Search Documents

By Liu Run, Jia Zhao-lin, Yan Shu-wang

"Piles with diameter larger than 2m in engineering can be defined as large diameter pile, and piles used for oil platform foundation in Bohai Gulf, are usually over 100m long and 2m in diameter. Such long piles have to be manufactured by segments before installation, because of transformation and hoisting difficulties. The segments of the pile are assembled by welding during installation one to another. Normally, assembling two pile segments takes one day or even a longer time, which mainly depends on construction conditions. After pile segment assembling, it proves to be difficult to restart the successive penetration. The mechanism of pile refusal is discussed and the process of driving a segmented pile is simulated with a finite element program. The calculating results show that, when the stick-up stability was satisfied, increasing the length of the last segment of the pile and assembling the pile segments when the pile tip penetrates into a clay layer could greatly ease the difficulty of driving the pile. Furthermore, cutting down the pile extension time is also one of the most effective measures to minimize the refusal risk.1. InstructionIn recent years, more and more oil platforms with six or eight legs have been adopted in Bohai Gulf, China. The leg piles with diameters of 2m or more have to be driven to about 100m below the sea bed. Such long piles have to be manufactured by segments before installation, because of transportation and hoisting difficulties. The segments of the pile will be assembled during installation, in which a successive segment will be attached to a formerly penetrated one by welding (Fig.1). The assembling work often takes one day or even a longer time."

Jan 1, 2014

By R L. Brathwaite

The orogenic gold deposits wall poster is one in a series of posters on different mineral deposit types being produced by GNS Science to raise awareness of the characteristics of New Zealand mineral deposits and their prospectivity. Orogenic gold deposits are typically quartz vein deposits formed in fault and shear systems at crustal levels within and above the brittle ductile transition zone, at depths of 3 12 km and temperatures from 200¦ to 400¦C. In New Zealand, orogenic gold deposits are found in regionally metamorphosed sedimentary rocks of Paleozoic and Mesozoic age. The deposits in Paleozoic rocks include those at Golden Blocks in Northwest Nelson, Lyell and Reefton on the West Coast, and Preservation Inlet in Fiordland. Quartz veins are developed along shear zones that dip steeply and generally strike parallel to the axes of folding in the greywacke and argillite/slate host rocks, although most are discordant to bedding. The lodes are typically less than 1 m wide and extend an average 200 m horizontally and vertically, but the Birthday Reef at Blackwater, Reefton, the largest quartz vein deposit in Paleozoic rocks, averages 60 cm in width and was mined over a strike length of 1070 m, and to a depth of 830 m. Disseminated gold occurs adjacent to the quartz lodes at Globe-Progress and some other Reefton deposits. The deposits in Mesozoic rocks are hosted in schist of Otago and Marlborough, and schist and greywacke of the Southern Alps. The lodes are typically lensoidal, less than 1 m wide and localised along single or multiple parallel shear zones that generally dip steeply, and are discordant to the schist foliation and bedding. A notable exception is Macraes, where the lodes are developed in the semi-concordant, low angle Hyde Macraes Shear Zone that has a strike length greater than 25 km.

Jan 1, 2005

By C. Cano

One of the main concerns within the mining industry is to minimize the impact of tailing facilities to the environment and nearby communities. Since the implementation of the first thickened tailings disposal (TTD) methodology at Kidd Creek in 1964, the thickened tailing disposal has been growing alternative disposal technology to mitigate the environmental impacts. Technical investigations on the TTD technology have been studied in detail to counteract the increasing shortage of water resources. One of the benefits observed with TTD is its resistance to potential earthquakes, particularly in zones with high seismic activity (Los Andes). TTD technology optimizes the maximum possible density for the material and generates a negative internal pore pressure in the material due to the surface and sub-surface water evaporation. This internal pore pressure should be enough to resist the pores pressure to which tailings are subject due to an earthquake action. The objective of this study is to verify the Shrinking Limit (SL) of thickened tailings during initial deposition and in the long term and the ability of tailings deposited by TTD would resist liquefaction. Fresh tailings coming from a flotation process of a copper plant concentrator were used. The samples put under cyclical three-dimensional tests associated with maximum credible earthquake magnitude range of 7.0 8.0 to develop a curve for the safety factor v/s depth for dry densities related to the maximum density obtained at the SL. At a dry density of 1.65 t/m3 liquefaction did not occur at any depth. At 90 % of dry density of 1.51 t/m3, liquefaction did not occur at earthquake magnitudes of 7.0 or 7.5 nor at any depth but liquefaction occurred at magnitude 8.0 between 0 m and 14.5 m; below 14.5 m, liquefaction does not occur.

Jan 1, 2007

Downhole survey uncertainties observed at various De Beers operations prompted an investigation into their possible effect on deposit shape and volume. An accurately surveyed artificial æboreholeÆ was constructed and different downhole survey instruments tested. In this way an empirically determined error range of 0.1 per cent to ten per cent was derived for downhole survey data. These survey errors were applied to an orebody model at an existing mine. Visualising the sphere of uncertainty associated with a borehole trace using a general mining package (GMP) gives an indication of possible volume variance. The resulting orebody maximum and minimum volume scenarios for three different depths (200 m, 500 m and 800 m) are presented. For certain instruments and borehole angles, the 3D positional error can be as high as 100 m at 1000 m down the hole. At depths below 200 m the resulting volume deviations can become significant for borehole survey errors exceeding 0.35 per cent. At 800 m depth the volume difference can approach 25 per cent. These figures assume that the error is compounded. The impact of these downhole survey errors is greatest for pipe-like orebodies such as porphyries and kimberlite pipes. Subhorizontal sill-like orebodies (and coal seams) will not be significantly affected by these errors. The impact of this type of survey error needs to be stated (and quantified) and is significant in JORC classification.

Jan 1, 2009

By J, T C. McCuaig, J Hodgkison, T Fouet

Olympic Dam is the eighth largest Cu deposit and the largest U deposit in the world, with approximately 35 million tonnes of contained Cu and 1.2 million tonnes of U. The most recent resource estimate was for 2.95 billion tonnes of mineralised material with average grades of 1.2 per cent Cu, 0.4 kg/t U, 0.5 g/t Au, 2.6 g/t Ag as contained mineral resources. Olympic Dam is expected to produce >200 000 tonnes of Cu and 4200 tonnes of U3O8 from 9.8 million tonnes of ore in 2004, making it the 12th largest Cu producer in the world. One of the impediments to achieving targeted rates of production has been oversize material (>0.9 m) reporting to stope draw points. A major contributor to oversize material may be overbreak along pre-existing structural weaknesses from stope walls and backs during the production life of a stope. Underbreaking to structures can also have a detrimental effect on the performance of a stope. In an effort to understand the influence of structural geology on stope performance, WMC Resources and SRK Consulting partnered during 2003 to refine the current system of structural mapping, and to use historical data to produce a structural interpretation covering a large part of the mining area. The interpretation has been wireframed in DATAMINETM into a three-dimensional structural framework model. To date, there are more than 600 structures of >50 m strike length incorporated into the structural framework model, which covers a study area 1500 m + 600 m + 350 m. A back-analysis exercise to assess the influence of interpreted structures on overbreak and underbreak was completed for laser-surveyed stopes.

Jan 1, 2004

By Paolo M. Brion, Z. Bade Sozer

"The Bypass Tunnel has high head conditions ranging from a minimum of 600 feet (183 m) under the Hudson River to a maximum of 875 feet (267 m) on the west side. The ground cover ranges from 425 feet to 900 feet (130 to 274 m). A two-pass lining is designed for the Bypass Tunnel. The bolted, gasketed precast segments carry the temporary hydrostatic and permanent ground loads. After the tunnel is put into service, the design assumes that the final lining, which varies from reinforced concrete to reinforced concrete with steel interliner, will carry the permanent hydrostatic loads. The design head for the segments is assumed at 775 feet (236 m), and the internal operating pressure head is around 1,200 feet (366 m). This paper discusses the design hydrostatic head and different load conditions considered for the segments, the load sharing between the segments and final lining, and the means employed to control water and hydrostatic pressure. PROJECT BACKGROUND The Rondout-West Branch Tunnel (RWBT), a segment of the Delaware Aqueduct, was built from 1937 to 1944 and provides about 50% of New York City’s total water supply. Monitoring and tunnel operations have shown that the RWBT is leaking up to 35 million gallons per day (MGD) (132.5 million L/day). In particular, two locations have been identified as areas of concern: Roseton and Wawarsing, as shown in Figure 1. The Wawarsing reach of the aqueduct will be repaired with an extensive grouting program when the RWBT is unwatered. However, because of the extensive nature of the leakage in the Roseton area, a Bypass Tunnel will be constructed to divert the flow around this area."

Jan 1, 2016

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

By S. Banisi, A. R. Hasankhoei, Gh. Parsapour, A. R. Ghasemi

At the Gol-E-Gohar mining and industrial Company, a pelletizing plant, which includes two parallel dry closed grinding circuits and a pellet production circuit, produces 600 t/h. Each grinding circuit consists of a burner, a dry ball mill (6 m×13 m) and an air separator. Each ball mill consists of a 2 m-long dryer chamber and an 11 m-long grinding chamber. Iron ore concentrate is fed to the drying chamber to decrease its moisture from 2.5% to below 0.2%. The drying chamber consists of 56 flights in two rows. It was found when the feed moisture content decreased from 1.3 to 3.5%, the throughput decreased by 14% (40 t/h) indicating a low performance of the dryer. In order to improve the efficiency of the drying section, a scale down version of the dryer was constructed in a 1m diameter mill with a transparent end to make image analysis possible. It was found that because of the inappropriate veiling profile in the drying section, most of materials are not subjected to the hot gas tunnel. To overcome this problem, various flights with different geometries were physically tested and also simulated by the KMPCDEM © software. With the aim of arriving at a proper veiling profile which maximizes the particles contact with hot air, a new flight design was obtained and tested. The installation of the rectangular tooth type flights in one of the mills in the plant made the comparison of the old and new designs possible. The evaluation of the designs in a period of three months indicated 15 t/h increase in the throughput in the case of the new flight design.

Jan 1, 2016

By A. J. Keen

"Cominco's Polaris Mine is an underground lead/zinc operation located on Little Cornwallis Island in the Canadian High Arctic. Polaris is the world's most northerly base metal mine, situated at about latitude 75°N and longitude 97°W (Fig. 1). The closest community is Resolute Bay about 100 km to the southeast.During the construction and development phase Cominco adopted a unique scheme to save time and money. Many facilities including concentrator, powerhouse, shops and warehouse were built on a barge in southern Canada. The barge was towed 4800 km to the site in August 1981. Production at Polaris began in November 1981. The current mining rate is 1 million tonnes per year. The mine employs 250 people with about 190 on site at any time.GeologyThe deposit is a Mississippi Valley type orebody and lies near the top of the Ordovician Thumb Mountain Formation. Ore minerals consist of sphalerite and galena with the gangue being predominantly dolomite with calcite and marcasite. The orebody is situated completely within permafrost, consequently the voids frequently found in the ore are filled with ice. The orebody strikes north-south, dips approximately twenty degrees to the east and takes up an area about 400 m wide by 700 m long. The upper portion of the orebody (60 m to 150 m below surface) lies in an area called the Panhandle Zone. The deeper portion of the orebody known as the Keel Zone extends to 300 m below surface (Fig. 2). The deposit is strongly zoned with a high grade zinc/lead and iron-rich tabular core overlain and underlain by vein, stringer and breccia mineralization. The ore reserves at January 1991 were 14.6 million tonnes at 3.6% Pb, 13.7% Zn, 3.2% Fe, after producing 8 million tonnes at 3.9% Pb and 14.2% Zn since November 1981"

Jan 1, 1992

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016

By C. Douglas Lee

This case study describes the work done at the University of Arizona on the development of a computer mine model for an irregularly shaped and spotty ore deposit. The purpose of the work was to develop techniques for modeling any highly irregular deposit, for which the regular 3D fixed block model is not well suited. The deposit contained complex geology consisting of sedimentary beds that had been faulted, thrusted, and intruded by igneous rocks (see Fig. 1). The physical dimensions of the modeled ore body were 1067 m (3500 ft) along the N-S direction and 914 m (3000 ft) along the E-W direction. Topographic relief in the modeled area was approximately 274 m (900 ft). The highest grade of ore was found near the surface with mineralization extending down to approximately 152 m (500 ft) below. Using a fixed bench height of 12 m (40 ft), the model required 25 levels with the highest elevation being at 1286 m (4220 ft). Fig. 2 shows a cross section of the developed computer model of the ore deposit. The particular modeling approach selected for this deposit was the 3D irregular block model.* This meant that only the dimension of bench height was fixed at 12 m (40 ft). Irregular size blocks in the form of polygons were adopted in the model to describe the ore zones and geologic contacts. The following sections of this chapter describe some of the techniques used in modeling.

Jan 1, 1979

By Theodore R. Butkovich, Jesse L. Yow

Geological storage of spent-fuel assemblies from an operating nuclear reactor has been underway since the Spring of 1980 at the U.S. Department of Energy's Nevada Test Site. The primary objective of this generic test is to evaluate granite as a medium for deep geological storage of high level reactor waste and to provide data on thermal and thermomechanical behavior of granite from imposed heat loads.(l) The underground installation in the Climax stock granite was sited at about 420 m below the surface and 145 m above the existing water table. As shown in Figure 1, three parallel drifts were excavated spaced on approximately 10 m centers. Seventeen storage holes were drilled at the central drift on 3 m centers in which eleven spent fuel canisters and six thermally identical electrical simulators were emplaced. Electrical resistance heaters were emplaced in vertical holes in the floor of the side drifts on 6 m centers. The thermal output of these heaters is being periodically adjusted to simulate the thermal response of a large storage array. Rock and ventilation air temperatures are being measured continuously in the drifts and throughout the rock surrounding the excavations. Measurements of drift deformation have been made routinely since the emplacement of the spent fuel. Both vertical and horizontal measurements are being taken at five locations along the heater drifts and at six locations along the central canister drift (Fig. 1). Two types of instrumentaton are being used: convergence wire extensometers which are monitored automatically, and a manually operated tape extensometer with which measurements are taken periodically. The tape extensometer measurements were initiated about 6 weeks following fuel emplacement. The lack of a temperature correcting capability for the convergence wire extensometers make that data unavailable for analysis at this time.

Jan 1, 1982

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia's original Ertsberg openpit copper mine. In spite of Grasberg's remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia's (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl's six ore deposits are all located within a 10- x 10-km' (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island's southern coast. A 118-km (74-mile) access route connects FT's port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project's central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world's longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

The main aim of this work is to evaluate whole-body vibration (WBV) of dozer operators based on three sitting postures (i.e., with 15° lean forward inclination posture, vertically erect posture with no inclination, and with 15° lean backward inclination posture) in Indian surface coal mines. A seat pad tri-axial accelerometer was used to collect WBV data from six dozer operators for three different sitting postures. Results showed that except for Dozer-1, 2, 4, and 5 operators during lean forward sitting posture and Dozer-4 operator during vertical erected posture, no other dozer operators have exceeded an exposure limit value (ELV) of 1.15 m/s2 in any of the considered sitting postures. Similarly, the vibration dose value (VDV) based on exposure action value (EAV) of 9.1 m/s1.75 has surpassed for all the dozers. But no dozer operator has exceeded an exposure limit value of 21 m/s1.75. The outcome of the study infers that based on “above health guidance caution zone (HGCZ)” for daily vibration exposure, i.e., A(8) measurements, for the operator sitting in lean backward postures the vibration amplification was reduced by 32.89% less compared with lean forward posture and 16.23% less when compared with vertically erected posture. Similarly, based on VDV(8), the exposure to vibration for the lean backward posture was reduced by 33.34% when compared with lean forward posture and 17.11% less when compared with vertically erected posture. Based on the above observation, it is concluded that lean back inclination with a trunk flexion of 15° is a favorable sitting posture, as it exposes the dozer operators to minimum vibration.

By Xuhui

Pile foundations are underground projects which are carried out under complicated site conditions, so it is difficult to summarize their characteristic patterns from the everchanging practical pile foundations. In combination with theories, the paper analyses the effects of sound reinforced concrete piles and various types of defective piles on the propagations of stress waves. Through testing on prototype pile models, by use of the transient dynamic method and comprehensive analysis in both time domain and frequency domain, their reflection characteristics and patterns are acquired. In addition, discussions are carried out in combination with some real projects. Our model tests include comparison of large scale pile models of 20X20cm in cross section, 5. 0m in length respectively in air, standard sand, and natural stratum; prototype model tests of digged piles of 0. 7-1. 2m in diameter, and 18m, 30m in length; prototype model tests of bored piles of 0. 6m, 0. 8m in diameter, 12-20m in length. Test results show that no matter in air or buried in medium, the intrinsic characteristics of sound piles and various types of defective piles are fixed. In their time domain waveforms and spectral diagrams, obvious regularity are shown, which proves that the relations between the pile natures and their dynamic responses are fixed, which provide basis for correct judgement of pile soundness and natures of defective piles.

Jan 1, 1991

By Chuan-fu Zhang

Li(Nil/3Col/3- xMnl/3)MxO2(M=Ti, Mg) cathode materials were prepared from LiOH?H2O and oxalate precursor. The physical and electrochemical properties were studied by XRD, SEM, cyclic volt-ampere (CV), AC impedance and constant current charge-discharge. The results show that crystal volume of Ti4+ or Mg2+ doped sample is increasing and the electrochemical reaction resistant Rct is decreased at high rate, improving the cyclic performance and rate capability. The effect of Ti4+ doped is better than Mg2+. The sample is well crystallized and simple pure phase with a-NaFeO2 layered structure when doping quantity x=0.025. The second specific discharge capacity of Li(Nil/3Col/3- 0.025Mnl/3)Ti0.025O2 is 143.2mAh/g at 1C,128.0mAh/g at 2C in the voltage of 2.75-4.3V,and still has 140.7mAh/g and 121.7mAh/g after 20 cycles, respectively, keeping 98.25%, 95.07% capacity.

Jan 1, 2009

By D. C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required placement of approximately 3,000,000m3 of fill over a P1an area of approximately 600,000m in irregular terrain with relief of up to 40m. Earthwork construction was completed in approximately six months using mine waste which was placed in 4 to 6m lifts using mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10m to enable development of a mat and additional resistance to possible differential settlements under dynamic (earthquake) conditions. A single 80 mil (2mm) HOPE liner was used below the leach pads and this was protected from the loading and unloading equipment using an engineered liner system consisting of screened sand, gravel and silt from local sources as the bedding and cover layers, and a heel of screened gravel and primary crushed low grade ore. Settlement monitoring, field testing and subsequent assessments of liner performance have indicated an adequate design was achieved and the project proceeded with considerable savings in time and construction costs.

Jan 1, 1995

By Leandro Brunholi Ramos

Foi estudado o efeito da temperatura no comportamento à corrosão sob tensão do aço inoxidável dúplex AISI 318 em solução contendo 115.000 ppm de cloreto, pH4 a temperatura ambiente e a 70°C. Ensaios de tração com baixa de taxa de deformação foram realizados. Foi avaliada a susceptibilidade do aço inoxidável dúplex AISI 318 à corrosão sob tensão no potencial de circuito aberto e em vários potenciais anódicos e catódicos. Os resultados mostraram que a redução do alongamento variou com o potencial aplicado. Os resultados experimentais mostraram que o aço AISI 318 ficou imune à corrosão sob tensão em potencial entre -750 mVECS e 1.000 mVECS na temperatura ambiente e entre -650 e -100mVECS para a temperatura de 70°C. Em potenciais maiores que o potencial de pite observou-se uma redução drástica no alongamento em ambas as temperaturas. No entanto, quando os potenciais aplicados foram abaixo de -650 mVECS para a temperatura de 70°C e -750mVECS para a temperatura ambiente, houve uma redução no alongamento final até a ruptura, provavelmente através do processo de fragilização por hidrogênio.

Aug 8, 2018

By Thamiris Auxiliadora Gonçalves Martins, Karen Espina Gomes, Amilton Barbosa Botelho Junior

The present work aims at the synthesis of nanoparticles of copper by chemical reduction in microwave oven. The solution used comes from the selective copper precipitation of the lateritic nickel leachate. The copper solution (20mL) was placed in a beaker, and 2mL of 100g/L ascorbic acid and 20mL of 20g/L sodium citrate were added in that order and at room temperature. The pH of the mixture was corrected with 1M sulfuric acid or 2M sodium hydroxide. Then the mixture was placed in a microwave oven. The effect of pH, time and microwave power were evaluated. The morphology, composition and size of the particles were verified in Scanning Electron Microscopy with Energy Dispersion Spectroscopy (SEM/EDS). Results showed that the particles formed had no nanometric size. This may have occurred because the reducing action of ascorbic acid together with sodium citrate generates a very rapid reduction rate, which makes it impossible to form particles on a gauge scale. Particles synthesized at pH 4, after 4 minutes of reaction with 1000W of power presented particles with spherical morphology and only copper in the composition.

Oct 3, 2019

By M. G. Bakker, D. D. Murphy, D. R. Spears

The US Bureau of Mines studied the mechanism of shear flocculation of silica with stearic acid. At pH 6 and 12, shear flocculation of silica was not observed with the addition of up to 4.5 x 10-4 M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations = 10-4 M (22.5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labeled with a doxyl group. The presence of the spin-labeling group did not greatly affect the shear flocculation properties of stearic acid. Adsorption of labeled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicated that the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-5 M (22.5 lb/st). The results are discussed in terms of a possible mechanism for shear flocculation.

Jan 1, 1995