory lines.FunctionMost heavy duty Blake-type jaw crushers work basically the same way. They are ruggedly designed and capable of crushing material in some cases in excess of 80, 000 p.s.i. compressive strength. They are very simple machines with few moving part s and, with the exception of replacement of renewable parts, are relatively maintenance free. It is quite common to have these machines in product ion for 20 to 30 years. The following will de scribe how these machines work. Large-diameter high-inertia flywheels which are connected to the main eccentric shaft, rotate inside a connecting rod type mechanism called a Pitman. It transforms rotating motion into vertical oscillating motion. This vertical motion is in turn transformed into reciprocating mot ion by means of a system of 2 toggles, each connected to the Pitman. The rear toggle is connected to the fixed rear head, and the front toggle is connected to the swing jaw which is hinged at the top of the crusher. With each rotation of the eccentric shaft the swing jaw opens and closes on rock which is fed into the crusher chamber, crushing the rock in a series of bites. These bites, or strokes as the y are called, usually vary between 1/2 inch to 1 1/2 inch at speeds of 120 to 200 strokes per minute. The reduction ratio of feed input to discharge is usually about 8 to I. Output capacities can vary from 100 tons/hour to 1200 tons/hour depending on the size of machine and its discharge opening. Horsepower requirements can vary from 75 hp to 400 hp.The entire crusher chamber is lined with replaceable 14070 manganese steel liner plates. This material is ideally suited for the job since it hardens as it wears during crusher operation. Manganese is also used in the high wear areas at each end of the toggle plates."

Jan 1, 1985

By Robert M. Hopkins, Craig C. Monahan

A corrosion survey was performed on ten selected H-piles which support a reinforced concrete wharf located at Trepassey, Newfoundland. Approximately 900 thickness measurements were taken at twelve different locations in each off our zones on the steel piles: the splash (atmospheric) zone, the intertidal zone, the low tide zone and the submerged zone. Results show that over the 2o-year life of the wharf, corrosion has been most severe in the splash, low tide and submerged zones with average corrosion rates for the flanges of 6.95, 9.45 and 6.86 mils per year (mpy}, respectively, and average corrosion rates for the webs of 5.13, 4.12 and 3.45 mpy, respectively. Minimal attack was found in the intertidal zone where the average corrosion rate was only 1.66 mpy on the flanges and 1.37 mpy on the webs. Such a pattern of attack is frequently observed f or steel piles partly submerged in seawater. The abnormally low corrosion rate associated with the intertidal zone is generally explained as being due to cathodic protection induced by the high corrosion rate in the adjacent low tide zone. Analysis of the corrosion data obtained for the Trepassey wharf would suggest that this explanation might be incorrect. An alternate hypothesis has been brought forward which better accounts for the extremely low corrosion rate observed in the intertidal zones of these piles.

Jan 1, 1990

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By D. Lemieux

A gold bearing pyrite concentrate was treated at the pilot scale for the extraction of gold. Mineralogical analysis of the concentrate identified gold to be mainly present in the form of a solid solution in pyrite. This gold distribution resulted in a poor extraction yield of 55% by direct cyanidation. A piloting campaign including an oxidative pre-treatment by roasting in a fluid bed was followed by treatment with halogens for gold extraction has led to a gold extraction yield of 96.5%. Sulphur removal during the oxidation was very efficient at >99.5% and gold extraction by the halogens was completed within a 1 hour contact time. The piloting was performed on a 300 kg sample and uses a diluted solution of hypohalites as the oxidizing agent for gold extraction. Sulphuric acid was injected in the reactor during the halogens treatment to lower pH to 2. The diluted solution of hypohalites (1-3%) was generated by electrolysis during the piloting campaign in a membrane-less electrolysis cell. The extracted gold was recovered over activated carbon in column and the gold depleted brine was treated for impurities removal and recycled for further gold extraction. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable, the Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.

Aug 1, 2013

By Ian L. Price

Description of the Springhill Coal Field The Springhill coal basin, which lies in the approximate centre of Cumberland county, Nova Scotia, is of Carboniferous age, and forms a syncline plunging to the westward at an angle of 32° at the outcrop but gradually flattening to the dip. It contains several workable seams of varying thicknesses, a generalized section of the measures in descending order from the surface being: [] The 1,114 feet of strata is composed of shales and sandstones, and all of the coal seams mentioned, with the exception of No. 4 and No. 5, have been mined commercially. The coal is said to be the best steam and domestic coal in the Province of Nova Scotia.

Jan 1, 1946

By S. A. Willis

For the past several months 1 have been considering the functions of this Society and its reasons for continuance. The fact that it is now sixty years old indicates that it must have been of value and we all know that it has contributed much that was worthwhile to Nova Scotia and the Maritime Provinces. The question arises: "What is the future of the Society, and how might its activities be altered to suit present-day activities and to be of even greater value?" Let us analyse the various activities in which we are interested and determine which, if any, are of more value than others. First of all, at least once a year we have a two-day convention which constitutes a holiday for the members and their wives. This has always been well planned and has been much enjoyed. Second, there are many social and business contacts made during the meetings and interim meetings. These certainly tend toward better relations and co-operation between the various people concerned. Mine operators meet other mine operators, engineers, people from the education fields, Department of Mines, and so forth. Various sales contacts are made at these meetings which can be of value and use to both the Company selling and the customer. Third, and of greatest importance in any conference, is the exchange of ideas by the members and by authorities from outside, and the presentation of slides and drawings, or actual visits to operations. It is upon this phase that 1 wish to elaborate. These papers are not only presented to our meetings but are generally published in the C.I.M. Bulletin so that members throughout the Dominion have access to them. Many important papers describing new phases of operations have originated through our Society.

Jan 1, 1947