Search Documents

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

The history of mining is rightly proud of its achievements in improving productivity and cost improvements over the years. No matter what measure is used, tonnes per manhour, cost per tonne, etc vast improvements have been made over the last hundred years. In fact over the last ten years in Australian coal mines raw coal output per employee has increased by 60 per cent. When one examines why these improvements have taken place the principal reasons have been technological advancement in mining equipment, excavator and dump truck capacity increases, longwall and continuous miners continually improving in reliability and size. Of course all these improvements are correlated to an increase in capital cost. Even with the above-mentioned advances the pressure for increased performance is as strong as ever. The international mining and mineral-processing sector is currently operating in a recessive market with some traditional commodities, eg gold trading at 20 year lows. During recessive times senior management will demand greater returns on capital employed: the obvious choices being reducing costs or increasing throughput. In addition, head office environments will often place a capital freeze on operational management so the opportunity to take advantage of technological change is not available. The challenge is, therefore, to increase throughput and cut costs without the need for capital. The answer is to optimise the existing labour and plant. If done systematically a result in productivity improvement, in our experience, as high as 45 per cent can be achieved with the average across South East Asia and Australasia being 21 - 23 per cent. The intention of this paper is to present a systematic approach to labour and machine utilisation thereby gaining the greatest possible return on the existing capital base.

Jan 1, 1999

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Nilabjendu Ghosh, Satyendra Kumar Singh, Gautam Banerjee, Harshit Agrawal

High-production methods like longwall mining with hydraulic powered supports are necessary to increase underground coal production in India. Longwall mining had a mixed success record for Indian geo-mining conditions. In this paper, an analysis is presented to optimally design an array of chain pillars in multi-seam longwall mining panels in the deepest coal mine in India. The study found that a chain pillar of 80-m width and 195-m length is necessary for long-term stability without any reinforcement. It was also observed that an optimum chain pillar can be designed by providing suitable side reinforcement (side bolting) which will reduce the chain pillar dimensions to 55-m width and 160-m length. Optimum design of chain pillars will reduce the coal locked up in these chain pillars by ~ 77%. This will also reduce the gestation period of longwall mining panel development. This paper also evaluates the maximum tensile subsidence strain induced at the surface and finds that the values are within the safe working limit of 3 mm/m. Thus, this paper finds direct application in the design of future multi-seam retreating longwall mining panels in Indian geo-mining conditions.

By Steve Kral

A near-record crowd of mining history enthusiasts made the trip to Leadville, CO in September to attend the National Mining Hall of Fame and Museum’s 19th induction banquet. Dressed in Victorian garb, black tie tuxedos and formal gowns, the 268 people honored four distinguished men who made a lasting impact on the U.S. mining industry. They joined 188 other inductees. The first induction banquet took place in 1988, with about 500 people attending.

Jan 1, 2007

By Milson de Andrade Júnior

A Central Termoelétrica número 2 (CTE#2) possui três caldeiras de alta pressão que utilizam principalmente os combustíveis residuais dos processos siderúrgicos, com destaque para o gás de alto-forno (GAF), o qual está disponível em grande volume e com baixo custo. Como o GAF possui baixo valor calorífico, ele é enriquecido em duas misturadoras com gás de aciaria (GLD) e na ausência ou limitação deste, com gás natural (GN). A partir de 2014, devido a problemas com o gasômetro de GLD, passou-se a utilizar o GN com frequência para fazer o enriquecimento do GAF, o que gerava significativo impacto no custo do vapor devido o alto custo do GN. O sistema de injeção de GN nas misturadoras era controlado de forma manual e praticamente não acompanhava as variações no poder calorífico (PCI) do GAF. Percebeu-se que seria possível implementar um sistema de controle para as injeções que levasse em consideração o PCI do GAF, reduzindo o consumo de GN quando o PCI estivesse mais alto e aumentando o consumo quando o PCI estivesse mais baixo. Após a implementação deste sistema houve uma significativa redução no consumo médio de gás natural para enriquecimento do gás de alto-forno na CTE#2.

Aug 17, 2017

By Paulo Vinícius Souza da Conceição

A demanda por aços com baixos teores de enxofre tem propiciado o aprimoramento das técnicas de dessulfuração de gusa. O presente trabalho tem como o objetivo mostrar, através de um modelo em água, a influência da injeção auxiliar de gás através do impeller S.I.R.A.M sobre o tempo de mistura no processo do Reator Kanbara (KR) e sobre a área de contato desse gás com o líquido. Diferentes velocidades de rotação do impeller, vazões de gás injetado e pontos de injeção foram avaliados. Os resultados obtidos foram comparados com a condição de não injeção de gás. Observou-se que a injeção de gás é capaz de reduzir o tempo total de mistura.

Aug 17, 2017

By Bruno Valladão Fraga

Esse trabalho tem como objetivo apresentar a estratégia adotada para a migração dos sistemas de otimização de processo dos três Altos Fornos da ArcelorMittal Tubarão. O desenvolvimento dos novos sistemas é baseado no Plano Diretor de Tecnologia de Automação (PDTA) que definiu a arquitetura, tecnologias e elaborou o Framework como base das aplicações. Para a migração dos sistemas foi elaborada uma especificação detalhada de todos os módulos e funcionalidades existentes, permitindo dessa forma a criação de uma camada com as principais regras de negócios relativas ao processo para serem reutilizados em todos os Altos Fornos. Essa camada deu origem ao Framework dos Altos Fornos. Os resultados obtidos já podem ser vistos nos três sistemas migrados para a nova plataforma, com um alto desempenho e estabilidade, garantido dessa forma a segurança operacional objetivada.

Aug 17, 2017

By Cleciano Berlando Miranda de Oliveira

A Engenharia de manutenção em equipamentos siderúrgicos da CSN vem desenvolvendo habilidade e aplicando com ótimos resultados os recursos computacionais avançados com modelagem 3D e simulação numérica através de métodos de elementos finitos. Estes recursos estão se tornado um diferencial na dinâmica dos trabalhos de manutenção com foco em análises de falhas crônicas e respostas rápidas para a solução dos problemas. Caracterizando e estratificando as falhas é possível desenvolver melhorias e defendê-las com maior assertividade e credibilidade. O recurso computacional já está no mercado há tempos e a CSN está na vanguarda na formação de sua equipe própria com um nível avançado e grande potencial para otimização de resultados da engenharia de manutenção de equipamentos (GEM) da CSN-UPV. A missão principal é agregar valor aos ativos, com agilidade e confiabilidade na caracterização de oportunidades de melhorias dos projetos ou restabelecimento funcional. Trilhando um caminho contínuo no que tange a qualidade e assertividade nas soluções de problemas de equipamentos mecânicos, serão apresentados alguns casos de sucesso que estão em desenvolvimento e um projeto de melhoria nos rolos de entrada de um laminador de encruamento, localizado na saída da linha de recozimento contínuo para chapas número um (LRCC#1). Estes rolos apresentavam fraturas com frequências mensais gerando paradas de mais de 8 horas e, após os estudos e implantação do projeto em 2012, não houve mais registros de paradas por falhas nos rolos. O projeto foi padronizado e multiplicado para os demais rolos da LRCC#1 e outras linhas com projetos semelhantes.

Aug 17, 2017

By Deyve Drengson Carneiro Vieira

O objetivo desse trabalho é identificar a eficiência térmica do glendon de uma empresa do setor siderúrgico mineiro. Tendo em vista que quanto mais eficiente for o equipamento, maior é o aproveitamento da energia fornecida e também menor é o consumo de carvão vegetal no alto-forno, reduzindo o OPEX. Este trabalho foi um estudo de caso baseado na análise de diferentes referências bibliográficas e através de estudos prévios e dados reais. O glendon em estudo apresentou eficiência térmica de 53,1%. Estudos mais recentes apresentaram eficiência de 67,4% utilizando chicanas no interior do glendon alterando o fluxo gasoso. O combustível do glendon é o gás do topo do alto-forno recuperado. A energia proveniente da combustão representa 89% da entrada de energia no regenerador, o que mostra quão importante é uma queima estável do GAF no glendon. Observou-se um desperdício de 45,5% da energia de combustão que saem pelos gases na chaminé, sendo uma oportunidade futura de estudo para reaproveitamento dessa energia

Aug 17, 2017

By Sunil Katharia

In February 2016, the upgraded Blast Furnace 1 of JSW Steel Limited (JSW) at its Vijayanagar Steel Plant was blown in after a 6 months shutdown in which the whole furnace was rebuilt on the existing foundation and within the existing tower structure. Despite several plant constraints it was possible to increase the furnace inner volume by 85% - reaching 2307 m3 from existing 1250m3. The upgradation project covered the stockhouse and its dedusting system, top charging system, furnace profile, furnace cooling system, casthouse and its dedusting system, slag granulation plant, pulverized coal injection plant, hot blast system and gas cleaning plant – with major interventions in order to cope up with the changed operating conditions. The total scope of the project was split by JSW into several packages, all based on design data provided by Paul Wurth. JSW was responsible for coordinating the local subcontractors along with Paul Wurth which has been appointed as main technology supplier in charge of complete basic and selected detail engineering in the key areas and of the supply of core equipment such as the Bell-less Top®, copper staves, GCP key items and TMT casthouse machines. The main design concept and the key points of the project such as optimization of project ROI, advanced erection concepts as well as a summary of the operating results are presented confirming JSW “BF1” upgradation as one latest examples of the current state of the art in the revamping projects.

Aug 17, 2017

By Alexandre Dolabella Resende

O estudo do padrão de fluxo do aço no molde de lingotamento contínuo é de grande importância para a siderurgia, uma vez que permite compreender como as variáveis de processo afetam a qualidade do aço produzido. Existem diversas técnicas, numéricas ou experimentais, utilizadas para realizar esses estudos. Este trabalho apresenta um estudo de simulação numérica, que tem como objetivo avaliar a influência da fração de argônio injetada no sistema no padrão de fluxo do aço no molde de lingotamento de placas. As condições de processo simuladas foram obtidas de diversas máquinas de lingotamento, com diferentes vazões de aço e argônio injetado. Os resultados numéricos foram validados através de um método experimental denominado “Nail Board”. Após a realização do estudo, foram constatadas consideráveis alterações do padrão de fluxo devido à variação da fração volumétrica do argônio injetado no sistema.

Aug 17, 2017

By G. Huang, S. Vytla

Computational fluid dynamics (CFD) is a continually developing numerical technique by which complex fluid flow problems can be solved on computers. To be able to transfer CFD expertise to analyze and design a face-ventilation system, a comprehensive validation study of current CFD tools against mining-related benchmark experiments is required. In the last four years, such studies, funded by National In¬stitute for Occupational Safety and Health (NIOSH) under Grant #R01 CCR415822, were conducted in the Department of Mining Engineering at the University of Kentucky. A wide array of ventilation schemes and mining configurations were considered. Recently, an additional study was performed in cooperation with the NIOSH Pittsburgh Research Laboratory. This study was dedicated to the methane behavior in the empty (containing no equipment) face area with a blowing curtain and a 10. 7-m (35-ft) setback. In this paper, the authors present and discuss the computer-simulation data and compare them with data collected during the laboratory studies at the NIOSH lab.

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By D. J. Thorkelson

New data indicate Wernecke Breccia-associated iron oxide copper-gold (IOCG) deposits likely formed from moderate-temperature, high-salinity, non-magmatic brines. The breccias formed in an area underlain by a sedimentary sequence that locally contained evaporites (potential source of chloride and possibly sulfur) and was thick enough to produce elevated fluid temperatures. Metals (Fe, Cu, Co, U) were probably derived from host strata, transported as chloride complexes, and precipitated due to changes in fluid temperature and pressure during brecciation. These new data suggest that the spectrum of genetic models for IOCG deposits that typically invoke formation from magmatic or hybrid magmatic-non-magmatic fluids should be expanded to include those systems that formed in a non-magmatic environment. Modifications to the definition of IOCG systems are proposed that reflect the degree of involvement of magmatic and/or non-magmatic fluids and the nature of the mineralizing environment. A division into magmatic, non-magmatic, and hybrid magmatic-non-magmatic IOCG types is suggested. Typical magmatic end-member IOCG deposits include Lightning Creek and Eloise, Australia. Hybrid magmatic-nonmagmatic IOCG examples include Ernest Henry and Olympic Dam, Australia. The Wernecke Breccia and Redbank deposits are suggested as possible representatives of non-magmatic IOCG end members. Endmember magmatic IOCG deposits have similarities to some porphyry deposits, whereas non-magmatic IOCG end members share characteristic with some sediment-hosted Cu deposits, suggesting that the range of IOCG deposits may form a link between intrusive- and sediment-related deposits

Jan 1, 2007

By J. Goyman, K. R. Rawling

"1.1 Location and Transportation ServicesNanisivik Mines Ltd. is located at latitude 73°, 3,200 km north of Montreal and 700 km north of the Arctic circle, on the south side of Strathcona Sound, which is an arm of Admiralty Inlet, in Northern Baffin Island. The orebody and mill site are 4 km distant from Strathcona Sound which provides deep water anchorage for ocean transportation of concentrate to Europe during the short northern shipping season from mid-July to mid-October.The operations and the resident community have direct jet aircraft service from Montreal two days per week, and local nights connect with other Arctic communities in the northern Baffin region. Bulk supplies and general cargo are delivered in the summer shipping season.1.2 HistoryThe Texas Gulf Sulphur Company, now Kidd Creek Mines Limited, staked claims in the Nanisivik area in 1957 and carried out exploration through to 1968. After the Kidd Creek orebody was found, Texas Gulf optioned the property in 1972 to Mineral Resources International Inc. (MRI), which undertook further exploration and completed a feasibility study.Nanisivik Mines Ltd. was formed in 1975, with MRI as the majority shareholder and minority shareholdings held by Metallgesellschaft, Billiton and Texas Gulf. Strathcona Mineral Services Limited was retained to manage the project during both the construction and operational phases."

Jan 1, 1984

Development of Grindability Tests Based on Direct Measurement of Energy Nowadays, for the characterisation of the grindability different grindability indices - Bond-work index (Wi), Hardgrove Grindability Index (HGI) or Zeisel specific grindability (Wt) - are used. Generally, the grindability tests are carried out under relatively simplified circumstances, in a special dry batch mill with defined feed size material until prescribed conditions are reached at room temperature. However, in the fine- and ultra fine grinding, which is a frequent task (fly ash, tailings, alumina, etc), a fine material (<50 - 200 ¦m) is usually ground down to the few micrometers. The conventional grindability testing methods and apparatuses (Bond-, Hardgrove-, Zeisel-processes) for their determination, although, are not suitable directly to measure the grindability of such fine materials, since the maximal particle size of the feed material (0.5 - 3 mm) to be tested is much higher. One of the important goals of the research carried out in our Institute was to develop the novel grindability testing methods, which are suitable for the fine and ultra fine grinding, and additionally provide the possibility for the fast determination of the grindability. In order to realise the above aim the conventional Bond- and Hardgrove- mills were modified in order to directly measure the grinding work. In particular, the Hardgrove-mill was equipped with a simple torque-meter (load cell). The Bond-mill was rigged with a digital electric power measurer. The systematic experiments were carried out parallel in both mills using the conventional and the developed methods. Finally the results of both were compared. The measuring results have proved that the Bond-work index can be determined based on the developed methods. The new grindability testing methods were applied successfully in several industrial research tasks for the determination of the specific grinding energy and the Bond-work index. These methods can be also used in the industrial practice for the control of the grinding process.

Sep 13, 2010

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

By Others, C. M. Weld

During the past two years the Bureau of Mines has issued a series of mimeographed reports giving the results of research work and experiments conducted as part of its war minerals investigations. In this bulletin the reports on manganese are presented, which range in scope from the beneficiation of the ore to the utilization of the metal. The bulletin is in eleven chapters, each comprising a separate report, arranged in the order given below. 1. General information regarding manganese, by C. M. Weld. 2. Uses of manganese other than in steel making, by W. C. Phalen. 3. Problems involved in the concentration and utilization of domestic low-grade manganese ores, by Edmund Newton. 4. Preparation of manganese ore, by W. R. Crane. 5. Leaching of manganese ores with sulphur dioxide, by C. E. Van Barneveld. 6. The Jones process for concentrating manganese ores; results of laboratory investigations, by Peter Christianson and W. H. Hunter. 7. Cost of producing ferromanganese ores, by C. M. Weld and W. R. Crane. 8. Production of manganese alloys in the blast furnace, by P. H. Royster. 9. National importance of allocating low-ash coke to the man- ganese-alloy furnaces, by P. H. Royster. 10. Electric smelting of domestic manganese ores, by H. W. Gillett and C. E. Williams. 11. Use of manganese alloys in open-hearth steel practice, by Samuel L. Hoyt. As each chapter was originally prepared as a unit, there is neces- sarily some duplication and overlapping. With certain exceptions, however, each paper is reproduced in practically its original form. In chapter 1, covering certain general phases of the industry, such as uses, specifications, prices, and statistics, the subject matter has been somewhat modified in view of changes in conditions.About 95 per cent of the manganese consumed in the United States goes into the manufacture of steel. The remaining 5 per cent is used in a number of minor industries, the chief of which is the manufacture of dry cells. These minor uses are described in chapter 2. No discussion of the geology of manganese eres is presented, but a short bibliography on the subject is appended. With few excep- tions the manganese deposits of the United States are irregular, pockety, and uncertain. Largely for this reason, mining methods are crude and hardly warrant descriptions. The concentration of manganese ores, however, is an important problem and involves some details not common to other ores. Chapter 3 discusses the concentration and utilization of low-grade ones, notes the relationship of concentration to metallurgical prao- tices, outlines concentrating processes, and treats of commercial problems. In general, as regards concentration methods, manganese ores may be divided into two groups, as follows: (1) Ores permitting mechanical separation of the manganese minerals and the gangue, and (2) ores in which the manganese minerals and the gangues are so intimately associated that separation requires some hydrometal- lurgical or pyrometallurgical process. Heretofore, attention has been confined almost wholly to mechanical separation, chiefly by gravity. In fact, so far as known, all production of concentrates has been by wet gravity methods, although during the war some companies investigated the commercial pessibilities of magnetic separation and reported favorable results, the construction of one magnetic con- centration mill being started. The usual wet gravity methods are described in chapter 4. During the war, the Bureau of Mines undertook investigations of methods applicable to ores of group 2. A hydrometallurgical process involving leaching with sulphur dioxide was studied at the mining experiment station of the bureau at Tucson, Ariz. The results of this work, presented in chapter 5, indicate that the process is metallurgically feasible but the cost makes it unattractive. The results of an investigation of a pyrometallurgical process known as the Jones process are presented in chapter 6. The process, which is still in the experimental stage, was found to be metal- lurgically sound. The manganese product is not a concentrate but an alloy, made directly from a lean unconcentrated ore. The custom- ary method is to manufacture alloys from high-grade ores or from concentrates of leaner ores. A discussion of the costs of ferro-grade manganese ores is pre- sented in chapter 7. This discussion is in general terms only, but should be of use in so far as it relates to competitive conditions.

Jan 1, 1920

By Krogerus. H., P. Jokinen, T. Lintumaa

Keywords: Pyrometallurgy, furnace, coke, smelting charge, optimization, ferrochrome The main consumer of ferrochrome is stainless steel production. Stainless steel must maintain a reasonable price against other competitive materials. Therefore, the ferrochrome price must be low enough and profitable for the producers of stainless steel. The investment and operational costs of ferrochrome production are greatly dependent on the availability of the process and the production rate. Thus the furnace size and production rate in submerged electric arc furnaces will be greatly increased in the near future. The ferrochrome production per furnace, e.g. at Outokumpu?s Tornio Works, increased from 30 000 t/a to 165 000 t/a in about 35 years. The same trend will continue globally but now much more quickly. The Outokumpu ferrochrome process at Tornio Works uses sintered chromite pellets and upgraded lumpy ore as a chromite source. Metallurgical coke is used as a reductant. Reliable smelting in a large furnace demands the correct charge composition and well-known characteristics of the charge components. The quality and electrical conductivity of cokes (normally used) has the most important role for the electrical conductivity of the smelting charge. The results of the measured electrical conductivity of different cokes and the smelting charge with many controlling factors are presented here. These measurements were performed over the years for our own purposes at the laboratory of Outokumpu Research Oy (ORC), in Pori, Finland.

Jan 1, 2006