Search Documents

By Mark Flower

A 20L ignition test chamber has been used to test suspensions of 7 UK and world traded coals in air and O2/CO2 mixtures typical of oxy-combustion conditions. The coals varied in rank from sub-bituminous to bituminous and were tested in varying concentrations from the ignition limit to 400g/m3. Following each successful test the combustion residue was collected, weighed and analysed within a thermogravimetric analyser, allowing Q factors to be estimated. The ignition limit varied slightly in air, but was mostly around the 200g/m3 level. With the exception of Coal C, which was much harder to ignite, it correlated roughly with coal rank. The ignition limit changed significantly with O2 concentration when in mixed O2/CO2 gases. Only a few high volatile coals ignited in 21% O2/CO2 v/v, and then only with a 2500 J, rather than a 1000J, igniter. An increase in O2/CO2 levels to 30 or 35% gave ignition patterns similar to those carried out in air with a further increase to 40% having little additional effect. In addition the minimum ignition concentration decreased with increase in O2. Heterogeneous combustion or gasification of the coal by CO2 appears to be confirmed by comparing weight loss results for air and O2/CO2 mixtures respectively for an equivalent peak pressure rise.

Jan 1, 2009

By Jeremy Spearman, Mark Lee, Jon Taylor, Neil Crossouard, Bramley Murton

"SUMMARYThis paper describes challenges faced when executing a programme of monitoring to measure the dynamics of currents and sediment plumes at a seamount and the solutions identified to deliver the measurements. The study site was the Tropic Seamount, which extends some 3300m above the surrounding seabed and is found at the southern limit of the Canary Island Seamount Province. The purpose of the study, which forms part of the Marine E-tech project, was to provide information on the interaction of flows with the seamount and to assess the behaviour of sediment plumes that could be generated from potential seabed mining operations targeting the recovery of ferromanganese crusts. Since the crest of the seamount is submerged to a depth of 1000m, much of the work was undertaken using remotely operated and autonomous vehicles supported by measurements from the surface vessel. Despite only limited information on currents being available for planning purposes, the combination of short term forecasting using a 3-dimesional hydrodynamic model of the study area coupled with the collection and analysis of reconnaissance data collected during the first phase of measurement activities made it possible to plan and execute a number of detailed hydrodynamic experiments on the seamount crest. The results of these experiments have advanced the understanding of the behaviour of sediment plumes in the deep ocean and will ultimately improve our ability to manage the impacts which may arise from deep sea mining operations."

Jan 1, 2017

By Lawrence Addicks

T HIS has been a most momentous year in the annals of the Institute. We have been in the midst of a situation which, were it not for the convulsions of social unrest with which life is surrounded on every side, would have attracted the attention of the world at large. I do not refer to the desperate campaign for new members. That has gone on much as usual except that, this being leap year, the annual proposal to the M. & M. Society has been omitted. Nor do I refer to the desperate situation which we found in other directions, the spread of Bolshevism, the burning of the Engineers' Club, the fact that the selling of copper appears to have become one of the lost arts. No, I speak of the great question which has to be. settled once and for all, as to whether this great Institute should adopt simplified spelling. The whole trouble started in the ranks of the California Hysterical Society. It appears, while most of the San Francisco members can read and write, several of them cannot spell. It also appears that the Secretary, in editing the Transactions, has perhaps made just a little bit too much of a point of employing the correct Stoughton idiom. At any rate, the rebels filed an amendment to the constitution, and the stage was set for civil war, with perhaps more stress on war than on civil.

Jan 1, 1920

By F M. Weir, M Fowler

A discrete fracture network (DFN) approach involves numerical modelling that explicitly represents how defects may be spatially distributed through a rock mass. A DFN is a 3D realisation of the ‘smaller scale’, non-deterministic defects; it is not an attempt to model larger, deterministic structures that should be identified as part of an engineering geology model. The approach utilises structural data in stochastic analyses to give a range of possible models that provides a tool for visualisation and analysis of a rock mass and indicates the potential large-scale slope or tunnel performance and stability.Stochastic fracture modelling for rock mass characterisation has significantly advanced over the past 25 years. With recent improvements to field data collection and computational power, it has become recognised internationally as a valuable tool for modelling some geomechanical problems encountered when designing excavations in fractured rock masses.This paper provides an introduction to the DFN approach, particularly the necessary input parameters and derivation of these from typical structural data sources, such as boreholes or scan line mapping. Of particular importance for engineering applications is validation of the simulated fracture network and techniques for doing so are discussed here.CITATION:Weir, F M and Fowler, M, 2014. An introduction to discrete fracture network modelling and its geotechnical applications, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 435–444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By I Canbulat, A Mcquillan

This paper presents a parametric analysis showing the impact of virgin in situ stresses on a shallow (less than 100 to 150 m) high slope in a jointed sedimentary rock environment. Slope stability is assessed at varying ratios of slope orientation and horizontal stresses. The results of this study indicate stress conditions should be included in stability assessments of excavated slopes, particularly where structure is orientated perpendicular to the direction of horizontal stress. Some consideration of stress state is applied in deep open cut pits (eg those with planned excavations of 400–1200 m) (Myrvang et al, 1993; Stacey et al, 2003; de Bruyn et al, 2014; Kozyrev et al, 2015). Dodd and Anderson (1972), Kalkani and Piteau (1976), Lee (1978), Coulthard et al (1992), Noorani et al (2011) have studied the effect or horizontal stress and its impact on slope stability, showing that tensile stresses tend to develop at the crest of the slope, with larger tensile zones for higher horizonal stresses and steeper slope angles (Stacey, 1970, 1973; Sjoberg, 2013). However, the consideration of virgin stresses on shallow slope stability is less frequent (Lynch et al, 2005; Dight, 2006; Lucas, 2006; Sjoberg, 2013). This has led many geotechnical engineers to believe the impact of virgin in situ stresses on open cut slope stability is minimal and not worth time or consideration in modelling, or their effects on slope stability are still poorly understood (Stacey et al, 2003; Sjoberg, 2013).

Nov 29, 2022

By C. N. Bailey

Let's review the economic factors in mill design. Talking about engineering economics in mill design reminds me of an old' saying "There are several ways to handle women but nobody knows what they are." I'm sure that the same economic factors do not apply to each of our mill designs, but for the sake of emphasis, it is well to review a few of them. They are so simple that we are apt to feel they are not important. Other speakers today are talking about the engineering factors of mill design, but I'm asking the question "Have we checked the economic factors involved in these designs? Have we checked the obvious? Many great discoveries have resulted from analysis of the things that appeared to be obvious all the time. What are some of these economic factors? Perhaps the most basic one is simply the value of minerals in place if minerals have value in the ground, they have value only because many important and different considerations add up to the probability that the minerals can be mined, beneficiated and disposed of profitably. The size formation and quality of the ore body, the distance from market, and the transportation available to the market area, depreciation rates, taxes, and the ownership interests involved are but some of the factors that must dovetail into the answer of profit, an answer prerequisite to hoped-for financing.

Jan 1, 1961

By S T. Jarvis

Colliery spoil is the major constituent of colliery spoil ærockpasteÆ which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m3 section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m3. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully used for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over 11 mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By Luiz Flávio Pereira Costa

O quartzo contido no concentrado, medido pelo teor de SiO2, é um dos principais itens de controle de qualidade do concentrado produzido em usinas de beneficiamento de minério de ferro. Nas usinas de beneficiamento da Samarco Mineração S/A o processo de concentração é realizado em etapas de flotação reversa de quartzo. São utilizadas tanto células mecânicas quanto colunas de flotação. A especificação do concentrado final produzido na usina de beneficiamento é obtido em uma etapa de flotação em colunas (3 colunas; 3,6mX14m). Com o objetivo de melhorar a performance desta etapa de flotação em colunas foram identificadas algumas oportunidades de melhoria, a saber: substituição dos spargers por slan jet; redistribuição e reposicionamento dos borbulhadores; substituição de chapéu chinês e do distribuidor de polpa equalizando a alimentação das colunas; otimização dos parâmetros de processo (vazão de ar e camada de espuma); realização de testes de flotação em bancada com amostras do fluxo que alimenta as colunas variando a dosagem de coletor. Nos testes em bancada uma éter-amina foi utilizada como coletor de quartzo. Os testes de bancada mostraram a possibilidade de reduzir o teor de SiO2 no concentrado de forma significativa aumentando a dosagem de coletor até 75g/t. A partir das modificações no sistema de aeração, distribuição da alimentação das colunas e com a adição de coletor, a taxa de redução de SiO2 passou de 20% para 40%.

Aug 16, 2017

By K. Yoo

Cuprous oxide is one of the oldest antifouling agents and also acts as red pigment in these paints. In printed circuit board manufacturing industries, waste etchant contains a substantial amount of copper ion. In the present study, a process was suggested for recovering cuprous oxides from the waste etchant and optimum conditions were investigated to recover the cuprous oxides. The process consists of two steps: in first step, Cu powder is added into wastewater solution, and cupric ions re-duce into cuprous ions (Cu+Cu2+?2Cu+), where cuprous ions precipitate as cuprous chloride; In second step, cuprous oxide is synthesized by adding NaOH into cuprous chloride solution (2CuCl+2NaOH?Cu2O+NaCl+H2O). Optimum conditions were investigated to recover cuprous oxide in the processes. When copper powder was added into wastewater with copper ions, Cu concentration decreased from 15.6% to 2.6% and ORP decreased from 620 mV to -59.9 mV. This result shows that cupric ions reduced into cuprous ions. XRD data indicated that the precipitate was cuprous chloride powder. Using the cuprous chloride recovered and NaOH solution, cuprous oxide was synthesized. To investigate the optimum condition, various NaOH solutions were added into water with CuCl, and then pH, ORP, Cu concentration, Cu contents in precipitates were analysed. XRD data showed that main component of precipitates was cuprous oxide.

Jan 1, 2014

By M P. Sandy, J B. Albrecht

"Narrow vein mining can be loosely defined as mining operations involving orebodies with a true thickness of less than 4 m. Some authors have limited the term to steeper-dipping orebodies where the ore will rill under gravity. However, ænarrow veinÆ can also legitimately refer to some of the flatter orebodies, such as many of the platinum, chrome and gold deposits of Southern Africa, and several in Australasia including Bullen (at Norseman), Sunrise Dam, Telfer (Patterson, 1993) and the famous æflatmakesÆ at the Emperor Gold Mine in Fiji (Gordon and Harmse, 1993). Where the orebody dip is less than about 40¦ additional effort is usually required to remove the broken ore, including the use of scrapers, hydraulic monitors or remote-operated excavators (Tombs, Buckingham and Hancock, 2008).Working in such narrow orebodies presents particular operational and geomechanics challenges. A range of mining methods have been developed or adapted to exploit narrow orebodies including:cut-and-fill,narrow vein bench or longhole stoping,Alimak stoping,shrinkage stoping, and methods for shallow dipping orebodies (including Airleg and mechanised methods).The paper discusses some of the advantages and disadvantages of each method with a focus on geotechnical aspects including mining sequence options, stress management, ground support requirements, dilution and recovery.CITATION:Sandy, M P and Albrecht, J B, 2012. An overview of geotechnical issues in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 185-194 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Ian J. Graham, Cornel E. J. de Ronde

New Zealand lies astride a convergent plate boundary that extends north-eastwards from the Taupo Volcanic Zone (TVZ) to Tonga. This boundary is marked by the Kermadec arc, c. 1200 km of which falls within New Zealand’s EEZ, and which is host to numerous volcanic edifices both on the arc and in a zone immediately behind the arc to the west. In 1999, thirteen volcanic centres in the southern 260 km of the arc were surveyed for their hydrothermal plumes with seven of them discharging vent fluids into the surrounding ocean. Three of the seven volcanic centres have had mineralised rocks recovered from them during dredging and submersible operations, namely Brothers, Rumble II West and Clark. Presentday plume data combined with mineralogical evidence indicate that the vent sites at Rumble II West and Clark are waning, although the presence of Cu-rich sulphides in samples recovered from Rumble II West suggest there may be a massive sulphide (Cu-Zn-Pb-Ba ± Au) deposit located within the caldera. Brothers volcanic centre is host to the largest polymetallic mineral deposit discovered along the Kermadec arc and has numerous, up to 7 m tall chimneys within a c. 600 x 200 m area located on its NW caldera wall. Geochemical data indicate that concentrations of base metals are variable and depend critically on sample type. When combined with mineralogical and plume data, this indicates addition of a magmatic fluid component to the vent fluids.

Aug 24, 2006

By J. -C. Tedenac, C. Colinet, X. Tao, P. Jund, R. Viennois

"We report an ab-initio study of the stability and electronic properties of transition metal silicides in order to study their potential for high temperature thermoelectric applications. We focus on the family M5Si3 (M = Ta, W) which is stable up to about 2000 °C. We first investigate the structural stability of the two compounds and then determine the thermopower of the equilibrium structure using the electronic density of states and Mott’s law. We find that W5Si3 has a relatively large thermopower but probably not sufficient enough for thermoelectric applications.IntroductionIn the search of new sustainable energies, thermogeneration of electricity is one of the promising ways, notably because it is able to produce electricity from different kinds of heat wastes and to its portability. However, despite recent progress in the field, the state-of-the art materials have specificities making their mass-production difficult or even impossible: toxicity (thallium, chalcogen or/and pnictogen based alloys), weak abundance (tellurium based alloys) or cost (germanium or rare-earth based alloys). For all these reasons, finding thermoelectric materials without these drawbacks is vital if we wish to use high temperature thermoelectricity for generating electricity in the near future. Due to their abundance, low cost and low toxicity, transition metal silicides are candidate materials of primary interest and the slightest advance in this field would immediately find an application for the thermogeneration of electricity."

Jan 1, 2011

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By T Peters

The Kibali Gold Mine is currently comprised of several open pits, a 3.5 Mtpa underground mine and a 7.5 Mtpa processing plant. Development of the underground operation commenced in December 2012, with initial access established through twin surface declines, followed by the commencement of a blind sink 8 m diameter rock hoist shaft in March 2013. Stope production started in December 2014 with ore and waste trucked to surface. The 755 m deep blind shaft sink was completed in August 2015 together with the cutting and equipping of three main station levels. Two of these levels provide access for the establishment of the underground materials handling system as well as the main dewatering system for the mine. This paper covers the process of determining the optimal location of the Kibali hoisting shaft relative to project-specific critical factors, and then focuses on the design and implementation journey associated with the off-shaft development that essentially encompasses the Material Handling System (MHS) for the mine. The journey starts from the findings of the previous owners Feasibility Study (FS), a subsequent Optimised FS, followed by detailed engineering through to implementation. It was identified during implementation that a significant change in the designed off-shaft layout was required following detailed underground geotechnical and hydrogeological investigations. In addition, the paper provides details on the MHS performance since commissioning to steady state, and on key learnings relating to the overall project process.

Mar 29, 2023

By M. F. Dibble

The technology available for mining of underwater mineral resources such as placers and phosphorite, typically occurring with variable amounts of overburden, has remained largely unchanged for decades. The traditional bucket ladder dredge with maximum digging depth of 48 m and monthly capacities about 500,000 m3 still reins as the only heavy duty mining system capable of working the tough materials characteristic of heavy metal placers. Attempts at adapting the bucket wheel cutter-suction dredge to these severe conditions have not yet been successful except in moving small volumes from shallow depths. High capital cost (20-30 million U.S. dollars), high cost of overburden removable, and turbidity generation for the bucket ladder are often significant negative factors in mining operations where this system remains the only viable alternative. The Japanese continue to advance the technology of their submersible dredge pump system powered by specially adapted, direct drive electric motors. Present systems are designed primarily for working surficial deposits of aggregate to depths as great as 90 meters, the pump suspended by cable from a surface vessel with an eductor pipe leading from the pump to the vessel. Such a system may prove adaptable to a variety of surficial deposits including phosphorite, shell and heavy minerals in addition to aggregate. However promising for the exploitation of surficial deposits, little advantage can be expected for the deeper buried and more difficult deposits.

Jan 1, 1986

By D. MOORE, A. REINSBAKKEN, A. J. Sinclair

The Gypo quartz vein lies near Oliver, British Columbia, and was quarried between 1955 and 1968 for decorative chips. The vein is one of many quartz veins hosted by the Late Jurassic Oliver Plutonic Complex, specifically by the porphyritic quartz monzonite phase of the pluton. The vein has a known length of 155m and a thickness of 46m. It strikes east-west and dips at 60 degrees to the south. Mineralogy is predominantly quartz with minor pyrite, muscovite, fluorite, calcite, apatite and manganese; trace amounts of chalcopyrite, pyrrh otite, marcasite and molybdenite also are present. Quartz in the vein is zoned. A thin grey quartz zone found near the margins of the vein fades gradually into white quartz, which comprises over 95% of the vein. Late-stage boxworks cut earlier mineralization, particularly fluorite, which occurs as pods in a zone fairly close to the hanging wall. Sulphide minerals are found in a centrally located zone in the quartz vein. The hanging wall of the Gypo veins is altered only slightly, but thefootwall is altered extensively to a greisen of muscovite and grey quartz. Evidence suggests that early in rhe vein development, the adjoining country rock was feldspathized. As grey quartz and muscovite was deposited, a period of intensive greisenization and fracturing occurred which so weakened the rock that a central block of greisenized country rock foundered. This provided the open space in which the vein was deposited.

Jan 1, 1984

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

By Randolph A. Koski

Recent investigations located at least six major massive sulfide deposits (dimensions measured in tens to hundreds of meters) within a 50-km-long segment of Escanaba Trough, the sediment-covered axial valley of southern Gorda Ridge. The sediment fill is intercalated silt and sand turbidites and hemipelagic mud with a maximum thickness of 500 m. Several volcanic edifices, spaced at approximately 15-km intervals along the ridge axis, penetrate and locally breach the sediment. The largest sulfide deposits form mounds and ridges on the steep flanks of structurally unstable sediment-capped blocks that have been uplifted above the volcanic edifices; both sediment and sulfide deposits are undergoing rapid erosion and redeposition. Although hydrothermal activity appears to be absent at most sulfide fields, 220°C fluids are discharging from the tops of sulfide mounds near 41°00'N lat, 127°31'W long. Recent pillow lavas and sheetflows erupted onto the sediment-covered sea floor less than 500 m away from the active vent field. The massive sulfide deposits have compositional characteristics that differ from deposits formed on sediment-free spreading axes. The Escanaba Trough deposits include Fe- and Cu-rich, Zn- and Pb-poor massive sulfide mounds, polymetal (Zn-Fe-Pb-Cu-As-Ag-Sb-Sn) sulfide vent structures, abundant barite-rich chimneys, crusts, and sinter cones, and thermogenic petroleum in the sulfide and sediment. Sulfate-rich crusts have high Au values ranging between 2 and 10 ppm. The unusual mineral assemblage at Escanaba Trough

Jan 1, 1989

By D. L. Thompson

Foreword The complete history and early development of the Sullivan mine was fully covered in a paper entitled 'The Development of the Sullivan Mine and Processes for the Treatment of its Ores', prepared by the staff of the Consolidated Mining and Smelting Company of Canada, and presented at the Annual Meeting of the British Columbia Division of the Institute at Trail in October, 1924. At a subsequent meeting at Blairmore, Mr. E. G. Montgomery read a paper on the mine, and in 1926 Mr. M. M. O'Brien brought the subject up to date at the joint meeting of the American and Canadian Institutes at Cranbrook. The present paper is necessarily based largely on these earlier accounts. Discovery and Early Development The outcrop was discovered in 1892 and the property was bonded and later sold to the Sullivan Group Mining Company, of Spokane. From 1896 to 1899, surface stripping and test pits (at A) around the outcrop exposed a vien of sulphides with varying amounts of lead and zinc. In some places, a 35 per cent lead ore carrying 15 ounces of silver was found. These lenses were of commercial value. With the completion of the Kimberley branch of the Canadian Pacific railway, in 1900, some systematic development was started. A shaft l00 feet in depth was sunk (at B). Shaft-house, boiler-room, and compressor-plant were erected, and a steam diamond-drill was put into operation.

Jan 1, 1929