Search Documents

The introduction consists of back-ground information, of an historical and statistical nature, relating to the Thompson mine. The geological presentation is based on illustrations that are intended to provide a progressively closer look at the ore occurrence. The illustrations consist of an index map, a geological map of a 15-by 85-mile area including the Thompson mine, a series of four maps dealing with the geophysics and geology of a 6-by 4\f.j-mile area at Thompson, a mine level plan and corresponding section, two sto11e 11lans and corresponding sections, and photo-graphs and photomicrogra11hs of the various one types. T HE Thompson mine is located about 400 miles due north of Winnipeg. The ore deposit was dis-covered in February, 1956. Five years later on March 25, 1961, the Thompson production facilities were officially dedicated with the shearing of the first nickel produced at the Thompson refinery. Full production, at an annual rate of more than 75,000,000 lbs. of refined nickel, was attained later in the year.

Jan 1, 1963

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

By D. H. Rousell

"Rocks of the Whitewater Group (Aphebian age) oc ithin the Sudbury Basin and consist of three formations rre, from oldest to youngest: Onaping, heterolithic breccias lus an igneous-textured component; Onwatin, argillite and siltstone; and Chelmsford, greywacke with minor argillite with siltstone. Mineralization in these rocks is as follows:1) Sulphides are disseminated throughout the Onaping Formation. Pyrrhotite, the major sulphide mineral, occurs mainly as fragments; other sulphides are chalcopyrite, sphalerite, galena, pyrite and marcasite.2) Zn, Pb, Cu, Ag and A u mineralization in the Vermilion member, a carbonate-chert unit near the base of the Onwatin Formation (Vermilion and Errington mines).3) Pyrite and minor base metals in the Onwatin Formation .4) Mineralized quartz veins, located at or near the base of the Onaping Formation, include such deposits as Moore Lake (Pb, Zn and Ag), Foisey (Zn, Pb), Papineau (Cu, Au and Co) and Proulx (Pb, Zn, and Cu). Quartz-carbonate veins in a meta-gabbro sill contain Cu, Zn, As and Au. Material from quartz veins from two former ""gold mines"" (Gordon Lake and Creighton) yielded no Au values.5) Anthraxolite veins in the Onwatin Formation .The mineral occurrences can be explained in term of either the volcanic theory or meteorite-impact theory of basin formation. According to the latter theory, the sulphide fragments in the Onaping Formation may have been formed by the brecciation of sulphide-rich pods located in the upper mantle and at the base of the transient crater; some of the sulphides may have been derived from target rocks of the Huronian Supergroup. The Vermillion-Errington deposits may represent sedimentary exhalative deposits of the Remac type; mineral-rich brines, trapped at the base of the transient crater, rose upward and precipitated the mineralized carbonate-chert under reducing conditions. These conditions continued throughout the deposition of the upper Onwatin Formation but pyrite was the only sulphide that formed.The quartz veins were emplaced during the time of basin deformation. Metamorphism remobilized and concentrated carbonaceous material in the Onwatin Formation 10 form the anthraxolite veins."

Jan 1, 1984

By Yan Jie

A series of production technologies are described for gold recovery from complex gold concentrate blended with copper concentrate treated in the SKS smelting process comprising: 1) Feed preparation and proportionate feeding of complex gold concentrate and copper concentrate; 2) SKS smelting gold recovery operation and process control technology developed based on reaction mechanism, process simulation and slag formation optimization study; 3) a dry-process quenching arsenic collection technology developed during de-bottlenecking severe restriction of SO3 in the off-gas on As collection system by suppressing and eliminating SO3 in off-gas as a result of optimizing SKS smelting process conditions and spraying caustic soda absorbent so as to reduce off-gas dew point temperature; 4) electrorefining of impure anodes; 5) technology for recovering such precious metals as Au, Ag, Pt, Pd, etc. from high-Sb copper anode slime produced as a result of gold recovery from complex gold concentrate by using SKS smelting process. INTRODUCTION Gold concentrate resources in China are mainly found in Shandong province, Henan province and the Inner Mongolia Autonomous Region, etc. Currently, recovery of gold is based on pre-oxidation (roasting) cyanide leaching process. This process produces a large amount of cyanide-containing wastewater, cyanide leaching residue and relatively high SO2-bearing flue gas during production, which can cause increasingly more serious environmental pollution issues. Besides, this process route suffers from a relatively low precious metals recovery (70–80%) found when treating refractory gold concentrate and carbon-bearing gold concentrate. These issues have severely restricted the development of the precious metals processing industry in China.

Jan 1, 2019

By W. Díaz, R. A. Parra, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

This work presents visible-near infrared (VIS-NIR) spectroscopy measurements, and signal analytical techniques to characterize minerals and relevant pyrometallurgical process variables for the copper extractive industry. Data signal processing techniques such as baseline correction and numerical analysis are used to estimate the continuous and discontinuous spectral components. Such spectral components are used to estimate the process temperature, and patterns such as the integrated radiation. Also, metal combustion emissivity calculation are depicted. Our findings suggest that VIS-NIR spectroscopy may be a suitable technique to assess the process condition state, appearing as an interesting sensing alternative. INTRODUCTION Although the flash smelting process is one key stage in the copper extractive industry, representing about 40% of copper matte production worldwide (Cantallopts, 2017), few attention is dedicated to develop sensing solutions to assess process variables, such as mineralogical composition and temperature, in the feeding and bleeding stages, compared to the steel industry (Strakowski, et al., 2014). In this process and other industries, e.g. the thermoelectric power generation one, combustion and particularly the generated flame are the production chain’s heart. Since the flame is a highly radiative emitting process where chemical and physical transformations take place, many works had been dedicated to characterize the combustion state by sensing its radiation using optical and photonic technologies (Ballester & García-Armingol, 2010). In this context, this work aims to contribute with visible-near infrared (VIS-NIR) spectroscopy and pyrometry techniques to retrieve relevant information from a laboratory scale flash smelting process. On the other hand, since photonic instrumentation allow us to perform contactless measurements of emitted, absorbed, transmitted or scattered radiation, it appears as a suitable technique for sensing process properties in harsh environments, e.g. high temperature processes. One of these techniques is the Visible- Near Infrared (VIS-NIR) spectroscopy, which provides information about the spectral radiation intensity distribution, in this work, the emitted flame’s radiation. It is well known in combustion research that the spectral emission from a flame is composed by a black body continuous radiation background, molecular emissions, elemental emissions and additive noise features (Arias et al., 2011). To make sense of such information signal processing techniques are needed, here we propose to analyse the continuous and discontinuous spectral components separately.

Jan 1, 2019

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By M. Pierce

Empirical relations exist for the estimation of rock block strength at scales larger than standard core sizes. Two recently published relations account for the significant impact that microflaws (pores, open cracks, veins) and weathering/alteration can have on scale effect. These relations were used to estimate the rock block strength of heavily microfractured quartzite from the Bingham Canyon Mine. Predictions were compared to the results of Uniaxial Compressive Strength (UCS) tests conducted on cylindrical core samples of varying microfracture intensity and diameter. The comparison confirms the sensitivity to microfracturing suggested by existing relations and suggests that they would benefit from more detailed consideration of microfracture strength, density and persistence over a range of scales. The results of a numerical study illustrate how Synthetic Rock Mass (SRM) modeling techniques could be used to complement empirical data in the development of such relations.

May 1, 2009

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By M. Sommerfeld, U. Schwarz-Schampera, B. Friedrich, D. Friedmann

The steadily growing demand for metals and their price increase at metal exchanges make the mining and utilization of marine mineral resources like polymetallic nodules, manganese crusts or sulfide deposits in the near future a viable option to potentially increase the supply of base and precious metals. For a country with low potential to mine land-based resources like Germany, the industrial recovery of metals from marine mineral resources could lead to a decreased dependency on imports. In this study, seafloor massive sulfides from the German license area in the Indian Ocean (Kairei field, Southern Central Indian Ridge) are treated to recover copper and precious metals. The aim of the project is to demonstrate the transferability of existing metallurgical techniques to the raw material of deep-sea massive sulfides. As a starting point to process this unconventional resource, samples from the Indian Ocean are chemically analyzed and mineralogical characterized. A comparison is carried out between the samples and land-based copper resources, to highlight the potential which lies in mining the deep-sea floor. This paper will show the general possibility of applying a two-stage pyrometallurgical process, based on a concentrate smelting operation, followed by a converting operation in lab-scale to the provided samples of massive sulfides. Generated slag from the concentrate smelting and the converting operation are investigated by X-ray diffraction to determine the mineralogical composition. The two-stage pyrometallurgical process is investigated by the thermochemical modelling tool FactSageTM 7.2 to evaluate the phase distribution of relevant elements between the metal, matte, slag and gas phase. The thermochemical boundaries of the pyrometallurgical process are therefore set and the results of the thermochemical study can be used as an indicator for the efficiency of an up-scaled process and the generated amount of side-streams, which need to be further treated or circulated back into the process. INTRODUCTION Seafloor massive sulfides (SMS) are the third kind of discovered deep-sea minerals besides ferromanganese nodules and cobalt-rich ferromanganese crusts (Sharma, 2017). They occur in water depths around 250–4,000 m (Koschinsky et al., 2018). SMS are characterized by a high base metal and sulfide content. They were created by fluid circulation and hydrothermal convection over time (Han et al., 2018). Commonly, areas rich in SMS are associated with hydrothermal vent fields on the seafloor (Keith et al., 2018).

Jan 1, 2019

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By E. Best

In 2003, Phelps Dodge Mining Company decided to pursue the design and construction of a Central Analytical Laboratory to provide chemical analyses for their Arizona and New Mexico operations. This centralized approach was selected in place of refurbishing six (6) older laboratories that operated at the various Phelps Dodge sites, and which would not have permitted full automation and use of robotics. The new lab was designed by the Process Technology Center (PTC) Material Characterization Group in cooperation with IMP Group. The Central Analytical Service Center (CASC) encompasses fully automated sample preparation of blast holes and geological samples weighing up to 15 kg/sample. The CASC also includes the first "wet chemistry module" worldwide to be operated by robotics systems to perform Total Cu, Acid Soluble Cu, and Quick Leach Tests (QLT), and a fully automated lab for electrowon copper cathode. The new lab also offers flexibility for handling specialty samples and analyses by either semi-automated or manual mode. Data handling and transfer is accomplished using the commercially available StarLIMS system. Commissioning was accomplished within five (5) months of startup during which the CASC also handled 86% of a full production load. The 24/7 lab operation has already exceeded its design capacity, has achieved considerable savings in operating cost, reduced sample preparation errors, and significantly increased analytical quality.

Jan 1, 2007

By J. A. Irvine

In 1972, a cooperative program to map and estimate the quantity of Tertiary coal resources in southern Saskatchewan was initiated by the federal and Saskatchewan governments. More than 700 exploratory boreholes were drilled over a two-year period, and data were obtained from other organization s on an additional 1500 boreholes in the area. Stratigraphic data and data on each coal seam penetrated in the boreholes, along with technical and location data for each borehole, were stored in a computer data base for convenience of retrieval, modification and manipulation. Programs and program packages were developed or adapted to: (1) select borehole information defined by variable retrieval parameters from the data base; (2) calculate derived information , such as overburden ratios. cumulative net coal thicknesses , mean weighted center of gravity of coal seams in each borehole, etc., from the selected data ; (3) produce posting maps of either selected data or calculated information in various combinations at variable scales on a plotter or CRT display; (4) produce contoured structure, isopach or ratio maps , and perspective diagrams as appropriate , utilizing plotter or CRT display; (5) calculate and categorize quantities of coal in place within user- defined "mineability-economic-reliability" limits. The emphasis in computer utilization was placed on geological credibility of the results and ease of operation by relatively untrained geological personnel, resulting in extensive use of interactive methods. The single most important benefit derived from using computer-assisted procedures is the ability to produce new maps and quantity estimates rapidly and inexpensively as a result of availability of new data or/and changes in external criteria which impose economic or mineability constraints.

Jan 1, 1978

By L. R. Bottomer, G. M. Leary

"The Copper Canyon property is located in the Galore Creek area of northwestern British Columbia. Porphyry copper-gold mineralization on the property is notable for its high gold content and close spatial relationship with a distinctive suite of high level syenitic and monzonitic intrusions, and pseudoleucite-bearing volcanic country rocks. The style of alteration and mineralization is similar in many respects to the nearby Galore Creek deposits.The current geological resource of 32.4 million tonnes grading 0.75% Cu, 1.17 g/ t Au and 17.1 g/t Ag is insufficient to support a mining operation, but definition of additional reserves combined with improved transportation infrastructure in the region may change this in the future. The climate, topography and proximity to an active glacier indicate that the most likely production scenario is an underground bulk mining operation, with the ore being milled offsite.IntroductionThe property is located at 57°07' North latitude, 131 °21' West longitude, on NTS sheet 104G/ 3W, approximately 160 km northwest of Stewart and 90 km south of Telegraph Creek (Fig. 1). The Galore Creek camp and airstrip are located 6 km to the west. Current access to the property is via helicopter either from Galore Creek, or from the Bronson Creek airstrip 32 km to the south-southeast.The deposit occurs within the Boundary Ranges of the Coast Mountains, on the north side of the east fork of Galore Creek, which flows northerly into the Scud River and thence westerly to the Stikine River.Topography is rugged. In the deposit area, elevations range from 1130 m to 1750 m. Valley glaciers and permanent snow and ice fields are characteristic of the region at these elevations, and at its southern limit, mineralization is truncated by the East Fork Glacier.The property is entirely above the treeline, and except for areas of moraine cover and talus slopes, outcrop is abundant."

Jan 1, 1995

By J. E. Hawley

"The zinc-lead deposit of the Lake Geneva Mining Company is on lot 7, con. VI, Hess township, Sudbury district, Ontario, about 10 miles northwest of the northern rim of the Sudbury Basin. Though a relatively small deposit, it shows some rather interesting relations to cross-cutting, pre-ore, quartz diabase dykes, which merit description.The deposit was discovered in October 1924 by J. H. Collins beneath iron-stained drift and oxidized sulphides. This proved to be the northwestern extremity of the orebody, the remainder of which extends southeast below swampy ground. Exploration began in 1927. In 1928 a vertical shaft was sunk to 250 feet and a level established at 235 feet. Later the shaft was deepened to 400 feet and new levels opened at 315 and 375 feet. In 1943 an inclined winze was sunk below the vein from the 315-foot level to a vertical depth of 640 feet, and two additional levels were opened at 525 and 615 feet respectively.The geology of the area has been described by T. T. Quirke (1), F. F. Osborne (2), F. J. Alcock (3), and Ralph Tuck (4). Private reports have also been made by Carl Tolman, J. E. Gill, and K. W. Fritzsche. Tuck's paper, covering the work completed to 1930, gives a detailed account of the character of the ore and enclosing rocks.Up to May 1944, when the property was closed, all ore above the 375-foot level and a small tonnage from below this elevation had been removed. Ore mined from 1941 to 1944 yielded the following:"

Jan 1, 1954

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

By P. M. Dranchuk

"""PLANET EARTH seen from space appears as a fragile and limited life-supporting system in a vast emptiness. That such a view is, in fact, an accurate one is now more widely accepted than it was not long ago, before Earth's problems of over-population, overconsumption, limited resources and environmental degradation attained the limelight. The danger is that a government and public now deluged by doomsday prophecies and bemused by equally confident reiterations that technology will cure all may hesitate in coming to grips with the problem, in the hope that, given time, it will go away."" With these words, Preston Cloud begins a recent editorial, in Science(l), in which he presents a brief resume of some of the findings of the Committee on Resources and Man of the National Academy of Science-National Research Council(20.Their report, which is based on a two-year study by an extremely competent group and consists of some 250 pages of text, is even more far-reaching and sobering than the report on Energy Resources(3). It begins by quoting Sir Macfarlane Burnet as follows:""There are three imperatives: to reduce war to a minimum; to stabilize human population, and to pre-vent the progressive destruction of the earth's irreplaceable resources.(4)"

Jan 1, 1971