Search Documents

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By S. J. Cook

Outstanding advances among the metals, marked the mineral production records for Canada during the first half of 1925. Production of metals and non-metals reached a total value of $90,347,698. as compared with $84,307,385. in the first half of 1924, an increase of 7.16 per cent. Metals and non-metals produced during the calendar year 1924 were valued at $17 4,202,537.; production during the first half of 1925 showed a sum equal to 51.86 per cent of this total. Advances among the metals were general. Gold rose to a new record. Lead advanced 62.41 per cent over the high mark attained in the first half of 1924. Nickel production was well maintained. Copper was up a million pounds. Silver showed increased values. Zinc followed the trend in lead to almost double the output recorded in the first half of 1924. Cobalt production continued to improve. Despite the loss due to the protracted strike in the Nova Scotia coal mines which reduced the output of coal in that province; during the six months ending June, to less than half the tonnage reported in the first six months of 1924, improved conditions throughout the rest of the non-metal mining field resulted in the production of non-metals during the half-year reaching a total value of $31,199,233. as compared with $36,844,286. in the first half of 1924; the loss in the value of coal output al one amounted to $5,723,873, while the decrease in the aggregate value of non-metals amounted to only $5,645,053.

Jan 1, 1925

By Qing-Xun Low

Ni current collector has excellent electronic conductivity and mechanica, properties. However, nicke, cannot be used in H2S-containing syngas SOFCs due to sulfur poisoning and coking. Copper coated nicke, is prepared by electrochemica, deposition. XRD, SEM, and EDX techniques are used to characterize the samples. After high temperature treatment in syngas containing, the coated samples exhibit high resistance of coke formation and sulfur corrosion compared to pure nickel. Therefore, copper coated nicke, is a promising anode current collector for H2S-containing syngas SOFCs.

Jan 1, 2010

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By A. F. Laurin, A. L. Dorr

"Because of its wide areal extent, its numerous lithological facies and its high degree of metamorphism, the Quebec portion of the Grenville province has only partly been explored and prospected. Rock types that are economically among the most interesting in the Grenville are those of mafic and ultramafic compositions, because of their great potential for coppernickel and chromium-platinum. The peculiar mode of occurrence and the distribution of these igneous masses in which copper-nickel mineralization is known to occur indicate' two common geological features: (1) aerial photographs and/or topographic maps strongly' suggest close spatial (and possibly temporal and genetic) association of most of these mineralized mafic and ultramafic intrusions with circular structures; (2) when plotted on a large-scale map comprising the Quebec portion of the Grenville, these circular structures fall along two lines which could correspond to major tectonic features. Even though the genetic links among the mineralized mafic-ultramafic masses, the circular structures and the linear features are not yet fully understood, their associations are believed to be empirically valid and should therefore be used as geological tools by those interested in exploring the Grenville for copper-nickel and possibly chromium-platinum deposits. It should be noted that these mafic and ultramafic bodies do not appear to be spatially related to anorthosite complexes."

Jan 1, 1971

By F. P. Hassani, J. F. Boily, A. M. O. Mohamed, M. Hossein

The optimal geochemical parameters required to form ellringite in a lime-remediated site have been investigated with the use of thermodynamic modelling. The speciation of sulphate and 10 metals analyzed in samples of a mine tailing from northern Quebec was calculated with a computer model. The model also includes calcium, which would result from the addition of lime to the system. Two speciation calculations were done. The first one is a hypothetical speciation before the onset of precipitation and was used to devise the stability fields of minerals susceptible of forming in high pHs. The stability fields were determined by building activity ratio diagrams with sulphate, aluminum and calcium species concentrations for pHs ranging from 4 to 14. The investigation was carried out for a 25°C solution with an ionic strength less than 0.12. Thermodynamics predict that an optimal stability field for ettringite in the mine tailing samples containing 10-3 mol/L SO4-2,10-2 mol/L of AI(OH)4 requires at least 10-2mol/L of Ca+2 and a pH larger than 11.6. The sulphate contents of the mine tailing samples, however, limit the precipitation of ettringite and monosulphate could be an end-precipitate. The second speciation is in equilibrium with precipitates and provides information on the speciation of the residual metals. If ellringite could be precipitated as a stable form, it could serve as a sorptive agent for residual metals, and, due to its binding properties, consolidate tailings.

Jan 1, 1995

By F. Calizaya, S. Bhattacharyya

"This study presents the results of a set of sound level measurements carried out in three underground mines where auxiliary fans are used regularly. Sound levels as high as 100 dB(A) by the workings and 115 dB(A) by the fans were measured in these mines. These levels are quite high even for intermittent noise. Ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard-rock mines are presented here. Factors such as fan type, rotational speed, and silencer-duct arrangements and their effects on noise attenuation are discussed. INTRODUCTION Auxiliary fans are used in hard-rock mines extensively. They are used to ventilate development headings, crusher rooms, conveyor transfer points, and underground shops. They are also used in developing long tunnels and ramps. Depending on the flow requirements and space restrictions, single or double stage axial fans with rigid or flexible ducts are used. Usually, they are high pressure (3.75 kPa) fans with flow rates ranging from 7.1 m3/s to 30 m3/s. The input power varies from 15 kW to 113 kW (Mutama, 2004; O’Connor, 2008). Typically, a 113 kW fan can produce sound levels as high a 113 dB(A) (Howes, 2005). Silencers are often omitted for cost reduction purposes or when used, they are not well maintained. Furthermore, silencers provide limited attenuation depending on their length and type. Typically, the sound attenuation ranges from 10 dB(A) for a 1 × D silencer to 14 dB(A) for a 2 × D silencer, where D is the fan diameter. In a mine, the silencer is subject to wear and tear, especially when the silencer is used in harsh environments. The interior lining can get clogged and the acoustic fill can get covered by dust and diesel soot, thus reducing the silencer performance. Periodic cleaning of the interior casing can increase the attenuation capacity of a silencer by 6 to 9 dB(A) (Dabson & Acuña, 2017). However, this requires a special silencer design in which the inner cartridge can be removed, the sound absorbing material replaced, the inner casing cleaned and the whole set retrofitted. A number of techniques can be used to reduce auxiliary fan noise in underground mines. These range from selecting the right fan for the job to installing adequate silencers. The choice depends on the air quantity requirement at the working place, cross-sectional area of the opening, duct diameter, fan type (axial or centrifugal) and local restrictions. Auxiliary ventilation layouts and best practices used to overcome potential problems related to overexposure to fan noise in underground hard rock mines are presented here. Factors such as fan type, rotational speed, duct diameter, and silencer-duct arrangements and their effects on noise attenuation are discussed."

Jan 1, 2019

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

By Michael Bauer

Increases in productivity and improvements in mining occupational safety and health are intrinsically linked. Over the past years, the German Hard Coal Mining Industry has been able to accomplish both: an increase in coal production and, at the same time, a significantly reduction of accidents. This success has been achieved by advances in technology, better organization and investment in people. Since 1990 productivity has more than doubled, while the total number of accidents has been reduced by more than 90%. Further development started initially with the mechanisation of the winning and drivage technology. Innovative technology and standardisation of the mining equipment were one reason for the increase in productivity and reduction of the accident rate. Therefore this technical development was not only one important pillar of the TOM model explicated later but also the requirement for the successful development of the other pillars. In addition to further developing this innovative technology it was possible to realise procedural and organisational improvements. As a result, the above achievement is based on implementing the three pillars of the so-called "TOM" model (technology, organization, ?Mensch? = human). To increase safety, improve performance, raise awareness and change of employees? attitude, the following technical and organizational requirements have been introduced: ??New innovative technology and procedures, standardized techniques and better equipment. ??Measures to revise or redefine the organizational structure, processes and systems of work, which were then integrated into the company policy and procedures as a company management tool. ??Personnel measures (investment in people). These include, improving motivation and behaviour, training, communication to raise and to change awareness of safety issues. Success in Occupational Health and Safety is not an automatic or self-regulating process. It needs hard work to make improvements and it must be treated as a recurring cyclic process. As a result of the above, occupational health and safety has become a natural part of daily work in the German Hard Coal Mining Industry. This could only be achieved by the unconditional "commitment" of all managers and employees to the issues, coupled with discipline and responsible action. Further improvements towards the ultimate aim of "zero" accidents are only possible by mutual involvement in implementing the ?TOM? (technology, organization and ?Mensch? human) model.

Aug 1, 2013

By Jason Mewis

Jason Mewis is the founder and president of ENGCOMP, a consulting engineering firm in Saskatoon Saskatchewan focusing on the mining sector. He has over 17 years of experience working on projects for the heavy industrial market in Saskatchewan, as both a Senior Structural Engineer and Project Manager. Jason is an entrepreneur with experience in many areas including estimating, planning, facilitation, and Risk Analysis. He has presented at many seminars and conferences across North America on the subject of Project Risk and and has become recognized for his expertise in this area of project management.

May 1, 2013

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By Andreas Gaich

COMBINED 3D IMAGES _ Highly detailed 3D geometry _ Identification of fine fractures together with a general impression of the situation _ Dealing with unfavourable outcrop geometries

May 1, 2009

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Stanislaw Trenczek

Natural hazards such as rock bumps, methane, coal dust explosions, airborne respirable dust, outbursts of gas and rocks, water, radiation caused by natural radioactive materials, spontaneous fires, and climatic hazards, occurring in the Polish hard coal mines, should be controlled. These hazards are characterized by different scale levels numbered from 2?5. To recognize the amount and levels of hazards, research works were carried out in 109 mining districts of mines belonging to Jastrzebska Spólka Weglowa, Katowicki Holding Weglowy and Kompania Weglowa. These are 86 % of all mines and could be regarded as representative of the majority of Polish mining. The hazards have been classified as regards the frequency of their occurrence as: commonly occurring ? with a frequency of 100 % (like airborne respirable dust and fire hazards), high occurrence frequency ? frequency from 60 to below 100 % (methane hazard ? 83.5 %, coal dust explosion hazard ? 92.0 %, and water hazard ? 99.1 %), medium occurrence frequency ? from 30 to below 60 % (rock-bump hazard ? 52.3 % and climatic hazards ? 51.4 %), and episodic occurrence frequency ? below 30 % (outburst of gas and rocks and radioactive hazards). The dynamics of effects of growth in hazard levels to their intolerable values is diverse. Some of them are passive in nature, which allows for longer observation of changes and appropriate early response (as for climatic and spontaneous fire hazards). However the majority of them take on the character of disasters, like methane or coal dust explosions and damage of the excavation structure ? as occurs after a rock-bump or rock outburst; and creation of an atmosphere unfit for breathing ? during open or spontaneous fires, or after gas outbursts containing methane. There are also latent hazards whose effects do not influence indeed a process of production; however they are detrimental to health when a worker is exposed for a long time to airborne respirable dust and radiation. For other types of hazards a level of danger may be only estimated. Since the systems monitoring allows a wider range of control, therefore, aside from rock-bump and methane hazards, there are monitored also fire hazards including measurements of other air parameters (velocity, pressure, humidity, temperature, O2, CO2 concentration). A few types of monitoring systems are used in Polish mines, like the monitoring systems for environmental parameters such as SMP-NT, SMP-NT/A, the telemetric systems CST-40, CST/A, including the computer-aided system for methanometry control officer SWµP, the computer-aided measuring systems KSP-1, KSP-2, KSP-2C, or the production and safety control system VENTURON. The underground part of the systems monitoring of natural hazards contains measuring devices and equipment for automatic control (power-off) of machines and electric devices in case of increased methane hazard. The surface part of the monitoring system allows the measuring data to be visualized and pre-alarm (warning) and alarm states to be displayed. Furthermore it makes it possible to archive and report the data and to control the underground supply and signalling devices. The EMAG Institute developed monitoring methods to extend a measuring range of monitored parameters (such as methane and fire hazards) as well as to monitor so far unmonitored hazards like dust hazards (by continuous monitoring of dust levels in mine air) and climatic hazards (by online monitoring climatic parameters of mine air).

Aug 1, 2013

By D. Marcotte

The Rock Quality Designation (RQD) is a standard scalar measure of rock quality used in common rock mass classification systems (e.g. RMR, Q system). RQD is measured along diamond drill holes. RQD interpolation between holes is nontrivial. Despite the inherent limitations of drill hole data and the local complexities of structural geology, it is often the only information available for mining and major civil engineering projects. Therefore, maximizing the usefulness of this data is warranted. We derive a correction for directional effects that help reduce the bias and improve the accuracy of the estimations. The correction is derived with the aid of numerous simulations. It relies on simple information, the angle between the joint normals and the borehole axis (JO). A reference direction is identified as the borehole direction with smallest JO. A multiple linear regression model based on JO statistics in the various boreholes defines the correction model. The corrected RQD values are then interpolated. It is shown the method enables reducing the bias on RQD estimation by 50% and improves the accuracy of the estimates by 30%. The corrected RQD values show stronger spatial continuity than the raw values. The benefits of estimating the RQD indirectly by using joint frequency measures are also assessed.

May 1, 2003

By Jan Butra

Longstanding mining of copper deposits in the Legnica-Glogow Mining Basin, Poland has accumulated broad experience concerning the impact of geological and mining conditions on seismic and rockburst hazard. Methods of rockburst prevention for deep copper mines have been developed based on gathered data. Methods of rockburst hazard evaluation and rockburst control constitute a set of rockburst prevention measures. Due to their nature and location within the production process, prevention methods can be passive or active. Active methods of rockburst prevention consist of the liquidation of stresses in the areas where they are concentrated through controlled generation of rock-mass tremors and rockburst by blasting works (group extraction blasting, release blasting in the rock mass and pillars able to accumulate the stress, as well as in the roof and floor). Group blasting works as a basic method are very effective in copper mine conditions. Provocation of dynamic events makes it possible to control the timing of their occurrence. In Polish copper mines, all blasting works are made during the absence of miners in the mining fields. Daily distribution of both the number of recorded strong seismic events and volume of energy released, confirm the advisability of using this kind of rockburst hazard prevention. The rockburst hazard prevention methods developed over 40 years of copper deposit extraction are economically reasonable and offer sufficient effectiveness under high rockburst hazard conditions.

Aug 1, 2013

By D. R. Wright

"The modest thermal efficiency of the steam turbine cycle essentially determines the heat required and, therefore, the coal consumption and ash production of pulverized-coal-fired powerplants. This paper emphasizes how some properties of coal and its ash can crucially affect the operation of a steam generator and its flue gas cleaning equipment. A brief reference to some siting factors and economics reaffirms the all-pervasive influence of the properties of coal and ash and establishes the importance of a firm supply of cooling water. The economics of scale remains a compelling factor in selecting the size of units, despite disappointing performances by some of the larger units. Environmental considerations suggest that smaller units still have a role to play. IntroductionCoal fuelled one industrial and economic revolution, beginning two hundred year s ago . It was the precursor of competing fuels, notably natural gas, oil and uranium, which eclipsed it in terms of convenience and rate of growth.The turmoil that now exists because of rapidly dwindling supplies of no-longer-cheap oil and the concerns about nuclear energy-justified or unjustified-exacerbated by an operating incident at the Three Mile Island Nuclear Powerplant, prompt speculation for a resurgence of coal, especially where it cangenerate electricity to replace energy from imported oil.The world's reserves of coal are not inexhaustible, although they are ample for several decades. Of greater import is the fact that the world's coal reserve s are more widely distributed than its oil reserves, and they appear less convenient as instruments of economic and political persuasion by opportunist powers. The crux is whether or not the world will accept all that a massive, if temporary, return to coal implies.Combustion of pulverized coal in steam generators to pro duce electricity is a 50-year-old, well-understood technique; it is undergoing continuous refinement to meet evolving environmental and economic criteria and is not found wanting. It is certainly the only technique available and technologically advanced enough to replace oil immediately on a large scale. Although it may take a decade to bring a new coal-fired powerplant into service, this delay is a reflection on nontechnical and administrative processes. Capital and operating costs of coal-fired powerplants are significant and subject to inflation, but, because of the accumulated experience in this field, the ability to control costs is better than for those energy processes which are less mature or still in embryo form. More exotic, soft energy systems, touted as the panacea for world energy problems, have still to prove themselves on the scale they are needed and under the stringent climatic and operating conditions coal-fired powerplants have already mastered."

Jan 1, 1980

By R. Cottam

The deformation and recrystallisation of magnesium yttrium alloys containing 0.23, 0.84 and 2.71wt% yttrium and commercially pure magnesium extrusion has been investigated at temperatures between 200 and 350°C. The alloys were produced as billets 7.5 cm diameter, solution treated at 525 °C for 8 h and extruded into 3 cm diameter bar at 390°C. Channel die compression was employed to deform the samples at a strain rate of 1x10-3s-1. For the 0.23 wt% yttrium alloy and the pure magnesium, dynamic recrystallization (DRX) occurred at all temperatures and the amount of DRX increased as the temperature was raised. In the alloys containing 0.84 and 2.71 wt% yttrium DRX was almost completely suppressed at all temperatures. The absence of DRX in the 0.84 and 2.71 wt% yttrium alloys was accompanied by a decrease in the ductility, except at 350°C the highest deformation temperature. It was observed that this increase in ductility was accompanied by a reduction in deformation twinning and the initiation of pyramidal slip. This work highlights the important role that DRX plays in enhancing the ductility of magnesium alloys.

Jan 1, 2006