Search Documents

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011

By A. S. Prokopovitsh

A spectrophotometric method for the determination of small amounts of copper in tungsten metal powder using the principle of solvent extraction has been developed by the Federal Bureau of Mines. The metallic sample is dissolved in hydrogen peroxide, tartaric acid added, the pH adjusted, and the excess peroxide destroyed by boiling. Copper is reduced to the cuprous state, and the reagent neocuproine (2,9-dimethy1-1,10-phenanthroline) is added to form a colored complex with the copper. This colored complex is then extracted into chloroform and the absorbance of the separated chloroform layer measured on a spectrophotometer. Copper contents as low as 1 p.p.m. (parts per million) can be determined. The method is limited to finely divided tungsten powder. The interest of the Bureau of Mines in developing more sensitive methods for the determination of trace impurities in high-purity tungsten prompted an investigation of the possibility of using solvent extraction-colorimetric methods. The organic reagents now commercially available make possible many extremely sensitive colorimetric methods for the determination of metallic ions. Extraction of the colored complex into a small volume of organic phase can be used to further increase sensitivity (4) .4/ This general approach has the added advantage that no special equipment beyond that normally found in an analytical laboratory is required.

Jan 1, 1961

By M J. Saynor, J B. C Lowry

The Ranger Uranium Mine is located in the wet-dry monsoonal tropics approximately 250 km east of Darwin in the Northern Territory of Australia (Figure 1). Mining of open-cut ore bodies commenced in 1980 (Pit 1) and ceased in 2012 (Pit 3) and milling and production are scheduled to cease by 2021. At the conclusion of mining and milling operations, mine tailings will be returned to the mined out pits 1 and 3, which must then be physically isolated from the environment for at least 10,000 years (Australian Government 1999). The final landform also needs to have sufficient mitigation measures in place to ensure that areas downstream are not impacted by erosion products from the mine site. The proposed post-mining rehabilitated landform will cover approximately 847 hectares (8.5 km2) which represents an area that has the potential to supply sediment to catchments and streams downstream. One method of reducing runoff and associated sediment is the construction of rip lines along the contour to slow down the runoff velocity and to also trap fine sediment and nutrients in the depressions to assist vegetation growth.CITATION:Saynor, M J and Lowry, J B C, 2018. The impact of rip lines on erosion at the Ranger Mine Site, in Proceedings Life-of-Mine 2018, pp 150–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

The HYC mineral deposit at McArthur River is about 1.5 kilometres long by 1.0 kilometres wide and 55 metres thick, and contains 227 000 000 tonnes of ore of average grade 9.2% Zn, 4.1% Pb and 41 g/t Ag. Major studies have been carried out continuously since 1955 over the deposit and in the general region. This work is continuing. A small underground mine was developed by driving a decline tunnel to intersect the mineralization 80m below the surface. This provided a fully representative sample of the total deposit unaffected by weathering or oxidation, and was available for the major test program carried out in a pilot plant built to determine the full metallurgical charac- teristics of the ore. The pilot plant operations followed investigations by research institutions, both in Australia and overseas, into the problems of this ultra-fine grained ore. The ultra-fine grained nature of the ore required grinding to an average size of 95% passing 37 micro metres or 400 Tyler mesh. A major feasibility and environmental report was submitted to the government covering all aspects of a development program. The geological, engineering, metal- lurgical, economic, cultural and environmental submissions contained in this report were studied by external consult- ants employed by the government, who agreed with the conclusions that the McArthur HYC deposit is at present Uneconomic.

Jan 1, 1984

By Laing W. P, Neill D. M, O&apos

The Reward polymetallic massive sulphide deposit occurs 35 km south of Charters Towers, adjacent to the Highway gold deposit (Fig. 1). It is hosted within rhyolitic lavas and interlayered volcaniclastics of the Cambro-Ordovician Mt Windsor Volcanics. Reward is a "blind" deposit discovered in 1987 after a long history of exploration by various companies in the area. The main pyrite dominant massive sulphide body occurs under 100m combined thickness of Tertiary fluviatile sediments overlying deeply weathered gossanous volcanics. The exploration case-history provides a striking example of how geological and structural models can be built up almost exclusively from drill information. Four different styles and ages of mineralisation are present: 1) volcanogenic Cu+Pb+Zn+Ag+Au massive sulphides of probable syngenetic origin; 2) remobilised Cu+Au in massive pyrite of metamorphic/deformational origin; 3) supergene and 4) oxide Cu+Au mineralisation of weathering origin. The massive pyrite body, containing chalcopyrite lenses, transects the stratigraphy and is inferred to contain in excess of 5 million tonnes. Overlying the primary mineralisation a supergene chalcocite rich zone contains a measured/indicated resource of 634,231 tonnes of 6.77% Cu which includes 287,000 tonnes of 1.32 g/t Au and 18 g/t Ag. In addition a measured/inferred oxide resource of 309,000 tonnes of 5 g/t Au and 27 g/t Ag overlies the supergene zone.

Jan 1, 1989

By H. Köse, C. Tatar, C. Helvaci, F. Simsir

The Çayirhan coal basin is located 124 km (77 miles) west of Ankara,Turkey. With approximately 520 Mt (570 million st) of lignite reserves, the Neogene Çayirhan basin is one of the important coal districts of the central Anatolia region. The Çoraklar formation consists of crossbedded sandstone, channel fill conglomerates, mudstones, carbonaceous shales and volcanoclastic pebblestones, which are fluvial in origin. The lower and upper lignite seams occur, respectively, in the lower and the uppermost parts of the Çoraklar formation. The lignite deposits are in the Çayirhan and Koyunagili portions of the Beypazari Neogene basin. The Çayirhan coalfield consists of lower and upper lignite seams. The lower lignite seam does not outcrop at the surface. Its lateral discontinuity and relatively low sulfur content, plus sedimentologic and stratigraphic features of the associated sediments, indicate a fluvial origin. Thus, the lateral spreading and geometry of the lower lignite deposits were controlled by the channel, flood plain and well drained marshes of a fluvial system. The mining method employed at Çayirhan is the fullymechanized, retreat, working longwall with caving system. Due to ventilation, haulage and tectonic conditions, panel lengths from 0.6 to 1.7km (0.4 to 1.1 miles) are chosen, and 220-m (720ft) face lengths are used. The annual coal production is 2.2 Mt (2.4 million st).

Jan 1, 1994

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By Levent Ozdemir, Gerald Dollinger

An extensive series of linear and rotary cutting tests were run in soft and medium strength rocks at the Earth Mechanics Institute of the Colorado School of Mines to investigate the possibility of very high speed mechanical excavation for tunnel, raise, and shaft boring. The results of these tests demonstrate that cutter penetrations of 38.1 mm (1.5 inch) and cut spacings up to 228.6 mm (9 inch) are possible in such rock without exceeding the bearing capabilities of the cutters. It was also demonstrated in vertical boring tests that continuous excavation rates up to 38.1 m/hr (125 ft/hr) can be achieved with state-of-the-art technology provided sufficient thrust and torque is available. A predictor model for soft rocks was also developed using the test data. Analysis of this model shows that the errors between the predicted and observed cutter normal loads appear to be independent of cutter diameter, tip width, cut spacing, and depth of penetration. This suggests that the structure of the model is correct with respect to these variables. An analysis of the coefficients in the model was also made and a correlation found between the principal coefficient and Unconfined Compressive Strength. The second coefficient in the model was found to be similar in magnitude to rock properties such as Brazilian Tensile Strength, Shear Strength and Point Load Index.

Jan 1, 1989

By John Dasher

Extrapolation is a useful technique, but it can be overdone. Seldom is it justified to study over a range of 1 to 6 and extrapolate the results to 150,000. It is especially dangerous if the extrapolation is based on a false assumption. The authors assume settlers scale-up by residence time rather than by area, admit their result (a settler depth of 7 m) is "unreasonable" and suggest longer, wider, shallower settlers might be better. Various authors have noted for a copper-LIX system a total flow basis of 2 gpm per sq ft for sizing settlers. The results of this are compared with those in the paper in [Table 7]. The authors note that flooding of their settlers was never approached. Thus the smallest unit calculated is understandably twice too big. The largest however, is 5% of the required size. I note that the figures in [Table 6] for 1/min/cm2 are based on plan area rather than cross section as titled and are wrong by l0 4. A flow of 2050 1/min/cm2 is about Mach I. It is also 10 5/3 or 46.5 times that of the little one, although the abstract says the design was based on constant flow rate per unit cross section.

Jan 1, 1977

By Louis M. Schlesinger, Joel F. Hutwelker

A pilot plant was constructed to attrition scrub and deslime North Carolina phosphate ore. A 15.2 cm (6 in.) diameter pilot-scale Linatex Hydrosizer was used for desliming. Four tests were run at a throughput of 2.9 t/hr/m2 (0.30 ton/hr/f t2) and a teeter bed density of 1.12-1.13 g/cm3. The teeter water flow rate was varied to create an upflow velocity ranging from 0.25-0.47 cm/s. (This latter value is equal to the terminal settling velocity of a 200 mesh (74 micron) particle having a density of 2.7 g/cm3.) The recovery of +200 mesh oversize to the sizer underflow was 95%-96%, regardless of the teeter flow rate. The recovery of -200 mesh undersize to the sizer overflow increased from about 90% at 0.25 cm/sec to 100% at 0.47 cm/sec. A metallurgical balance that was conducted for one of the tests showed that less than 2% of the phosphatic value was lost to the overflow. A fifth test was run using an upflow velocity of 0.47 cm/sec; however, the teeter bed density was maintained at 1.05 cm/sec. This change had the effect of reducing the cut point (d50), while maintaining complete slime removal.

Jan 1, 1993

By John R. Marks

The first 0.7 m3 (1 cu yd) diesel load- haul-dump vehicle (LHD) arrived at the Homestake Gold Mine in Lead, SD in I969 to muck a ventilation drift. Others soon followed. Mechanization has subsequently changed stoping methods, manpower requirements, ventilation practice, the definition of minable reserves, and it has impacted safety and health. These have all had a direct bearing on the economics of producing gold ore from deep underground. Mechanized mining Before mechanization, production quotas at Homestake were met by several open cut-and-fill (OCF) mining methods. OCF mining relied on jackleg and wagon drilling, electric and compressed air slushing and cribbed raises brought up through the fill. Even square- set stoping was used until about eight years ago. The mine became 100% mechanized in 1988. The two current stoping methods are mechanized cut-and-fill (MCF) and vertical crater retreat (VCR). In 1992, MCF accounted for 54’S, VCR for 44% and development/uphole for 2% of the 1.4 Mt (1.55 million st) of underground ore produced. These methods are typically ramp- based and use diesel-powered LHDs, trucks, pneumatic drill jumbos and utility vehicles. Electric LHDs and rubber-tired compressed air muckers have also been used in VCR scrams. Pfarr (1991) and Mitchell (1980) provide good overviews of current production methods.

Jan 1, 1993

By Vinton A. Garbesi

The construction involved in the Washington Metropolitan Area Transit Authority (WMATA), Contract No. lK0011 (K-1), encompassed some 2,621 meters of single track parallel tube rapid transit tunnels, 335 meters of cut-cover subway station and appurtenant ventilation structures at each end, and a fan shaft at approximately the mid point of the tunnels. The construction contract was awarded June 7, 1974 to a Joint Venture consisting of Intercounty Construction Corporation, Hyattsville, Maryland, and S $ M Constructors, Inc., Solon, Ohio. The former being responsible for performing the cut and cover construction, and the latter being charged with constructing the running tunnels and fan shaft at their mid point. (See Fig. 1) The problems of mining and supporting, the 183 meters of twin tunnels just east of Court House Square Station, by unique mixed face and soft ground mining methods is the main subject of this report, although a general review of the tunnels in their entirety, as well as the geology encountered in the excavations, is presented to give a better overall setting for the problems encountered. GEOLOGIC SETTING The tunnels for the K-1 contract are located in three general types of material; the first being fractured and metamorphosed ignious rock (quartz-hornblende-biotite gneiss), the transition zone between weathered and competent rock, and in ground consisting of the weathered

Jan 1, 1979

By Wu Y, Qu Q

The Central Coal Mining Research Institute has developed the MAE acoustic emission monitoring system, the BD4-1 portable acoustic emission monitor and the MRB rock burst monitoring system. In the MAE system there is an IBM-PLAT, a receiver and 16 channels and the investigating range is 100 m. The main functions are detecting acoustic events from the working faces, periodically making statistics, prints, displays and storing of the results, and performing the off-line process such as drawing the curves of acoustic activity. The BD4-1 instrument has four channels, it works for more than 24 hours continuously, and keeps the data for more than 30 days after power tum-off. The BD4-1 is suited to the monitoring for a long or a short time as a fixed point where the system is invalid, especially to the monitoring of the acoustic activity promoted by the blasting. There is an IBM-PC/AT, a receiver and 16 channels spread 10 km in the system MRB. The system could on-line collect microseismic events throughout the whole mine, calculate the source location and the energy, and off-line draw the seismic activity draft of time-based or distribution in space. In practice, the forecasting is successful by using the acoustic emission and microseismic monitoring system and the portable instrument.

Jan 1, 1991

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By Ahmed H. Bukhary, Naser A. Al-Shayea

The objective is to assess the overconservatism in the parameters used for designing offshore piles. Methodology includes analysis of shaft friction data obtained from more than five different locations in the Arabian Gulf, consisting of 40 piles to depths up to 86 m. Reports were collected for both the dynamic pile monitoring system (DMS) and their corresponding geotechnical reports based on the American Petroleum Institute (API). The values of shaft capacity for the sand layers were analysed by comparing those based on API to the corresponding DMS values. Results of the comparison of the data from these reports showed that the pile design parameters obtained using API guidelines is generally smaller than that measured by DMS. The difference is presented in terms of an overconservative factor (OCF) which is adjusted based on statistical nonparametric test performed on the two data sets. The adjusted OCF were found to be 1.79 and 2.00 for carbonate sand at (loose to medium dense) and (dense to very dense) conditions, respectively. The corresponding values for silica sand were only 1.2 and 1.06. In conclusion, based on the evaluation conducted for data from these reports, the API shaft friction is overconservative for carbonate sand. The API shaft friction for piles in sand can be increased by multiplying it by the adjusted OCF.

By O A. Aladejebi, S Mitra, T Singh, D O’Dea, S, T Honey

Granulation of the iron ore blend and the additives is the foremost step in the agglomeration of iron ore fines to achieve a permeable bed during sintering, which is crucial for sinter productivity. This study investigated the granulation of four types of blends to determine the impact of granulation on bed permeability. The blends were granulated in a rotating drum at various moisture contents and their JPU permeability was measured at each moisture content in a permeability pot (diameter 95 mm and height 500 mm) at various flow rates. Several independent experiments were carried out to investigate the changes in permeability when mixtures of different particle size range (-1 mm and +1 mm) were introduced into a packed bed with a larger particle size range (-6.3 mm to +4.0 mm). The results revealed that the addition of particles in the -1 mm size range had a more pronounced negative impact on permeability compared to particles in the +1 mm size range. This can be attributed to the relatively higher energy losses (mainly inertial) associated with the presence of -1 mm particles in the mixture. The findings were used to quantify the granulation process based on the -1 mm particle size fraction in the granulated mix and their utilisation (denoted by UI-1 mm). For achieving optimal permeability in a specific blend, it was found that a UI-1 mm (utility index of -1 mm particle size) ranging from 0.82 to 0.92 was required. However, exceeding a UI-1 mm value of 0.95 resulted in weaker granules prone to deformation and led to decreased bed permeability. The study also showed that the UI-1 mm was highly dependent on the water addition per kg of -1 mm in dry feed and suggested adding ~80 to 110 mL of water per kg of -1 mm in dry feed to attain the best possible permeability. Additionally, the research proposed a mechanism involving the melting of granules at high temperatures and highlighted the influence of -1 mm particles on bed permeability during the sintering process.

Sep 18, 2023

By Seung-Kyu Son

Environmental properties of the northeast Equatorial Pacific along 131.5 degrees west, between 5 degrees and 13 degrees north latitude, were investigated in association with changes in water column structures during the summer seasons of 1998 and 1999. Climatic disturbances such as El Nino and La Nina, should have affected this area during the study period. In 1998, a thermocline where temperatures rapidly decrease with depth, was formed at 90~110 m water depth. However, in 1999, a very fluctuating thermocline was observed with latitudes. As a result of changes in the water column structures, biological and chemical environment also showed fluctuation parallel to the changes in other physical parameters. Inorganic nutrient depleting areas, especially for nitrate+nitrite and phosphate, or oligotrophic regions were extended down to approximately 100 m depth, which coincided with the surface mixed layer depth. In the euphotic zone, depth integrated nitrogen (N) and phosphorus (P) values were 34 g-N/m2 (grams of Nitrogen per square meter of sea floor), 7 g-P/m2 in 1998 and 130 g-N/m2, 18 g-P/m2 in 1999, respectively. The results indicated that nitrogen (96 g-N/m2) and phosphorus (11 g-P/m2) are supported by up-welling and down-welling phenomena with convergence and divergence in the study area. Biological parameters in the water columns were largely determined by the physico-chemical environmental parameters. Subsurface chlorophyll maximum layers were coincided with the formation of seasonal thermocline. Copepods were the dominant group of zooplankton community at three sampling stations (N5, N6, N10) terms of abundance, which was the same results of previous surveys for the past 3 years. Among copepod populations, Oncaea sp., Oithona sp. Clausocalanus sp., Acarocalanus sp. and juvenile copepodites were dominant Appendicularians, foraminiferans and radiolarians were also dominant. To investigate diel vertical migration pattern of zooplankton, repeated samplings from the water depth of 0~50m and 50~200m were conducted at KODOS (Korea Deep Ocean Study) area before and after sunrise. Zooplankton abundance was slightly higher after sunrise than before sunrise in the surface layer. Chlorophyll-a concentrations were relatively low as the concentration of sediment increased in most experiments possibly due to a decrease of grazing pressure of microzooplantkon such as ciliates, which is the efficient grazer on small-sized phytoplankton. Because copepod predation on microzooplankton may be prevented by the high concentration of sediment, resulting in lower grazing pressure on small-sized phytoplankton. The results obtained during the baseline study as a part of KODOS project since 1998.

Jan 1, 2001

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By Yoshio Hiramatsu

In Toyoha mine near Sapporo, the ground temperature is very high, perhaps due to inflow of hot mineral water, the origin of which may be rock masses intruded by the igneous activity in the Tertiary period. The rock masses are found about 2 km east of the mine, their temperature being estimated at from 770 to 870 K at a depth of 3 km. In this mine several veins bearing zinc and lead ores have been mined down to the depth of 300 m from the level of the main entry, of which altitude is 551 m above the sea level. Formerly no attempt was made at development of the deeper part of the mine than the 350 m level from the main entry. Let us indicate hereafter the levels in this mine in such a way that the level 300 m deep from the main entry is denoted as 300 mL. Since 1974, however, the 450 mL of Tajima vein has been developed by deepening No. 5 Shaft to, and by driving drifts in the level. Much hot mineral water has been flowing into the drifts from rock. After twenty-eight months from the beginning of development, the total length of excavation amounted to about 1300 m. The success in development so far may be attributed to cooling rock and air with chilled water and to adopting heat-resisting explosives and detonators. This cooling costed very much and for further development in this level a more effective and economical cooling is desired if possible. To obtain fundamental data for designing an economical cooling, the authors investigated, as a preliminary study, the heat balance in the main drift of 450 mL, by measuring the temperatures of air, rock, hot mineral water, the rates of flow of air and water and so on, in August 1976. They are now carrying out continual measurements of the variations in rock temperature, air temperature and humidity with time. The present paper describes the details of the preliminary study.

Jan 1, 1980