Search Documents

By X. T. Zeng, X. Z. Ding, W. R. Chen, L. R. Zhao

The effect of deposition defects in metal nitride coatings on erosion behavior is presented. AlCrN, AlTiSiN, TiSiN and TiSiN:MoS2 coatings were fabricated by reactive cathodic arc evaporation and unbalanced magnetron sputtering processes. The microstructure and mechanical properties of the coatings were characterized by X-ray diffraction, scanning electron microscopy and nanoindentation, and the erosion property was assessed by solid particle impingement testing. The erosion characteristics on the coating surface and cross section were analyzed and correlated to the defects, which played an important role by promoting formation of erosion pits.

Jan 1, 2006

By B. M. Das, F. Claridge, V. K. Garga

Coal, as well as a large part of other minerals in Canada, is produced by surface mining methods. This has resulted in short and long-term accumulation of waste rock in dumps. Two main problems arise from the flow of water through these dumps: stability of dumps and the impact on stream flows. In recent years, a number of mines have started placing waste rock in valleys for general disposal or far constructing mine access road ways. All these have created challenges in the following areas: effective design of dumps and flow-through dams; stability monitoring of the structures; environmental impacts downstream by way of increased amount of fines in suspension, sedimentation, and toxic substances; and long-term status of flow and flood. Similar situations also exist in many civil engineering structures. This paper discusses the status of rock drains and the immediate and future research needs.

Jan 1, 1990

By Hung-wei Liu, Kevin Plucknett

Early attempts to manufacture titanium aluminides using blended elemental powders, through powder metallurgical processes, have been obstructed due to serious swelling during sintering. Although the use of pre-alloyed powder can avoid this undesired expansion problem, there are limited commercial powder sources available. Therefore, in the present research, fundamental studies on the synthesis of dual-phase (? plus a2) Ti48Al intermetallic materials is undertaken, in particular assessing powder manufacture. In order to produce pre-alloyed powders, highly porous Ti48Al pieces are initially sintered from elemental Ti and Al powder blends, and subsequently pulverised into powders. The powder size is then further reduced by use of either dry or wet milling processes (i.e. shatterbox grinding, attrition, or ball milling). Among these methods, shatterbox grinding has shown the highest efficiency, with a slight mechanical alloying effect observed. The manufactured powder morphologies and phases, as well the sintered material, will be discussed.

Jan 1, 2015

By A. Tikhonov, D. Kipper, V. Korovin, A. Olifirenko, Yu. Shestak

The present paper deals with vanadium and molybdenum sorption from industrial wastes and intermediate processing products using Cybber macroporous strong- and weak-base anionites. Vanadium and molybdenum recovery by Cybber anion-exchange resins as well as desorption processes were studied in static and dynamic modes; their efficiency was demonstrated for that purpose. The results of the work may be used to design technologies for complex processing of both ores and industrial wastes containing vanadium and molybdenum.

Jan 1, 2011

By Geir M. Haarberg

Electrochemical techniques, mainly linear sweep voltammetry and potential step chronoamperometry, were used to study the behaviour of dissolved phosphorus species in cryolite-alumina melts, The presence of AIPO4 or Na3PO4 gave rise to voltammetric current waves due to electrode reactions involving phosphorus species at potentials where dissolved alumina is stable in cryolite melts, Diffusion kinetics for dissolved P(V) species were studied, Data from industrial cells were used to determine mass balances for phosphorus, For cells being fed with secondary alumina, more phosphorus tends to end up in the produced metal, Laboratory experiments to study the effect of phosphorus in the bath on the current efficiency for aluminium were also carried out.

Jan 1, 2004

By A. P. Williams

"This paper presents an overview of plant electrical systems in general, a discussion of the problems that may occur due to plant growth, the maintenance required to maintain the reliability and safety of the electrical system, and the selectivity of the relay protection system. It is divided into two main areas: short circuit levels within the plant electrical system; and relay protection systems.This information is directed at maintenance supervisors, mine managers and electrical superintendents who have been away from detailed short circuit and relay coordination calculations for some time. It points out the potential problem areas within an operating plant electrical system. Short Circuit LevelsTheoryThe electrical equipment in a plant such as breakers, switches and starters has two short circuit ratings, the momentary rating and the interrupting rating. These ratings may be given in MVA or current (amperes) depending on the equipment and manufacturer's preference. Since for a three-phase system MVA and amperes are related by the formula"

Jan 1, 1987

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By A. R. Trusiak, C. Bazin, D. Hodouin

"The On-Stream Analyzer has proven, and is still proving to be, an extremely valuable tool for the control of flotation circuits. This paper examines the possibility of going further in the utilization of the analyzer results by using a real-time material balance program to calculate the mass flow rates within the streams of a circuit for process control, analysis and optimization as well as for the detection of sensor malfunction. The material balance algorithm improves measurements and give good estimates of unmeasured variables during normal operating conditions. The potential and limitations of the method are illustrated using results of an application to the Line 3 flotation circuit of Brunswick Mining and Smelting, New Brunswick.IntroductionThe On-Stream Analyzer (OSA) has gained, over the last two decades, the status of key instrument for the control of flotation plants. The OSA is currently used in almost every sulphide flotation plant and its application in oxide mineral flotation plants isincreasing. Commercial OSAs include a sampling system that collectssamples from various streams of a circuit and exposes thesamples to an X-ray beam. The sample then generates X-ray pulsesthat are converted into assays using multilinear regression programs(Leroux and Franklin, 1994). The estimated assays arepassed to the flotation operators via operator consoles, or to controlloops of various degrees of complexity (McKee, 1991), whichmanipulate reagent addition, aeration rate or froth thickness toensure an adequate operation of the plant. Although this applicationrapidly pays for the purchase of the OSA, one should ask:""Could we get more from the OSA?"""

Jan 1, 1995

By H. Warren Newcomen, Dennis C. Martin

"This paper describes the investigation of a large, progressive slope failure on the southeast wall of the east pit at Highmont Mine, British Columbia Geotechnical investigation s consisted of geological and structural mapping, assessment of blasthole drilling records, review of rock core information, slope movement monitoring and back analysis of various possible failure modes. Climate records and mining history were also assessed to determine their relationship to slope movement.Analysis of movement monitoring records and geotechnical information indicates that the failure is deep seated. The upper portion of the failure surf ace occurs along clay filled discontinuities. The lower portion of the failure surf ace appears to occur through the highly altered rock mass. High groundwater pressures and mining at the toe of the slope are documented to have had a major influence on stability at various times during the failure. Stability analyses results are presented and possible remedial measures are discussed.IntroductionHighmont Mine is located near Logan Lake in the Highland Valley approximately 50 km southwest of Karnloops, British Columbia (Fig. I). Mining of the porphyry copper and molydenum ore bodies began in 1980. In May, 1983, when mining in the east pit had progressed to a depth of about 60 m (200 feet) , a failure (designated the Southeast Failure) began to develop in the southeast corner of the east pit. Subsequent mining to a depth of 110m (360 feet) was accompanied by frequent and substantial slope movements involving between 500000 and I 000 000 m3 of rock . The slope was monitored extensively to assess short-term movement trends for operational safety. Geological mapping, core logging and rock mechanics testing were used in conjunction with the long-term monitoring information to determine the failure mechanism, conduct stability analyses, assess the effects of instability on pit design and enable design and installation of remedial measures."

Jan 1, 1988

By Dennis Z. F. Mraz

"Because rock salt and pot ash formations contain particles capable of elastic deformation, the material has usually been compared with various rheological models containing elastic elements. Extensive laboratory testing of salt and potash samples resulted in various theoretical conclusions based on conditions quite different from those in a deep mine. It is felt that sufficient data have now been collected from underground measurements and observations to demonstrate the inelastic behaviour of salt masses in a deep mine. The conditions in deep salt strata can be defined as near hydrostatic, because the acting pressures are very high compared to the negligible elastic limit of the salt. The pressure field and creep around the single opening is a function of its shape, size and age. The same factors, together with extraction, determine the behaviour of the mining a rea. The application of the correct analytical method in mine design can significantly improve the excavation techniques and predetermine the long-term behaviour of openings."

Jan 1, 1973

By Greg Gosson

These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own counsel in relation to any decision or course of action contemplated. Outline ??What is meant by a ?current technical report? under NI 43-101? ??When is a current technical report required? ??Who makes the decision regarding whether a technical report is current? ??Examples of the types of information that make a technical report no longer current for securities filing purposes.

May 1, 2009

By R. W. Zeindler, D. A. Fawcett

"A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxiliary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till.Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the crosspit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/ cross-pit conveyor system."

Jan 1, 1981

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980

By W. R. Richmond, T. S. Li, D. Ilievski

The reactive precipitation of ferrihydrite was studied in a laboratory semi-batch precipitator, where a highly concentrated sodium hydroxide solution was fed into an iron nitrate solution. Instantaneous hydrolysis of iron[III] takes place when the two reagents are mixed generating supersaturation, and leading to immediate precipitation of ferrihydrite via a primary nucleation mechanism then followed by limited crystallite growth to 3 to 7nm. A mathematical model of the semi-batch laboratory precipitator was used to simulate the pH responses during the precipitation of ferrihydrite at different reagent feed rates. The model comprised of interconnected compartments of averaged hydrodynamic conditions, incorporating physically meaningful turbulent mixing time constants. The precipitation process is described by the solute concentration conservation equation incorporating a postulated ferrihydrite primary nucleation model. It was found that the semi-batch precipitator model predicted the experimental pH response reasonably well. The experimental results demonstrated that the reagent feed rate has a critical effect on the course of the precipitation of ferrihydrite, i.e. it is a rate determining step given the fast hydrolysis and precipitation kinetics.

Jan 1, 2005

By P. A. Geusebroek, N. A. Duke

Abstract - The Lupin mine, located in the central Slave province just east of the western boundary of Nunavut Territory, is a world-class example of a Neoarchean-aged banded iron formation (BIF)-hosted lode-gold deposit. At the minesite the gold-mineralized Lupin BIF, separating stratigraphically underlying psammitic wacke and overlying argillaceous turbidite sequences, delineates the Lupin dome, a hammerhead-shaped F2/F3 interference fold structure occurring at the greenschist to amphibolite facies metamorphic transition within the thermal aureole of the Contwoyto batholith. Detailed paragenetic relationships indicate that peak thermal metamorphism coincided with the switch from regional D2 compression to rapid D3 unroofing of the Neoarchean orogenic infrastructure. Gold initially precipitated with pyrrhotite, replacing amphibolitic BIF at the apex of the Lupin deformation zone, separating the east and west lobes of the Contwoyto batholith. Over the course of associated prograde/retrograde metasomatic overprints, gold was further remobilized during garnet and loellingite/arsenopyrite growth in chlorite-altered selvages of late-forming ladder quartz veins. A metamorphic model of ore genesis, with gold being scavenged and transported by metamorphic fluid that was shed and structurally trapped at the amphibolite recrystallization front, is favored over the previously proposed syngenetic and exogenic models of gold concentration that have tended to polarize genetic interpretations to date.

Jan 1, 2004

By J. A. Finch

"This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified. IntroductionThis paper summarizes the findings of a detailed review of available technical information on the operation of rod mills. One of the basic problems in historical comminution testwork has been the lack of a standard measure of circuit performance. The Bond Operating Work Index, not introduced until after 1950, has proven of immeasurable value in this regard, but first has to be carefully considered in terms of its utility and limitations. Its prescribed use is described in a later section of this paper.During this review, it became apparent that rod mill performance is generally not well understood. Because of combined interactions, the effects of different operating variables may be difficult to assess, and even at times appear erratic. It is obviously difficult to rationalize plant testwork or circuit adjustments when the results are highly unpredictable. The purposes of this review, therefore, were:a) to establish what basic facts have been learned about rod mill performance;b) to define some genera l guidelines for efficient rod mill design and operation; and,c) to establish a basis for specific recommendations for plant tests or adjustments with minimum risk, and maximum potential for circuit performance improvement."

Jan 1, 1986

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By K. G. (Ken) Thomas

"This paper gives an insight into the various processes available to treat gold ores. A brief overview is given of the various types of refractory gold ores. Particular emphasis is given /0 comparing the costs of oxide vs refractory gold ore processes, inclusive of grinding through to dore bar.HistoryThro ugh time gold has been recovered from the earth's crust by various mean s. Five major historical steps can be identified for metallurgical processing as shown in Table I .Gravity concent ration started with, for example, river bed panning and developed to more sophisticated processes such as the Johnson concentrator, belt concentrator and jigs. The South African gold fields were a major developer of gravity concentration processes during the first half of the twentieth century.As coarse free gold became depleted, stamp milling, in conjunction with amalgamat ion , was developed. Basically, rock was crushed under large mechanical hammers an d the gold collected in mercury . The mercury was then evaporated in a retort to leave sponge gold for further fire refining.As deposits became deeper and gold finer, the gold became more difficult to recover ; fine grinding was required to liberate the gold. In the 18905, MacArthur and the Forrest Brothers of Glasgow, Scotland, introduced the cyanide pro cess for dissolution of gold and its subsequent precipitaiton by means of zinc. This process, in vogue until the early 1970s, was commonly referred to as the Merrill-Crowe process for recovering fine gold .Activated charcoal was used as a means of recovering gold from solution in the 1880s, especially in chlorination plants in Australia( l). Two factors probably retarded the development of carbon instead of zinc-based processes during those year s. First , there was no satisfactory procedure for the elution of carbon to allow its recycling and, second, the development of the Merrill-Crewe process for gold recovery by zinc cementation probably discouraged any further work on the use of carbon"

Jan 1, 1991

By James K. Gowans

"Cominco Ltd's Polaris Mine, located on Little Cornwallis Island, Northwest Territories (latitude 75degrees 30') went into production in late 1981, becoming the world's most northerly base metal mine. The concentrator, powerhouse, shops, offices, dry and warehouse, were uniquely designed and constructed on a 100f t wide by 400 ft long by 65 ft high barge. This process barge was constructed in southern Canada at Trois Rivières, then towed 3,500 miles into the High Arctic Islands and beached on Little Cornwallis Island.The paper deals with the original design philosophy, flowsheet and the initial year's operation of the Polaris process barge.IntroductionTo bring a mining property into production in the Canadian High Arctic, a company must deal with the harsh environment, the short shipping season and the high cost of labour. In trying to minimize the effect of these fact or s, the concept of a barge-mounted process plant was investigated as an alternative to the conventionally built concentrator. Cominco's previous experience gamed at the Black Angel Min e on Greenland's west coast suggested that this would be a practical alternative.The normal shipping season at Little Cornwallis Island is approximately six weeks long, from mid-August to the end of September. All equipment and materials must be delivered during the ""shipping window"". The logistics problems are enormous; if the conventional approach had been used the major process equipment would have been delivered to Little Cornwallis Island at the same time as the completed barge actually was! Construction would also be starting at the start of the worst climatic conditions, the Arctic winter. Nine months' production was gained by opting for the ""barge"" approach."

Jan 1, 1983

By A. W. Jacob

THE shatter cut, or burn cut as it is often called, is one in which the centre of the round is almost reamed out by drilling holes so close together that the blasting of a few holes shatters the rock embraced by all of them. The idea of shattering the centre of a face by shooting holes drilled parallel to one another is not new. Some miners have used this method for years past, when drilling quartz or a face near timber. But, they followed the age-old practice of first blasting the cut, then the square-up. It was not thought possible to shoot both together. In the case of machine men, the two largest contributors to silicosis are dust from drilling and dust from blasting. It follows, then, that material reduction of exposure to either constitutes an important step in lessening the incidence o silicosis. It was? the hope of being able to do away with the necessity of the men having to return early to a face, through dust concentrations of 60,000 to 80,000 particles per cubic centimeter, that aroused interest "in the shatter cut at McIntyre. Efforts to this end were successful. Now, with this kind of cut, all holes of a round are shot simultaneously.

Jan 1, 1942