Search Documents

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962

By Michael J. Miller

The demand and supply of wollastonite has gone through a dynamic period in the 1990's. A 10% -15% growth rate of demand stimulated interest in evaluating new projects. However, the mid-1990's brought declining prices for commodity applications and natural barriers to entry for technical applications, making many of these potential projects uneconomic. Successful projects that were brought to market were done so by incumbent producers. This work examines the competitive structure of the wollastonite market by evaluating the strategic decisions of the industry leader, NYCO Minerals Inc., and a new market entrant, Orleans Resources, in an attempt to identify the environmental threats and opportunities of this industry. Results suggest new entrants like Orleans Resources face significant entry barriers for technical applications, while NYCO Minerals could improve its profitability by having less exposure to commodity applications.

Jan 1, 1999

By Z. Hyder, A. Urquidez

"INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is located approximately 26 miles southeast of Carlsbad, New Mexico and is the nation’s first underground geologic repository for transuranic (TRU) and TRU-mixed waste (see Figure 1). The WIPP facility was opened for operation in 1999 when the first TRU waste shipment arrived at the WIPP facility for disposal.WIPP facility does not employ typical production aspects of a conventional mine. Instead, the mining focus is on the quality of the excavation to ensure safe disposal of TRU and TRU-mixed waste (Walls, 1991). GEOLOGY WIPP underground repository is mined within a 2,000 feet-thick bedded-halite formation (Salado Formation) (see Figure 2). The WIPP underground repository is located approximately 2,150 feet beneath the surface near the center of the Salado Formation. Geologic criterion and site-selection factors evaluated for the selection of the repository included topography, depth, thickness, lateral extent, lithology, stratigraphy, structure, erosion, dissolution, subsidence, surface water, aquifers, hydrologic transport, climatic fluctuations, manmade penetrations (U.S. Department of Energy, 1980).FACILITY DESIGN Profit did not play a major role in the WIPP’s conception like in a conventional mine. This was due to the extensive amount of additional regulations and safety controls that had to be built into the WIPP facility. Since it is nuclear and hazardous waste disposal facility, it must meet certain federal and state requirements for TRU-mixed waste. One of the major regulatory drivers for the WIPP facility is defined in the WIPP Land Withdrawal Act (LWA). One of the requirements in the WIPP LWA requires the DOE to submit documentation of continued compliance with Title 40 CFR Part 191, Subparts B, and C. These standards are regulated by the Environmental Protection Agency (EPA). The DOE must submit documentation of continued compliance (recertification) with these regulations every five years. In addition to the LWA, the Resource Conservation and Recovery Act (RCRA) is another major regulatory driver for the WIPP facility. Since the WIPP facility is categorized as a “Miscellaneous Unit” under 40 CFR, it must meet extensive environmental performance standards. These standards are defined in the WIPP Hazardous Waste Facility Permit (HWFP). The HWFP defines the terms and conditions that the Secretary of the New Mexico Environment Department has determined necessary to protect human health and the environment (U.S. Department of Energy and Nuclear Waste Partnership LLC, 2015)."

Jan 1, 2017

By D. Kruse

Top-down constructed large-diameter (up to 90 m or 300 ft) shaft design and constructability issues present an interesting suite of challenges and opportunities highlighted in this paper. The study covers 2D and 3D finite element models used to analyze various failure modes, evaluate the shaft liner and internal structures' response to seismic loading, assist in segment design and assess final structural design tradeoffs. Efforts to achieve economic advantage over conventional heavy civil practices have prompted innovative solutions for ring and segment design, ring build assembly and annulus backfill grouting. Intended for soft ground conditions, relationships between soil parameters and structure design are also explored. Mining Engineering, 2011, Vol. 63, No. 9, pp. 81-88. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By G. Nash

Despite further declines in production for some producers, 1986 proved to be a landmark year for the asbestos industry. The key event was the adoption of The Asbestos Convention by the Inter- national Labour Organization (ILO) and its 150 member countries. The document, entitled "Safety in the Use of Asbestos", reaffirms the international consensus on the "controlled-use" approach to chrysotile asbestos regulation. The decision of the ILO has come at a critical point in time. It represents a major turning point and provides an important building block for the long term future of the asbestos industry.

Jan 1, 1987

By Mehmet Bugdayci, Onuralp Yücel, Yeliz Demiray Cucurachi, Ahmet Turan

The production of strontium (Sr) metal from its oxide via an aluminothermic process under 1–5 mbar pressure was examined in this study. SrO of 99%purity by weight was used in the experiments. The effects of stoichiometry and the duration of the process on the efficiency ratio of the metallic strontium were examined. The effects of functional additives (BaO, CaO, CaC2) were also examined. Characterization was carried out using X-ray diffraction spectrometry (XRD), atomic absorption spectrometry (AAS) and flame photometry techniques. The highest Sr efficiency ratio obtained was 96.89% in the experiment conducted at 1250 °C with 300% Al stoichiometry and 300% BaO stoichiometry.

Aug 7, 2020

By Van E. Housman, Stephen D. Hoffman

The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA), also known as "Superfund", requires a listing of sites that have known releases or threatened releases of hazardous substances, pollutants, or contaminants throughout the U.S. When EPA determines that a significant threat exists, it places the worst contaminated sites on the National Priorities List (NPL). CERCLA provides EPA broad authority to clean up hazardous sites that threaten human health and the environment. There are currently 52 sites on the NPL that were placed on the list because of high human health or environmental risk as a result of non-coal mineral extraction, beneficiation, or processing operations. This list covers mining sectors from aluminum to zinc. While some of these sites were abandoned, many are still operating. (There are additional mine sites that have been recently proposed to be included on the NPL that are not included in this paper.) EPA is continuing to develop a mining program to address human health and environmental threats from active non-coal mines. EPA has performed a comprehensive study to assess the waste management practices at all of the 52 mine sites on the NPL. In addition, EPA is continuing to collect information on the specific mining sectors (i.e., gold, copper) that represent many of the NPL mine sites. One of the goals of this effort is to attempt to identify the types of mining practices that lead to human health and environmental problems at the NPL mine site. EPA estimates that there are currently 500 to 1,000 active mines (not including placer operations). While some mining NPL sites began operations before the turn of the century, only a handful of the NPL mines entirely ceased operations prior to 1970. Of the 52 NPL sites studied by EPA, 12 are currently active. By definition, these mines represent current mining practices. Approximately 17 additional NPL mines that ceased operations between 1970 and 1990 represent some degree of current mining practices. Therefore, at best, less than half on the 52 NPL mine sites can be said to definitely represent past mining practices. Although some mining waste management practices have changed over time, the basic technology for extraction and beneficiation of mineral ores have remained fairly constant over the last fifty years. While the use of acid to leach copper dumps, the use of cyanide to leach gold in heaps, and the spread of solvent extraction techniques has changed some aspects of mining, the basic operation of removing ore from the ground and concentrating it through beneficiation has remained fundamentally the same as when most of the non-active

Jan 1, 1992

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll in the US coal mining industry. Recent health surveillance data indicates that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied in order to reduce dust levels. An overview ofCWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

Jul 30, 2020

By G. V. Campbell, O. T. Holdsworth, M. G. Nelson

A senior design project is required by all accredited mining engineering degree programs. Often referred to as the capstone of a student’s education, this project is expected to include all the important components of the preliminary economic assessment of a mineral prospect, including orebody modeling, grade and reserve estimation, selection of mining and processing methods, preliminary mine design, access and utilities, environmental compliance and reclamation, and financial analysis. Two of the authors (Campbell and Holdsworth) completed a senior project in 2021. They analyzed the Akie zinc deposit located in Canada. This paper summarizes the economic analysis portion of that project. The two primary objectives of this economic analysis were risk reduction and integration of economics and engineering. Addressing risk is important as risk is one of the primary concerns in mining investments. Risk reduction was the primary concern through the entirety of this economic analysis. Integration of financial analysis and engineering design was the first component of a risk reduction design. This allowed for financial and engineering design to be optimized in conjunction with one another. This produced benefits from both a financial and an engineering prospective. From a market, economic, and financial risk perspective, risk was reduced by forecasting multiple metal price scenarios, and then addressing the Akie project’s economic viability at each price point. Lastly, risk was address through consideration of nontraditional financing options. The project also sought to minimize financial and human capital risk, by proposing mutually beneficial cooperative social relationships and favorable work, schedules. Description of that work is not included in this paper.

Mar 2, 2022

By D. R. Gehring

Effective project management is an excellent technique for meeting a goal through set, well-defined objectives. Even though project management is successfully used throughout the world in various construction projects, underground mining has unique characteristics that require approaches that vary from classical project management theory. Typically, a project includes four main stages: definition, planning, implementation and control. Definition and planning are often the most overlooked stages, but are arguably the most important. This paper addresses practical techniques for the definition and planning of projects for underground construction.

Jan 1, 1996

By M. E. Kuchta

Surface coal mine design can be facilitated with the use of an interactive graphics personal computer program. This mineral inventory and planning program (POLY CALC) is described and its use is illustrated with a case study. The case study deals with investigating a stripping sequence and associated dragline stripping requirements.

Jan 1, 1986

By Mo Wanqiang

Equivalent-pressure ventilation is a method of balancing the air pressure between a productive face and its gob to extinguish fires and prevent the infiltration of toxic gases, so that the production of the face can be maintained. The method was successfully applied in Coal Mine No. 1 of Hebi Coal Mining Administration in north-central China. In this article, a practical application of the equivalent-pressure method to prevent carbon monoxide from entering an active longwall face adjacent to a fire breeding area is described, and four steps to achieve equivalent-pressure are discussed. The reliability of using this method and measures to maintain the equivalent-pressure are analyzed. It was observed that this method could maintain high production level while no sacrificing safety at the longwall face.

Jan 1, 1984

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By d&apos, I. J. Agati

The stockpiling and reclaiming of bulk materials can be a challenging task for engineers seeking the optimum solution for plant needs, reliability, and at lowest unit cost. The objective of this paper will be to expose advantages, disadvantages and limitations of many storage and reclaiming systems to the responsible engineer and management. The paper will emphasize the practical aspect of stockpiling and reclaiming methods. Many valuable and interesting papers are available dealing with the theoretical viewpoint and application of a particular manufacturer's machine. Several of these are mentioned in the bibliography. As many practical parameters as possible will be given. After twenty years in the field of designing and selling bulk materials handling systems, the needs of the user and the plant are recognized and reasonably understood. This paper cannot give solutions to all problems In this vast field but will stress practical applications and examples of various installations. The evolution of advancements in materials handling is based upon not only technological innovations, but learning from many experiences of others and utilizing them as stepping stones to improved installations.

Jan 1, 1969

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice-chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor. Candace Trimble, member SME, of Oil-Dri Corporation of America, is chair of the Industrial Minerals and Aggregates Division?s Technical Committee.

Jan 1, 2012

By Bradford F. Townsend, Matthew E. Fowler, Michael F. Smithson, Lawrence R. Eckert

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2010

By Bill Mariucci, Gary Almeraris

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2009