Search Documents

By Claudio Asioli

"The project’s goal was to construct the Al Ghazala Intercontinental, a multi-use development in the bay area of Tripoli overlooking the Mediterranean Sea. The site of the project is located approximately 500 ft (150 m) from the Mediterranean coast, near the Al Ghazala roundabout in the town center of Tripoli, Libya. The investor of the project was Magna Properties Group, Ltd. – Libya, the main contractor was Man Enterprise S.A.L., and the design and construction management was performed by Dar Al-Handasah Engineering. Trevi S.p.A. was contracted to perform the design and construction of the anchored diaphragm walls and dewatering systems for the excavation of a two-level basement car park, which extends across the full footprint of the site.The site was approximately 640 ft by 230 ft (195 m by 70 m) in plan and nearly flat. The groundwater level typically varies from about 11 ft to 23 ft (3.4 m to 7.0 m) above mean sea level. To construct the required raft foundation, it was necessary to excavate the area down to El. -15.7 ft to -26.3 ft (-4.8 m to -8.0 m), which resulted in an excavation depth ranging from about 27 ft to 39 ft (8.3 m to 12.0 m) below the existing ground surface. Subsurface ConditionsThe subsurface site investigation was performed in three phases by Al-Tamier Engineering Consulting Bureau. During Phase 1, a preliminary investigation was undertaken during the early stages of the project to obtain information about the general stratigraphy and groundwater level at the site. Phase 2 was performed to obtain subsurface information and design parameters, and Phase 3 was performed as a supplementary ground investigation to investigate unexpected ground conditions identified during Phase 2. In total, 14 boreholes were drilled to depths ranging from about 80 ft to 180 ft (24 to 55 m). The generalized subsurface profile is quite heterogeneous, and is predominantly composed of sand with silt and gravel that is underlain by limestone, calcarenite and claystone."

Jan 1, 2017

By L. W. Hamel

"DUST CONTROL - GRANISLE COPPER LIMITEDINTRODUCTIONGranisle. Copper Limited is located in the north-central region of the Province of British Columbia, approximately 200 road miles north-west of Prince George. Mill startup was in November, 1966, at a rate of 5,000 tons per day, expanded to 13,000 in 1973. The primary crushing rate is 1,200 tons per operating hour, and the secondary 750, and they can be operated jointly or separately.DUST COLLECTION SYSTEMS There are seven dust collection systems ventilating the crushing and grinding complex. The individual pickup points are depicted on Figure 1 -""Crushing Plant Flowsheet"", and Figure 2 - ""Concentrator Flowsheet"", e.g. 1A, 1B, 3C, etc.System No. 1 - Primary Crusher The feed rock box of the Allis-Chalmers superior 42-65 primary crusher is ventilated by 19,000 CFM of air exhausted directly to atmosphere by a Sturtevant 426 M fixed discharge fan.No. Dust Pick Up Point CFM lA Crusher Feed Rock Box 19,000System No. 2 - Primary Crushing and Screening System No. 2 ventilates the primary crushing and screening equipment. A total of 19,000 CFM of air is exhausted by a Sturtevant 426 M fixed discharge fan through a Howden Type S - size 75 cyclone locally modified for wet scrubbing."

Jan 1, 1976

By Edward S. Plotkin, Joseph D. Guertin

In a continuing effort to upgrade tunnel design and construction practice, the New York City Transit Authority sponsored a geotechnical monitoring program on a recently completed section of the E. 63rd Street line in mid-town Manhattan. The purpose of the program was to document rock behavior as well as temporary and final rock support systems to provide a possible basis for either confirmation or modificification to design methods and construction specifications. This paper describes those portions of the study associated with rock behavior and temporary support systems. The entire study included monitoring of rock movements above the tunnel as well as adjacent to a 36.6m (120 ft) shaft, monitoring of stresses in steel ribs, monitoring of loads in rock bolts in two test sections and monitoring of stresses in the final concrete lining. PROJECT DESCRIPTION Route 131-A, Section 4 is located in mid-town Manhattan extending from under the Central-Park Zoo on Fifth Avenue eastward under 63rd Street to the end of contract between Madison and Park Avenue. Figure 1 is a Project Locus Map. The contract included approximately 355m (1165 l.f.) of 4 track tunnel(13.4m (44 ft) wide by 13.7m (45 ft) high excavated dimensions) plus a 22.9m (75 ft) by 19.8m (65 ft) by 36.6m (120 ft) deep ventilation shaft. The entire tunnel and most of the excavation shaft was excavated in metamorphic rock, known locally as the Manhattan Schist. The depth to tunnel invert varied from approximately 27.4m (90 ft) at the west end of the contract to 35.Om (115 ft) at the east end. Rock cover above the excavated crown varied from approximately 6.7m (22 ft) at the approximate mid-point of the contract to 18.9m (62 ft) at the western end. A plan view and interpreted geologic profile are illus-

Jan 1, 1979

By W. R. Reed, J. P. Rider

"The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) recently developed a series of models using computational fluid dynamics (CFD) to study airflows and respirable dust distribution associated with a mediumsized surface blasthole drill shroud with a dry dust collector system. Previously run experiments conducted in NIOSH’s full-scale drill shroud laboratory were used to validate the models. The setup values in the CFD models were calculated from experimental data obtained from the drill shroud laboratory and measurements of test material particle size. Subsequent simulation results were compared with the experimental data for several test scenarios, including 0.14 m3/s (300 cfm) and 0.24 m3/s (500 cfm) bailing airflow with 2:1, 3:1 and 4:1 dust collector-tobailing airflow ratios. For the 2:1 and 3:1 ratios, the calculated dust concentrations from the CFD models were within the 95 percent confidence intervals of the experimental data. This paper describes the methodology used to develop the CFD models, to calculate the model input and to validate the models based on the experimental data. Problem regions were identified and revealed by the study. The simulation results could be used for future development of dust control methods for a surface mine blasthole drill shroud. IntroductionIn surface mines, production drilling is an essential process in blasting to fracture the hard rock overburden for removal. During the process, considerable amounts of respirable dust are produced. Past sampling at the shroud area of blasthole drills had documented time-weighted-average respirable dust concentrations ranging from 8.68 to 95.15 mg/m3 (Organiscak and Page, 1995) and 1.04 to 52.30 mg/m3 (Listak and Reed, 2007). These high dust concentrations, which may contain silica, can lead to respirable dust overexposures for the miners working nearby. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is ultimately fatal.Two basic methods are used to control drilling dust: a wet suppression system or a dry collection system (Cecala et al., 2012). Dry drilling techniques using a dust collection system are preferred in rural mining locations where a constant water supply is not available, and in the case of rotary drilling where water is associated with accelerated bit wear due to bearing degradation and hydrogen embrittlement. In addition, dry drilling eliminates freezing-related issues with water in colder climates. Dry dust collectors are highly effective at removing dust, especially the finer material, as long as they are properly operated and maintained (Listak and Reed, 2007; Organiscak and Page, 2005)."

Nov 1, 2016

By Rayner B

Five wells have been drilled in the Basker/Manta Block of VIC/P19, Gippsland Basin, resulting in sub-economic Intra-Latrobe Group oil and gas discoveries at Basker-1 and Manta-1. A total of 21 individual hydrocarbon bearing sandstones were intersected by the two wells. These reservoir sand bodies were deposited by fluvial processes in a lower coastal plain environment. The modelling of sand body orientation and geometry is a critical component in the evaluation of the two accumulations. Seismic resolution of the thin (average 2 m to 5 m) sand bodies is inadequate for mapping their orientation and distribution. Dipmeter data has been successfully applied to the problem of orienting the sand bodies using FMS images acquired during the drilling of Gummy-1 and reprocessed HDT data from Basker-1 and Manta-1. Prediction of lateral extensiveness (geometry) of individual sand bodies has also been attempted. Interpreted palaeocurrent direction from all three wells is dominantly from the NW to the SE. Reservoirs in the Manta-1/Gummy-1 area are interpreted to be predominantly channel sands, deposited by relatively low sinuosity streams. As such they would tend to have a laterally extensive, elongate geometry. Sand bodies deposited in the Basker-1 area show a predominance of laterally accreted cycles deposited by meandering streams. Channel geometry may then be limited in the downstream/upstream direction by internal permeability barriers such as clay plugs.

Jan 1, 1992

By Günter Huber, Bruno Mattle, Helmut Westermayr, Daniel Spöndlin, Max John, Nejad Ayaydin

PROJECT DESCRIPTION Alignment The Strenger Tunnel forms part of the S16 four-lane expressway between Landeckand Bludenz. The construction of this important East-West connection started in 1973with the Arlberg Road Tunnel as its key constituent. Beginning in 1992, solutions for the section between Pians and Flirsch were investigated. Efforts to conserve nature and to avoid potential avalanche and landslide areas led to a solution detouring the villages in the Stanz valley. The starting points were predetermind by the intersections at Pians in the East and at Flirsch in the West. As a result of the expected traffic load and the comparatively high gradient of 2.9%, both one-way, two-lane tubes were constructed at once. The north tube is 5.851 m long, the south tube 5.775 m, see Figure 1. Layout of Tunnel Cross-Section The tunnel cross-section was determined by 2 × 3.75 m wide, 4.70 m high roadways, two sidewalks and sufficient space for two fans above the clearance

Jan 1, 2005

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

By Lennart Mukka

The Kiruna Mine in Sweden currently has three ventilation systems. The first two (a new and old system) serve the production areas. The third system is used for the facilities on the former main haulage level 775. That area includes offices and workshops for load haul dumpers (LHD) and drill rigs. The third ventilation system also covers the crushing and haulage on level 1045. At the present time, the total airflow for the mine is 1,600 m3/sec(3.4 million cfm). The current system serves the levels above the 775 level. The new one is for the levels between 775 and 1,085 m (2,540 and 3,560 ft), which are needed for the new ore body. When all of the production is below level 775, the old ventilation system will be closed down.

Jan 1, 2002

By Robert C. Pease

Siskon Gold has started gold production at the San Juan deposit in northern California. The mine is located about 27 km (17 miles) north of Nevada City, CA (Fig. 1). It is scheduled to be-come the largest underground gold mine in California. It is situated in the western foothills of the Sierra Nevada Mountains in the Mother Lode gold belt. The property consists of 8 km2 (2,000 acres) of patented land. It is situated in a topographically high area known as San Juan Ridge, which is 213 m (700 ft) above and between the Middle Yuba and South Yuba rivers. The elevation is between 790 and 914 m (2,600 and 3,000ft) above sea level. Annual precipitation averages 1,346mm (53 in.). Most of that falls between November and April.

Jan 1, 1996

By H. Huang, R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic to neutral solutions, over the pH range 1-7, to determine a potential range for co-dissolution. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated EH-pH diagrams for the copper-arsenic-sulfur-water system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Jan 1, 2014

By I. Gaballah

The chalcopyrite ore&apos;s anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994

By R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic solutions, over the pH range 1-7, to determine a potential range for co-dissolution.. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated predominance diagrams for the copper-arsenic-sulfur system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Feb 23, 2014

By Dennis Arthur Fenton

The hydrodynamic bearing was first described by, Reynolds in 1886, and has since been widely applied in motors, engines, compressors, hydroelectric turbines, and other machinery. For various reasons, the hydrostatic bearing currently predominates in the large, horizontal rotating machinery field (e.g. grinding mills). However, the current industry trend towards increasing size and energy efficiency has resulted in renewed interest in the advantages of hydrodynamic bearings. These advantages include structural improvements, reduced bearing friction, improved bearing life, improved transient characteristics, and reduced lubricant pump size and power requirements. In particular, the higher energy efficiency results in substantial savings on large machines. This paper describes some aspects of the design of large hydrodynamic bearings based on thirty years, of experience in the design of such bearings on grinding mills ranging in journal size from 2.1 m to 6.4 m, see Table 1.

Jan 1, 1985

By Leandro de Arruda Santos

O objetivo deste trabalho foi avaliar o comportamento mecânico sob flexão de um instrumento endodôntico constituído de Ni-Ti M-Wire e comparar suas respostas com aquelas obtidas de um instrumento de Ni-Ti superelástico convencional com a mesma geometria, utilizando-se simulação por elementos finitos. Um instrumento ProTaper Universal F1 foi selecionado para este estudo. O modelo geométrico para a simulação numérica foi gerado através de micro-tomografia computadorizada e os dados para os modelos constitutivos foram obtidos por meio de ensaios de tração realizados em laboratório. A simulação numérica foi realizada em ABAQUS, com condições de contorno baseadas na especificação ISO 3630-1. Os resultados mostram que instrumentos de Ni-Ti M-Wire apresentam maior flexibilidade e menores valores de tensão quando submetidos à flexão, o que indica que estes instrumentos são mais resistentes à fadiga por flexão.

Aug 8, 2018

By William L. Fink, Dana W. Smith

In parts I1 and II2 of this series, there were presented results of investigations on the age-hardening of an aluminum-copper and an aluminum-magnesium alloy. It was shown that the simple precipitation theory of hardening3 adequately explained the aging phenomena, including certain so-called "anomalous" behaviors which had caused other investigators to reject or modify the precipitation theory. However, these papers did not discuss the double aging peaks, which have been stressed in recent articles by Dr. M. Cohen4 and Dr. M. L. V. Gayler.6 The present paper is devoted to an explanation of this "anomaly." Fig. 1 is a generalized schematic representation of aging curves at different temperatures. Curve A corresponds to the aging at the lowest temperature, and D at the highest temperature. Certain previous investigators have explained curve A and the initial peaks

Jan 1, 1938

By William L. Fink, Dana W. Smith

In parts I1 and II2 of this series, there were presented results of investigations on the age-hardening of an aluminum-copper and an aluminum-magnesium alloy. It was shown that the simple precipitation theory of hardening3 adequately explained the aging phenomena, including certain so-called "anomalous" behaviors which had caused other investigators to reject or modify the precipitation theory. However, these papers did not discuss the double aging peaks, which have been stressed in recent articles by Dr. M. Cohen4 and Dr. M. L. V. Gayler.6 The present paper is devoted to an explanation of this "anomaly." Fig. 1 is a generalized schematic representation of aging curves at different temperatures. Curve A corresponds to the aging at the lowest temperature, and D at the highest temperature. Certain previous investigators have explained curve A and the initial peaks

Jan 1, 1938

By Sakai S, Suga S, Bisque RE

Soil gases were collected on activated charcoal, analyzed by computerized mass spectrometry and treated with multivariate statistical pattern recognition to determine the diagnostic geochemical signature associated with the Okuaizu Geothermal Field in Japan. From this a geothermal model was developed and compare to 175 "unknown" samples in a 250 m spaced grid over 30 1Qn2 mapping the areas with a matching geochemical character. Faults and fractures were generally located by the presence of high molecular weight components. Following the initial survey, the faults in two specific areas were precisely located by a second survey with samples at 10-30m spacing. Where earlier geochemical surveys had placed anomalies 1-2 Km northeast of the geothermal center, the fingerprint survey accurately mapped the system and detected several faulted zones. It was not misled by hot springs located away from the geothermal System.

Jan 1, 1987

By Gary Pattrick

A new class of spongy Au catalysts is studied for the selective catalytic reduction of NOx by propene under leanburn conditions. The spongy catalyst is an unsupported powdered Au that consists of micrometer particles (~5 microns) that have nanometer scale (~10 nm) internal skeletal structures. The effects of alloying 1 ? 50 atom % platinum group metals (M= Pt, Pd, Rh) and 5 wt% first row transition metals (M = Ti, Mn, Fe, Co) were studied. Even low additions of PGMs (1 at.%) cause significant shifts to lower temperature regions of activity and the largest shift is obtained for Rh. For Rh this is interpreted as a strong synergistic interaction between Rh and Au. Possibly related to the Rh effect, Co is the only other metal studied that lowers the temperature of NOx reduction. The other first row transition metals inhibit the reduction reaction.

Oct 1, 2003