Search Documents

By Han Kook-Nam, Lawson F

The recoveries of the three cobalt minerals in the Mount Cobalt deposit, cobaltite CoAsS, erythrite CO3(AS04)8H20, and new cobalt mineral with a composition approximating 2CoO.CaO.Fe203.2As205.11H2O were investigated using physical and surface-chemical processes.Over 80 per cent cobalt recovery was achieved by tabling a cobaltite-mineralized sample, while about 76 per cent cobalt recovery was obtained by dry feed magnetic separation of a sample containing erythrite and the new cobalt mineral. The resultant primary magnetic concentrate with a cobalt grade of 5.5 per cent, was able to be upgraded to 14.4 per cent cobalt by regrinding .and a further magnetic separation.Electrophoretic mobility - pH responses for each of the three cobalt minerals were found to be similar. Each mineral remained negative over the pH range 3 to 11 and was most negative at mildly alkaline pH values.Cobaltite was floated effectively with amyl and ethyl xanthate collectors under acidic conditions at collector concentrations of 10-2M to 10-5M. Erythrite showed a similar flotation response using 10-sM amyl xanthate. The practical application of these laboratory separations to an industrial process is suggested.

Jan 1, 1976

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

NIM Reports Report No. 1563 Neutron activation analysis of samples from the Kimberley Reef Conglomerate. Report No. 1569 The use of DDTU as an analytical reagent for the noble metals. Special general meeting A Special General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 14th November, 1973. The President, Mr P. W. J. van Rensburg, opened the meeting at 9 a.m. and read the notice of the meeting, which was as follows: Colloquium and general meeting CONSTRUCTION OF SLIMES DAMS A General Meeting and Colloiquum on the above topic was held on November 14th and 15th, 1973, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 135 delegates and was opened by the President at 9.10 a.m. Orange Free State Branch PROCEEDINGS OF THE ANNUAL GENERAL MEETING The Annual General Meeting of the Branch was held in the Western Holdings Cant,een on Tuesday, 11th September, 1973, at 7.00 p.m. Book Review Westwood, W., and Cooper, B. S. Analytical methods in use in non-ferrous minin~ and metallur~ y: a selective review. London, Institute of Mining and Metallurgy, July 1973. 54 pp. £3.50.

Jan 12, 1973

By Hugh R. Wilson

Echo Bay's Waste Management Program for its Lupin Mine was developed in response to the terms and conditions of the water license issued to the mine in 1981 by the Northwest Territories Water Board. The gold mine, located about 80 km (50 miles) south of the Arctic Circle, commenced production in 1982. The Waste Management Program was based originally on the total containment concept, contingent on future treatability testwork results indicating the best treatment method to ensure pond discharges would be in compliance with stated Northwest Territories Water Board discharge criteria. To assess the various treatment technologies, an investigative program was established to determine the most effective means for treating the tailings pond water. In the course of milling, about 850,000 m3 (11 million cu yd) of tailings are produced annually that require appropriate management to protect the environment. This annual tailings stream consists of about 175,000 m3 (229,000 cu yd) of solids and 675,000 m3 (883,500 cu yd) of water. Following the completion of the required waste management studies, a two-ponds-in-series concept of tailings impoundment was developed. To attain this concept, the tailings impoundment area would require modification and construction to enable the use of such a system.

Jan 1, 1991

By Robert Jedrzejczak

The Endako Mine is an open-pit molybdenum mine located in the north central region of British Columbia, Canada, about 960 km (600 road miles) north of Vancouver. Production for the latter part of 1992 was expected to averaged 63.5 kt/d (70,000 stpd). Of that amount, 27 kt/d (30,000 stpd) was the mill feed. This production is achieved with five 11.5 to 14.5 m3 (15 to 19 cu yd) electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 320 mm (12.25 in.) electric rotary drills. There are three ore zones delineated into pit areas: the Endako, Denak East and Denak West. Present mill feed source is the southeast stage of the Endako Pit. Stripping is carried out in the south wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM-BM-flotation circuits. The majority of the molybdenum sulfide (MoS2) is roasted on site to produce technical grade molybdenum oxide (M003). A portion is further refined and treated to yield a 99.9% pure MoS2 product.

Jan 1, 1993

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By P. Chris Pistorius

"Ilmenite smelting involves partial reduction of iron oxide from a slag consisting mainly of T1O2, T12O3 and FeO, yielding as products iron (with approximately 2% carbon) and titanium slag. Slag purity requirements preclude any fluxing additions, and the aggressive nature of the slag necessitates a furnace freeze lining. Large departures from thermal and chemical equilibrium hold in the smelter, with possible implications for process stability. The slag is approximately 150K. hotter than the metal, which means that the metal temperature is below the slag melting point; this difference in temperature has been shown to lead to formation of a solid TisOs-rich layer between the slag and metal. Recent equilibrium measurements have confirmed that the slag and metal are not in chemical equilibrium either, with significantly more reducing conditions in the metal than in the slag. After solidification, the pseudobrookite slag structure is metastable below approximately 1400K, and may transform upon slight oxidation.IntroductionThe natural mineral ilmenite is the main source of titanium, which is mainly used to produce Ti02-based pigments. Ilmenite has the ideal formula FeTiC>3, but natural minerals can be partially oxidized (to contain some Fe3+), and typically contain MnO and MgO as well, together with associated silicate minerals. Smelting is one of the methods to upgrade ilmenite for subsequent T1O2 pigment production; smelting involves partial reduction of FeO to form metallic iron as a byproduct and titanium slag as the main product. Reduction is typically controlled to yield a slag which contains around 10% FeO, 85% (Ti02+Tij03) and 5% impurity oxides (mainly MnO, AI2O3 and S1O2). An example of a typical average slag composition from reduction of South African ilmenite is shown in Table I. As this indicates, a significant side reaction is reduction of some T1O2 to T12O3. The relative extents of reduction of FeO to Fe and of Ti02 to T12O3 are such that the slag stoichiometry is close to that of the pseudobrookite phase [1]. Pseudobrookite has the structure AB2O5 (where ""A"" and ""B"" are different cation sites); the phase which makes up the bulk of solidified titanium slag has the AB2O5 structure and stoichiometry [2], and can be viewed as a solid solution of FeTi20s, T13O5, ÌçÔÀ2è5, MgTi20s, AI2T1O5 and C^TiOs [1]. This solid-solution phase is referred to as ""pseudobrookite"" or ""M3O5"" in this paper."

Jan 1, 2012

By W. D. Robertson, J. -P. Briant, M. Gell

The distribulion of dislocatiorls genevnted during the propagalion of hydrogen-induced cracks in Fe-Si cryslcrls was studied as a funclion of temperature f-110o lo 243°C) and silicorz conlenl (3.1 and 4.2 pct). It zoas found that the clislocntiotl densily and the size of the plctslic zone increased with increasing tempevalnre and decreasing silicon conlent. Furtheruvzove, there was a correlcrtion in the dislocalion patterns formed around cracks that propagated at different tempevattrt-es in cvyslals of diffevent silicon contents such that a 1 pcl itlcverise in silicon content was equivalent to a lemperaluore redziclion of approximately 120°C. The experimenlal YeSnllS were compaved with the results of an elastic-plastic wodel that relates the size of the pluslic .zone to the cvack length, internal pressure, and yield stress. it was found that the clzunges in the dislocctlion cryrays with lemperature and combosition can be e-kplaincd by the lemperatrnre and composilion dependence of the yield stress. An wmtsual feature of this study was the observation of low -temperature noncrystrrllogruphic cracks. PLASTIC relaxation can occur at the edge of a moving crack by the operation of pre-existing dislocation sources or by the creation of new sources in a region of perfect 1attice.l'2 The amount of relaxation in a given crystal depends on the crack velocity and the temperature, and can determine whether a crack propagates in a brittle or a ductile manner.1-3 Tetelman and Robertson4 observed microcracks m Fe-3 pct Si single crystals that formed on (100) planes by the precipitation of hydrogen gas during electrolytic charging at 23°C. The plastic deformation accompanying crack propagation was observed in the form of dislocation etch pits and an extensive analysis has been made of the size, shape, and crystallography of the dislocation arrays5-7 This paper describes the effect of temperature on the plastic deformation generated around hydrogen-induced cracks in Fe-3.1 pct Si and Fe-4.2 pct Si single crystals. The observations are compared with the results of an elastic-plastic model for yielding around a crack containing an internal pressure. 1) EXPERIMENTAL PROCEDURES The composition of the materials used in this study are given in Table I. Single crystals of alloy A and the 4.2 pct Si alloy were grown by the strain-anneal method; crystals of alloy B and the 5.1 pct Si alloy were cut from an ingot grown from the liquid. he ~ingle-cr~stal metallographic specimens had a Cross section of 0.100 by 0.050 in. with a length of at least 3/8 in. Specimens were annealed for 3 hr at

Jan 1, 1968

By L Richards, R L. Brathwaite, C Mazenga

Underground mining of gold-silver bearing quartz lodes was carried out in the great mines at Martha Hill, Waihi over 70 years from 1882 until 1952. Shafts and stopes reached a total depth of 600 m on 16 levels, with workings extending laterally some 1.6 km, and as new reefs were discovered the workings extended beneath parts of the township. Over their long life the mines produced 1217 tonnes of gold-silver bullion from processing 12.2 million tonnes of mined ore. In the early-1980s drilling proved large reserves of gold and silver ore remaining in stock-work zones between the previously mined lodes. This led to a new era of mining at Waihi with the opening of the Martha Hill open pit in 1988. A series of three sink holes have formed above unfilled stopes of the Royal lode. In 1999 a sudden collapse crater 40 m in diameter occurred near an occupied part of Waihi, placing in danger several houses and a busy street. This crater formed close to a similar crater that occurred in 1961. The 1999 collapse resulted in subsurface investigations and risk assessment studies being commissioned by the local Hauraki District Council. However, a further 50 m diameter collapse crater in December 2001 formed in a residential area, swallowing and wrecking an occupied house, fortunately without injuring its five occupants. Two other houses were perched on the crater rim. The 2001 collapse led to an acceleration of the work being carried out by the Institute of Geological and Nuclear Sciences Ltd. (GNS) to identify the extent of the old underground workings at Waihi. For the risk assessment detailed rock mechanics analyses were made to consider the stability of the underground mine stopes, in terms of the stope back, hangingwall, footwall and crown pillar failure mechanisms, as well as void migration. The collapse crater areas were analysed using using several methods, including analysis to simulate the probability of void migration from unfilled stopes to the surface using the @Risk program. The analyses show that in the cases of the actual collapse craters, the voids have a high probability of migrating to the surface, thus providing a method of testing the void migration modelling. Modelling analysis applied to the remaining stopes of the old underground mines show there are further areas where void migration from unfilled stopes has a high, medium and low probability of reaching the surface as a collapse crater. The locations of these probabilistic hazard zones were outlined using the @Risk modelling and deterministically by using the dimensions of the historical collapses applied along the length of the stopes. Consideration of the æincubation periodÆ (the time interval between the cessation of mining and the occurrence of collapse) and comparisons with mine subsidence histories overseas, indicates that further collapses are likely to occur over the next 50 years. Risk assessment estimates made using property values and occupancy levels within the three hazard zones, were compared with Societal and Individual Risk criteria. Results indicate that safety within the high and medium zones may be unacceptable.

Jan 1, 2003

By Charles H. Jacoby, Stanley J. LeFond

Salt, or halite, has a long and most varied history. While we know the Chinese were producing salt as early as 3000 B.C., the first written reference to salt appears in the book of Job recorded about 2250 B.C., which reads: "Can nothing which is unsavory be eaten without salt?" We do not know when man first used or realized that he needed salt. Perhaps one of our early Eolithic ancestors noted a piece of salt shining along the shore of a salt lake or a bay. He may have been attracted by its shining luster and tasted it. He found that it had a tart, zesty, distinctive flavor and perhaps chewing a large piece, became ill. However, by experimentation he soon learned that taken in the proper proportions salt was a very pleasant additive to his food. He may have noticed, too, that it increased his feeling of well-being. Thus, when the curtain of recorded history rises, we find man using salt for his health's sake, seasoning his food with it, feeding it to his animals, and using it in many superstitious and religious ceremonies. These uses, however, are a far cry from the uses for salt today. The first attempts of white man to make salt in continental United States were reported in the year 1614, while the first commercial production was in 1753 from the Kanawha licks. Practically all this salt was for human consumption, preserving food, and curing hides. Prior to the coming of the white man, Indians are known to have made salt from salt springs such as those that existed at Avery Island, LA, Charleston, WV, Saltville, VA, and Onondaga, NY. In 1862 the first rock salt was mined in the US from the Avery Island salt dome. Almost immediately thereafter, rock salt was mined at Saltville, VA and then at Retsof, NY in 1885. Of the more than 39 million tons produced annually in the United States, about 58% or 23 million tons are consumed by the chemical industry in the production of chlorine, caustic soda, hydrochloric acid, sodium metal, and some 30 other basic chemicals. These basic chemicals, in turn, are used in the preparation of approximately 14,000 chemicals which range from soap and detergents, to such chlorinated hydrocarbons as DDT, BHC, carbon tetrachloride, etc. Utilization of cavities created in salt beds and domes has grown rapidly since 1947 until now the waste salt is creating an ecological problem. The uses for both dry- and solution-mined cavities range from the storage of liquid hydrocarbons to containerized storage of toxic wastes, from compressed air for the peak shaving of power to storage of nuclear wastes. Geology Mineralogy Properties: Because of its simple structure, halite, the mineralogical name for salt, was the first structure to be analyzed by X-rays. It has the following properties: Formula: NaCl (Na-39.34%. Cl2-60.66% ) Crystallography: isometric, hexoctahedral, 4/m 32/m Space group: Fm3m A0: 5.627 kX Cell contents: Na4CI4 Habit: usually cubic, rarely octahedral, massive, granular to compact Physical properties: Refractive index: 1.554 Twinning: observed on {111} Cleavage: {001} perfect Fracture: conchoidal, brittle

Jan 1, 1983

By W. B. Greer, J. J. K. Daemen

Introduction The performance of seals in boreholes, shafts and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall et al., 1982). This research involved the installation, extensive hydraulic testing, removal and post-test examination of a 10-cm-long x 10-cm-diam cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble Peak in the Santa Catalina Mountains, AZ. A test hole was diamond cored in the recrystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diam, and dips at 10.4°. The hole extends between two drifts and thus is accessible from both ends. Seal installation Surveys to assist in selecting the interval to seal consisted of core logging, video logging and constant-head injection tests using a straddle-packer unit. The location selected, 3 m from the lower end of the hole, had low hydraulic conductivity (3 x 10-10 to 3 x 10-9 cm/sec) and was free of significant fractures. The grout used, an expansive Class A cement, was provided by Dowell-Schlumberger, Tulsa, OK. A grout mass about 1.5 m in length was installed, with a dump bailer, above a temporary mechanical plug. Groundwater in the hole, if any, was minimal during placement. After 13 days of curing, the grout mass was partially drilled out from both ends, leaving a seal 10 cm long. Water distribution in rock mass The distribution of water and fluid pressure in the rock mass near the seal appears to be complex. The generally dry condition of the borehole and rock mass suggests that the rock mass near the seal was unsaturated prior to the injection tests of this research. The injection tests presumably created an expanding saturated zone around the seal. However, anomalously high fluid pressures, consistently recorded by one of two piezometers installed near the seal, suggest connection to a source of significant natural hydraulic head. Comparable head variations for closely spaced piezometers have been reported by others (Sowers, 1976). [ ] Seal testing The seal was tested for 3.5 years, using steady constant-head, tracer travel-time, dye-injection, head-buildup and transient constant-head tests. These tests are fully described in Greer and Daemen, 1991. In the head-buildup test, transient flow occurs through the seal (and rock mass) to a closed, water-filled interval of the borehole adjacent to the seal. The test consists of monitoring the rise in head in the closed interval until steady conditions are approached. The test may be analyzed in terms of a one dimensional analytical model to obtain the effective hydraulic conductivity (Ks) and specific storage (Sss) of the seal. Analysis in terms of an axisymmetric three-dimensional numerical model may yield properties of both the seal and rock mass.

Jan 1, 1993

The following is an incomplete list of members and guests who called at Institute headquarters during the period June 10, 1918 to July 10, 1918. F. C. Alsdorf, Tucson, Ariz. Emory M. Marshall, Camp Raritan, N. J. Juan F. Brandes, Santa Barbara, Cal. Jacques S. Negru, Camp Niagara, Ont. .H. Smith Clark, Kansas City, Mo. Arvid E. Nissen, High Bridge, N. J. J. S. Cunningham, Charleston, W. Va. Richard G. Place, So. Strafford, Vt. W. G. Eberhardt, Tucson, Ariz. Frank H. Probert, Berkeley, Cal. M. Eldredge, Bombay,. India. Martin A. Roudabush, Osterburg, Pa. A. D. R. Galloway, Accra, W. Africa;. P. H. Royster, Minneapolis, Minn. F. Hanst, Harrisburg, Pa. J. L. Schueler, Peoria, Ill. B. B. Hood, Chrome, N.. J. Henry B. Smith, New Britain, Conn. Paul S. King, Wilmington, Del. W. G. Sommer, Peoria, Ill. E. D. Kinney, Anaconda, Mont. A. L. Toenges, Roanoke, Va. E. W. Kohl, Jr., Philadelphia, Pa. G. D. B. Turner, Butte, Mont. James W. Love, Knoxville, Tenn. A. T. Ward, Bellefonte, Pa. Edwin A. Austin, formerly with the Yukon Gold Co., is superintendent of the Elkoro mine at Jarbidge, Nev. John W. Beard is now with the Cia Minera de Penoles, Ojuela, Dgo., Mexico, via Mapimi. R. S. Bonsib has accepted a position with the United States Emergency Fleet Corporation as District Safety Engineer, San Francisco, Cal. Albert Burch has been appointed by the Bureau of Mines to encourage the mining of chrome. F. B. Caldwell is working for the U. S. Bureau of Mines, under Albert Burch, in the investigation of chromite deposits. W. A. Carlyle has taken over the duties (in addition to his own) formerly assigned to E. P. Mathewson with the British America Nickel Corporation, at Sudbury, Canada. R. M. Catlin received the honorary degree of Doctor of Science at the recent commencement of Rutgers College, New Brunswick, N. J. S. K. Dahl is giving up his position as mill superintendent with the Messina Mines, which have been suspended, and is returning to this country. Algernon Del Mar has become manager of the Techatticup mines, El Dorado Canyon, Nev. Robert Dye has succeeded D. L. Forbes as manager of the Teck-Hughes at Kirkland Lake, Ont., Canada. J. O. Elton, superintendent of the Anaconda company's electrolytic zinc plant at Great Falls, Mont., is doing special work with the U. S. Bureau of Mines. R. B. Caples takes charge of the plant in his absence. George H. Gibbs has resigned his position as engineer at Messrs. T. & 1. Bradley & Sons, Ltd., Darlaston blast furnaces, Darlaston, and is now located at "Belmont." Litchfield Road, Rushall, Walsall, England. William D. Gordon, for the past 7 years manager of The Mine & Smelter Supply Co. at El Paso, has been elected president of Camphuis, Rives & Gordon,. Inc., and has opened American headquarters for the company at 81 New Street, New York, N. Y. E. Harms, for the past 16 years inn charge of metallurgical operations of the Torreon, Mexico; lead and copper smelter, has resigned and is now located at El Paso, Tex.

Jan 8, 1918

Research on the Design and Processing Characteristics of 320 m3 Air-Forced Mechanical Flotation Cell

Sep 13, 2010

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095' and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,' no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References 'C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By A. V. Pavlov, V. A. Grygorian, Kossyrev, A. E. Semin, A. Korostylev

A new way of producing low-silicon ferrosilicon from iron-ore materials in a new type of aggregate-oxygen reactor is presented. The oxygen reactor process is based on using the calorific combustibility and reducibility of carbon materials inside the aggregate. The key to the process is successful post-combustion of carbon monoxide above a layer of a solid coke bed. Initially the possibility of production of grades of ferrosilicon containing 20 to 25% Si (FeSi20-FeSi25) was studied on a laboratory model of the oxygen reactor. Quartz sand and iron ore concentrates (from Russia and India) were used in the laboratory tests. This test work demonstrated that a ferrosilicon grade FeSi15 could be obtained directly from raw iron ore (containing 75.9 % Fe2O3 and a maximum of 23.8 % SiO2) without using rich iron-ore concentrates. The process was successfully tested on a pilot furnace at Serovsky metallurgical plant. Very promising results and efficiency parameters were achieved. The consumption of materials for 1t of ferrosilicon (15 % Si) production was as follows: 1567 kg raw iron ore, 591 kg of coal (in a composition of ore-coal briquettes), 299 kg of coke (for coke bed formation), and 815 m3 of oxygen.

Jan 1, 2004

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

By R. J. Boyd

SUMMARY The productivity of drill and blast methods of mining in hard rock is limited by the cyclic nature of the operation, and a plateau of performance has been reached, even with the most advanced equipment developments. Higher mine operating costs and lower metal prices have more than ever generated the need for breaking through these productivity barriers. After initial field testing The Robbins Company has designed and manufactured, on a joint venture basis with Mount Isa Mines, Ltd., Australia, a prototype "Mobile Miner" for continuous cutting of hard rock. This paper describes the cutting concept, the initial application of a completed 1,156 m (3792 ft.) long 14% decline, actual performance and delay analysis, developmental modifications, anticipated performances of a fully developed machine, and possible future applications. Sincere appreciation is expressed to the management of Mount Isa Mines, Ltd., for allowing access to the data used in this paper. The views expressed here are those of the author and not necessarily those of Mount Isa Mines, Ltd. INTRODUCTION A paper titled, "Design and Development of a Mobile Mining Machine", was presented by J.P. Kindsvater at the RETC, New York, in 1985. This paper described the evaluation of a test fixture in an andesite quarry near Seattle, followed by design, construction and

Jan 1, 1987

By C. D. Thompson

Pile load test programs were carried out in 1984 and 1985 at Stelco's and Dofasco's Steel Making Plants in the Hamilton Bayfront area. 323.9 mm outside diameter by 9.5 mm wall thickness Grade 3 steel closed-end pipe piles were driven to practical refusal at depths of 21 to 30 m in very dense silt till with Delmag D30 open-end diesel hammers. Ultimate bearing capacities of up to 5330 kN were proved by dynamic monitoring and static load tests. Allowable bearing capacities of 1780 kN were achievable on production piles without undue difficulty. It was found that the impact stress at the top of the pile was controlled by the yield strength of the steel rather than a useable upper limit based on the modulus of elasticity. A bearing to impact stress ratio of 1.2 at practical refusal was observed to be reasonable but conservative at this site, and is felt to be generally applicable for piles driven to practical refusal elsewhere. Dynamic monitoring during production pile driving was able to show that apparent relaxation was caused by pre-ignition of the hammer when visual observations indicated that pile driving was proceeding satisfactorily.

Jan 1, 1987