Search Documents

By C. R. Edwards, D. R. G. Watt

"Equity Silver Mines Ltd. a member of the Placer Development group of companies operates Canada's largest silver mine near Houston in north-central British Columbia. Initially, the silver-gold-copper flotation concentrate contained excessive levels of antimony and arsenic, so a leach process was installed to remove undesirable metals and provide improved smelter terms for the leached concentrate. The leach plant which has been fully described elsewhere (1, 2, 3), was forced by deteriorating process economics to shut down in April 1984. Equipment was mothballed and alternate uses sought.The Endako Mines Division of Placer Development Limited, located some 150 kilometres east of the Equity mine site, shut down its molybdenite mining and milling facilities in the spring of 1982. Endako has continued to produce molybdic oxide (molybdenum trioxide or MTO) via intermittent roaster runs, and also a high purity, lubricant grade molybdenum disulfide in the Ultrapure Plant. With the steel industry in the doldrums, molybdenum chemicals present an alternate and growing potential for molybdenum sales. In 1982 Placer Development began testing this market. Molybdenum chemicals were produced in the United States on a toll basis using Endako MTO as process feed. The transfer of this production to Canada was being considered when Equity's leach plant shut down, and it was noted that most of the equipment and skills necessary could be provided by the leach plant. See Figure 1.A careful investigation of process requirements was completed by engineering and production staff at Equity and Endako. A provisional capital and operating cost estimate was made, and it was decided to perform a test run during July 1984. There were strong reasons to proceed with this project. A positive cash flow was expected for both Endako and Equity. Endako would have product to continue to expand in the molybdenum chemicals market with the added selling point that now the complete production process would be under direct control of Placer Development companies. Equity would further benefit since a portion of the leach plant would continue in operation thus maintaining and exercising our hydrometallurgical engineering and operating skills. Finally, Equity would have a base from which to search out other processes adaptable to the idled leach plant equipment."

Jan 1, 1986

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By Andre Vien, D. H. Hendriks, D. Willet, B. C. Flintoff

"For many years the training of mill operators was an informal process which involved senior operators training junior operators on an as-needed basis. Recognizing the needs and benefits of better training some companies, and even some provinces through legislation, have moved to ensure that a formalized training program exists in the plants. These programs tend to focus on basic safety and operations. Much remains to be done. With the more rapid incorporation of new processing and information technologies, and the goal to keep labour costs to a minimum by doing more with less, operator training has become a critical issue. This paper briefly examines the evolution of training programs, provides some measure of their effectiveness, and explores some recent developments which could have a very significant impact on the industry.PreambleOne can draw an analogy between operator training and the mechanical support of production equipment. When we buy a piece of process equipment it is critical that the mechanical installation be done properly to ensure that the device will operate at peak performance on start-up. Once the equipment is running, some form of preventive maintenance is required to ensure continued efficient operation. The operators and the equipment are both elements of the processing system, yet the former do not seem to get the same ""start-up"" or ""operating"" support. Are they not seen as critical to efficient operation? Why is this so? What impact does it have? How can we improve?These are all very logical and important questions, although the answers are not nearly so obvious. In the mineral processing industry, progress in operator training over the past thirty years has been limited and quite variable. To address the perceived need for a more coherent and consistent approach, some provinces have moved to incorporate basic training requirements in their legislation. Some plants have gone a few steps further by building integrated training programs into their operating culture. One conclusion which can be easily reached is that there are no standards, and that the range of training activity is great. In other words, a flotation operator is not a flotation operator is not a flotation operator. Their knowledge and skills are very much a function of training and experience, which are clearly corporate and site specific."

Jan 1, 1994

By R. S. Adhikari

It is necessary to assess the physical and functional conditions of highway bridges at regular intervals to ensure they still meet their service requirements. Currently, this condition assessment is mainly performed through visual inspection, which has been identified with several limitations (e.g. the timeconsuming assessment process and heavy reliance on inspectors? personal experience). In order to overcome these limitations and enhance the current inspection practice, this paper presents a novel method for automated bridge condition assessment using a hybrid sensing system. Under the method, existing conditions of bridge components are first captured with a stream of point clouds and color images. Then, the bridge components and the defects inflicted on the components are detected utilizing their visual patterns. The detection results are mapped to the point cloud. This way, the 3D information of the components and defects can be retrieved. The bridge condition assessment can be made effectively through the 3D visualization of this information before carrying out any on-site detailed evaluations.

Aug 1, 2013

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America's only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By Horace Freeman

Introduction This paper is an amplification of the paper presented by the writer at the last (1930) Annual Meeting of the Institute (1), and is somewhat in the nature of a progress report upon the introduction of pyrite into the field of Canadian consumption. The burner installed at the plant of the Canada Power & Paper Corporation, St. Maurice division, has been slightly changed in dimensions and has been put into continuous operation during the past year. As predicted, it has been possible to somewhat increase the steam consumption and at the same time decrease the amount of sulphur remaining in the calcine. The grade of the sulphur-dioxide gas produced has been maintained very steadily at 12 per cent, and sufficient experience has been obtained to determine the renewal cost of continuous operation. The object of this paper now is to encourage the development of pyrite, particularly by-product flotation pyrite, as it is shown that there is a very definite field in Canada for this material and that all the previous objections to the use of pyrite have been overcome, and that the use of the material in practice in paper mills has been developed to such a point that the operation of manufacturing the sulphite cooking-liquor is as simple as, or simpler than, the present style of operation with the use of sulphur.

Jan 1, 1931

By P. Henry

Hydrometal provides an adequate technology to reintroduce lost metal units into the industrial cycle, thereby saving resources and energy, while keeping the environment cleaner. Two case studies of our integrated hydrometallurgical recycling facility (Hydrométal) in Belgium are discussed.(I) Recycling of Cu-Co cement generated at the second purification step of zinc sulfate solution. (II) Recycling of lead complex materials from the lead industry.

Jan 1, 2008

By R. J. Grant, D. W. Scott, M. A. Cooper, E. R. Shannon

"The Brunswick No.12 site concentrator processes 10,500 tonnes per day of a complex lead, zinc, copper and silver ore producing four concentrates by differential flotation. Research over the years has led to increased understanding about the mineralogical and flotation characteristics of the ore. A pilot plant study conducted at Lakefield Research, primarily designed to investigate the technical feasibility of semi-autogenous grinding, provided an opportunity to test recent theories about grind size,, reagent schedule and flowsheet configuration.A fundamental approach was taken with each of the unit processes involved in grinding and flotation. Basic operating and metallurgical criteria were established in each area and a step-by-step implementation program initiated in the plant.Significant improvements in metallurgical and financial performance have been realized through the application of basic grinding and flotation principles using conventional milling equipment and without major capital expenditure. Current operating practice is detailed and metallurgical advancements cited.INTRODUCTIONBrunswick Mining and Smelting operates one of the world's largest lead and zinc mines near Bathurst, New Brunswick. Brunswick is a publicly traded company with majority ownership held by Noranda Minerals (63%). In addition to the No. 12 underground mine, the company operates a lead smelter and phosphate fertilizer plant in Belledune, N.B. and maintains a 25% interest in a joint venture with Noranda Minerals' Heath Steele mine near Newcastle, N.B. Through the four operations, a total of 2000 people are directly employed with fixed assets totalling Cdn$187 million (BM&S, 1991)."

Jan 1, 1993

By K. J. Brouwer, J. P. Haile

"Construction of the first stage of the tailings disposal facility for the Montana Tunnels Project was completed in October 1986. The project is located 37 km south of Helena, Montana, and involves mining of42 million tons of weathered diatreme are at a rate or 13 500 tpd to produce a gold/silver dore, as well as lead and zinc concentrates. The tailings disposal facility for the project includes a fully drained tailings impoundment for storage of the tailings solids, and a process waterpond for storage of all decanted water prior to recyling to the mill. The over-all facility is designed to achieve the basic objectives ofminimizing seepage to the environment in the short- and longterm, and achieving a fully drained stable tailings mass suitable for immediate reclamation on completion of mining. Specific features of the design include a soil bentonite seal and drainage system within the tailings basin, a free draining embankment with a design flow-through capacity of 4000 US gpm and an ultimate height of 230 ft (70 m), and a soil bentonite lined make-up water pond with a capacity of 420 acre-feet (530 000 m'). The tailings will be discharged in a rotational sequence through multiple spigot offtakes to achieve a thin-layer low energy laminar flow. This 'sub-aerial' deposition results in higher stored densities and maximizes liquid-solid separation on the tailings beaches. The over-all design played a major role in the successful permitting of the project, and was significantly cheaper than a conventional wet disposal system, with overall unit costs for tailings disposal of less than US$0.36 per ton.This paper outlines the site characteristics and the tailings material properties and their influence on the design. Extensive use was made of naturally occurring free draining materials as well as bentonite modified soil liners within the tailings basin, embankment and retention ponds. General construction procedures for the various components are described, as well as on-going construction requirements utilizing materials from the open pit. Finally, the over-all costs and unit costs for tailings disposal are presented."

Jan 1, 1988

By G. Vibert Douglas

IN a previous paper by Douglas and Gillies (1), a simple field test was given for gold. Later work by the present writers, and by others who have kindly written to us, shows that the test is not as satisfactory as it was hoped. In many cases, the gold mirror is completely obscured by a dense precipitate which, up to the present, it has been found impossible to remove. After many attempts, we have temporarily given up the iodine test and have been working on a simple pyridine reaction based on the work of Putnam, Roberts, and Selchow (2): The ore to be tested is ground to a fine flour. Place half a gram of this powdered ore (an amount that will cover a Canadian ten-cent piece, not heaped) in a six-inch test-tube and add 5 c.c. of aqua regia. The aqua regia. should be made up on each occasion, using four parts of hydrochloric acid and one part of nitric acid, both concentrated. Shake the solution in the test-tube for about one minute and allow to settle until dear. The rime to settle may be 30 to 60 minutes. When dear, a drop of the solution is with-drawn with a fine, dean eye-dropper or capillary tube and placed on à small glass plate. A slide such as is used for mounting rock sections is suitable. Now place an equal sized drop of pyridine solution on the plate beside that of the aqua regia solution to be tested. The pyridine solution, containing nine volumes of hydrogen bromide to one volume of pyridine, can be made up in advance and carried in a glass-stoppered bottle. Join the two drops with a glass thread or fine, dean stick, and allow the merged drops to stand undisturbed. I t is well to place the slide on a piece of white paper so that the presence of the crystals which may form can be easily seen. The time for their formation will vary with the amount of gold present, but the slide should be allowed to stand for at least 30 minutes before negative results are reported. A hand lens of at !east ten magnifications is essential. If gold is present, minute red crystals will form around the margin of the drops as these drops slowly evaporate.

Jan 1, 1938

By Charles S. Ney

"ZINC-LEAD REPLACEMENT deposits straddle the steep-sided valley of Kicking Horse River at a point three miles east of Field, B.c., in Yoho National Park. The Monarch orebodies extend into Mt. Stephen on the south side of the valley, and outcrop at two points, 1,000 and 1,200 feet above the valley floor. The Kicking Horse deposits are in Mt. Field, on the north side of the valley, and they outcrop 200 feet lower.The East Monarch outcrop is said to have been discovered in 1884 during construction of the Canadian Pacific Railway. The larger West Monarch outcrop, 700 feet west of the original discovery, was not reached till 1917 because of its nearly inaccessible location on the cliff face.The Kicking Horse mine was staked in 1906. Little development was done for several decades, and mining was not commenced till 1935.At the East Monarch, mining was commenced soon after location, and several thousand tons of ore were shipped prior to 1912. At this time a gravity concentrator was installed. This was operated till 1924, and a total of 42,000 tons of ore were mined, including about 10,000 tons from the West Monarch. The period from 1928 to 1935 featured flotation milling and the mining of 265,000 tons of ore, mostly from the West Monarch orebody. Intensive exploratory development was carried out in both Monarch and Kicking Horse from 1935 to 1946. Production from both mines in this period totalled 380,000 tons. From 1947 to the time of closure in 1952, considerable new ore was found in both mines and 185,000 tons were milled. Immediate possibilities for finding ore in the Monarch were considered exhausted. Kicking Horse orebodies are known to persist with a low grade of zinc. Total production from the two mines amounts to 842,500 tons grading approximately 7 per cent lead, 10 per cent zinc, and 1.2 ounces per ton silver."

Jan 1, 1949

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By J. E. Tupper

"This paper will discuss strategies for the introduction of computer technology in the mine environment. More specifically, it will focus on issues such as: (a) make or buy; (b) programmer less mines; and (c) support from corporate groups.The paper relates these strategies to systems for mine operations. These will be illustrated by considering the implementation of some phases of these systems at Teck Corporation.IntroductionThis presentation addresses some of the major considerations in a strategy for mine computerization and then relates these considerations to the computerization cycle and Teck Corporation.Strategy is defined as a conceptual framework or plan to accomplish a goal. For purposes of this paper, the goals can be more simply defined for operational purposes as either increasing revenue or decreasing costs.The strategy will allow us the framework for measuring tactical decisions such as computer and software acquisitions.The Mine Life CycleTo start with, let us look at the mine life cycle from a computer systems point of view:-Exploration-Property Development-Feasibility-Construction-OperationFrom a systems point of view, the exploration cycle is oriented to geophysical and geochemical computing. Property development starts with drilling and building the geological data base. The feasibility cycle includes all stages of evaluating the decision to proceed with mine development: ore reserve calculations; mine planning; and financial projections. Construction includes project management and project accounting systems. Systems required for operation are those needed by personnel at the mine site."

Jan 1, 1982

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019

By R. A. Frith

"Belts of Yellowknife Supergroup volcanic and sedimentary strata in the Slave Structural Province are separated by granitoid complexes. The strata and most intrusive rocks are 2.7 and 2.5 Ga old, but rocks around 3.1 Ga have been recognized in some of the complexes and are believed to represent a once-extensive sialic crust. Volcanics were erupted along rifts in this crust and the rifts became sites of crustal foundering and the development of troughs that filled with turbidites of volcanic and granitoid provenance. Present margins of the granitoid complexes may be close to the original margins of deposition of volcanics, with associated mineral deposits, and close to the thickest parts of basins of sedimentation.The Hackett River volcanic belt extends 100 kilometres between Mara River and Back River and is crudely S-shaped, with a northern sector surrounding a core of granitoid basement rocks, a northeasterly facin g central sector and a southerly facing southern sector. Up to 8 kilometres of andesitic volcanics with intercalated felsi c volcanic rocks are preserved within the central sector. The f elsic rocks include thick lenses of volcaniclastics with large, quartz-eye-bearing clasts, but the known metal deposits are not associated with these. Both of the deposit areas, the Hackett River area in the northern domal sector and the 'A itch ' Lake area 40 kilometres to the south in the central sector, are near the tops of relatively thin atypical volcanic sequences above suspected basement rocks. The Yava deposit near 'A itch , Lake overlies a unit of subaerially deposited, welded, andesit ic ash flows and the Hack ett River deposits overlie highly metamorphosed volcaniclastic rocks that include suspected ignimbrites.The deposits are notably argentijerous and lead-rich. They consist of stratigraphically zoned sheet-like bodies of iron sulphides, sphalerite, galena and chalcopyrite underlain by altered rocks containing chalcopyrite stringers. The Yava deposit was formed where hydrothermal fluids exuded through the fractured floor of a flooded caldera basin. The Hackett River deposits may have been formed in a similar setting and it is not inconceivable that all the known deposits in the belt were formed in a single large caldera basin, although there is no independent evidence for the required major fault separation between the Hackett River dome and the 'Aitch' Lake area."

Jan 1, 1980

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By Barbara A. Filas

The IFC goal is to promote private sector investment in developing countries which will reduce poverty and improve people?s lives. The developing country goal is to promote health, education and employment opportunities that improve their economies and their standard of living. The mining company goal is to Promote successful ?triple bottom line? mining projects that will grow shareholder equity

May 1, 2002

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By D. C. McKechnie

To the examining engineer, the ever-recurring problem involving the valuation of ore in a prospect presents at different times highly divergent aspects- some entirely physical or mathematical, others essentially personal. The majority of the problems discussed in this paper are obvious to the engineer, and need little elaboration. By the prospector and the general public, however, a number of these questions are often and completely over-looked, or else approached in such a way as to produce final results which are, to say the least, misleading and at times decidedly erroneous. While the purpose of this paper is to deal with prospects or potential mines, many of the problems considered apply equally well to mines with developed ore reserves. As the usual showings on a prospect consist chiefly of a few open-cuts and a limited amount of underground development work, an estimation of the actual ore reserves is a question of minor import, and seldom enters appreciably into an estimation of the probable value of the particular property. The physical valuation of a prospect mainly involves the consideration of such subjects as the general geological features exposed, the strength and type of mineralization, the width and persistence of any associated veins, shear zones, fractures or contact zones, together with the possible grade, size, and continuity of any ore-bodies that may there occur.

Jan 1, 1930

By Jose A. Caceres

Mine planning and mineral processing optimization are usually treated as two unconnected problems, especially at open pit and panel caving mines where the cut-off grade is practically the only variable optimized and analyzed for in the planning proposes. Using existing planning tool, the output is a reserve consumption strategy privileging higher grades. With the earlier consumption of the highest grades, every year produces revenues which are closer to the cost and potentially even below cost. However, there are other ore characteristics that can also affect the profitability of the operation. A new methodology has been developed, incorporating the grinding and flotation relationship into the mining economic models for the simultaneous analysis and optimization of the throughput-work index-recovery relationship through changes in the mining limits, sequence and redefinition of the reserve consumption strategy. A mine-site that implements this new planning strategy, can expect to increase the NPV from 5 to 15% depending on the actual operational settings. Two case studies have been developed, showing how the inclusion of the work index in the economic model changes the phase and mining sequence in an open pit mine and the caving sequence and the optimum column height in a panel caving mine.

May 1, 2004