Search Documents

By Ivano Andreis, Georgios Kalamaras, Mario Liti, Sebastiano Pelizza, Filippo Avesani

"THE SS640 AGRIGENTO-CALTANISSETTA PROJECT The Caltanissetta tunnel is part of the works for the construction of the second 28km-long maxi section of the SS 640 motorway of Porto Empedocle, from km 44 to the junction of Imera in Sicilian hinterland. Amongst other major infrastructure works, the €740 million ANAS (Italian national roads and highway administration agency) project consists of four twin tube tunnels three of which are being excavated by conventional means. The longest tunnel, underpasses the Caltanissetta city and has a length of 3.9km under a maximum overburden of 120m. The JV consisting of CMC of Ravenna and TECNIS SpA won the design & built tender in 2010. Construction started in early spring 2012 following the approval of detailed design and later on the approval of design for construction. THE CALTANISSETTA TUNNEL The Design Phase Tender design and detailed design foresaw the construction of 13.4m excavation diameter tunnels that were to be enlarged in a second phase to create, every 600m, 50m-long tunnel sections for emergency parking. During the design for construction project phase the JV proposed to replace the 13.4m tunnel with a 15.08 excavation diameter that incorporated apart from the two 3.75m wide lanes a 3.25m wide continuous emergency lane. This significant tunnel section modification was associated with better road safety conditions, simpler and safer construction procedures, better statics for the tunnel section while in terms of overall cost the solutions were equivalent.Geologic context The tunnel is located in the middle of the geologically known Caltanissetta basin that is intersected by various tectonic structures. The geologic context for the tunnel scale, was defined in collaboration with the University of Catania in early project phases. For almost its entire length the tunnel is excavated in the Terravecchia formation that represents the lower part of the stratigraphic sequence that was formed in the Tortoniano period of Miocene. The quite complex geological model is also characterized by the presence of the so-called Trubi formation that consists of clay and marl clay. Almost 90% of the tunnel traverses formations that are quite similar in terms of excavation behavior. Exception to this are thrust zones and a calcareous stretch of the alignment. This last segment has a length of 200m and was identified since the very beginning as a tunneling challenge due to the combination of very poor geotechnical properties and an important water load."

Jan 1, 2016

By Patrick E. Durnal, Henrik Dahl

"A joint venture of Ben C. Gerwick Inc., Sverdrup (now Jacobs) and DMJM (now DMJM + Harris) designed the $779 million seismic upgrade of the Richmond - San Rafael Bridge over the San Pablo Bay in the San Francisco Bay Area and provided construction support to Caltrans. Construction of the marine foundation retrofi t was completed by a joint venture of Tudor Saliba/Tidewater/Koch-Skanska and their subcontractors: Pomeroy Precast Construction, AGRA Foundations, Dutra Construction and Vortex Divers. Construction management and inspection was performed by Caltrans with the support of various consultants. MARINE FOUNDATION RETROFIT SCOPEThe retrofi t design of the submerged foundations included:??A total of 476 tension and compression micro piles (290- 1140 kips or 1290-5071 kN) installed through cored holes through the underwater bells at 31 pier locations??Fourteen 126/150/164 inch (3.20/3.81/4.17m) diameter CISS (Cast-in-steel shell) concrete shear piles (1160- 2660 kips or 5160-11832 kN) installed through new precast concrete pile cap extensions??Twelve CIDH (Cast-in-drilled-hole) shear piles (1060- 2130 kips or 4715-9475 kN) with 150 inch (3.91m) diameter steel shells to top of bedrock and 30 ft (9,14m) long and 11 ft (3.35m) diameter rock socket installed through new precast concrete pile cap extensions The specifi ed post bid test boring revealed deeper bedrock at one pier location allowing deletion of the rock socket. Thus 15 CISS and 11 CIDH shear piles were installed at 11 pier locations - 9 piers with 2 piles and 2 piers with 4 piles. Cut off elevations for the shear piles ranged from 46 ft to 60 ft (14.0m to 18.3m) below mean sea level and cut off for the micro piles was 8 ft to 46 ft (2.44m to 14.0m) below mean sea level. Almost all foundation retrofi ts required work under limited headroom conditions. Underwater construction connections required innovative design details and construction techniques for each pile type. The 11 piers had 22 precast concrete pile cap extensions installed in pairs and connected by either tremie concrete closure pours or by large pipe struts. The precast pile cap extensions were strapped underwater using large steel bands wrapping around the belled piers with grouted annulus. The precast pile caps were founded with 14 inch (355mm) diameter steel pipe piles, which were either support piles or seismic tension and compression piles. The seismic piles were connected in grouted corrugated steel pipe sleeves cast into the new concrete pile caps."

Jan 1, 2007

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By Clayr Alexander

Stillwater Mining Co. (SMC) is engaged in developing, extracting, processing and refining palladium, platinum and associated metals (PGM)from the J-M Reef. This geological formation is located in Stillwater, Sweet Grass and Park counties in southern Montana. Associated byproduct metals include rhodium, gold, silver, nickel and copper. SMC’s current mining operations are near Nye, MT. The company is currently developing a second underground palladium and platinum mine, the East Boulder project, about 21 km (13 miles) west of the Nye operations. A 5,650-m (18,550-ft) tunnel is required to gain access to the ore-bearing horizon (J-M Reef).

Jan 1, 1999

By J. Davies

This paper describes the successful management and construction of the 5.18 m (17 ft) diameter, segmentally lined, North Dorchester Bay CSO storage tunnel in Boston, MA. This 3,300 m (10,830 ft) long tunnel was mined through variable soft ground with only 6 m (20 ft) of cover, using an earth pressure balance tunnel boring machine. These extensive data collected from the projects unique automated and internet accessible geotechnical and TBM monitoring system, will be examined and used to explore the relationships between geological conditions, TBM operating parameters and measured settlements. The paper will also discuss the use of screw revolutions as an indicator of muck volume.

By Claus Becker

The new, 2.600 m long pipe under the river Elbe in Hamburg/Germany required for 2 traffic lanes, emergency lane and space for utilities a boring diameter of 14,20 m(46,6 ft). According the geology (glacial deposits consisting of clay, sand and marl, all containing big boulders) a Slurry-Shield with crusher was selected. With a minimum cover of 7 m and a maximum pressure of 5,6 bar extensive ground treatment was necessary to make the drive feasible. The machine contains a lot of new developments. The drive was finished in spring 2000 so all experiences can be reported. A special risk sharing contract avoided completely litigation.

Jan 1, 2001

By T. L. Dobecki

Numerous seismic techniques have proven to be important and cost effective aids to both coal exploration and nine planning. Projects conducted by Sandia in recent years have sham seismic refraction is a valuable tool for determining overburden properties while high resolution, 2-0 and 3-D seismic reflection surveys are the primary means of napping coal seam distribution, structure, and continuity. Further, seismic methods utilizing existing boreholes (e.g. downhole, crosshole and guided wave) provide detailed measures of overburden/interburden modulus variation, seam continuity, and calibration for other seismic surveys. Examples include mapping faults of 2-10 m threw in seams 3-15 m thick at depths of 80-300m.

Jan 1, 1982

[Aalde, Kaare, ('40) New Mexico School of Mines, Socorro, N. M. Abadesco, Enrique A., ('39) Univ. of the Philippines, Manila, P. I. Abdul-Ahad, A., ('39) Montana School of Mines, Residence Hall, Butte, Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acker, Voscoe, . ('39) Agricultural & Mech. College of Texas, College Station, Tex. Acosta S., Gonzalo, ('40) Univ. of Texas, Univ. Sta., Box 1785, Austin, Tex. Adams, Albert, ('38) New Mexico School of Mines, Socorro, N. M. Adams, Charles W.,' ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams, Hugh T., Jr., ('39) Univ. of Oklahoma, Norman, Okla. Adams, Jack L., ('39) Univ. of Oklahoma, Norman Okla.]

Jan 1, 1940

Since 1955 Gaspe Mines has produced 144 million tonnes of ore, averaging 0.87% Cu, mined from two open pits and underground workings. In 1994, four exploration drill holes discovered a buried porphyry/skarn Cu-Mo deposit at depths of between 1000 m and 1700 m below the top of Porphyry Mountain. The mineralization and alteration associated with the Porphyry mountain quartz monzonite does not outcrop. A total of 19,500 m of drilling in 12 drill holes has outlined 200 million tonnes grading 0.73% Cu and 0.08% Mo. Mineralization occurs as veins and disseminations of chalcopyrite and molybdenite. Drilling and feasibility studies continue.

Jan 1, 1998

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014

By Nguyen V. V

The development of structural defects in the overburden material immediately behind a production blast was studied using surface and subsurface techniques. A significant increase in vertical and horizontal fracture intensity was recorded. The extent of fracturing into the highwall appeared to be dependent on the structural and petrologic characteristics of the various lithological units and the relative position of the explosive charges. A shallow zone of disruption to a depth of 10 m and extending to around 30 m from the newly formed highwall crest was recorded. Horizontal fractures in lower units of the overburden sequence were recorded at distances up to 50 m from the new highwall Face.

Jan 1, 1981

By M. J. Baker

Energy and Minerals Australia Ltd are undertaking a study of the recovery of uranium from the Mulga Rock Deposits in Western Australia. Approximately 80-90% of uranium identified to date is present as tabular layer up to 5 m thick within a lignite seam 30 m to 50 m below surface. Other metals are also present. Metallurgical studies at ANSTO Minerals laboratories in Sydney have focused on identifying a suitable uranium leaching process and assessing the possible downstream impacts of the organic material in the ore. The extraction of other metals has also been examined. This paper provides the results of testwork performed at ANSTO to date.

Aug 1, 2010

By J. C. Fisher

Nucleation theory is applied to martensite nucleation in substitutional iron alloys. Composition fluctuations are neglected, and a steady rate of nucleation is predicted for any composition and temperature. The maximum rate of nucleation (as a function of temperature) is shown to be measurable only for on extremely narrow composition range, being too great or too small outside this range. A number of experimental observations, including completely isothermal transformation in some alloys and composition-dependence of M. temperature in others, are compared with the calculated behavior. IN a previous report,¹ nucleation theory was applied to the formation of isothermal martensite in an Fe-Ni-Mn alloy. The experimental observations of Cech and Hollomon² were accounted for quantitatively. It now is of interest to examine the predictions of nucleation theory with respect to martensite transformation in substitutional iron alloys of other compositions. Since Fe-Ni alloys have received considerable attention, both as to their transformation kinetics and their free energies, they will be treated in detail, although the results apply with equal validity to other substitutional alloys. In substitutional alloys, where composition fluctuations can be neglected in volumes of critical nuclear size, the rate of nucleation of martensite in subcooled austenite is¹ n - Nv exp (—W*/kT) [I] where the free energy of formation of the critical size nucleus is W* = 8192 p (?² s³) [2] In the expressions for n and W*, the symbols have the following meanings: N is the number of atoms per unit volume; v, the atomic vibration frequency; 8, a function of the elastic constants of austenite and the shear angle of martensite; , the austenite/mar-tensite inter facial free energy; and ?fc is the free energy change per unit volume accompanying the transformation. Jones and Pumphrey² have determined the austenite to martensite free energy change as a function of nickel content and temperature for Fe-Ni alloys. Their expression is ?F = 2500 C + 1.25 (1 —C)?FFc cal per mol [3] where C is the atom fraction of nickel, and ?Ffe is the free energy change per unit volume for pure iron as tabulated by Zener4 (or, equivalently, Fisher"). From Eqs. 1 to 3, it is possible to calculate isothermal nucleation rates as a function of temperature and composition for Fe-Ni alloys. The only unknown parameter is (?² s³). The best value of this parameter for Fe-Ni alloys, determined from M. temperatures in a manner to be described shortly, is (?² s³)= 9.92 (10)21 cgs units [4] Taking this value of (?² s³), C-curves for isothermal nucleation were calculated for Fe-Ni alloys of several compositions, and are plotted in Fig. 1. It is evident from Fig. 1 that completely isothermal nucleation of martensite in Fe-Ni alloys can be observed experimentally for only a very narrow range of compositions. Cech and Hollomon find that a nucleation rate of about 10' nuclei per cc per sec is as fast as they can follow dilatometrically, and a rate of about 10-1 nucleus per cc per sec is about the slowest that can be measured conveniently. If the nucleation rate is to lie between the limits 10-1 10 the nickel content of an Fe-Ni alloy must fall in the atomic fraction range 0.299 5 C 5 0.302. Nickel contents lower than 0.299 correspond to nucleation rates too great to follow, and those higher than 0.302 to nucleation rates too slow to measure in a reasonable time.* In view of the narrow corn- position range in which successful isothermal measurements can be made, it is not surprising that only one substitutional alloy has been described' that comes close to being in the proper range.

Jan 1, 1954

By R. Grierson, R. N. Parkins

The m.echanica1 properties, at high lzomologous temperatures, of the intermetallic compounds InzBi and Mg17A112 were measured as a .function of temperature, applied strain rate, previous thermal and mechanical history, and composition. Mgl,Al12 was investigated ilz compression, whereas Zn,Bi was investigated in tension. A decrease inflow stress with increasing strain was observed jor both alloys. The results obtained are discussed in terms of the dislocation-multiplication processes in these materials. MANY intermetallic compounds are reported to undergo a brittle-ductile transition at high homologous temperatures.' There is evidence in the literature that some of these compounds exhibit a large yield drop when plastically deformed.'j3 Both of these forms of behavior are shown by the covalent elements germanium and silicon4,5 and also by certain ionic compounds.8 The present work is a study of the deformation, at high homologous temperatures (>2/3 Tm), of two intermetallic compounds, In2Bi and Mg17Al12. InzBi has a disordered hexagonal structure7 (c/a = 0.598) and a solubility range of 32.3 — 33.2 at. pct Bi.8 It has a melting range from 72° to 89°C. Mg17Al12 has an ordered bcc (A12 type)7 structure and exists over the range 50 to 60 at. pct Mg8 with a melting range from 437° to 462°C. We have been unable to find any reference to previous investigations of the mechanical properties of BiIn,. Novikovg has reported that cast samples of Mg17A112 show ductility, when bend-tested, at temperatures above 380°C. EXPERIMENTAL Ingots of In2Bi and Mg17Al12 were melted under an argon atmosphere and cast, in situ, in a graphite crucible. The materials used were of 99.99 pct purity. The alloys prepared contained 66.9 at. pct In in the case of In2Bi and 58.4 at. pct Mg in the case of m17A112. The ingots were homogenized and then extruded. Two-in.-diam Mg17Al12 ingots were extruded at 375°C to give 3/8-in.-diam rod. The rate of formation of this rod was 0.25 in. per min. One-in.-diam InzBi ingots were extruded at 20°C, using a rate of 1 in. per min, to give 1/8-in.-diam rod. In both cases the extruded rod had a recrystal- lized, fine-grain, structure. (For Mg17Al12, d = 11.2 µ; for BiIn2, d = 22 µ.) Mechanical-property determinations were made in a hard-beam machine, in tension in the case of In2Bi and in compression with Mgl7Al12. The tensile tests were on specimens having a gage length of 1.1/2 in. and a diameter of 1/8 in. The compression tests on Ml7A112 were on specimens of 3/8 in. diam by 3/8 in. high and the ends were coated with poly-tetrafluorethylene to minimize friction. RESULTS In2Bi. Fig. 1 shows, particularly at the higher applied strain rates, that In2Bi exhibits a marked yield drop as the deformation increases to about 2 pct, after which the material shows neither hardening nor softening up to 15 pct strain. The magnitude of the yield drop, the stress in the region of flow under constant stress (the stress plateau), and the 0.5 pct proof stress were all dependent upon the applied strain rate according to an expression of the form

Jan 1, 1965

By Jim Morris, Davin Ishii

The major source of water for Southern Nevada is Lake Mead. However, the existing pump station located on Lake Mead is inadequate for one of the fastest growing areas in the United States. In order to keep up with the increasing demand for water in Las Vegas, a parallel system is being constructed. The intake for this system is being constructed approximately 68.58m (225ft) below the surface of Lake Mead. The lake tap consists of installing casing and secant piles to support the shaft collar, excavating a 21.34m (70ft) deep intake shaft, and installing a3.66m (12ft) diameter steel liner.

Jan 1, 1999

By T. Strong

"Selectively recovering pentlandite from high levels of pyrrhotite presents a technical and operational challenge. The liberation characteristics and also the chemical environment is critical to performing a successful separation. Reviewing the mineralogy to understand the characteristics of the ore and the plant flotation behavior is fundamental to designing a successful improvement program.At Savannah Nickel the challenges presented by a falling nickel price required a rethink of the flowsheet to improve the project economics through improving the concentrate grade and recoveries. Glencore Technology reviewed the plant performance and proposed and tested solutions to improve the grade performance of the concentrator with the support of the plant team. A pilot plant comprising a M20 IsamillTM followed by an L500/1 Jameson Cell was operated on various plant streams. In addition to the pilot plant, flotation surveys and a plant based laboratory program was used to supplement the plant understanding and within two weeks significant improvements were identified and demonstrated. The combination of the pilot operation and the plant based laboratory program was able to quickly demonstrate the improvements and test with equipment that is fully scaleable from pilot plant to full scale.IntroductionPanoramic Resources Limited is a Western Australian mining company formed in 2001 for the purpose of developing the Savannah Nickel Project in the East Kimberley region of Western Australia. Panoramic successfully commissioned the $65 million Savannah Project in late 2004. The process plant at Savannah comprises a single stage crusher, SAG mill, flotation, thickening and filtering stages to produce a bulk nickel, copper, cobalt concentrate. Metallurgical recoveries average 86-89% for nickel, 94-97% for copper and 89-92% for cobalt. The plant was originally designed for a throughput of 750,000 tonnes per annum, but has consistently outperformed the design specifications.Due to low nickel prices the Savannah Nickel mine and processing plant were placed into care and maintenance in May 2016. Prior to suspending production Glencore Technology was engaged to investigate options to improve the concentrate grade. With the discovery of Savannah North in 2014 and the Savannah North Scoping Study demonstrating LoM ~8 years and Mining Inventory of 6.07Mt @ 1.26% Ni, 0.64% Cu and 0.09% Co significant future potential exists. By completing pilot plant studies prior to shutting down, the plant engineering studies can be completed and the plant readied for restart by the time the nickel price improves."

Jan 1, 2017

By Jose R. Hernandez-Aguilar, Chris J. Martin, Rob Thorpe

"This study presents an approach to establishing relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside flotation cells. Bubble size Db, superficial gas velocity Jg, and bubble surface area flux Sb (Sb = 6Jg/Db) measurements were obtained along with metallurgical samples in full-size equipment processing different ore types. The gas dispersion was manipulated by changing the operating conditions of the cells (gas flowrate and frother type) and the metallurgical performance (grade-recovery) was determined. In two cases, the Sb had a strong relationship with grade and recovery, hence, Sb could be used as practical operating parameter. In another case, Sb did not correlate with recovery. The reasons were attributed to creating small bubbles using frothers with desired anti-coalescence properties. This illustrated that bubble size was the key parameter for metallurgy rather than Sb.INTRODUCTIONUnravelling the mechanisms that govern the relationships between metallurgical performance and the characteristics of the bubble population (gas dispersion) inside a flotation cell remains a major challenge. Information on this subject is scarce in the literature, particularly, plant-scale data. The report of Jameson and Allum (1984) appears to be the first gas dispersion study conducted in industrial (mechanical) cells. To introduce concepts, some aspects of their work are reviewed here.The prime motivation of that study was to establish whether any particular cell design (among 44 cells surveyed) could produce very small bubbles (< 0.1 mm), which laboratory research suggested would increase the recovery of fine particles. Although one of the outcomes was that the (examined) cells did not seem to produce such small bubbles (Sauter mean1 D32 ˜ 0.9 mm), the analysis highlighted the importance of including other factors. Jameson and Allum indicated that, besides bubble size (Db), other characteristics of the bubble dispersion should be considered, namely: gas holdup ?g – the fraction of cell volume occupied by bubbles, superficial gas velocity Jg – is the gas flowrate divided by the cross-sectional area of the cell and, bubble surface area flux Sb – the rate of production of (new) bubble surface area (m2/s) per m2 of cell cross-sectional area. It should be noted that, whereas Jg, ?g and Db can be measured directly, the Sb is derived: Sb = 6Jg/Db, where Db is usually substituted by the Sauter mean diameter (D32)."

Jan 1, 2006

By David Estrella, Hector M. Lizama, Jhonny Carrión

"Microcel™ sparging systems were installed on one column of the molybdenum cleaner circuit and one column of the copper first cleaner circuit at Antamina. The Microcel™ system is known to generate finer bubbles than jetting-type spargers, and smaller bubbles have been associated with higher recoveries in flotation. Alternating tests were carried out on the molybdenum column, using either jetting-type spargers or the Microcel™ system. Experimental conditions of gas flow rate, wash water rate, and froth depth were tested. Use of Microcel™ decreased the bubble sizes from 2.6-2.9 mm to 1.5-2.0 mm. In addition, Microcel™ improved both unit molybdenum recovery and unit molybdenum concentrate grade. In the copper first cleaner circuit, side by side tests were carried out that compared the Microcel™ column with a parallel columns fitted with jetting-type spargers. Best results were obtained at manifold pressures of 260-290 kPa, where bubble sizes of 1.6-2.6 mm were observed. In either copper or molybdenum flotation, the Microcel™ system required only 50-60% of the gas flow used by jetting-type spargers.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and has a nominal 100,000 t/d mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone [Evans et al, 2005]. Ore body thickness is 100 to 150 m and has the shape of a flat-lying crescent. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper, zinc, and lead-bismuth concentrates are transported by pipeline down to the port of Huarmey. Molybdenum concentrates are bagged and trucked to port."

Jan 1, 2008