Search Documents

By J Pan, Q H. Li, D Q. Zhu, C C. Yang, X Wang, Z Q. Guo

Al2O3 in natural iron ores generally occurs in goethite, kaolinite, gibbsite, hematite and iron carbonate. When the content of alumina in sinter increases from 1.11 per cent to 3.50 per cent, the reducibility of sinter decreases with the addition of four different types of alumina. When gibbsite and kaolinite are added, the low temperature reduction disintegration (RDI+3.15 mm) of sinter increases with the increase of Al2O3 content in the range of 1.5 per cent to 3.5 per cent. Furthermore, when adding pure reagent alumina, the increase of Al2O3 content in the range of 1.5 per cent to 3.0 per cent will increase the RDI+3.15 mm of sinter. The addition of ferric oxide–alumina spinel with the Al2O3 content in the range of 1.5 per cent to 2.5 per cent, also increases the RDI+ 3.15 mm of sinter. The influence difference is results from the change of the mineral composition and microstructure of sinter because of the occurrence state of Al2O3. Under the condition that Al2O3 content of sinter is 2 per cent, the porosity of sinter with kaolinite is 37.26 per cent, and the shape is irregular. When gibbsite and ferric oxide–alumina spinel are added, the porosity of sinter is about 16 per cent, and the pores are round. When pure reagent alumina is added, the porosity of sinter is 17.49 per cent, and the pores are regular and small. When kaolinite, gibbsite and ferric oxide–alumina spinel are added, platy calcium ferrite is mainly formed in the sinter, and some of it is columnar calcium ferrite. On the other hand, when pure reagent alumina is added, in addition to platy columnar calcium ferrite, acicular calcium ferrite is also formed in the sinter.

Nov 8, 2021

At its Port Kembla Plant, Australian Fertilizers Ltd. manufactures Superphosphate and other Phosphatic Fertilizers.Phosphate Rock is received from Nauru and Ocean Island. It contains water insoluble tri-calcium phosphate, Ca3(PO4), to an average of about 86%.It is crushed to pass a 20-mesh x 26-gauge woven wire screen, and is then treated with Sulphuric Acid to give the product Superphosphate with a water solubie prosphate content of 20.5%, estimated as P205. Sulphuric Acid is made by the chamber process. Three sets of chambers are installed, on,e five-chamber set of timber frame work construction and the other two of more recent date, each with four chambers of steel frame work construction. A fourth chamber set is now being built.Sulphuric Acid is delivered for use. at about 70% H2S04, the strength depending upon the rock used.Mixing - The crushed rock and sulphuric acid are mixed in weighed and measured proportions respectiyely in one-ton batches in revolving cast fron pans, mechanically stirred. The mixture, while still slurry, is run into a closed horizontal concrete cylinder (den) where, with the completion of the chemical reaction, it rapidly sets as Superphosphate.Approximately fifty batches are required to fill a den. When full, the den is opened ana the mass cut out by a revolving cutter. The product is elevated and conveyed to any required position in the Superphosphate storage shed, where it dries and matures.Despatch - As required, the Superphosphate is excavated by a two ton grab and conveyed from the matured "dump" to bagging units where it is disintegrated, screened and bagged at twelve bags to the ton. The filled !Jags are closed by machine and delivered to railway trucks immediately.Mixed Fertilizers - Sulphate of Ammonia, Sulphate and Muriate, of Potash, and Blood and Bone are mixed with Superphosphate and thoroughly incorporated to give different mixtures to meet special plant requirements.

Jan 1, 1938

By J Pan, C M. Tang, D Q. Zhu, C C. Yang, S W. Li, Z Q. Guo

The short process of electric furnace steelmaking with direct reduction iron (DRI) as raw material is an important process for smelting high-quality and special steels. In order to prepare high-quality DRI, the pellets with basicity of natural basicity and 0.4 were prepared from magnetite concentrate (MR=0.09, MR=0.4) and hematite concentrate (HR=0.02, HR=0.4). Based on the HYL method, the gas-based direct reduction experiments were conducted under the condition of rich hydrogen (H2/CO = 2.6). The reduction index (RI), reduction swelling (RSI), cold compressive strength (CCS), and phase changes of the pellets were systematically studied. The results show that the RI of four kinds of pellets is greater than four in the temperature range of 800~950°C. For the magnetite pellets, at a fixed reduction temperature, the RSI increases and then gradually decreases, reaching a peak between 50 per cent and 80 per cent. Moreover, the RSI enhances with the increase of the reduction temperature. In general, the RI, RSI, and reduced CCS of the MR=0.09 pellets are better than those of the MR=0.4 pellets. For the hematite pellets, the maximum RSI decreases from 23 per cent to 17 per cent during hydrogen-rich reduction, while the compressive strength increases from 500 to 1070 Nꞏpellet-1. The main reason is that the glass phase generated by the increase of basicity adheres to the surface of hematite grains, hindering the contact between reducing gas and particles. As a result, the apparent activation energy is reduced, which is not conducive to the reduction process. In addition, the glassy phase attached to the hematite reduces the migration rate of Fe2+/Fe3+, resulting in a difference in the reduction expansion rate of hematite in the inner and outer layers of the pellet. Thus, concentric cracks are formed inside the pellets, the RSI increases and reduced CCS decreases.

Sep 18, 2023

By A Rantala, C Cruickshank, I Muzinda, O Haavisto, J Timperi

The production at First Quantum Minerals’ (FQM) Kevitsa Mine, located in northern Finland, commenced during the second quarter of 2012. Presently, the mine processes approximately five and half million tonnes of ore annually, producing nickel, copper and platinum group metal (PGM) concentrates. In order to support fast production ramp-up and optimise the performance of flotation thereafter, an extensive advanced flotation control solution was implemented by Outotec in collaboration with FQM Kevitsa.In addition to basic process instrumentation and process control, each of the 14 Outotec 300 m3 and another 26 cells, ranging from 20–160 m3, have been equipped with state-of-the-art systems providing froth image analysis and automatic froth speed control. Also, the flotation cell levels are stabilised with advanced feed-forward level control.The online analyser provides key feedback information of the process performance for the advanced process control (APC) system. Based on this information, APC system defines grades and recoveries according to rules defined by Kevitsa process metallurgists. This system executes the control strategies for optimising the production of concentrates.Throughout the implementation and support phases, specific and intensive attention was paid to ensure plant personnel gained full understanding of interacting with the system and how to incorporate their process experience and skills to optimise the APC strategy. This level of expertise is also a valuable asset in understanding the APC system’s contribution to the overall performance of the plant as well as providing the ability and confidence to define key performance indicators used for continuous assessment. The experiences and results from site achieved so far are discussed in this paper.CITATION:Rantala, A, Muzinda, I, Timperi, J, Cruickshank, C and Haavisto, O, 2014. Implementation of advanced flotation control at First Quantum Minerals’ Kevitsa mine, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 369–378 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D P. Blair

Various analysis techniques are used to determine the nature of a large seismic event that was triggered by a mass blast in an underground mine. This event was recorded by surface accelerometer arrays whose output was doubly integrated using a stable filter to determine the dynamic displacements. The peak dynamic displacements during the blast were 0.09 mm, and during its latter stages, this blast induced a seismic event having a peak dynamic displacement more than ten times larger at 1.26 mm. Polarisation analysis, based on the complex covariance matrix, showed that the seismic event was caused by movement of a known underground fault, close to the blast, which radiated most of its release motion as a shear-horizontal (SH) wave. The change in frequency content with time for the blast and seismic event was initially determined using the Fourier-based reassigned S-method. This analysis showed that the large amplitude seismic event had frequency content significantly lower than that of the blast. Nevertheless, this Fourier technique still retains the problems associated with short time windows as well as the fact that most realistic signals are non-stationary. In order to eliminate such influences, the more recently developed empirical mode decomposition (EMD) was used to obtain the intrinsic mode functions (IMF) of the seismic wave propagation. The EMD vibration analysis showed that each IMF generally exhibited distinct frequency changes throughout the blast and a significant reduction in frequency throughout the subsequent event. It is shown that most of the energy of the seismic event is contained in IMF modes 2, 3 and 4 of the SH wave; the high-frequency first mode (IMF1) contains little energy. Such modal analysis is not possible using standard Fourier methods.CITATION:Blair, D P, 2015. Dynamic displacements from a blast-triggered seismic event, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

The æMountain Camp reefÆ at Alford's mine, Wakamarina,Marlborough, had no recorded gold production although assays of 5 - 26 g/t were reported, but it did produce c. l000 kg of scheelite. The lode consists of a lower massive quartz layer, and upper, cm-banded, ribboned quartz layers, and has a very low sulphide content. Within the massive layer, relict early fine-grained mosaic quartz with idioblastic scheelite is surrounded by recrystallised granoblastic coarse-grained quartz with calcite and plagioclase, in which an original ribbon banding texture is mimiced by strings of tiny inclusions. In both the banded and massive layers, rounded quartz grains, created by cataclastic milling of grain margins and along syn-vein fractures, have been partially annealed within later quartz overgrowths. Late fibrous quartz and calcite fill brittle cross fractures.   Deformation events D1 and D2 are associated with mid-late Jurassic metamorphism of the Pelorus Group, D2 producing the main regional schistosity (S2, and the earliest scheelite. D3 is an extensional mylonitic shear event that formed the dominant schistosity in Alford's mine (S3). The quartz lode was emplaced within the mylonite by a series of individual dilation pulses (D4). The D5 event caused crenulation of the S3 mylonite, kink banding and chevron folding of the S2 schist and S3 mylonite, and reverse faulting, rodding and cross-fracturing with late fibrous quartz-calcite veining of the D4 quartz lode.   Fluid influxes during successive dilations of D4 fractures progressively caused recrystallisation of earlier quartz bands on the footwall, annealing and recrystallisation of quartz along milled crystal margins and fractures, and deposition of minor sulphides. There was thus a dynamic interplay between fault dilation, lode fracture, fluid influx, lode band deposition, and lode recrystallisation. Illite-Kfeldspar al ¦ 2 Ma (K/Ar), c.30 Ma after metamorphism.

Jan 1, 1996

By Ho SE, Neil Phillips G, Houstoun SM

There are numerous individual gold deposits in the Archaean greenstone belts of Western Australia, but only 26 have productions and/or quoted reserves in excess of 10 tonnes Au. Most gold production has come from mineralization in shear zones, quartz veins or stockworks in volcanic or intrusive host rocks, particularly tholeiitic basalts or dolerites metamorphosed at sub-amphibolite facies (e.g. Kalgoorlie). Significant prod- uction has also come from BIF-hosted deposits (e.g. Hill 50), and large reserves are quoted for mafic hosts at high metamorphic grade (e.g. Big Bell). Most deposits have marked structural control, great depth extension, and are characterized by zoned alteration haloes of pyritization (with Au), K-metasomatism and carbonation. On the regional scale, most larger volcanic- or intrusive-hosted deposits occur in younger (ca 2.8 b.y.) rift-phase green- stones (Norseman-Wiluna Belt). These belts also have a high prospectivity (36 kg Au/km2 of greenstone belt). Younger (ca 3.0 b.y.) and older (ca 3.5 b.y.) platform-phase green stones of the Murchison and Sodthern Cross Provinces and the east Pilbara, respectively, are progressively less prospective (14 kg Au/km2 and 0.8 kg Au/km2, respectively) and also have progressively smaller deposits. The important regional- and local-scale characteristics of most gold deposits can be explained in terms of a metamorphic- replacement model. In this model, metamorphic H2O-CO2 fluids, focussed by faults and shear zones, infiltrated host rocks and deposit gold at 350 + 50¦C and 1-2 kb, largely in response to fluid-wallrock interaction. In many large deposits, gold precipitation was synchronous with sulphidation of Fe-rich host rocks, but the diversity and abundance of smaller deposits reflects the variety of reactions precipitating gold from ubiquitous, auriferous metamorphic fluids. Regional variations in abundance and size of deposits relate to factors such as tectonic setting, alteration styles and possibly source rocks.

Jan 1, 1986

By L Jackson, A Parbhakar-Fox, N Fox

"Characterisation of sulfide minerals (eg pyrite, sphalerite) in historic tailings can assist in determining whether there are economic benefits of reprocessing such materials using modern metallurgical practices. In addition, there are associated environmental advantages if the historic tailings are actively generating acid and metalliferous drainage (AMD). At the Old Tailings Dam (OTD), Savage River, Western Tasmania, 38 Mt of pyritic tailings were deposited from 1967 to 1982; consequently it has been recognised as an AMD source. Long-term management options considered for this site have included the establishment of either a water, hard-engineered or vegetation cover. However, due to geotechnical challenges posed and the lack of success demonstrated by previous pilot studies, these strategies have not been implemented. Instead, resolving the pyrite chemistry can allow for a first-pass assessment of whether reprocessing these tailings is a feasible option as part of a long-term management strategy for this legacy site.Tailings samples (n = 144) were collected across the OTD from up to 2 m depth from five facies (A–E), and four zones (1 to 4; defined by hydrological regime and grain size). These materials were subjected to acid-base accounting (ABA) and mineralogical evaluations to determine their geoenvironmental characteristics. Following this, 26 samples were selected for in-depth laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) investigations to evaluate pyrite chemistry across different tailings facies. The results revealed enrichment of Co and Ni in these materials. Specifically, Co content was up to 3.0 wt per cent, particularly within facies C to E, and Zones 3 and 4. Cobalt is recognised as a critical metal, therefore, reprocessing should be considered as a future rehabilitation option for the OTD, pending resource definition using established codes and practices.CITATION:Parbhakar-Fox, A, Fox, N and Jackson, L, 2016. Geometallurgical Evaluations of Mine Waste – an Example from the Old Tailings Dam, Savage River, Tasmania, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 193–204 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S J. Chen, N Jiang, Y S. Ding, F X. Li, D W. Yin, F Wang

This study assessed the deformation failure characteristics of rock-coal composites with different height ratios. Uniaxial compression tests were conducted using an acoustic emission monitoring system and XTDIC three-dimensional full-field strain measurement system. The results showed that with the increase in rock-coal height ratios, the uniaxial compressive strength of composite samples increased from 5.26 MPa to 14.61 MPa. The evolution of the deformation localisation zone of the composite samples is closely related to the initiation and propagation of the primary cracks in the coal samples. At the moment when the main fracture of the coal samples occurs, there is a large drop after the peak of the stress-strain curve of the composite samples, and the height of the rock samples increased to varying degrees, which indicated that the failure of the coal samples induced the rebound deformation of the rock samples. With the increase in rock-coal height ratios, the rebound deformation amount of the rock samples decreased from 0.042 mm to 0.008 mm, and the rebound deformation rate decreased from 0.210 per cent to 0.010 per cent. Meanwhile, the rock samples’ rebound deformation releases part of the elastic energy to act on the coal sample, further contributing to the destruction of the coal samples. Compared with single composite coal samples, the coal samples of the composite samples have much more failures. In addition, with the increase in rock-coal height ratio, the input energy density, elastic energy density, post-peak release energy density, and residual elastic energy density of the composite samples increased, the dissipation energy density decreased, and the percentage of pre-peak elastic energy density increased from 98.56 per cent to 99.86 per cent. These results revealed the deformation failure characteristics of rock-coal composite with different height ratios and provided a theoretical reference for understanding the underground dynamic rock failures.

Nov 29, 2022

Xstrata CopperÆs Mount Isa Copper Operations is located in mineral rich north-west Queensland and is one of the largest sources of copper in the world. This world-class underground operation is planned to produce over 6.6 million tonnes of copper ore in 2007 from the X41 and Enterprise Mines. With an underground mining history of over 50 years and underground reserves of over 83 million tonnes at 2.6 per cent copper, mine planning for the future becomes an exciting challenge for the technical team due to the older nature of certain areas. The 1100 Orebody of the X41 mine was one of the first places that copper mining occurred, with its discovery in 1953 - 1954 and mining commencing in the 1960s. Sublevel open stoping mining methods have been employed since that time as the means of extraction, using a primary-secondary sequence to maximise stope turnaround time. Large Transverse Pillars within the 1100 orebody were not mined out in order to provide access for ventilation, power, orepasses and other services. The Panel Pillar, 4180XC and 4010XC pillars are three such Transverse Pillars in the 1100 orebody that will be mined as a final retreat. This paper discusses the technical challenges and issues associated with the extraction of Q390 stope, one of the stopes located in the Panel Pillar, and the design solutions to overcome these issues. Managing the exposure of backfilled stopes of variable fill strength, ensuring the stability of the crown, stope walls and drawpoints, managing vertical openings, re-establishing service networks, and stope filling are the critical issues given consideration for the final design of Q390 stope and other such stopes within a Transverse Pillar. Communication and coordination between the different departments in the mine are essential for the necessary work to be completed in a timely manner to bring pillar stopes into production.

Jan 1, 2007

By L N. Loganathan

Risk exposure in tunnel projects is extremely high due to various factors such as variability of subsurface conditions, selection of inappropriate design and tunnelling methods, improper risk assessment on adjacent surface and subsurface structures and utilities, and inadequate contractual practices. The risks in tunnelling must be borne by the contractor, designer and the owner of a tunnelling project. There have been a number of improvements in the last ten to 15 years in the manner in which tunnel projects are developed and implemented in terms of their design, construction, financing and operations. One significant improvement has been the manner in which underground conditions and their risks are being managed. Owners are less willing to transfer the full responsibility to the contractor for managing the underground conditions, although this is a familiar manner in which underground major urban projects have been previously contracted and managed. The owners of tunnel projects in Singapore have advanced the risk management process for their projects through geotechnical interpretative baseline reports (GIBRs), geotechnical data reports (GDRs) and project specifications (PSs). This paper discusses industry practice and its development as well as the application during the preparation and use in Singapore on the Deep Tunnel Sewerage System (DTSS) and the Marina Coastal Expressway (MCE) project in Singapore. The DTSS trunk sewer is 48 km and ranges from 3.3 m to 6 m finished diameter up to 50 m below the ground. The underground conditions ranged from Old Alluvium, strengths of about 1 MPa to competent Bukit Tima granite, with strengths of over 230 MPa. The total route length of the MCE is about 5 km. About 3.6 km will be constructed underground, consisting of dual five-lane carriageways. The underground construction will be cut-and-cover, and 2.6 km will be constructed about 13 m underground, and 1 km of tunnel will range from 13 m to 24 m as the tunnel passes under a 420 m wide reach of Marina Bay, whose crossing will be constructed as a two-phase cofferdam.

Jan 1, 2008

By M BSckstr÷m

Acid rock drainage (ARD), commonly found in vicinities of sulfidic mines, possess properties capable of widely affecting the surrounding environment by acidification and heavy metal pollution. In most ARD treatments, various alkaline sources are used to neutralise the acid produced. Utilisation of highly alkaline fly ashes instead of raw materials is a cost-effective alternative, which lately have become increasingly popular. In laboratory batch experiments, neutralising capacity of fly ash was studied during 20 days. ARD was added to the fly ash once a day, for each increment the liquid to solid ratio (L/S ratio) was increased. At an early stage of the experiment (day 6, L/S ratio 12), the concentration of barium in solution unexpectedly increased by a factor of 50 (from 200 to 10 000 ¦g+l-1). This high concentration also sustained the following two days (L/S ratios 14 and 16) before dropping to the original level. pH showed a slight increase during these observations (pH 12.4 - 12.7). The phenomenon was also observed in a parallel and identical series. In addition to barium, aluminium and strontium clearly increased in the same manner, however not as much as barium. Furthermore, concentrations of chromium and molybdenum noticeably decreased at these distinct L/S ratios (12, 14 and 16). The behaviour of barium and subsequently strontium, aluminium, chromium and molybdenum is only partially understood. The decrease of chromium and molybdenum is suggested to be due to incorporation into the interlayer regions of hydrocalumite (Ca4Al2(OH)12(OH)2+6H2O), replacing the hydroxide groups, which also explains the increase in pH. Moreover, the increase of barium, strontium and aluminium could be attributable to dissolution of the silicate mineral celsian (Ba,Sr(Al2Si2O8)). Alternatively, barium and strontium increase could be explained by dissolution of a Ba,Sr(SO4)-solid solution and aluminium increase by dissolution of hydrocalumite or ettringite.

Jan 1, 2008

By X Zheng, P Manton

Pebble recycle crushing circuit performance at Telfer has historically fallen significantly short of the design product P80 of 12 mm. An investigation was undertaken to evaluate the current pebble crusher circuit performance, quantify the optimum performance achievable with the existing circuit and examine the impact of pebble crusher performance on the overall grinding circuit throughput. The primary objective of this investigation was to develop an operating strategy that could consistently deliver the finest possible pebble crusher product to maximise the overall plant throughput.The pebble crusher specific energy (Wc) was proposed as a key control variable for pebble crusher operation based on the results of plant survey work. Over the range of pebble crusher specific energies encountered at Telfer, a strong linear relationship was found to exist between Wc and the crusher product size. This direct linear relationship between specific energy and crusher product size remained constant regardless of how the change in specific energy was generated, ie through changes to the crusher closed side setting (CSS), feed rate, liner profile or moisture content. Key findings for the Telfer pebble crushing circuit were: each 0.1 kWh/t change in Wc resulted in a 4.9 per cent to 6.0 per cent change in plant throughput, each 1 mm change in pebble crusher CSS resulted in a 2.2 per cent to 2.6 per cent change in plant throughput, and 0.57 tonne of new feed was displaced for each tonne of crushed pebbles recycled to the semi-autogenous grinding (SAG) mill. The presence of an existing 3000 tonne pebble stockpile between the SAG mill and pebble crushers provides an opportunity to manipulate the feed rate to the pebble crushers independently of the SAG mill pebble production rate. This flexibility, along with excess pebble crushing capacity, enables the pebble crusher specific energy to be maximised the majority of the time. Pebble crusher specific energy has subsequently been incorporated as an online crusher control measure to assist in maximising plant throughput.

Jan 1, 2009

Alluvial mining even of shallow deposits is often economically a marginal proposition and causes significant disruption of the land surface through the need for large scale excavation. In-situ leaching using chlorine-based solutions eliminates the need for excavation, the disruption of surface activities, and may greatly reduce processing costs and improve recovery especially of fine gold. A spreadsheet model has been developed to design and analyse the economics of in-situ leaching of alluvial deposits. In-situ leaching of shallow deposits may be achieved in a number of ways including solution infiltration via perimeter ditches or the use of injection and production wells. In most instances deeper alluvials may only be processed using well systems. Two deposits are analysed in this paper. The first consists of one metre of payable wash beneath one metre of overburden. Some thirty fields per year are treated processing 450 000 BCM per year at a cut-off grade of around $4/tonne ($8/rn3 or the gold value equivalent of 0.26 gh or 0.52 g/m3). The principal costs are well drilling and labour. Sensitivity analysis indicates that doubling the throughput halves the cost. The economics of the project are relatively insensitive to reagent costs and consumptions, and halving the recovery doubles the cut-off grade. Shallow deposits treated using the infiltration ditch system may be marginally cheaper and more conveniently managed although this depends on the relative cost of digging the perimeter ditches. In a second example, deep leads with one metre of wash beneath 30 metres of overburden necessitate significant drilling and feature reduced throughputs as a consequence. In the example chosen 30 fields a year are processed for an annual throughput of 65 000 tonnes costed at around $20/tonne (1.4 g/t Au equivalent, $40 /m3). Sensitivity analysis indicates that throughput, and drilling cost per metre are not important but there is a high sensitivity to recovery and to the depth to payable wash.

Jan 1, 1992

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005

The Myra Falls minesite, of Westmin Resources Limited, is located at the geographic centre of Vancouver Island, within the confines of Strathcona Provincial Park. The operation includes two active underground mines, II-W and Lynx, together with a modem 3650 1/d milling facility. Recent exploration successes will lead to the commissioning of a third mining area in late-1993 - The Battle/Gap Mine. These ore deposits are complexly metal-zoned volcanogenic massive sulphides of Devonian age, hosted in the Myra Formation of the Sicker Group volcanic assemblage. Three distinct felsic volcanic units are defined within the 450 metre thick Myra Formation. They are, from oldest to youngest, the H-W Horizon, the LMP Horizon and the Upper Rhyolite Unit. Massive sulphide mineralisation occurs throughout the property in the H-W and LMP Horizons. There are a number of orebody types, including polymetallic massive sulphides, polymetallic disseminated sulphides, zoned pyritic massive sulphides, elastic sulphide zones and stringer sulphide zones. Individual orebodies range in size from 10 000 tonne zinc-rich polymetallic lenses to the ten million tonne, zoned massive sulphide H-W main lens. The property has been in continuous operation for 26 years, producing over 13 Mt of ore averaging 2.2 g/t Au, 64.0 g/t Ag, 1.9 per cent Cu, 0.6 per cent Pb, and 5.6 per cent Zn. Current geological reserves stand at 12.5 Mt at a comparable grade, including 4 Mt of recently discovered high grade ore in the Battle and Gap Zones. Mining and milling methods have evolved over time to enable successful extraction and milling of these complex ores. Change is on-going with the recent conversion of the H-W Mine to large-scale bulk mining methods, and the development of effective computerised ore reserve calculation and mine planning tools. These changes, in concert with successful exploration techniques that led to recent high grade ore discoveries, have breathed new life into the operation and should assure its present and future viability.

Jan 1, 1993

By M Hernan

Bendigo Mining Limited has established a modern underground gold mine and processing plant at Bendigo in central Victoria. The Bendigo goldfield produced around 22 000 000 oz of gold between 1851 and 1954. Approximately 4 000 000 oz were sourced from surface alluvial workings with the remaining 18 000 000 oz won from underground quartz reefs. The modern mine is accessed via the Swan Decline, which commences at the Kangaroo Flat site on the southern outskirts of Bendigo and progresses in a north easterly direction between the Deborah and Sheepshead anticlines, reaching a depth of almost 1000 m below the City of Bendigo. Development of this decline commenced in 1998. Since that time 20 km of underground development has been completed. Exploration drilling, on-reef development and bulk sampling carried out between 1999 and 2005 resulted in the estimation of a Probable Ore Reserve of 700 000 tonnes at 9.0 g/t gold for 207 000 oz of gold. These Ore Reserves were contained within four reefs located on the Deborah and Sheepshead anticlines. Reef mining commenced in late 2005 from the Shywolup and Greater Garrard reefs. Material mined was stockpiled on the surface in preparation for commissioning of the process plant which commenced in mid 2006. Mining and processing were carried out between August 2006 and May 2007 during which time 176 000 tonnes were processed at an average grade of 5.4 g/t gold to produce 26 735 oz of gold. Plant feed was sourced from four reefs. This paper discusses some of the issues which were encountered with the definition and mining of these geologically variable and nuggetty reefs. This paper covers exploration techniques, grade estimation, mine geological control, mining methods, geotechnical issues and reconciliations. It will also discuss some of the lessons learnt and how these will be applied to future Mineral Resource and Ore Reserve estimation, as well as underground operations.

Jan 1, 2008

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G Lumley

Gold miners have been underperforming the price of gold for a number of years. So why has the æmarketÆ undervalued our gold miners relative to what they have been mining? The low valuation ascribed to gold mining companies is largely attributable to their profit performance. In the period since 2006 the price of gold in A$ has risen about $900/oz, but the real cash margin (operating cash costs + cost of finding and/or acquiring deposits + the cost of bringing them into production) has only risen about A$100. Rising operating costs are a major part of this reduction in real margin. Energy and labour costs have risen more than the inflation rates across a number of countries as have taxes, royalties, etc. There are however, more significant contributors to the rising cost base. Firstly, in 2006 the average gold grade was 2.0 g/t; today it is 1.3 g/t. Secondly, strip ratios (for surface mines) have increased by 19 per cent during this time. Open cut mining equipment unit output across the world has dropped by 26 per cent during 2006 - 2012. Finally, costs have risen by 55 per cent during this time period. Consequently, there is now 3.8 times more mining cost required to produce an ounce of gold from surface mines compared with 2006. The decline in gold grade looks to be a permanent trend as does increasing strip ratio if output is to be maintained. Costs will continue to rise although cost control will be necessary. Reversing the decline in equipment performance and closing the gap between median and best practice provides the hope for a sustainable reversal of cost increases. The current gap between best practice and median performance has grown to 112 per cent for mining trucks, 168 per cent for excavators and 169 per cent for front end loaders. Closing this gap is the potential for a more profitable future. For most gold mining companies improving mining efficiency is not an option; it is an imperative.CITATION:Lumley, G, 2013. How many gold mines will inefficiency kill?, in Proceedings World Gold 2013 , pp 267-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

THE North Mount Lyell Mine is situated on the southern side of Mount Lyell at an altitude of 1750 ft. above sea-level. The average rainfall is 117 in., and there are generally several light falls of snow during the year. Despite the heavy rainfall, which is fairly evenly distributed over each of the twelve months, the climate is equable and not unduly rigorous, and, provided that the mine employee is suitably clad, it is only on exceptional days that he experiences any discomfort by becoming wet journeying to and from the mine.The majority of employes reside at Queenstown, and are conveyed by special trains to and from the top of the haulage, which is less than a mile from the mine. The mean surface temperature at the mine is 46° F., with a maximum variation from 26° F. to 85° F., the relative humidity generally being higher than in other districts. The rock temperature is 48° F. on the 200-ft. or Main Adit level, and 54° F, on the 1200-ft. level, giving a rise of 6° F. for 1000 ft. in depth.The ventilation of the mine is natural, the downcast being served by the Crown and Blocks shafts and the Crown mullock pass, and the upcast air is carried away from the workings by the Main shaft and the Nos. 1 and 2 mullock passes. The quantity of air circulating varies from 25,000 cub. ft. to 35,000 cub. ft. per minute, the greater quantity moving in the colder weather. The downcast air in traversing the wet shafts becomes saturated and enters the level at the rock temperature of 54° F. in winter and about 56° F. in summer, while temperature readings of the outcast air indicate that it varies very little.In the southern end of the mine the Blocks shaft downcast air upcasts through the different stopes, and their mullock passes, to the level above for each level to the 700-ft. level, where it passes to one of the main uptakes. The prown shaft downcast air supplies...

Jan 1, 1927