Search Documents

By D van der Merwe

Tracers of known densities are used world wide in coal processing plants to evaluate plant performance. Tracers are added to the feed stream and are counted after being recovered from the product and discard streams to determine partition curves. The need to recover the tracers can be eliminated by adding radio frequency identification tags to the tracers. Readers mounted on the product and discard streams record the passing RF tracers and produce the partition curve instantly. Tests were performed with three different shaped tracers at different collieries on cyclones ranging from 510mm to 800mm in diameter. Sink and float analyses of coal samples were used to compare conventional partition curves to partition curves obtained by using RF tracers. The average amount of tracers recorded was 78% of tracers in the feed. The results indicate that the stone shaped tracers represent the results from the sink-float analyses the best. The results suggest that RF tracers can be used to evaluate cyclone circuits in the coal industry and will make it possible to evaluate a coal circuit?s efficiency without stopping a plant and waiting for laboratory analyses. Keywords Coal tracers, partition curve, radio frequency tracer, RFID

Jan 1, 2006

Rutile Beach Sand from Hard Rock

Sep 13, 2010

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

By M. Maccagni, J. Nielsen

"Engitec developed the EZINEX® Technology some years ago to recover zinc from oxidized secondary sources. This process works at neutral pH and can take into solution any kind of metal, but iron is rejected and remains in the leach residue. Engitec has also developed the FLUOBORATE System, which is able to recover lead and copper from relevant concentrates. Some iron is leached into solution, but it is controlled through a solution purification bleed treatment. In this paper, we present the two above mentioned technologies. They are very different with regards to the chemical environments and the methods used to control the build-up of iron in solution, but both systems are suitable to treat iron bearing feeds.INTRODUCTIONIn the design of hydrometallurgical processes, the most important issues are the water balance, the filtration and the control of impurities. This is particularly important when the process includes an electrowinning unit. Iron has been one of the most problematic elements to remove, especially in acidic environments.Engitec Technologies has developed several hydrometallurgical processes divided in two different electrolyte lines: the Fluoborate Technology for the recovery of lead and copper from primary and secondary sources and the Ammonium Chloride System based on a chloride electrolyte for the recovery of different non-ferrous metals, among which zinc and lead are the most important. In both cases, iron is present in the feed and needs to be eliminated from the solution. It is not a problem for the quality of the metal produced, but when present in solution, it consumes the basic electrolyte reducing its free concentration which is very important both for both the leaching and electrowinning unit operations. Both process systems are very peculiar, the fluoborate case being much more intriguing."

Jan 1, 2016

By Madsen I. C, Langberg D. E

Recent advances in X-ray diffraction (XRD) technology have made it possible to conduct powder XRD measurements on samples at high temperatures during reaction. State-of-the-art detectors are now capable of rapidly acquiring diffraction patterns across a wide angular range (typically 120"20) enabling phase transformation rates to be measured directly during sample reaction. In this study, the phase transformations during the reduction of hematite to metallic iron by five per cent hydro ºen in nitrogen gas mixtures, were measured in situ between 500 - 700 C. Complete X-ray diffraction patterns were acquired within 15 seconds every one minute, enabling direct measurement of the transient phase abundances during the reaction. The data were quantitatively analysed by the Rietveld method to yield the abundances of hematite, magnetite, wustite and metallic iron, as functions of time during the reduction process. A first-order reactions-in-series model was proposed, and the reaction rate constants and activation energy were determined from the time-dependent phase abundance data.

Jan 1, 1999

The rush for alternate iron-units in the last few years spurred a true outbreak of new alternate iron units projects many of them incorporating new process in what can be classified as the.most fruitful and innovative technology outburst, in the steel industry, in decades In a recent paper we focused on what would be, in our opinion, the ultimate targets of the use of alternate iron-units by mini-mills: 1. to improve quality, 2. to reduce cost, 3. to increase plant productivity, and 4. to improve `supplyability'. With these objectives in mind liquid hot-metal, among all possible scrap substitutes, has been proven to be by far the best. This conclusion stems from many different authors who have reviewed the `value in use' of hot-metal against other alternate iron units and measured its impact on steel-shop productivity and cost (Figure 1).

Jan 1, 1999

By U. Weber

The effect of grinding media performance on milling and operational behaviour was demonstrated under different selected conditions of calcium carbonate slurry milling. A variety of grinding media materials and bead sizes, along with two different stirrer tip speeds, were used in the grinding process to generate a particle size reduction of the calcium carbonate (CaCO3). To determine the optimum milling parameters the collected test data were used to calculate and evaluate specific energy as well as stress intensity under different milling conditions. Keywords: Grinding, mill media, high energy mills, industrial minerals, precious metals.

Jan 1, 2010

By P. A. Witt

"Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located 75 km southwest of Kamloops, British Columbia (Fig. 1).The ore is situated within a porphyry copper deposit and is mined at a rate of 135,000 mt/day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 people and is planned to operate until 2009. The operation is a partnership between Teck Cominco (63.9%), BHP Billiton (33.6%), and others (2.5%). Management is shared by the two principal owners and directed by a management committee."

Jan 1, 2005

By Kanau JL, Kilgour I

This paper describes the metallurgical processes at the 80 000tpd Ok Tedi Mining Limited concentrator, which treats copper- gold ore by single-stage crushing, SAG and ball milling and flotation to produce over 500 000tpa of concentrate. Plant and process developments, including installation of column cells, reduction of fluorine in concentrate, use of sulphidisation and process control improve- ments are also discussed.

Jan 1, 1991

While SME is hosting its Annual Meeting at the Phoenix Convention Center, Feb. 28 to March 3, one of the finest collections of mining history will be on display just 15 blocks away at the Arizona Mining and Mineral Museum. Inside the museum, visitors will be treated to a treasure trove of minerals, gems, me¬teorites, rocks, fossils, mining artifacts, historical exhibits and interactive displays on modern mining. The museum is located at 1502 West Washington. For SME Annual Meeting attendees, this is a free, eight-minute Dash bus ride 15 blocks west of the Phoenix Convention Center.

Jan 1, 2010

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

Statistics on the imports of industrial minerals into the EECshow that the traded volume in 1987 is approximately 23 million tonnes.The following table documents the imported quantities on the most important industrial minerals.

Jan 1, 1989

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By K. E. Robinson

Appendix A is an abridged extract of the report prepared by the Geotechnical and Structural Engineering Society of Idaho, and presents the results of their one-year study to evaluate the feasibility of disposing mill tailings by landfill construction. Appendix B describes the field and laboratory testing program completed by RDM to assess the effectiveness of a soil (slimes) liner as a means of seepage control to reduce the introduction of contaminants into the local ground water regime. Appendix C presents a summary of a thesis by Lawrence Martin on the analysis of the acid production potential of mill tailings, and the results of geotechnical testing of mill tailings completed by ROM. Appendix D describes potential landfill sites identified within the study area, the development of these sites to meet the present needs of the mining industry and the future requirements of the community is described. Appendix E summarizes the main legislation impacting on tailings disposal. Appendix F discusses the environmental and socio-economic factors that should be considered.

Jan 1, 1981

By Andrew A. A, Hamilton P. J

Constraints on pore water evolution in the aquifers of a sedimentary basin may be realised through stable isotope analyses of present day waters, and their comparison with water compositions calculated to have been in isotope equilibrium with the products of diagenesis during burial. Integrated with detailed petrographic observations, and thermal, structural and stratigraphic analyses, fluid migration patterns at various stages in a basin's history can be identified. This has important implications for modelling basin hydrology, hydrocarbon distribution, and reservoir quality in the Latrobe Group, Gippsland Basin, and oil-prone successions Elsewhere.

Jan 1, 1992

By Thomas Kuhn, Carsten Ruehlemann, Christina Heller, Anna Wegorzewski

The commercial extraction of metals from manganese nodules on an industrial scale requires more than 50% of the investment necessary to realize manganese nodule mining. This is mainly due to the fact that a completely new metallurgical processing scheme for the extraction of both base metals (Ni, Cu, Co) and high-tech metals (Mo, Li, Ga) has to be developed and upgraded to industrial scale. There are a number of conventional processing technologies that combine hydro- and pyro-metallurgical approaches such as the INCO and CUPRION processes which have been developed in the 1970s and 1980s. Today, new approaches based on selective leaching with chelating agents and bioleaching try to minimize energy consumption and waste production. All of these extraction methods require knowledge how the metals are structurally bound in the manganese oxides. In this contribution we will review the current knowledge about the mineralogy of iron and manganese minerals in the different marine oxide deposits, present our results, and discuss the possible consequences for metal extraction.

Sep 1, 2014

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By E. J. Sun

The ADS system was developed to reduce accidents related to haul trucks operating under low visibility conditions in surface mining and construction sites, which is based on the GPS, mesh-wireless networks, and the Google-Earth 3D graphic engine as the graphic interface and mine-mapping server. This system has the capability to pin-point and track vehicles in real time using a 3D interface, which is based on user-based AutoCAD mine maps using the Google-Earth graphics interface. All equipped vehicles are shown in a 3D mine map stored in a local server through a wireless network. When low visibility conditions are present, the system indicates available exit/escape routes for driver safety. The research results indicate that the ADS system potentially increases reliability and reduces uncertainty in open pit mining operations by customizing the local 3D digital mining map, constructing the truck 3D models, tracking vehicles in real time using a 3D interface and indicating available escape routes for driver safety.

Oct 1, 2009

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016