Search Documents

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By N. Dufresne

"The evolution of mining methods at Brunswick Mining and Smelting shows that, in the case of a large deposit, technology must adapt itself to changing conditions. As problems are encountered, management must modify their approach if they hope to meet production quotas. This search for new and better ways started with the opening of the No. 12 orebody and is still going on today.From large-scale open stoping, the Brunswick Mining and Smelting operation went to transversal cut-and-fill, then to longitudinal cut-and-fill, which is the main mining method now employed. However, to solve certain problems experimenting with Avoca methods was initiated. Rebar grouting and prepinning have also made significant contributions toward securing relatively poor ground in the hanging wall and holding badly fractured backs in wide stoping areas. Introduction In 1952, M.J. Boylen had incorporated Brunswick Mining and Smelting Corporation Limited to develop his recently found No.6 and No. 12 orebodies near Bathurst, New Brunswick. Between 1953 and 1957, St. Joseph Lead Company was brought in to try and initiate mining . During those years, St. Joseph Lead sunk two shafts at No. 12-No. 1 to 425 feet below surface and No.2 to 982 feet. They also developed the 200 and 350 levels to sample the ore at depth and operated a 100-tpd pilot plant at the No.6 mine. However, due to low recoveries and depressed metal prices. the project was shut down in 1957.A group including M.J. Boylen. K.C. Irving. Maritime Mining Corporation and Patino Corporation reacquired the property from St. Joseph Lead Company in 1961. New financing was arranged involving La Societe Generale des Minerais, S.A . of Belgium and Engineering Consultants Limited of Saint John. New Brunswick. During the years 1962 and 1963, construction of surface and underground facilities progressed rapidly."

Jan 1, 1981

By A. O. Dufresne

WITHOUT transportation, mining would be quite impossible. Any person familiar with the operation of a mine knows full well that from the minute ore is blasted, it is kept moving until it reaches the treatment plant. In the mill, by means of conveyors and elevators, the ore is brought from receiving bins to one machine after another until finally its valuable mineral is separated from the gangue. The finished product must then be shipped -either by boat, rail, or motor trucks to industrial centres, where it undergoes further treatment and transformation into finished commercial goods. Everybody appreciates that the winning of an or-e includes, amongst various operations, the moving of large quantities of material of generally low value. Transportation, therefore, must be considered One of the most important factors in the economics of mining. My assignment, this afternoon, is not to treat of that phase of transportation as it directly affects mining operations, but rather to consider some of the aspects of overland transportation and its influence in bringing about the development of mining camps in Canada. I shall take the liberty of rapidly surveying conditions facing prospectors, mine developers and operators from the time a region is still in a pre-pioneering stage until such time as a mine starts shipping its concentrates.

Jan 1, 1956

By M. F. Goudge

MAGNESIA refractories and magnesium metal are both essential war commodities. The need for magnesium, which had just made its debut as a commercial metal a few years before the outbreak of the present war, is widely known because this new and valuable light metal has already received much publicity. Less widely known but equally important in the war effort are magnesia refractories. They are indispensable to the efficient functioning of the great metallurgical plants producing steel, nickel, copper, and other metals, where, because of their resistance to extreme high temperature and chemical attack, they are used in lining the furnaces, which are operated at a white heat. The demand for refractories in the metallurgical industries rose rapidly upon the outbreak of war, and now, in consequence of the continued great expansion under way in the manufacture of steel, nickel, copper, and other metals, the need for magnesia is greater than ever. Since 1915, part of the Canadian requirements of basic refractories has been supplied from the deposits of magnesitic dolomite in Argenteuil county, Quebec. The products from these deposits are excellent for many uses, but the magnesitic dolomite has too high a content of silica and lime to be used in making a type of magnesia brick required in nickel converters, and in the roofs of reverberatory furnaces used in the copper and steel industries. There is now a large and growing demand in Canada for bricks and shapes for these uses. This demand has always been supplied from the United States. Makers of these products in the United States, in turn, formerly imported most of the necessary high-grade, dead-burned magnesia from Austria and Manchuria. Not only are these sources closed, but refractory chrome ore from the Philippines is no longer available and chrome refractories may have to be in large part replaced by magnesia.

Jan 1, 1942

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By J. R. Andrews, R. P. Young, J. M. Reyes-Montes

"Microseismic monitoring provides insight into the location and extent of rock-mass fracturing induced by cave mining, enabling interpretation of the cave profile and validation of predictive numerical models. Source location uncertainties can lead to misinterpretation of the inferred characteristics of the fracture network. One principal source of uncertainty is the velocity model used to invert the location algorithm. Large-scale 3D numerical models of modulus changes across a caved mass can represent such complexities in the location algorithms, allowing more accurate interpretation of the microseismic activity. A Northparkes mine case study applies this advanced approach to microseismic data interpretation.RÉSUMÉ Le suivi microsismique fournit des renseignements sur la localisation et l’étendue des fractures de la masse rocheuse induites par l’exploitation par blocs foudroyés; cela permet d’interpréter le profil de la chambre foudroyée et de valider les modèles prédictifs numériques. Les incertitudes quant à la localisation de la source peuvent conduire à des mésinterprétations des caractéristiques inférés du réseau de fractures. Une des principales sources d’incertitudes est le modèle de vitesse utilisé pour inverser l’algorithme de localisation. Des modèles numériques tridimensionnels à grande échelle des changements du module d’élasticité à travers une masse foudroyée peuvent représenter de telles complexités dans les algorithmes de localisation, permettant ainsi une interprétation plus juste de l’activité microsismique. Une étude de cas à la mine Northparkes applique cette approche avancée à l’interprétation des données de microsismicité."

Jan 1, 2016

By G. Eaton

Safety management is an important mortal and business function in construction. Contractors have traditionally tracked and reported lagging indicators, e.g. fatalities and lost-time accident rates, to measure their safety performance and stay in compliance with relevant regulations. Over the last several decades, contractors became more proactive in their approach to safety and developed programs that track leading indicators, e.g. safety audits and safety climate. In particular, safety climate measures workers? perception of safety management and its effectiveness in the workplace. Past literatures indicated that, while some industrial construction contractors ignore safety climate measures, others are limited by a lack of a formal means to measure safety climate. In this study, a survey approach is used to measure an industrial construction contractor?s safety climate through three key areas: management commitment, job control, and general safety climate. As a pilot study, a total of 214 individuals at a fabrication facility participated in the survey to verify the validity and effectiveness of the proposed survey approach. This survey study also confirms that job control and management commitment have a positive correlation and that worker demographics have an effect on respondents? perceptions of management commitment.

Aug 1, 2013

By C. H. Ash

"The Red Chris Cu-Au deposit (522.7 Mt at 0.35% Cu and 0.27 g/t Au), northwestern British Columbia, is one of several pre-accretionary porphyry systems in the Cordillera of westernCanada. It is hosted by an Early Jurassic hornblende monzonite to quartz monzodiorite porphyry which forms part of a suite of dikes and stocks that intrude Late Triassic volcanic strata. Major and trace element chemical data suggest that these Early Jurassic intrusions have compositions which fall on the boundary between alkalic and calc-alkalic compositions. Alteration and mineralization in the Red Chris deposit are more typical of calc-alkaline porphyry systems with abundant potassic, sericitic and argillic assemblages and quartz-rich stockworks. It lacks Na- and Ca-bearing silicate assemblages which characterize the alkalic porphyry deposits of British Columbia. One of the more unusual features of the deposit is the abundance of carbonate alteration and veins which occur throughout the hydrothermal history of the deposit. This type of alteration and veining is more typical of alkalic porphyry deposits.The composition of the carbonates vary both temporally and spatially with different alteration zones. Potassic zones, which are characterized by orthoclase±albite±quartz±chalcopyrite±bor-nite±magnetite±hematite and Au/Cu ratios of 1:1 (g/t Au:% Cu), contain minor siderite veins and alteration. Quartz-sericite-carbonate (QSC) zones overprint earlier potassic alteration and comprisequartz+ankerite+sericite+pyrite+chalcopyrite with Au/Cu ratios of 0.5:1 (g/t Au:% Cu). Ankerite isthe main carbonate in this stage but has a variable composition with a more Fe-rich variety associated with mineralized veins. Localized chlorite-carbonate alteration zones, characterized by chlorite+carbonate+quartz±kaolinite±pyrite±gypsum and high Au/Cu ratios [2 to 3.5:1; (g/t Au:% Cu)],contain predominantly calcite. Late stage carbonate-gypsum veins have an ankerite to dolomite com-position which is very similar to the regional carbonate alteration and veins."

Jan 1, 1997

By Jochen Petersen, Jean-Paul Franzidis, Allan Nesbitt

This study presents a method for the determination of intra-particle diffusivities in ion-exchange resins for the purposes of evaluating the state of resin degradation during service. The method uses a zero length column (ZLC) in a closed circuit with variable speed pump and reservoir. The intra-particle diffusion is determined from absorption data by using the Nernst-Plank approximation along with the ‘mass transfer factor’ - which is a product of the mass transfer coefficient (kf )and the concentration of the adsorbing ion in the liquid at the surface of the resin - in a computer algorithm fitting simulated curves to experimental data.. Through this approach the changed intra-particle diffusivity, of a gel-type acid resin, over a 1000 loading and elution cycles, is shown.

Jan 1, 2014

By Dwayne D. Tannant

The Adra tunnel near Naramata BC experienced a fire in 2010 that burned timber sets within the tunnel and caused severe spalling of rock from the roof and tunnel walls. The nature of the damage is documented and efforts completed to rehabilitate and open a portion of this tunnel to the public are described. The use of shortcrete and rock bolts is a technically and economically superior support system to timber sets as well as being far more fire resistant.

Jun 1, 2012

By Neil Campbell

"The gently-dipping Devonian dolomite beds south of Great Slave lake in northern Canada are nearly every-where concealed by a cover of glacial drift and muskeg. Nevertheless, in 1898 or earlier, four small outcropping areas of dolomite, richly mineralized with lead and zinc sulphides, were discovered. Exploration work performed here up to the end of 1930, included intensive trenching and drilling of the showings, together with mapping and wide-spaced drilling in the surrounding region. This work proved that the discoveries are isolated pockets of mineralization much too small to be commercially valuable by themselves. No evidence of orebodies elsewhere was reported.Meanwhile, mapping by the G.S.C. in the Shield far to the east disclosed major Precambrian faults, some of which can be projected southwesterly (under a cover of Paleozoic sediments) to the vicinity of Pine Point. During the period from 1940 to 1947, consideration was given, by The Consolidated Mining and Smelting Company Ltd., to evidence of a theoretical possibility that, although apparently dormant in Paleozoic times, these faults may have provided a structural control and a source of ore-bearing solutions in some post-Devonian period. From this, it was postulated that the breaks might have created, in the overlying dolomite, a linear array of orebodies concealed by overburden but lying in a belt of considerable length and in a position predictable within practical limits. A program of drilling designed to test and exploit this specific concept was conducted from 1948 to 1955.he drilling within the new, theoretically-defined search area resulted in the discovery of many lead-zinc ore-bodies, none of which was exposed at the surface. Some of these are large and (as indicated by 1965 production records) very rich. They are situated 1 to several miles distant from, and apparently not connected to, the earlier-known surface discoveries. The drilling also disclosed that the ore, which consists of disseminated sphalerite and galena replacements together with colloform sphalerite and coarse galena cavity fillings, occurs mainly at certain stratigraphic horizons within a large, coarsely-recrystallized dolomite barrier reef. Considerable fracturing and folding was found. It has been suggested that reef development was influenced by post-Precambrian tectonic movements associated with the old faults in the basement complex. The ore may have been deposited by solutions moving from distant sources to favourable structural and chemical environments in or related to the reef.In more recent exploration performed in the course of preparing for mining production, the rate of ore discovery within the same general geological context has been greatly accelerated by the use of new geophysical techniques and drilling equipment. Reserves of 21.5 million tons, averaging 4 per cent lead and 7.2 per cent zinc, were reported in 1965, and production from open pits at the rate of approximately 248,000 tons of concentrates per year is in progress"

Jan 1, 1966

By A. McLean, W. Q. Chen, W. Yan, M. Barati, Y. D. Yang

In order to maximally remove the harmful impurities phosphorus and reduce the loss of valuable elements from Si-based alloy for production of solar-grade silicon, thermodynamic properties of the Si-based alloy were studied. In this work a new model, the Molecular Interaction Volume Model (MIVM) derived from statistical thermodynamics, was successfully used in the Si-based and Si-Fe-based alloy. The calculation started from binary Si-Fe, Si-P and Fe-P systems, then the thermodynamic parameters of ternary systems could be derived based sub-binary systems. Using the activity coefficients of the elements in the Si-based alloys and the saturated vapor pressure of the pure substance of the components, mass fraction of P during vapor-liquid equilibrium can be calculated. The calculated thermodynamic parameters were compared with experimental data available in different publications, and it is found that the thermodynamic parameters calculated using MIVM model are in good agreement with the measured results. The calculated result shows that the mass fraction of phosphorus during vapor-liquid equilibrium of Si-Fe-P melt increases with the increasing phosphorus content and decreasing temperature. This is an important direction for experimental practice in vacuum or low-pressure EML refining of ferrosilicon for potential production of solar-grade silicon without significant vaporization loss of valuable element.

Jan 1, 2015

By J. M. Réjean Gagnon

"Quebec Cartier Mining Company is currently mining a low-grade iron ore deposit in northeastern Quebec. The Company is producing some 8,000,000 dry gross tons of concentrates per year, grading about 66 per cent iron. The pit, which is located on the keel or hinge line of a fold, will eventually be about 1,000 feet deep with a surface area of 8,000 by 2,600 feet. The most significant structural discontinuities in the mine are the natural bedding planes and secondary perpendicular joints. The exposed walls are subjected to a sub-Arctic climate and heavy blasting occurs approximately six times a month.QCM utilizes design and operating techniques to control rock fall. Steps are also being taken to analyze the ultimate over-all pit slope stability."

Jan 1, 1968

By Hans E. Madeisky, Bruce W. Downing

Abstract-The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: anorthosite-hosted magmatic sulfide nickel, dunite-hosted magmatic sulfide nickel, porphyry copper-gold, and volcanic-hosted high sulfidation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray fluorescence equipment, already used for grade control at many mine sites, could provide the wholerock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By Yongjun Peng, Yufan Mu, Rolf A. Lauten

"Chalcopyrite, a major source of copper, is commonly found associated with iron sulfides, particularly pyrite. The separation of chalcopyrite and pyrite by flotation is difficult due to the galvanic interactions between pyrite and chalcopyrite during grinding and flotation. Galvanic interactions may cause oxidation and dissolution of chalcopyrite, copper activation of pyrite and the formation of hydrophilic iron hydroxide coating. The overall effect may change the floatability of the components and lead to the misplacement of pyrite into chalcopyrite concentrate. The objective of this study was to investigate the effect of lignosulfonate-based biopolymers on the depression of pyrite in the flotation of chalcopyrite with xanthate as collector and the mechanism responsible for the selective depression of pyrite. The flotation results showed that biopolymers depressed the flotation of both copper-activated pyrite and chalcopyrite in single mineral flotation although to different extents. In the flotation of mixed mineral systems, biopolymers significantly depressed pyrite flotation but had a less influence on chalcopyrite flotation. The selective depression of pyrite by biopolymers was due to the preferential adsorption of biopolymers on copper-activated pyrite surface. Galvanic interactions between pyrite and chalcopyrite surfaces promoted copper activation on pyrite. Presence of cuprous ions on pyrite surface favored biopolymer adsorption by the formation of a complex between the cuprous ions and biopolymer molecules. The same galvanic interactions also facilitated chalcopyrite oxidation leading to the formation of hydrophobic polysulfide that enhanced the hydrophobicity on chalcopyrite surface. The biopolymer structure controlled the depression effect. The results showed that the biodegradable biopolymers are promising depressants for pyrite.INTRODUCTIONCopper sulfide minerals, such as chalcopyrite (CuFeS2), bornite (Cu5FeS4), chalcocite (Cu2S) and covellite (CuS), are the major mineral source for copper. They are often found finely interlocked with iron sulfides, especially pyrite (FeS2) (Owusu, Brito e Abreu, Skinner, Addai-Mensah, & Zanin, 2014). Pyrite, as the most abundant sulfide mineral, is perceived as gangue in most cases and should be removed from the associated sulfides to minimize its contamination of the copper concentrate (Owusu, Addai-Mensah, Fornasiero, & Zanin, 2013; Wang & Forssberg, 1991). The commonly used strategy to remove pyrite is flotation (Wang & Forssberg, 1991)."

Jan 1, 2016

By Hans E. Madeisky, Bruce W. Downing

The acid rock drainage (ARD) buffering capacity of mine waste is governed by its bulk chemical composition and its mineral assemblage. Conventional acid base accounting (ABA) tests can be used to predict short-term buffering, but should be used with caution to model or predict the long-term ARD buffering capacity of mine waste. ABA data for mine waste samples from four different deposit types: an orthosite-hosted magmatic sul?de nickel, dunite-hosted magmatic sul?denickel, porphyry copper-gold, and volcanic-hosted high sul?dation epithermal silver, were compared with whole-rock geochemical and petrographic data obtained from the same samples. Our objective was to devise and test a method of predicting ARD buffering capacity based on bulk chemistry and modal mineralogy. In other words, we developed a quantitative theoretical method for calculating neutralizing potential, relying on easily obtainable and relatively inexpensive whole-rock and sulfur XRF analyses, which could substitute for conventional ABA procedures in situations where these procedures are either too costly or too time consuming. For each deposit type, models were devised that reasonably approximate the net neutralization potential estimated by the ABA data obtained from laboratory tests. Once an appropriate model has been developed and tested, portable X-ray ?uorescence equipment, already used for grade control at many mine sites, could provide the whole-rock and sulfur analyses required to estimate the ARD potential of the waste material. Although this approach is not intended as a substitute for the legally mandated ABA test procedure, it could facilitate the timely and cost-effective management and mitigation of ARD at a mine site.

Jan 1, 1997

By M. B. Kime, A. T. Kaniki

"Grinding tests were conducted on an oxidized copper-cobalt ore using a pear-shaped ball mill. Twelve mono-sized ore fractions were prepared and wet ground batchwise. The mill was run for 0.5 to 30 min intervals. The shortest interval provided data more closely related to the breakage function (B) because less secondary breakage was hypothesized. Some selection function (S) and B parameters were determined. Remaining parameters were estimated using a population balance model simulator. To evaluate the kinetics model, an unsized ore sample was also milled. Predicted and measured particle size distributions (PSDs) agreed well, suggesting that S and B parameters can be used for continuous operation mass balances.RÉSUMÉ Des essais de broyage ont été menés sur un minerai oxydé de cuivre-cobalt à l’aide d’un broyeur à boulets piriforme. Douze fractions de minerai de dimension unique ont été préparés et broyés en voie humide en lots. Le broyeur était mis en route à des intervalles de 0,5 à 30 minutes. L’intervalle le plus court fournissait des données plus étroitement liées à la fonction d’abattage (B) car d’après l’hypothèse avancée, le besoin d’abattage secondaire était moindre. Certains paramètres de la fonction de sélection (S) et de B ont été déterminés ; les paramètres restants ont été estimés à l’aide d’un simulateur de modèle d’équilibre de population. Pour évaluer le modèle de cinétique, un échantillon de minerai non calibré a également été broyé. Les compositions granulométriques (PSD, de l’anglais particle size distributions) prévues et mesurées correspondaient bien, ce qui laisse penser que l’on peut se servir des paramètres S et B dans le cadre d’équilibrages massiques en fonctionnement continu. INTRODUCTIONSize reduction of solids is a very energy intensive and highly inefficient process. It consumes approximately 5% of the electricity produced worldwide (Rhodes, 1998), and more than 50% of the total energy used in mineral processing plants (Walkiewicz, Lindroth, & Clark, 1996). An increase in grinding efficiency can therefore result in significant reductions in operating costs. This often amounts to determining the optimal design configurations for milling an ore sample in a laboratory mill under standard conditions. Prior to optimizing the milling stage, the requirements for downstream processing in terms of particle size distribution (PSD) need to be understood because low liberation and overgrinding will lead to future problems. Once this is done, it is also important to clearly understand the breakage properties of the ore. The kinetics of size reduction in tumbling mills are often determined using two probabilistic functions: selection and breakage (Austin & Luckie, 1972). Knowledge of the selection and breakage functions also enables the prediction of the PSD for a given ore sample."

Jan 1, 2017

By Leslie McHattie

?Intelligent mine? conjures up a futuristic image of unmanned extractors and loaders working in harsh conditions in a remote lunar landscape. The promise of increasing mine fleet productivity and solving the problem labor shortages in mining regions can certainly be achieved today through remote controlled extraction and automated hauling. The technology is available and it doesn?t seem to be so much science fiction when Google?s self-driving cars hurtle down the freeway. ?Intelligent mining,? on the other hand, implies the application of information technology at every phase of the mining value chain, from exploration and geological modeling to equipment, operations and maintenance, and logistics and transportation. These are really industry-specific, enterprise-class software solutions focused on using information technology to support the business processes of mining and make them more efficient and effective. Overlaying the physical world with the digital or virtual world enables us to model and simulate our assets, giving us the ability to effectively design, build, and ultimately optimize the performance and reliability of our assets throughout the lifecycle. The digital asset, often a 3D model, is created initially during the engineering and construction phase, and is handed over to the operator before the mine goes into operation. Combined with geospatial or geographic information systems, the operator has a complete digital representation of the physical world, which forms the foundation for risk and performance management, along with compliance and regulatory reporting. Laser scanning and positioning technology can be used to create point clouds ? information models consisting of millions of data points ? which enable the visualization and representation of the ?as-operated? reality. But consider that once the mine is in operation, it throws off an endless stream of data in the form of performance and condition data from sensors and monitoring devices on fixed and mobile assets through networks, servers, and services. This ?big data? can be processed and analyzed to spot trends, help predict events, and formulate reliability strategies as early as the design stage (e.g., reliability-centered design). ?Intelligent mining? implies that massive amounts of data augment the reality of the physical mine, plant, and equipment. This embedded intelligence can be used to optimize operational efficiency, increase asset availability and utilization, improve safety and environmental integrity, and maximize return on investment. Lastly, the sweet spot for intelligent mining is seen in the convergence of consumerization and industrialization. The application of ?consumer? technologies that we use every day on our iPhones and Android devices, such as cameras, motion sensors, and positioning in an industrial context, are producing ?immersive? experiences. Overlaying the digital world on the physical world and connecting them accurately through intelligent positioning results in ?intelligent infrastructure,? which is safer and more sustainable. Bentley Systems works with many mining companies and engineering, procurement and construction companies involved in all aspects of mining infrastructure development. In fact, 10 of the top 20 mining companies ranked by market capitalization are users of Bentley software, including all of the top five. In addition, Bentley provides software solutions to the world?s leading engineering, procurement, and construction companies, as well as owner-operators, who design, build and operate the world?s infrastructure. Bentley?s solutions for mining and resource extraction industries help increase the efficiency of capital projects associated with the design, procurement, and construction of mines and processing plants, as well as the operation and maintenance of mining fleet and equipment.

Aug 1, 2013

By E P. Graham

Orebodies occur in an infinite variety of grades, shapes and sizes, and take many millions of years to grow. When extraction starts there is only one possible end -the mine sooner or later will run out of ore and shut down. If the mineral industry is to supply the ever increasing demands of modern civilizations, more and more metals must be found and mined. This will require a never-ending search for ore, and the development of every economic body, large or small. To justify the mining of a small orebody, it first of all must pay its way. If the size of the burden imposed by the capital cost estimates is not carefully worked out, an otherwise promising situation could be killed. The very nature of mining, as a transient industry, re-leases a steady stream of good used equipment, and the trained personnel to install and operate it. All manner of plans and layouts, which can be utilized at a new property, are available. Working these and other economies into the estimates will sometimes make enough difference to give a prospect the green light.

Jan 1, 1964

By D. H. Stonehouse

Of the f ive Canadian cement producing regions- Atlantic, Quebec, Ontario, Prairie and Pacific-Ontario has the greatest capacity and normally produces the most cement. However, during the last 5 years the greatest activity within the industry in Canada has been in the Prairie and Pacific regions where major capacity increases have taken place. Most Canadian cement companies produce normal Portland, high-earlystrength Portland and sulphate resisting Portland cements. Some companies also manufacture moderate Portland cement, and low-heat-of-hydration Portland cement. Escalating energy costs highlight the need for technology research into more energy-efficient equipment for the energy-intensive cement industry. The industry is well integrated and plants are well situated to support construction in Canada. Expansion into the United States has become common during the past decade.

Jan 1, 1984