Search Documents

By A. Deepatana

This study compares the use of an aminophosphonate chelating resin Purolite S950 and a sulphonic acid strong cation exchange resin Purolite C160H to recover nickel and cobalt from the synthetic bioleach solutions. Batch adsorption of metal citrate is performed as a function of metal citrate concentration (15~2000 mg/L) and solution pH (0.01M and 0.1M citric acid). The adsorption mechanism as inferred from the fit to Langmuir (LM), Freundlich (FM) and Redlich-Peterson (RP) models demonstrates that nickel citrate adsorbed onto C160H appears monolayer in comparison to that adsorbed onto S950 exists multilayer. In contrast, cobalt citrate adsorption onto both C160H and S950 agrees with the LM model. The results have shown that loading capacities of nickel and cobalt citrate onto C160H are 60 and 65 mg/g whereas those observed onto S950 are 16mg/g and 6 mg/g respectively. These are achieved in metal citrate prepared in 0.1 M citric acid. Resin regeneration is conducted in using 2 M nitric acid solution. The results show high efficiency of nickel and cobalt citrate elution from Purolite C160H. Findings from this study suggest Purolite C160H is a suitable adsorbent for recovering nickel and cobalt from bioleaching solutions.

Jan 1, 2014

By Luís Marcelo Tavares, Marko Hilden, Malcolm Powell, Grant Ballantyne, Lian Liu

The t10 relationship developed by Narayanan and Whiten has underpinned a number of the JKMRC models and the characterisation of ore competence through impact testing with the drop weight tester. This usefulness is based on a consistent relationship between the t10 value and the overall size distribution that was noted for brittle rocks. However, like all characterisation tests this should be used only when the controlling conditions apply, which in this case is single impact breakage between two metal platens and within the range of sizes in which fragment sizes are normalizable. For any other mode of breakage the relationship should be confirmed before being applied. Soft ores or bimodal ores with widely different competence between dominant components have non-typical breakage signatures. Breakage via single point impact abrasion, compressed-bed breakage, low-energy surface breakage and incremental breakage, to name some of the other breakage modes, do not obey the general t10 relationship, so their outcomes cannot be used to provide a direct comparison. Inappropriate use of the t10 parameter can result in misleading conclusions about efficiency of energy use. These issues and alternative comparison techniques are presented and discussed in terms of choosing appropriate measures of efficiency of breakage, ore competence and energy required for comminution.

Jan 1, 2014

By S. A. Kubyshkin, A. A. Agafonov, A. L. Shakhnin, S. M. Sukharzhevsky, A. A. Komlev, N. V. Vorob’ev-Desyatovskii, A. Pichugina

Cyanidation of gold ore results in formation not only of Na[Au(CN)2], but also cyanometallate complexes of some transition metals. During subsequent gold extraction from such solutions and pulps, using activated carbons (??), a number of problems arise. An effective solution of the problem is not possible without detailed knowledge of the interaction mechanism of transition metals cyanide complexes with AC particles. The chemical properties of AC particles and graphene, saturated with [?u(CN)n](n-1)- (n=2, 3), were studied by XPS, ESR, SQUID, and DFT. The obtained results were compared with the data on AC adsorption of anionic form of Ag(I), Au(I), Cd(II), Hg(II), Cr(III), Fe(II), Fe(III), Co(III), Rh(III), Ni(II), Pd(II), Pt(II) and Pt(IV) cyanide complexes. The adsorption of [?u(CN)n](n-1)- (n=2, 3) on AC from aqueous solutions in air is accompanied with oxidation of ?u(I) atoms. Besides, Cu(II) and Cu(III) compounds were found on AC surface. Quantum-chemical calculations confirmed the possibility of formation of Cu(I) complex with carbene-like sites of AC. The reactions of [?u(CN)n](n-1)- (n=2, 3) complexes and aromatic carbenes and their cation-radical were theoretically studied at DFT PBE level to obtain the information on adsorption of cyanometallate complexes on AC. Carbenes with different fragments were regarded as a model of activated carbons, which have free edge sites with paired o and n electrons. It was shown that [Cu(CN)2]- bounds firmly with triplet carbene, if one Cu-CN bond breaks. The dissociation process occurs through a multi-step spin-crossing mechanism to reduce total spin multiplicity of the metal-carbene complex. The behavior of transition element complexes in contact with AC in aqueous solutions is determined by the following characteristics: geometrical structure of ionic complexes; nature of ligands bonded to the central atom; concentration of reactive oxygen species in solution and its pH; nature of binding sites of AC.

Jan 1, 2018

Hydrofluoric acid (HF) is traditionally used in plant operation to separate feldspars from quartz. It acts during the conditioning step as a pH regulator and an activating agent providing an excellent selectivity. However, a corrosive chemical environment and the ecological impacts from the potential fluoride ion contamination are limiting factors to use this chemical agent at an industrial scale. Investigations of the amine-feldspar interactions in the absence and presence of non-linear long-chain alcohols were carried out on two ore samples. The presence of alcohol molecules led to form a closed packed layer only on the surface of feldspars. The highest order and packing at the feldspar surface were observed with a particular alkyl chain structure as Guerbert alcohols. A new flotation process was developed and tested at both lab and pilot scales on different feldspar ores. The Guerbert alcohols allow to perform a feldspar concentrate with very low content in quartz (2.3-3.5 %) and feldspars recovery from 78 to 81 % while the aliphatic isoalcohols show a more higher recovery level (88-89 %). New HF-free process is strongly dependent on the pH range (1.7-2.5) and sulphuric acid consumption during conditioning steps. Optimal amine/alcohol weight ratio is ranged between 0.8 and 1.0. The values below 0.8 decrease strongly the flotation selectivity and the quartz recovery within the feldspar concentrates is higher than that occurs with HF.

Sep 1, 2012

By G. Y. Liu

The structure-activity relationships for four thionocarbamate collectors are discussed in this pa-per. These collector classes are alkyl alkyl thionocarbamates, allyl alkyl thionocarbamates, acyl al-kyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates. The main emphasis will be to highlight the differences between collectors and their affinities for copper and iron sulfide minerals on the basis of data on electronic-structure properties obtained by vacuum and solution density functional calculations, flotation experiments and analysis measurements. The mechanism of interaction of these collectors with sulfide minerals is also discussed with perturbation theory. The theoretical study results indicate that acyl alkyl thionocarbamates and alkoxylcarbonyl alkyl thionocarbamates have best performance in these agents as flotation collectors with improved collecting power for copper sulfide minerals and excellent selectivity against iron sulfide minerals, which are consistent with the experimental data reported in the literature.

Jan 1, 2014

By M. Saba

In cyanide leaching procedure, achieving an acceptable efficiency for silver and gold is very time-consuming, thus, enough studies have not been performed for optimization and modeling of this process. The kinetics of cyanide leaching includes two steps: first step comprises a sharp slope while the other has a slight increasing trend. In the present study, in order to reduce the time and cost, the cyanide leaching process of a sulfide silver/gold ore was optimized in the first period. The applied parameters and their ranges are: temperature 20-40 (°C); time 1-8 (hrs); cyanide concentration 1-2 (mole cyanide / mole Cu); the percentage of solid to liquid 1-2 (%) and pH 10-12. For design of experiments fractional factorial 2(5-1) was used. Also four center points were applied to increase the accuracy of the model. In addition, by analysis of variance (ANOVA) the most effective parameters were identified and the optimized condition was determined. A regression model was proposed to describe the effects of independent variables and their interacting role on silver recovery. Results showed that the model was linear for silver and nonlinear for gold. In the gold recovery process, the two important parameters are time and pH with the former being more effective. Due to the existence of cyanide ions in the medium, temperature and cyanide concentration have less influence in the gold recovery process. Solid to liquid ratio, in addition, comprises a slight negative impact on the procedure. This emphasizes the different kinetics of silver/ gold cyanide leaching. Finally, using the optimum condition the amount of silver and gold obtained were 61% and 67% in 8 hours, respectively. While in general conditions, the results were 37% and 54% in 24 hours, respectively. Keywords: cyanide leaching, refractory gold/silver ore, modeling, optimization

Sep 1, 2012

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012

Most of the Indian coking coals are medium coking and of very high ash content. Beneficiation of these coals is a must for their utilisation in coke making. During washing while the ash content of the coal is reduced, the same is expected to affect the reactive-inert ratio and the proportion of various petrographic constituents in the clean coal. This will affect the coking behaviour, including the expansion characteristics, of such coal. An increase in expansion behaviour of coal increases the wall pressure and may damage the battery wall. Therefore, close monitoring of coking properties along with drop in ash is necessary for smooth use of the coal in coke ovens. An effort is, therefore, essential to understand the impact of washing on its coking properties. The studies were carried out with captive coals of Tata Steel, India. Three medium coking coal samples namely, VII A, VI A and XI SEB seam coals of West Bokaro Colliery were used for the study. The coal samples after washing to different ash levels were subjected to the following analysis: proximate, crucible swelling number (CSN), LT GK test, dilatometer and plastometer tests and petrography. The experimental data were then analysed to assess the relationship of various coking properties of the coal with its ash content. The studies clearly show that there is a strong impact of beneficiation of the coal on its coking behaviour. The impacts are more at lower level of ash in the clean coal. In general, the coking properties increase with a decrease in ash. This is primarily due to an enrichment of vitrinte materials in the clean coal and an increase in the reactive-inert ratio in the coals. However, the most important impact of the lowering ash is on the increase in the swelling nature of the coal. The coals with lower ash become highly expanding in nature. This may be very critical from operations of coke ovens point of view, especially stamp charged coke ovens. Necessary precaution should be taken in selecting the other coal blend constituents when these coals are beneficiated to a very low level of ash content.

Jan 1, 2014

By A. K. Majumder

In an effort to test the extent to which fundamental fluid mechanics can provide a prediction of particle separation, a study on a simple parallel-sided sluice has been carried out using glass bead and ilmenite mixtures at various particle concentrations and flow rates. Great care was taken to devise a flow splitter at the end of the sluice that permitted accurate measurement of the fluid flow profile and collection of slurry samples, allowing evaluation of the particle species concentration profiles. The actual particle separation taking place was compared to predictions made by first describing the fluid flow by a modified ?law of the wall? model. The hydrostatic pressure variation in the flow was taken into account and the eddy viscosity was calculated from a mixing length expression incorporating Van Driest?s damping function. Using an average density and viscosity provides an explicit expression for the velocity gradient that can be numerically integrated for the flow profile. The particle concentration distributions were then modelled with Hunt?s sediment transport model assuming the particle eddy diffusion coefficient to be the same as that for the water. Hindered settling velocities of the particles were calculated using Brauer and Thiele?s formula, which takes the particle size and density distributions and solids volumetric concentration into account. The resulting predictions of particle separation are shown to be a strong function of the settling velocities of the particles used. Keywords: flowing film concentrators, fluid velocity

Sep 1, 2012

By C. Igathinathane

Coal is the most widely used fossil fuel in the world, providing more than 25% of world?s electrical power. Since, the behavior of coal particles in crushing and grinding circuits, concentration operations, and solid-liquid separations is strongly dependent on size, a reliable and accurate measurement of particle size and particle size distribution (PSD) is a vital aspect in coal cleaning. This paper presents a method for the characterization of ground coal particles using image analysis. We utilized a machine vision (MV) approach that used a document scanner as the imaging device and a user-coded ImageJ plug-in that processed the image and automated the PSD analysis and output results in textual and graphical forms. This approach used a sum of volumes (SVolume) as weighting factor for particle length as the primary dimension of analysis and was successfully applied to ground coal. The plug-in was further improved for computational performance in this study. Mechanical sieving (MS) was also used to compare the MV results. MV results showed that the PSD of ground coal followed a uni-modal normal distribution, and the log-normal plot against particle size exhibited a linear trend for most of the range. MS results, however, had three linear segments, when the width-based sieving results were transformed to lengths by applying the shape factor (width/length), but a definite deviation between the PSD plots was observed. This study demonstrates successful application of the MV SVolume approach for PSD analysis of ground coal, which can be extended to similar particulate minerals and products. Keywords: dimension, fiji, image j, image analysis, coal, particle size, plug-in

Sep 1, 2012

By D. Pirouzan

It is customary to use more than one stage of flotation to obtain an acceptable level of separation of valuables. Flotation circuit design is usually accomplished by applying empirical rules which usually results in operations not working at their optimum conditions. Given the capabilities of genetic algorithms (GA) in finding an optimum solution in a very disturbed search spaces, they can be used to obtain the desired flotation circuit configuration. In flotation circuit configuration and optimization problem, a combination of metallurgical parameters such as yield and concentrate ash content could be used as the fitness function for the genetic algorithm. The multi-objective nature of the problem justified to use Pareto method to arrive at a set of solutions. The appropriate configuration based on technical or economical considerations could then be chosen. To obtain the fitness function for any given configuration, it is necessary to model every flotation stage. The proposed method was used to find the optimum circuit configuration for a coal washing plant. The objective was to arrive at the highest yield while producing a concentrate with a certain ash content (< 11%). The feed to the flotation circuit was characterized based on the size fractions and their flotation rate constants. Results showed that with a 95% confidence, the absolute difference between the modeled and measured values were 2.9-5.5% for yield and 0.4-1.1% for concentrate ash content. When the proposed GA-based circuit configuration was implemented in the plant, the yield increased from the original value of 57.6% to 65.7% while producing concentrate ash content (10.9%) within acceptable limits. By adding one stage to the current three-stage circuit, it was predicted that the yield could further increase by 3.8% while keeping the quality of the concentrate within the appropriate level. Keywords: modeling, optimizing, flotation circuit configuration, genetic algorithms

Sep 1, 2012

By A. N. Zagorodnyaya

The results of research on recovery of ammonium perrhenate from by-products of lead production are presented in the article. For the first time in the world, rhenium marketable products were produced on lead plant of Kazakhstan. Distribution of rhenium in lead production has been studied. During oxidative agglomeration of lead charge, 67.43% rhenium is sublimated and at that, 67.27% rhenium is trapped by the dusts of a system of gas purification, out of them 6.21% is transferred into different solutions, 1.89% into slime and only 0.09% into exhaust. During agglomerate smelting, up to 72% of its rhenium is sublimated and condensed in the dusts also. At leaching stage of sulphate product under dusts processing by the method of sulphatization, 15% of its content in the dusts is transferred into solution. The sorption method on the ionite ?N-21 has been proposed for recovery of rhenium from the solutions of sulphatization. At the same time, rhenium recovery from the dusts into commodity was 13%. The method of direct hydrometallurgy - leaching the dusts by solutions of sulphuric acid under presence of manganous concentrates, has been proposed as alternative method of recovery. This method has allowed increasing recovery of rhenium and other metals from the dusts into solution up to 90%~95%. Rhenium solvent extraction by ??? has been proposed for recovery of rhenium from the leaching solutions. At that, extraction of rhenium into marketable product from the dusts is above 75%.

Jan 1, 2014

By A. V. Neretin

This paper is a continuation and extention of the previous paper on energy-efficient placer mining methods which was presented in 2007 at the World Gold Conference in Cairns, Australia (Nere-tin, 2007a). The paper reports the results only on gravel processing as they were not fully discussed in the previous paper. It is common knowledge that placer gold mining requires processing of large tonnages of gold-bearing gravels by wash plants of different types. In Russia, gold-bearing gravels are mostly disintegrated and screened by the following types of wash plants: a water canon, a derocker or a scrubber trommel. Gold-bearing gravel processing is regarded as highly energy-intensive due to high energy consumption for transportation of large tonnage of material and high pressure water flow rate. The industries requiring a significant expenditure of energy normally estimate the process efficiency by energy consumption per product unit. In order to obtain quantitative data on energy consumption for gravel processing and to estimate placer mining costs, in 2003~2006 four placer gold mines located in the Irkutsk Region were thoroughly investigated through time and motion studies. At all these placer mines gravels were processed by a water canon, a derocker or a scrubber trommel. The objective of the study was to investigate the following parameters: ? wash plant throughput rate per hour; ? hourly diesel fuel and power consumption per cubic meter of gravel processed; ? volume per cent and shape of oversize material; ? different combinations of gravel processing methods. The results from this study were as follows: ? specific energy consumption per cubic metre of gravel processed for different combinations of gravel processing methods was estimated; ? a correlation between energy consumption and unit cost of gravel processing was determined; ? effect of yield and shape of oversize material on wash plant throughput rate per hour was de-fined; ? energy-efficient gravel processing methods were developed. Based on these results, an improved method of gold-bearing gravel processing was proposed. Implementation of this method at a placer mine saved US$ 123 000 in operating expenses only during a short-time Siberian placer mining season. At the same time, this method improved gravel disintegration, screening and processing operations used at the mine. Another advantage of the pro-posed method was higher gold recovery due to reduced yield of undersize material. In order to improve efficiency of gravel processing, a wash system including a derocker for primary gravel processing and a lightweight scrubber trommel was developed. There are two economic benefits of replacing water cannons with the proposed wash system. The first benefit includes lower operating costs for gravel processing due to lower specific energy consumption, while the second benefit is lower gold losses during slurrifying (disintegration and screening) and sluicing of the undersize material.

Jan 1, 2014

By Jie-Liang Wang, Yongdan Cao, Zhao Cao

"The effect of ethylenediamine tetraacetic acid (EDTA) on flotation separation of fluorite from bastnaesite and its selectively depression mechanism on fluorite were studied by single mineral flotation, artificial mixed minerals flotation, solution chemistry analyses, Zeta potential and XPS measurements.The results show that fluorite can be deeply depressed by EDTA while the flotation of bastnaesite is almost unaffected when octanohydroxamic acid (OHA) is used as a collector. The separation index (SI) between bastnaesite and fluorite increases with the dosage of EDTA, SI can be raised from 1.18 to 12.66 when EDTA dosage increases from 0 to 2×10-3mol/L.Solution chemistry analyses show that EDTA is able to convert the Ca(OHA)2 hydrophobic precipitation on fluorite surface to a soluble Ca-EDTA complex but cannot complexly dissolve the Ce(OHA)3 precipitation on bastnaesite surface. Therefore, the Zeta potential of OHA conditioned fluorite can be reduced significantly by EDTA while the reduction degree to Zeta potential of bastnaesite is relatively low. XPS measurement shows that EDTA removes the chemically adsorbed OHA from fluorite surface but has little effect on the adsorbed OHA on bastnaesite surface. As a result, fluorite can be selectively depressed by EDTA in bastnaesite flotation, which behaves an important industrial application prospect in rare earth ore flotation.INTRODUCTIONNowadays, Rare earth elements (shortened as RE) and compounds are of significant importance for a range of rapidly expanding industrial applications including catalysis, metallurgy, renewable energy, and special materials due to their unique electrical, magnetic, optical and chemical properties [1]. The seventeen RE elements, including the lanthanide-group fifteen elements, yttrium and scandium, could be divided into three groups, i.e., light, medium and heavy RE elements based on the different solubility of RE sulfates [2]. Bastnaesite ((Ce,La)CO3), containing approximately 75% REO, is one of the most important light RE minerals [3]. Flotation is the common method to recover basetnaesite [4-6]. Nonetheless, basetnaesite is often associated with calcium-bearing gangue minerals such as fluorite, and the separation of basetnaesite and fluorite by flotation is usually difficult due to their similar surface properties and therefore floatability [7-9]. Therefore, research on high selective flotation reagents of bastnaesite over gangue minerals has attracted a lot of attention [10]."

Jan 1, 2018

By J. Y. Liu

The comminution in a high-pressure roller mill is modeled by an energy-based population balance approach considering three aspects of breakage taking place in the active zones of the mill: the interparticle breakage in the high-compression zone, the breakage at the edges of the rolls, and the pre-breakage in the acceleration zone. Together with an appropriate model of classification, this model can be used to simulate steady-state performance of closed-circuit grindings with high-pressure roller mill. After a brief description of the basic modeling approach, the algorithm of the steady-state calculation for a generalized grinding-classification circuit is presented, from which the circuit configurations commonly met in industrial practice can be derived. With an iron ore as feed material for example, simulation results are shown and discussed in respect of circulating load, specific energy consumption and product fineness for closed-circuit grindings under various operating conditions. The effects of stressing intensity, working gap, classifier parameters as well as circuit configuration on the overall circuit performance are investigated systematically by means of computer simulation.

Jan 1, 2014

By D. R. Nagaraj, Raymond Farinato

Water constitutes one of the most valuable resources employed in mineral recovery and processing. Identifying potential problems encountered in mineral processing in waters unusable for drinking or agriculture (including seawater and even hypersaline waters), understanding chemical factor interactions, and optimization of flotation reagents will greatly expand our ability to create more sustainable beneficiation technologies. The current paucity of our knowledgebase regarding high salinity effects on flotation clearly signals a need for a significant research effort. We report here results of a study designed to probe effects of pulp chemistry on metallurgical performance in the flotation of Cu and Cu-Mo ores in saline waters. The results clearly demonstrate that pH (more correctly dosage of pH modifier to target a pH set point) has the most significant effect on Mo recovery when using seawater. This is linked to the formation/precipitation of Mg(OH)2 when pH = 10.3 (in seawater). The type of pH modifier used, NaOH or Ca(OH)2, had no impact on Cu or Mo recovery, indicating that Ca2+ ions were not involved in any reduction in Mo recovery in the pH range of 9-11. Our results in tap water spiked with either Ca2+ or Mg2+ ions in the same pH range (controlled by NaOH), confirmed that Ca2+ ions had no effect on Cu or Mo recovery, but that addition of Mg2+ ions had a severe adverse effect on Mo recovery at pH = 9.5, and to a lesser extent on Cu recovery. The onset of Mg(OH)2 precipitation occurred at a higher pH, and the adverse impact of Mg(OH)2 on Cu recovery (and perhaps Mo recovery as well) was less, in sea water than in tap water spiked with Mg2+. These effects are attributed to the mitigating role of the high electrolyte concentration, notably NaCl.

Jan 1, 2014

By J. E. Gebhardt, D. McBride, T. N. Croft, M. Cross

"Heap leaching is well-established as a relatively low-cost and low-energy method of extracting metals from low grade ores. However, the design methodology, attention to the engineering details during heap construction and the long time scale in metal recovery makes the process susceptible to significant variation in the success of a heap leach operation. Often the laboratory predicted recovery rates are not achieved on site due to poor understanding of the complex physics of flow and coupled solid-liquid-thermal reactions within the multi-dimensional heterogeneous ore body. Given the large scale of commercial operations, small changes in metal recovery can substantially change the operating profitability. While there are a variety of approaches to heap leach modeling, computational fluid dynamics (CFD) modeling coupled with leach kinetic models offers a methodology to describe and understand the complexities of heap leaching. The CFD model uses leach kinetics specific for the mineralogy of the ore, including gangue chemistry, and provides an energy balance to calculate and predict temperature. Coupled with the CFD model’s inherent capability for modeling complex fluid flow, the physics and the chemistry of the heap can be simulated. This provides a tool for engineering design, as well as forecasting heap production under different scenarios. The calibrated model is used to simulate a three-dimensional test heap under fluctuating meteorological data, such as precipitation events, periodic solution application, and notably temperature. These simulations provide support for a methodology to design and engineer heap leaching of low grade copper sulfide ore. INTRODUCTION Worldwide copper ore reserves are faced with decreasing head grades with copper sulfides, particularly chalcopyrite being the predominant mineralogy (Nesse, 2000). Heap leaching offers an economical way to recover copper from low grade ore. The ore is stacked and a leach solution is applied and allowed to trickle though the porous bed of ore to extract target metals. The heap can be built with run of mine material or crushed ore and is constructed in order to achieve percolation of the leach solution to all regions. Bartlett (1998) provides an authoritative overview of the solution mining process where the leach solution interacts with the solid, the lixiviant dissolves the target minerals from the solid into the solution, and the dissolved species are transported out of the heap for subsequent recovery. Petersen (2016) provides a recent review of heap leach technology and emerging and potential future applications, and Ghorbani et al. (2016) summarizes the current state and challenges of the technology. Early applications of heap leaching offered a low cost technique to achieve high recoveries from oxide ores, typically greater than 70% depending upon the kinetics of reaction. As world copper resources transition to mainly copper sulfide mineralogy, such as chalcopyrite based ores, achieving high recovery from these copper sulfide deposits is proving more difficult due to the complexity of the leach kinetics, which leads to low leaching efficiency."

Jan 1, 2018

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By J. Y. ` Xie

The paper introduced bio-oxidation plants of refractory gold concentrate in China and CCGRI cultures. CCGRI cultures are composed of bacteria and archaea. Archaea Ferroplasma acidiphilum is very thick and fills whole mineral surface. It plays a more dominant role in CCGRI process. Several years of practice has proved that the operating temperature in bioreactors between 38~52?,gold recovery is almost same. Pulp concentration has been increased each year and reached to 25%.

Jan 1, 2014

By Carolina Achiardi, Álvaro Videla

"In pre-design a flotation plant copper sulphide is useful to apply a simplified methodology of economic analysis that relates the size of the grinding product (P80) with the throughput and their effect on copper grade and recovery of copper in the final concentrate of a flotation circuit. With this objective, this methodology covers the following analysis, perform by evaluation of five sizes grinding products (P80): 120, 150, 180, 210 and 240 microns. • Flotation testwork (rougher kinetic, open and closed cycle test) has been done to determinate the optimum operating conditions and to estimate the maximum recovery of copper in the concentrate, using Klimpell model • Flotation plant design assumes a conminution product obtained from a 25,000 HP ball mill • Metallurgical balance is performed for the circuit based on flotation testwork • Economic evaluation by calculating capital expenditure (CAPEX), operating expenditure (OPEX) and sales revenue, to determine NPV is performed and relates to the NPV. An optimum grind size is then obtained based on cash flow. The results shows a grinding product size that optimizes flotation and allows a higher NPV and INPV over other alternatives."

Jan 1, 2014