Search Documents

By J. Herman

The Mid-Continent Geophysical Anomaly (M.G.A.) which extends from Michigan into Wisconsin, Minnesota, Iowa, Nebraska, and Kansas, has recently been the object of intense preliminary oil and gas exploration activity involving widespread land leasing, seismic data collection, permitting of deep exploratory holes and other activities (Paul et al., 1985). This report describes the remote-sensing techniques and results of the application of these techniques to study the geology of the M.G.A. and the surroundings in Iowa. In early 1981, Coal Valley Natural Resources contracted Geospectra Corporation to find a large, (100,000 acres or larger) lease block for wildcat oil and gas exploration. The southwest Iowa area was chosen for several reasons. First, southwest Iowa contains the northeast portion of the Forest City basin (Figure 1) which has produced oil and gas from numerous fields in Kansas, Missouri, and Nebraska (Landes, 1970; Petzet, 1982).

Jan 1, 1986

By Andrew Chegwidden, Tara Wilk

Construction of Shaft 17B-1, a part of The New York City water supply system, required an excavation of approximately 38 m (123 ft) through water-bearing overburden soil and more than 152 m (500 ft) of gneiss bedrock to make a connection to Water Tunnel No. 3. Ground freezing was the specified method to provide temporary earth support and ground water control for the overburden material. The ground freezing process relied on a supplemental geotechnical investigation and comprehensive laboratory testing of the frozen soil to evaluate the potential long-term creep behavior of the soil and the elimination of a temporary lining system. This paper describes that process as well as the drilling and installation methods of the ground freezing system. Additionally, the methodical system of excavation and insulation is discussed that permitted a safe and timely excavation followed by the installation of the permanent concrete liner.

Jun 13, 2023

By V. Galla

In the present paper, two large diameter columns 2 m tall and 1.3 m diameter filled with crushed (finer) and run off mine (coarser) heap leach materials respectively were used to perform unsaturated flow studies. Instruments measuring moisture content and matric suction were placed in the columns at different depths as water was applied at calibrated flow rates from the top of the columns. The outflows from the columns were recorded using tipping bucket rain gauge placed at the bottom of the columns. Unsaturated hydraulic parameters were also obtained for the heap leach materials, scalped (passing 4.75 mm sieve size) and whole (passing 37.5 mm sieve size) sample. The measurements obtained from the columns were later compared with unsaturated flow modeling results. The comparison indicated sensitivity towards the sample size selection for unsaturated hydraulic parameters, and initial conditions considered in the model.

Jan 1, 2009

By Mark R. Rybak, James Delmonte, Travis Hartman

The City of Phoenix, Arizona designed a 7.2 km (4.5 mi) long water transmission main from the South Mountain Reservoir to the Ahwatukee Foothills Reservoir to address the growing demand for drinking water in the southeast valley. The pipeline design called for a bored tunnel in a very environmentally sensitive area. The Reach3B contract included an 2.44 m (8 ft) diameter TBM excavated tunnel, 1,847 m(6,060 ft) in length. The geotechnical investigation revealed that the tunnel would likely pass through zones of loose to moderately cemented soils (caliche). The primary tunnel support would consist of rock bolts, circular steel ribs, hard wood lagging, and mine straps. A TBM that could handle the ground conditions and allow for efficient ground support installation was required. This paper describes the construction of a small diameter rock tunnel in challenging ground conditions.

Jan 1, 2003

By Hendri Silaen, Charles Leatemia, Monang Napitupulu, John Kamarea, Arwin Edijanto, Riza Hasan, Avesiena Primadiansyah

The Deep Mill Level Zone (DMLZ) is the fourth panel cave mine in the East Ertsberg Skarn System, (EESS) which lies 500 m below the producing Deep Ore Zone (DOZ) mine and up to 1,700 m below the surface. The interaction between the DMLZ and DOZ is occurring as the DMLZ cave grows vertically toward the DOZ footprint. During this process, a rapid change in the global mine system stress is anticipated. This change is forecasted to drive substantial changes in the magnitude and direction of principal stresses in the DMLZ and DOZ mines at PT Freeport Indonesia. These changes will bring the mine system closer to the ultimate capacity of the excavations and can result in significant impacts to mine stability if not managed. Critical to this management, is understanding cave growth and locations, as well as how these changes will impact stress conditions.

Apr 26, 2022

By R. Padilla

The reaction of chalcopyrite with gaseous sulfur has been investigated in the range 350-450 °C in order to transform this mineral into a more acid soluble copper sulfide and insoluble iron sulfide. The results of thermodynamic analysis of this system as well as the X-ray diffraction analysis of the reaction products showed that in the temperature range 350 400°C the sulfidation reaction proceeded without formation of intermediate copper-iron sulfides according to: The effects of temperature and time on the conversion of chalcopyrite were studied. Conversion of chalcopyrite reached about 80% very rapidly with increase in temperature up to about 400°C. The recovery of copper from the sulfidized samples was determined by leaching in oxygenated 1.2M H2S04, 2M NaCI solution. Copper recoveries over 90 % were obtained from samples sulfidized for 30 min at temperatures lower than 400°C.

Jan 1, 2001

By M C. Ackland

The Grande Côte Mineral Sands Deposit (GCMSP) is located on a coastal mobile dune system in Senegal on the west coast of Africa. Senegal is a stable, democratic republic, having gained its independence from France in 1960. It has a population of about 12.5 million people. The dunes begin about 25 km north-east of Dakar, the capital city of Senegal, and extend northwards for more than 140 km. The mineralised dune system averages about 2 km wide with some areas extending to up to 4.5 km wide.Mineral Deposits limited (MDL), a Melbourne-based company with over 60 years operational experience in mineral sand mining in Australia, holds, through its Senegalese subsidiary MDL Senegal SARL (MDLS), a 25-year Mining Concession covering the deposits. The main heavy mineral (HM) areas identified to date are, from south to north, Mboro, Fass Boye, Diogo and Lompoul. Within the Mining Concession there is potential to identify additional resources beyond the limits of present drilling. The dunes are mobile or semi fixed, pale yellow in colour and overlie older white marine sands. The dunes range between 5 m and 30 m in height and the mineralised zones, which are essentially flat-lying, average around 15 m in thickness. The mineralisation consists, principally of ilmenite with accessory zircon, rutile and leucoxene. Zircon and ilmenite are the main commodities of interest.Independent consultants AMC estimated mineral resources for the four main deposits in 2006 of 1330 Mt of sand averaging 2.0 per cent HM at a cut-off grade of 1.5 per cent HM. At a cut-off grade of one per cent the resources were 3200 Mt averaging 1.5 per cent HM. All of the estimate was classified as Inferred Resources under the 2004 Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC, 2004).Subsequent completion of infill drilling, sampling and assaying of the initial mining area, centred at Diogo, was completed in 2008, enabling a final dredge path to be designed and ore reserves estimated, based on a JORC compliant Measured and Indicated Mineral Resource. Infill drilling is continuing in the Lompoul and the results of this campaign will be included in the JORC compliant data base by AMC in April 2010 to enable the 15 per cent year dredge path and mine plan to be finalised.Development studies have shown that the project can be optimised as a dredging operation, with mineralised sand being treated in a conventional floating spiral preconcentrator, wet concentrator and dry mineral separation plant. Engineering work now substantially completed by Ausenco Limited (Ausenco) has developed the combination of some existing plant from MDL’s past operations, and new plant for the complete process from dredging to final product separation and grading. Testwork on a series of bulk samples has determined that the project can yield a high quality zircon product and an ilmenite product along with minor rutile and leucoxene.Work to date indicates a likely output of around 80 000 t of zircon in various quality streams (Primary, Secondary, Standard and Foundry Grades), around 550 000 t of ilmenite plus around 15000 t of rutile and around 12 000 t of leucoxene/secondary ilmenite. Planned zircon output would represent around 7per cent of the total world production, which would make the GCZ&IP a significant producer on a world scale.The studies have indicated capital costs to be in the range of US$400 M total operating cost (after completion of ramp-up) of around US$50 M - $55 M/a. Revenue is expected to be in the range $127 M - $157 M/a.

Oct 5, 2011

By Ueki S

Underground coal gasification (UCG) is a promising process for obtai- ning energy from coal, which is either unmineable with current mining techno- logy or uneconomic to recover, using conventional methods, in the present energy market situation. There are several coal fields, which could become new coal reserves, if the UCG process were successfully applied. In the 1960's Japanese researchers made a number of basic studies and field tests into UCG, although not all of them produced favourable results. This paper reviews Japanese research on UCG. This includs basic studies into coal gasification using a small, tube reactor fed by air and oxygen, and also large scale model stu- dies(reactor size of 8.Om x 2.4m x 1.5 m). Field test results from Akabira colliery in Hokkaido and a feasibility study of power generation using UCG from a coal field in Hokkaido are also Presented.

Jan 1, 1987

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Y. Z. Wang

Zhengzhou Yellow River Highway Bridge, which is under construction, has a total length of 5550 meters with bored cast-in-place concrete piles as the foundations of its piers which have a diameter of 2.20 m with a length of approximately 65 m. This paper attempts, through the introduction of the said bridge's footing pile design and construction, mainly to give an account of the following points: 1) experiment and research on deep friction pile with a large diameter, 2) calculation of vertical carrying capacity of the pile with a large diameter, 3) analy­sis of horizontal forces the footing-piles of the column-shaped piers, 4) application of normal and reverse-circulation rotary drilling technologies to the construction of bored cast-in-place concrete piles with a large diameter and 5) applying super-sonic impulse on destruction detective device to examine the quality of the pile concrete.

Jan 1, 2010

By Mowat B. A

I lamata is within the Morobe Goldfield (7¦ 25' S, 146¦ 39' E) on the Wau (SB 55-14),1:250,000 scale map sheet (Fig 1). The deposit is 13 km SW of Wau, within the headwaters of the Upper Watut River, at an average elevation of 2000 m. The steep mountainous terrain is covered by dense tropical rainforest and access is by helicopter or by foot track. The deposit has been described previously by Wells and Young (1991) and 1)enwer. Leach and Mowat (1995). Data collected to late 1996 have been used to estimate an Inferred Resource of 9.2 Mt at 3.1 g/t gold using a cutoff of 0.5 g/t. This contains a high grade portion for which an Inferred Resource of 1.2 Mt at 9.7 grt gold has been estimated using a 5.0 g/t cutoff.

Jan 1, 1997

By Bratt G. C, Horsham T. R, Langlois D. R

Mercury is precipitated from weakly acidic sulphuric acid plant waste liquor at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited. Factors determining the choice of process and reagent, as well as details of process development including scale- up, and the time scale of implementation are outlined. The plant is designed for a maximum flow of 120 m3/h.of liquor containing mercury and saturated with sulphur dioxide. Mercury is precipitated by fluidised beds of aluminium pellets contained in lead columns. Liquor is then clarified with plate and frame presses. Experimental work on the mercury precip- itation reaction was conducted in three phases involving a scale-up of 100 times in equipment size. Extensive pilot filtration work was carried out on a 1 m2 press. Scale-up of 120 times was required for specification of plant filters. The basis of scale-up is outlined.

Jan 1, 1977

By A. Partos

It was decided to build a fourteen-storied office building over a six-storied garage and a four-storied office building. The high vertical and horizontal loads required foundations on rock approximately 18m below street level. Drilled piers (caissons) were selected. Eight caissons (1.98m diameter) were installed through the six-storied garage and four caissons from a temporary deck at the location of a former two-storied building. Excavations were done by the slurry method. Proof testing of rock was done before construction by test borings and during construction with a core barrel of small diameter. Quality control measures included telecommunications between ground crews and the equipment operator on the garage roof; records of field observations and testing of bentonite slurry and rock; and a continuous evaluation of all information. Instruments were installed in one caisson to monitor load distributions and curing of concrete.

Jan 1, 2010

By B. M. Wainstein

An extension of lognormal theory and its application to risk analysis models for new mining ventures by B. M. WAINSTEIN*, B.Sc., M.B.A. (Witwatersrand) (Visitor) The lognormal distribution, which remains the most popular distribution model for ore values, is investigated. The T-distribution, an integral part of this theory, is dependent on the sample size, n, and the unknown population parameter, o2, which cannot be integrated out. Hence, o2constitutes a nuisance parameter. In this study, the robustness of the T-distribution to changes in o2 is examined. It is found that the T-distribution is robust for 0,1 <= o2 >= 2,5, a domain covering most practical applications of the lognormal theory. By the use of o2 = 0,7, multiplier factors, which facilitate the computation of the confidence limits, are derived for a comprehensive set of confidence levels.

Jan 4, 1975

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By Timothy N. Dunne, Joseph M. Gonzalez

This paper presents the case history of a comprehensive geotechnical investigation for the Crosstown Transport Facility, a 10,880 m long, 3.2 m diameter pressure tunnel proposed for construction in San Francisco, California. The proposed tunnel would be part of the City and County of San Francisco&apos;s Clean Water Program, and its purpose would be to convey stormwater and sewage from the east side of the City to the Pacific Ocean. Tunneling conditions were defined by surface geologic mapping, 94 exploratory borings, surface and borehole geophysics, aquifer testing, Goodman Jack testing, pressuremeter testing, and laboratory testing. Through the use of advanced coring techniques and a strictly controlled drilling fluid system, core recovery averaged 90 percent in the sheared and fractured rock of the Franciscan Formation. As a result, over 1,400 linear meters of rock core was recovered and is available for examination.

Jan 1, 1983

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

1. New books from The Institute of Metals Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00.High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45.Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15.Marine engineering with copper-nickel. 1988. 103 pp. £18.Sir Henry Bessemer: An autobiography. 1989.380 pp. £16.95. 2. Other publishers Occupational safety and accident prevention. Behavioural strategies and methods, by C.G. Hoyos and B.M. Zimolong. Amsterdam, Elsevier, 1988. 218 pp. Dfl. 180.00. Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95.

Jan 1, 1989

By Takefumi Takuma, Masashi Nagano, Koji Kajino

As part of the construction of a multi-span pre-stressed concrete girder bridge for Japan’s new high speed rail line, landslide preventive piles were installed on the flank of a steep slope. The rotary pressin piling method was selected to install three parallel rows of long (up to 36m, i.e., 118ft) and large diameter (1,200mm, i.e., 47.2in) pipe piles safely into the slope as a deterrent measure. They were spaced at 2.5 Dia (3.0m, i.e., 9.8ft) on center and were staggered to allow the groundwater to migrate between the piles. Each pile had a sacrificial cutting shoe welded at its toe for speedy installation and was rotated and simultaneously pressed into soil on the slope through the stable bedrock thereunder to achieve a robust landslide prevention in a relatively short period of time.