Search Documents

By K. Whiting, R. Huffsmith, R. Olsen, D. Adams

Long-term closure alternative selection for heap leach pad effluent is a daunting task. Passive water treatment, if designed with enough long-term capacity, can minimize long term O&M while meeting water quality objectives. Leach pad effluent from a 30-acre leach pad at Basin Creek Mine, Basin, Montana was targeted for long-term water treatment using a passive water treatment system. The objectives and results of design and construction are: 1. Design a long-term passive system utilizing existing infrastructure. 2. Construct a field scale pilot test at the mine site.

Jan 1, 2002

By A. K. Schellinger

1. In the United States, the industrial application of centrifugal force for separating phase constituents has been confined almost entirely to aqueous systems at room temperature. This paper presents results for experimental tests on the use of centrifugal force for separating the liquid and solid phases in molten nonferrous alloys. 2. The development and use of a small centrifuge for treating molten metals is described. The centrifugal apparatus was, in essence, a 3-inch diameter spinner pot, which revolved, within -a gas -fired furnace, at speeds up to 3,000 r.p.m.

Jan 1, 1953

By Keiichi Fujita, Michio Miyoshi, Hisashi Miyazaki

In the construction of "Hamacho" subway station (Tokyo Metropolitan Rapid Transit), in order to minimize ground surface settlement, the pipe-roof method was employed as an auxiliary measure when removing the portion between two parallel shield tunnels to form one large tunnel for the station. 14 steel pipes (dia.1,219.2mm, length 75m) were driven in horizontally so as to cover tunnels and support heavy and extremely soft covering soil and surface structures. Procedures of temporary supporting, excavation under compressed air, reinforcing, concreting, etc., and some comparisons with conventional methods are described.

Jan 1, 1979

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By Zeni J. T

Gold was mined from quartz bodies at Ballarat East from the 1850s until closure of the last mine in 1917. The average depth of mines was about 350 m.Ballarat Goldfields Limited (BGL) carried out diamond drilling from surface between 1985 and 1987 which proved the continuation of gold-quartz mineralisation beneath the old mines.During 1989 an underground development program was commenced to access the mineralisation for detailed exploration. The program included two simultaneous shaft developments. These were known as B2 shaft and Llanberris No.1 shaft.

Jan 1, 1992

By Jesús Valdivia, Enrique Garay

El proyecto Shalipayco cuenta con 20 Mt @ 5.6% Zn, 0.5% Pb, y 1.3 oz/t Ag en recursos totales (M+I+I) a la fecha, consolidando por lo tanto uno de los más grande recursos inexplotados de mineralización de Zn-Pb-Ag tipo Mississippi Valley (MVT) en Perú. La dolomitización es una alteración que está asociada a los mantos mineralizados de Shalipayco y sirve como guía prospectivo. Cercana del depósito ubicase horizontes evaporíticos y brechas de colapso, que también pueden significar controles importantes para mineralizaciones MVT.

May 1, 2008

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

By David G. Chedgy, Edward A. Zawadzki, Robert D. Stoessner

Extensive research and testing in commercial facilities has clearly demonstrated that heavy medium cyclones are the most effective process for cleaning a 0.6 x 0.15mm (28 x 100 Mesh) coal at low separating gravities, less than 1.35. This paper describes testing performed to deter- mine system characteristics at these lower gravities and the type of circuitry required to maximize performance. The results of these studies include both pilot and commercial scale tests of cleaning 0.6 x 015mm (28 x100M) coal.

Jan 1, 1988

LIMA (PERU) Established May, 1952 James S Young, Honorary Member of Section (Legion of Honor Member) Bernard T Colley, Honorary Member of Section (Legion of Honor Member) Edward H Robie, Honorary Member of Section (Secretary of AIME) Carl W Westphal, Chairman Ernesto A Baertl, 1st Vice-Chairman Pierre L Garrigue, 2nd Vice-Chairman Walter E King, Secretary-Treasurer Avenida Santa Cruz 331 San Isidro, Lima, Peru Daniel M Rodriguez, Assistant Secretary Alberto E Brazzini, Assistant Treasurer Robert P Koenig, Section Delegate Irving L Barker, Special Representative

Jan 1, 1954

By G. M. Thain

Ancient Mining - The following three contributions were received for publication in addition to the preceding papers. 1. Ancient gold-mining sites in the Transvaal G. M. THAIN* Pre-European gold mining and working in South Africa is a tantalizing field for conjecture. Well over thousand sites have been identified in Rhodesia, but here we have had to reach double figures, judging by published accounts. Geologically, the Transvaal is less amenable primitive exploitation, but it difficult to reject the idea that the knowledge gained to the north did not have its influence south of the Limpopo.

Jan 1, 1974

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

By W. K. Hartley

INTRODUCTION AND HISTORY The Kimberley Division of De Beers Consolidated Mines Limited includes four underground mines in Kimberley viz. Dutoitspan, Bultfontein, De Beers and Wesselton Mine and two outside mines, viz. Finsch, an opencast operation and Koffie- fontein, an underground operation. Figure 1 is a map of the Kimberley district showing the location of these mines. Finsch is 150km west of Kimberley and Koffiefontein is 80km south of Kimberley. The head office of the De Beers Company is in Kimberley. The diamond sorting and trading companies for diamonds produced in South Africa are also in Kimberley. Diamonds were first discovered in the Kimberley area at Hopetown in 1866 on the banks of the Orange River. This, and later finds, triggered the start of the great "Diamond Rush". In 1870 the Jagersfontein (now closed) and Dutoitspan pipes were discovered, followed by those at Bultfontein, De Beers and Kimberley Mine (now closed) in 1871, Koffiefontein in 1880 and Wesselton in 1891. Finsch Mine was a more recent discovery in 1961. Finsch, due to go underground in 1986, and Koffiefontein, are fully self-contained with their own treatment plants, housing, services etc. The four Kimberley mines deliver ore by conveyor to a central treatment plant and use joint ser- vices. ,+lining is presently carried out mainly by Block Caving which has replaced the earlier Chambering method. De Beers Mine, on a limited scale, and Wesselton Mine have recently started to use Sub-Level Caving, and both Bultfontein and Du- toitspan are scheduled to use the same method at a later date. The combined ore tonnage produced by the Kimberley Mines is 17 400 tons per day, Koffiefontein 12 000 tons per day and Finsch Mine 17 000 tons per day. THE EVOLUTION OF MINING METHODS Initially, the open-cast mining was carried out to as great a depth as safety would permit. In the early stages of open-cast mining, the Kimberlite was removed in horizontal slices from levels 13m to 20m apart. The rock broken in the workings was raised to the surface by means of endless rope haulage inclines. As lower levels were attained these rope haulages were replaced by aerial hoists, inclined shaft haulages or inclined skip-ways. These methods were dependent upon the strength of the unsupported pipe walls, which became increasingly unstable with depth and a system was adopted whereby the ground mined in open excavations was tipped down passes to tunnels connecting with vertical hoisting shafts sunk in the country rock. As work in the open pit became more and more impracticable due to extensive falls of ground, this system was replaced by a combination of open-cast and underground mining, and eventually by wholly underground methods. Chambering With the advent of underground mining, a system known as "Chambering" (or "Inclined Chambering") was evolved. It was essentially a combination of shrinkage stoping and caving, whereby advantage was taken of the high pressure exerted by the loose rock that had accumulated in the open excavations due to the collapse of the pipe walls. This mining method was introduced around 1890 and was successfully employed, with little change, up to the early nineteen seventies. In this system each mine was served by a main hoisting shaft situated about 300m in the country rock. Main haulage cross cuts were driven from the shaft to the pipe at 200m (600ft) vertical intervals. A sub-vertical shaft, situated close to the pipe provided access to the working levels. Chamber levels were established from the sub-vertical shaft at 13m (40ft) intervals. See figure 2. On each of these levels successive 6,8m wide “cuts" were mined out across the pipe, from one rock contact to the other, and extended vertically to the footwall of the level above. Every 6,8m cut was made up of a chamber and a "back-pillart1, each approximately 3,401 wide. The chamber was mined by overhand shrinkage stoping. The levels were carried "en echelon", with each chamber on a level approximately three cuts ahead of the chamber on the level

Jan 1, 1981

By Edward Judd

CANADA'S mining industry is rapidly recovering from the depression through which it passed in 1921. Its total output of $183,029,600 in 1922 was 6.4 per cent. greater than that of 1921, and was exceeded by only three previous years, 1917, 1918, and 1920. Table 1 compares the output of a few of 'the more important items selected from preliminary data published' by the Dominion Bureau of Statistics. TABLE 1.-OUTPUT OF CERTAIN MINERAL PRODUCTS IN CANADA PER CENT. 1921 1922 CHANGE Cobalt, metal and in compounds, lb 252,000 443,800 +76.1; Copper contents of blister, matte, and exported ores, lb 47,620,820 43,321,400 - 9.0 Refined copper, lb 4,286,000 730,000 -83.0 Gold, fine oz 926,329 1,230,985 +32.8 Pig iron, sh. tons 665,676 429,024 -35.5 Lead, sh. tons 33,340 47,085 +41.2 Nickel contents of matte, etc., lb. 19,293,060 17,496,490 - 9.3 Silver, including that in base bullion, gold bullion, etc., fine, oz. 13,543,198 17,611,646 +30.0 Zinc (nearly all refined), sh. tons. 26,545 28,199 + 6.2 Asbestos shipments, sh. tons 92,761 136,657 +47.3 Coal, all grades, sh. tons 15,057,500 15,045,300 Gypsum shipments, sh. tons 386,550 441,160 +14.1 Natural gas, M. cu. ft 14,077,600 14,954,100 + 6.2 Petroleum, bbl : 187,540 178,570 - 4.8 Cement, bbl 5,752,885 6,943,968 +21.0 Brick, structural, all kinds, M. , , 109,009 127,137 +17.0 On the basis of estimated market values, the whole output of 1922 was contributed as follows: Metals, 33.4 per cent.; non-metallic minerals, 45.1 per cent.; structural materials and clay products, 21.5 percent.; this distribution indicates a return of the metal mining. industry nearly to the position of relative importance that it occupied. before 1921, in which year metals contributed only 28.7 per cent. to the total value. of output while non-metallics gave 51.1 per cent. Canadian cobalt originates entirely in the ores of the Cobalt district, which are mainly treated at smelters in southern Ontario, although some quantities of residues have been exported to England and Europe. Exports during 1922 increased even more than production, consisting of about four-fifths . cobalt oxides and salts, and one-fifth of cobalt alloys and other metal combinations.

Jan 8, 1923

By Chris L. Powell, Russell J. Denny.

"The remotely located Cockatoo Island iron ore mine off the Kimberly coast in Western Australia, which has been in operation since 1951, was recently expanded up to 50m below sea-level using staged construction of a rock-filled seawall around the open cut mining operation. The most recent stage of the seawall expansion required a seepage reducing cut-off barrier to be installed through the seawall into underlying seabed sediments. A line of grout holes at 1m centres was proposed to form the seepage barrier, with grouting extending 17m below the top of the seawall. Top hammer drilling techniques were used to penetrate the 12m deep rockfill to seabed level, and permeation grouting carried out within the rockfill to fill voids and stabilise material around grout holes. The local 10m tides meant that tidal washout of fines and grout would be a major risk, and so a combination of cementitious and chemical grout was used to create rapid gel times. Following permeation grouting, holes were re-opened to allow jet grouting to hydraulically mix and grout permeable seabed sediments below the seawall. Using the duplex jet grout system in a single pass to 17m below platform level, the jet grouting was extended upwards into the seawall fill itself to overlap with the earlier permeation grouting. Finally a soil/cement mixed capping trench was installed using slurry trenching techniques with soil/cement/bentonite mixed backfill in order to complete the grout treatment. The approach taken allowed considerable onsite flexibility in technique. An automated slurry batching plant allowed adjustment of mixes to suit the varying subsurface conditions which were encountered during the works.IntroductionLate in 2013 Wagstaff Piling was engaged to install a seepage barrier through a rockfilled seawall built to allow expansion of sub-sea iron ore mining operations on Cockatoo Island off the remote Kimberley coast in the North West of Western Australia. Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of sub-sea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansion stages that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative grout curtain seepage barrier solution was selected to ultimately provide the necessary cut-off to allow access to high grade ore, while protecting the mine from inundation by the sea."

Jan 1, 2016

By A. Mitchell, T. Bagshaw

A recent paper by Thomas1 has presented new data on the solubility of hydrogen in solid silver at 1 atm pressure in the temperature range 600° to 963°C. However, no data is reported in the literature on hydrogen solubility in liquid silver. The Sieverts technique which has been described previously2,3 was used in the present work. Charges of approximately 160 g were melted in Morgan "purox" recrystallized alumina crucibles and purified helium was used for the determination of the "hot volume" during each experiment. A chemical analysis of the silver indicates that the impurity content (Cu + Al) is less than 0.02 wt pct. Hydrogen solubility in the temperature range 963° to 1200°C was investigated. The results of three experiments are shown in Table I. Fig. 1 shows an Arrhenius plot of the present work together with the solid-state data of Thomas, Steacie, and johnson,4 Eichenauer et al.,5 and Siegelin et al.6 The following expression has been derived from the Arrhenius plot of the present data: log (solubility of hydrogen, cm3 per 100 g) = 2.154-3512.0/ToK The heat of solution derived from Fig. 1 is 31,150 cal per g mole H2 compared with the value of 33,020 cal per g mole H2 obtained by Thomas and 12,000 cal per g mole H2 obtained from the data of Steacie. It was observed that hydrogen evolution took place when the silver melts were solidified under 1 atm of hydrogen, which would not be expected from an extrapolation of the results of Steacie. Schenck and Lange7 have observed that, for several transition metals at their melting points, the ratio of the hydrogen solubility in the liquid to that in the solid lies in the range 2.1 to 3.1. The present results and those of Thomas are in accord in this respect having a ratio of 2.8. 'C. L. Thomas: Trans. TMS-AIME, 1967 vol. 239, pp. 485-96. 2T. Bagshaw and A. Mitchell: I. Iron Steel Inst., 1966, vol. 204, p. 87. 'M. Weinstein and J. F. Elliott: Trans. TWS-AIME, 1963, vol. 227, p. 382. 'E. W. R. Steacie and F. M. G. Johnson: Proc. Roy. Soc. (London), Ser. A, 1928, vol. 117, pp. 662-79. 'W. Eichenauer et al.: Z. Metallk., 1958, vol. 49, pp. 220-25. 6W. Siegelin et al.: Z. Elektrochem., 1957, vol. 61, pp. 359-66. 'H. Schenck and K. W. Lange: Arch Eisenhuettenw., 1966, vol. 37, no. 9, pp. 739-48.

Jan 1, 1969

By John C. Gould

GENERAL DESCRIPTION The Climax mine is located 161 km (100 miles) southwest of Denver on Fremont Pass astride the Con¬tinental Divide. Climax employs 2800 people to pro¬duce 42 670 t/d (47,000 stpd) of molybdenum ore. The Storke level, the main underground level, produces 19 970 t/d (22,000 stpd); the 600 level, the lowest ac¬tive underground area, produces 7260 t/d (8000 stpd); and the open pit presently produces 15 430 t/d (17,000 stpd), Fig. 1. A panel caving method is possible because of the favorable geology and geometry of the Climax ore body. Geology The Climax deposit is composed of three separate ore bodies formed in a massive Tertiary stockwork which penetrates Precambrian granites and schists. The ore bodies are elliptical in plan with overall dimensions of 914 x 1219 m (3000 x 4000 ft). In section the ore bodies are arcuate with an overall height of 457 m (1500 ft), although the depth is not firmly ascertained. Ore grade decreases rapidly into a highly siliceous cen¬tral core and more gradually toward the outer bounda¬ries of the deposit. The mineralization is relatively continuous in the ore zone and contains few dilution-causing waste inclusions. Molybdenite is contained in pre-ore fractures which were largely recemented during the three mineralization pulses. Postore fractures, with a spacing of a few inches to several meters (feet), render the deposit amenable to caving when it is undercut. The peripheral rock caves similarly to the ore, but the central core is competent and is difficult to cave. Caving Feasibility Successful caving action requires an undercut area of approximately 122 by 122 m (400 by 400 ft). When the undercut area exceeds this minimum distance, the arching effect is lost, and the ore column collapses. Ore extensions from the main cave area less than 122 m (400 ft) wide usually cannot be caved. Waste or low¬grade areas within the deposit can be left if they are large enough to carry weight around openings passing through them. Experience indicates that these areas should be over 30 m (100 ft) in length and width. Smaller unprofitable units of waste, such as postore dikes, are mined to avoid weight problems and result in ore dilution. Successful caving and ore recovery are dependent upon timely ore removal from the undercut zone because columns of immobile ore inhibit caving and concentrate weight onto the underlying workings. Climax experience indicates that a finger (drawpoint) spacing* averaging 10.4 m (34 ft) yields an excellent caving action and a 92.5% ore recovery at the estimated grade. An additional 15% of the ore is recovered-at a diluted grade (Fig. 2). Mine Layout The slusher drift is the primary production facility (Fig. 3). The ore is undercut and caved into the fingers,

Jan 1, 1982

"The richest hill on earth" had its start as a placer gold camp in 1864. The gold was quickly worked out but then silver was discovered in the copper ores in Butte Hill. After ten years as a silver camp, rich copper ore was found in 1881 and the future of Butte was assured. In the early 1960's, the Anaconda Company began the shift from underground mining at Butte to open pit mining of the enormous, low-grade copper deposit surrounding the old high-grade veins which had been worked for over eighty years. Their first primary crusher was a 66 in. by 84 in. (168 m by 2. 13 m) jaw crusher. The pit was expanded at such a rate, however, that its location became endangered. Additionally, the new Clyde Weed concentrator had been built at Butte; and in 1969 construction of a new gyratory installation was started. The primary crusher at the Clyde Weed concentrator is one of the most unusual primary crushers ever put into operation. At times, the ore from the Berkeley pit contains large amounts of timber, pipe, rails, and so forth left in the ore body from the old underground mining operations; and the crusher installation had to be designed so this tramp material could be readily removed ahead of the crusher. Ore is delivered by 100- and 150-ton trucks to two side-by-side dump pockets, each with a capacity of 400 tons. Originally, a hydraulic grapple was installed on the dividing wall between the dump pockets; but it was found that oversize boulders large enough to block the discharge opening at the bottom of each hopper were rapidly covered with other material, and the grapple was unable to reach and remove the large boulders causing the blockage. In addition, the grapple was located in a quite vulnerable position; and it sustained damage from being struck by rock dumped from the trucks. Oversize boulders are now blasted. Underneath each pocket is a vibrating grizzly feeder with the grizzly bars set at 4 in. (102 mm). These feeder-grizzlies are 84 in. (2. 13 m) wide and 32 .ft (9. 75 m) long, with grizzly sections 16 ft (4. 88 m) long. Approximately 75% of the ore passes through the grizzlies and grizzly oversize then drops onto two parallel 6 ft (1. 83 m) wide picking belts. The belts are 3 in. (76 mm) thick and rest on idlers supported by air- filled rubber shock absorbers. At the side of each picking belt is a hydraulic grapple which is used to remove timbers too large to be removed by hand. At times, four men are used to remove timber and tramp iron. Timbers are dropped onto a transverse belt conveyor which discharges into a truck stationed outside the primary crusher building,

Jan 1, 1978

By Ursula E. Wolff

The precipitation of carbides from an alloy containing 33 pct Ni, 21 pct Cr, balance iron, was investigated electron microscopically by means of extraction replicas and thinned metal foils. Annealing temperatures ranged from 565°to 870°C and up to several thousand hours. M23C6 precipitated in pain boundaries, incoherent and coherent twin boundaries in that sequence. The orientation relationship between carbides and austenite matrix was determined and correlated with the morphology of the carbides and with the type of boundary in which precipitation occurred. In large-angle grain boundaries, as well as in coherent twin boundaries, the carbides had the same orientation as one of the adjacent pains. These carbides formed sheets of individual flakes with shapes related to the orientation of the boundary. In incoherent twin boundaries carbides precipitated in ribbons composed of pavallel rods. An unidentified subcarbide was found to precede precipitation of M23C6 in these boundaries. The M 23 C6 rods had a kind of fiber texture with (110) parallel to the long dimension of the rods and ribbon, and with orientations of both of the adjacent twin-related austenite crystals Predominant in the texture of the carbide. A hard sphere crystal model has been used to discuss orientation and morphology of the carbides in terms of free volume and vacancies available in the boundaries. A number of papers have dealt with the morphology of chromium carbide (M23 C6) precipitated in austenitic stainless steels.1"7 In all these investigations, the carbides were examined in the electron microscope by means of extraction replicas. With this technique, the carbides retain the spatial distribution they had in the bulk sample. However, since the matrix is dissolved in the process, the particles can turn in an unpredictable way; and the orientation relationship between matrix and carbides cannot be established. In this paper the results of studies on extraction replicas and on thinned metal foils are reported. These studies were undertaken to determine the matrix-to-car bide orientation relationship, and to correlate the orientation of the carbides with their morphology. PROCEDURE The material used was an austenitic alloy with 33 pct Ni, 21 pct Cr, balance iron, containing approximately 0.05 pct C. Coupons of 1.25-mm sheet were first solution-annealed at 1050°C for 15 min and air-cooled. Then, to precipitate the carbides, samples were isothermally annealed in the range from 565" to 870°C for times up to several thousand hours. All further specimen-preparation procedures were carried out after the final anneal. Carbon extraction replicas from polished and etched surfaces were made with 10 pct bromine in methyl alcohol.' Thin foils were prepared from punched-out 3-mm-diam disksg which fit into the electron-microscope holder. The disks were prethinned by grinding to approximately 0.5 mm thickness, and then electro-polished in a polytetrafluoroethylene holder1' with a solution containing 5 pct perchloric acid in acetic acid to which 10 g per 1 Cro3 and 5 g per 1 nickel chloride were added (etchant modified from that of Briers et al."). This solution dissolves neither the carbides nor the austenite around the carbides preferentially. By using extraction replicas, electron micrographs and selected-area electron-diffraction patterns were taken from the same carbide arrays. By using thin foils, electron micrographs were made from a grain boundary area containing carbides. Electron-diffraction patterns were then taken from the same area and from each of the adjacent grains separately. In this manner, the orientation of each grain could be determined without interference by the carbide pattern. A peculiarity of extraction replicas should be pointed out. After the matrix is etched away, the carbide arrays float freely in the etching and washing solutions, and are held in place only at the anchoring points in the carbon replica. When the replica is picked up with a screen the carbide arrays tend to flip to one side. Thus, while the surface features are preserved, the original arrangement of the carbides may severely and unpredictably be disturbed whenever the specimen contains large amounts of interconnected carbides. Nevertheless, it is possible to correlate the different morphologies of the carbides with the type of boundary in which they have precipitated. RESULTS 1) Extraction Replicas. Fig. 1 shows that the grain boundaries usually are curved, multicornered surfaces of random orientation. The coherent twin boundaries (which are (111) planes) cut a grain into parallel slices. Incoherent twin boundaries occur at the ends and on the steps of twins and are often narrow, parallel-sided strips which are much longer than they are wide. Different morphologies can clearly be distinguished for the M23Ce carbides precipitated in each of these types of boundaries, and agree well with those observed by kinzel.2 The kinetics of this precipitation has been investigated." The first carbides precipitate in junctions of three grain boundaries and fan out from there into the adjoining boundary surfaces, Fig. 2(a). These carbides are oriented randomly, Fig. 2(b), and become coarser and thicker as annealing time increases. The large-angle grain boundaries are next to fill

Jan 1, 1967

By OÆShea P. J, Dickson T. W

In April 1994 the Victorian Premier announced new State initiatives, collectively termed the Victorian Initiative for Minerals and Petroleum (VIMP), for exploration totalling $16.5 m over three years. The program, initially centred on the northwest of Victoria, the Eastern Highlands and the Otway Basin, is due for completion in June 1997 and has been designed to attract explorers to highly prospective but currently under-explored parts of the State. Major components of the program include acquisition of geophysical data (including airborne magnetics and radiometrics, gravity and seismic data), stratigraphic drilling, geological mapping and mineral resource data compilation. At the completion of the current program, 70 per cent of the State will have been covered by airborne magnetic and radiometric coverage at 400 m line spacing or better (Figure I) while 20 per cent of the State will have been covered by new geological mapping. The completion of database compilations for geochemistry, mine data and exploration licence summaries during the VIMP program is shown in Figure 2. The new airborne geophysical surveys have been flown partly under the VIMP program and partly by AGSO under the National Geoscience Mapping Accord (NGMA). Data from these surveys have been interpreted and incorporated into the geological mapping in order to enhance the quality of map products, especially in areas of Cainozoic cover. The first series 1:250 000 scale geological map coverage of Victoria was completed by the Geological Survey of Victoria (GSV) in 1977, and was based on compilation of historical geological mapping with minor field checking in most cases. The first metric 1:50 000 scale geology maps were also commenced in the 1970s, but were discontinued in the 1980s in favour of 1:100 000 scale map production. Driven by customer survey findings and with the benefit of detailed airborne geophysical data in the 1990s, the GSV reverted to 1:50 000 scale map production in 1995, with 1:10 000 scale maps made in areas of significant gold production. Geological reports still cover standard 1:100 000 scale map areas, but are now accompanied by four 1:50 000 scale maps. These new series 1:50 000 scale geological maps have been supported by comprehensive mine data and exploration licence summary databases in addition to the new geophysics, and benefit from the advances made in structural geological interpretation over the last decade. The new phase of geological mapping in Victoria, commenced under the NGMA in 1990 and accelerated under VIMP in 1994, has been focused in the central Victorian goldfields and eastern Highlands areas of the State (Figure 1). Results to-date have led to a number of major advances in the understanding of the eeoloeical evolution of Victoria.

Jan 1, 1997