Search Documents

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By G. Lindkvist

Roasting of concentrates with high impurity levels is normally done in multiple- hearth furnaces where the concentrates are heated with oilfired burners in order to remove As, Sb and Bi before the final sulfide oxidation. Although it is a countercurrent heat exchange process it uses a lot of oil. In order to develop an energy saving, and from a working environmental point of view a less harmful process than the multiplehearth process, pilot-plant tests have been done in a two-stage fluidized bed for partial roasting. The test materials have been As-rich concentrates with 8-25 % As some 5b and Bi. The Cu-content was 0-28 %. The tests have been successful with <0.3 % As,in the calcine and with an elimination of 5b between 80 and 90 %. In order to achieve the proper conditions for good impurity removal, 1.e. right temperature,residence time and sulphur potential, the tests were performed in a special designed roaster. The roaster consists of two beds with the facilities for recirculation of calcine, preheating of the blast, and possibility to use oxygen enrichment. The construction makes it easy to control the reactions that generate the heat in the bed and reduce the amount of dust that passes through the cyclones. As two roasting steps are used, the possibility to obtain optimal conditions for impurity removal is improved and the calcine can either be smelted to a normal matte, or after being dead-roasted in the second stage, be leached in the normal way for gold extraction. The calcine was smelted with slag. The matte and the slag obtained had low quantities of impurities in the matte and a favourable distribution of impurities to the slag.

Jan 1, 1983

By Dave Tahija

"Many investigations are being performed with the goal of removing carbon dioxide from the atmosphere and permanently storing it in geologically stable settings. At the same time, carbon dioxide in the form of dissolved carbonate is steadily accumulating in the world's oceans. Both carbon dioxide sequestration and oceanic accumulation are constrained by the aqueous thermodynamics of the carbonate system. These constraints are illustrated using the STABCAL computer model to generate potential-pH and aqueous distribution diagrams of seawater in contact with various pressures of carbon dioxide gas. STABCAL diagrams and titration simulations are also used to model some potentially useful cation-carbonate sequestrationsystems.IntroductionAtmospheric carbon dioxide concentrations have risen dramatically in the past couple of centuries and are rising still, primarily as a result of human activities, especially the burning of fossil fuels. Increased atmospheric carbon dioxide concentrations have been implicated as a main cause of global warming but have other effects as well.Rising levels of atmospheric carbon dioxide result in increased concentrations of dissolved carbonate complexes in water, including the oceans. These dissolved carbonates interact with other dissolved substances, altering overall seawater chemistry, most noticeably causing lowered pH levels.Some of these chemical changes are observed directly, for instance the general drop in oceanic pH, [1], while others can be inferred and predicted using thermodynamic modeling. The chemistry of dissolved carbonate in seawater is not especially intricate, as such chemical systems go, but neither is it simple enough to be worked out on the back of an envelope. Interactions between the several simple carbonate species and all the major dissolved cations in seawater should be considered, as well as the effects of competing anions, especially chloride and sulphate, since they are much more abundant than carbonate in seawater."

Jan 1, 2011

By Jorge Alberto Soares Tenório, Victor Bridi Telles, Denise Crocce Romano Espinosa, Felipe Fardin Grillo, Vicente de Paulo Ferreira Marques Sobrinho, José Roberto de Oliveira

"This research aims to study the process of incorporation of the metal iron in electric arc furnace dust (EAFD), from a steel mill producing long steel by liquid iron in addition to the changing temperature of 1400 degree Celsius altering experimental conditions such as how to add the EAFD (as received and in the form of briquettes), the percentage of EAFD to be added (10, 20 and 30% of initial weight of sample pig iron) and the time of withdrawal of the sample of pig iron and slag (30 minutes after the addition of EAFD). Previously, the EAFD will be characterized using the following techniques: chemical analysis, particle size analysis, X-ray diffraction, scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) microanalysis. After characterization, the eletric arc furnace dust to be added to the bath of liquid iron, will be divided into 2 types: the first order of addition will be in the form ""as received"" from the plant and the second is through the agglomeration of EAFD in the form of briquettes. The achievement of fusion experiments in laboratory scale, will take place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of the metal iron will use graphite crucibles. A flow of inert gas (argon) will be maintained inside the furnace during the experiments. It is expected that the results obtained at the end of the research allow the evaluation of the iron metal incorporation of eletric arc furnace dust in hot metal bath.IntroductionThe steel industry generates a variety of solid wastes, liquid effluents and gaseous emissions at various stages of processing. The electric furnace dust (EAFD), generated in electric arc furnaces, represents a major problem for their content of chemical elements such as zinc, iron, chromium, cadmium, among others, issued to the atmosphere during the manufacture of steel[1]."

Jan 1, 2012

By Kunio Nakahara, Kashiwagim Junichi, Takao Hayashi

"There are many problems for electronic devices and parts which were caused electrostatic damage by static electricity. It is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating. Mitsui Mining & Smelting Co., Ltd. developed metal oxide type electroconductive pigment PASSTRAN (trade mark) Type-IV which is barium sulfate coated with SnOz(Sb) thin electroconductive layer. This paper shows about pigment characteristics and film condition of antistatic transparency paint which contained PASS TRAN.L.IntroductionRecently rapid development of electronics technology diffused electronic devices and products to Office, Factory, Laboratory and our life. But the other side, there are many problems for electronics parts which were caused electrostatic damage under static electricity. Demand of antistatic materials were become lager by this situation.There is close relationship between surface resistivity of material and static electricity. If the surface resistivity of object is enough low (under 109 Q /Sq), static electricity is dissipated quickly. So it is necessary for prevention of electrostatic charge to decrease surface resistivity of material using electroconductive coating.1) There are many type of electroconductive materials, for example, carbon black, metal powder, electroconductive polymer and so on. Especially, carbon black is used for general purpose by reason of its low cost, but it has big problem of black color. It can not get any color without black, and it caused contamination of carbon.In recent years, metal oxide electroconductive pigment (ECP) was developed and used for special purpose which demands transparent coating or easy dispersion to make ECP paint or endurance under hard environment and so on. Mitsui Mining & Smelting Co., Ltd. developed electroconductive pigment PASSTRAN Type-IV which is BaS04 coated with electro-conductive Tin oxide layer."

Jan 1, 1998

By Jim Sarvinis, Mark Berkley, David Clarry, Jason Berzansky

"Technologies developed to sequester CO2 or use CO2 for enhanced fossil fuel recovery are currently being utilized across the globe. Taxation regimes and CO2 credit trading are becoming drivers for a number of projects. Some mining companies have also identified ancillary opportunity to sequester CO2 in their by-products; recent work in the alumina industry is a prime example. In addition to process plant emissions, mining companies are becoming increasingly aware of their overall carbon footprint, including CO2 generated during the production of utility power. New power plant designs, in various stages of development, include CO2 separation and sequestration techniques. This paper summarizes the state-of-the-art for these technologies; including integrated gasification combined cycle (IGCC) power plants. A concept to use the gasification products as reductant in metallurgical processes is also described. The relevance of technology from power plant designs with post-combustion capture to the processing of off-gas generated in metallurgical facilities is also reviewed.IntroductionGlobalization and international economic growth have led to an increase in energy demand worldwide, and a corresponding increase in greenhouse gas (GHG) emissions. In 2005, 81% of global energy supply came from fossil fuels [1]; and while alternative energy technologies are emerging, it will require many decades to curb society’s fossil fuel dependence. Given the global concern of climate change and its scientific relationship with anthropogenic carbon dioxide (CO2), there is at present great interest in the development of techniques to reduce emissions of CO2. While most of these efforts are related to power generation and energy efficiency, the development of technologies for CO2 capture may offer opportunities in reducing emissions from industrial processes."

Jan 1, 2008

By Jens Decker

"In consideration of energy savings the ideal refractory furnace lining should possess the following features:??Lowest thermal conductivity possible in order to avoid heat loss.??Single component lining in order to allow freeze plane changes caused by wear, infiltration and temperature changes of the furnace.??Resistance against mechanical wear from cleaning tools and stirring in order to allow maximum output without equipment downtime due to maintenance.??Resistance against thermo-chemical attack from aluminum and alloying elements.However, refractory materials with a low thermal conductivity typically possess a higher porosity and this leads to lower strengths and resistance against chemical attack and wear. Hence, as a compromise, multi layer linings are required in order to meet energy saving standards.In this paper we present the features of chemically phosphate bonded dense and light weight refractories and how such refractories can contribute to energy savings.IntroductionIn several reports, the U.S Department of Energy published theoretical energy requirement limits for aluminum production as a future target, with recommendations on how to reduce energy losses. The reports provide a basic description of the processes and equipment involved, their interrelationship, and their effects on energy consumed. The report uses onsite process measurements as benchmarks that industry uses to compare performance between facilities and companies [1]. The energy consumptions used in this paper are primarily based on numbers published by the Department of Energy. However, their reports do not consider the potentially significant energy losses from process interruptions due to a lack of preventive maintenance and material deterioration over time. Further, the Department of Energy reports do not consider equipment costs and availability. Energy input to metal output depends on factors beyond energy losses through the furnace wall. For instance, a focus on energy savings should consider fixed output costs due to depreciation of the equipment and the plant."

Jan 1, 2009

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

By Milorad Cirkovic, Mile Bugarin, Vlastimir Trujic

"Industrial scale testing was performed in the plant-site of Bor Company. Charging sample was from 4-5 tons for each particular test. All operations in industrial scale investigations were carried out in one furnace. For the aim of successful realization of experiments, and primarily for safety and prevention the risk of toxic contamination the working environment, a plant was designed and constructed for cooling and wet dedusting of gases formed during smelting process, zinc removal and flame refinement of molten metal. For the requirements of industrial investigations a complete plant for cooling and wet dedusting of gases has been constructed for brass scrap processing. In this plant, the original ultra-sonic water spraying devices have been installed. The efficiency of such simplified system for gas treatment has been 98,6%. Introduction Permanent development of techniques and technology causes formation the considerable quantities of secondary raw materials that are much more relevant as the raw material base for many metals. Due to a fact that large quantities of metal, are concentrated in the waste materials, large consideration is given to this topic, and numerous technologies for this waste recycling are developed in the world nowadays. High energz price and permanent increase of metal price on the world market have made that secondary raw material tretament, for the aim of various metals production, becomes more and more relevant in the world. In comparison of metal production using enrichment and metallurgical treatment of primary raw materials, the non-ferrous metals production from secondary raw materials has a range of advantages, as well as: - Low level of capital investments, - High technological recovery of qualitative secondary raw materils, - Considerably low consumption of energetic resources regarding to the treatment of primary raw materials (ore and concentrate), - Reduced consumption of unrecoverable mineral resources, - Reduced enviroment pollution [1,6]."

Jan 1, 2008

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008

By Claude Lorenson

"The Spyrometer™ imaging pyrometer brings new dimension of imaging capabilities to temperature measurement technology by combining a high temperature video camera with scanning optical pyrometry. This gives the operators the ability to observe process conditions while measuring the temperature of virtually any object or region in the field of view. Since the lens tube of the camera can be air or water cooled, it is possible to see inside furnaces giving a very good view of many different types of metallurgical processes. Specific benefits in process knowledge and maintenance tasks for furnaces in different types of metal industries are discussed.1-Principles of Imaging PyrometryLens tube, camera and processorImaging pyrometry is the combination of video imaging and computer-driven pyrometry that measures the temperature of certain zones (selected by the operator) within the image viewed on the monitor screen. To obtain a detailed image of the metallurgical process under observance, it is necessary to place the optical objective of the camera close to the process. The Spyrometer™ (which is Quadtek's tradename for its imaging pyrometer) objective is housed in a lens tube that is cooled and permits insertion inside the vessel of interest. The length of the lens tube is chosen on the basis of making sure that the tip of the tube is just beyond the refractories lining the inside of the furnace. In most pyrometallurgical processes, we have found that the most reliable system set-up uses a water cooled shroud to cool the lens tube optics. A sapphire window provides maximum protection from the environment. Even in the case of the water cooled version, there is an air purge for the lens that keeps the objective clean and protects against hot metal splashes."

Jan 1, 1997

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By Alexander A. Knminskii

Polymorphism of BaR2F8 compounds is analyzed, and some peculiarities of obtaining monoclinic low-temperature (3-BaR2F8 crystals (R=Y, Ho-Yb) and orthorhombic high¬temperature a-ßaR2F8 crystals (R=Yb, Lu) by the Bridgman-Stockbarger growth technique are discussed. We pay a special attention to BaYb2F8:Er3+ crystals, which are able to generate both 2:µm SE using the new four-level operating scheme (4F9/2?4I11/2 laser channel) and 2- and 3-µm SE by means of the cascade scheme (4F92?+4I11/2?+4I31/2). This 2-µm generation of Er3+ ions has an advantage over similar SE of Ho3+ and Tm3+ ions (especially under diode laser pumping), that is important in designing the medicine and ecology laser. We report on orthorhombic BaR2F8 crystals with the ordered structure, a new crystalline materials for generating Ln3+ ions. The growth conditions are determined and orthorhombic BaLu2F8 crystals of several cm3 in volume doped with Ce3+, Nd3+, Ho3+, Er3+, and Tm3+ ions are obtained for the first time. Spectroscopic and laser characteristics of these crystals are discussed for Nd3+-and Era+-doped samples serving as representative examples. In particular, low-threshold stimulated emission was excited in 4F3/2?+4I11/2 channel of Nd3+ ions in the BaLu2F8. Room-temperature generation was obtained also at -1.317 µm wavelength for Nd3+ and at ~2.8 µm (several lines) for Era+ ions in this new laser crystalline host with a threshold of about 20 J.

Jan 1, 1997

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Yuanbo Zhang, Yongbin Yang, Guanghui Li, Zhengwei Yu, Yufeng Guo, Tao Jiang, Xiaohui Fan, Youming Hu

"Composite agglomeration process (CAP), as an innovative method for preparing blast furnace burden, was developed and has been put into operation in China. CAP is different from traditional agglomeration processes of iron-bearing materials involving sintering and pelletizing. Compared to the traditional agglomeration processes, CAP is characterized by several strengths such as permission of diverse iron-bearing materials in production, obvious improvement of permeability in the feed bed, decreasing the fuel consumption and remarkably increasing the productivity of sintering machine. Furthermore, the use of the composite agglomerates prepared with CAP is capable of obviating the negative effects caused by the differences in quality of sinter and pellets on the operation of blast furnaces. This paper mainly presents an overview of the principle and applications of CAP.Development Background and Principle of CAPhe traditional agglomeration processes including sintering and pelletizing have been the two predominant methods for preparing ironmaking burden from iron-bearing materials. Sintering is a way for agglomeration by heating the coarser fine ores (general granularity 0~10mm). The mechanical strength of irregular porous sinter is obtained by the solidification of molten phase at high temperature process. It has been shown that the production of high basicity sinter (R=1.8~2.2) is characterized by low energy consumption and high efficiency compared to low basicity sintering. Meantime, the finished high basicity sinter is characterized by good mechanical strength and metallurgical performance. Pelletizing is another way for agglomeration by firing wet green pellets, which are balled from the fine grained iron ores or concentrates. Based on the differences of chemical compositions, the finished pellets can be divided into acidic oxidized pellets, fluxed pellets, magnesium-bearing pellets, and so on. The acidic oxidized pellets are the dominant products of modern pelletizing."

Jan 1, 2012

By R. Schaller, Ch. Karcher, A. Thess

"Electron beam evaporation of liquid metals is an innovative technology increasingly used in industry to produce very thin coatings of high purity. In this process the surface of a metal ingot, placed in a water-cooled copper crucible, is heated by bombarding it with a high-energy electron beam gun. The material melts, forming a free surface and eventually starting to evaporate. The rising vapor cloud condensates as a thin film on a moving substrate. The strong energy input at the free surface gives rise to vigorous thermos capillary and buoyancy driven convective motion within the melt, leading to unwelcome heat losses. This paper aims to show how these losses can be reduced by optimizing the geometry of the crucible and by using external magnetic fields. We present both experimental and numerical results.IntroductionElectron beam evaporation of liquid metals [l] is an innovative PVD-technology which is excellently suited for the industrial production of high-quality coatings. In this vacuum process a high-energy electron beam heats up the surface of a metal ingot. The ingot melts and forms a free surface. A schematic view of the arrangement is shown in Figure 1. When the temperature of the free surface exceeds the actual (pressure-dependent) saturation temperature of the ambient gas, the liquid starts to vaporize. The rising vapor cloud finally condensates on a moving substrate located at some distance above. To guarantee a superior quality of the coating the melt is typically confined in a water-cooled copper crucible. The intensive cooling is necessary to avoid chemical reactions between the melt and the crucible walls, that is, crucible materials and their reaction products are practically excluded from evaporation."

Jan 1, 1999

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By Dachun Liu, Baoqiang Xu, Bin Yang, Yong Deng, Heng Xiong, Xiumin Chen

"In this paper, vacuum distillation technology has been employed to study the possibility and regularity of separating copper and enriching lead, silver and other valuable metals from copper- based multi component alloys. The result of experiment indicated the practicability of vacuum distillation dealing with copper base complex multi-component alloy to separating lead and silver, when the vacuum distillation temperature was 1637K, distillation time was 60min; residual gas pressure was 20-30Pa, the removal rate of silver was 95.86%, of lead was 99.63%; the evaporation rate of copper was 0.745%. The removal rate of arsenic, antimony and tin respectively were 83.09%, 48.12% and 24.54%. Vacuum distillation method is applicable for dealing with the copper-based multi component alloys, silver and lead can realize effective recovery.IntroductionCopper generally go with lead mineral, therefore, to remove copper from lead becomes an inevitable link in lead smelting. Dross from removed copper usually contains lead, arsenic, antimony, tin and noble metal silver. In abroad, soda ash-iron dust is adopted to process copper dross of this kind. The outcomes of this process are lead matte, wet lead, scoria smoke dust etc[1~5] The dominant components of all the outcomes are copper and lead. Moreover, in the process of tin smelting, copper contained by-products are produced, such as, crude tin alloy, tin lead electrolytic anode slime and so on. Copper content of all the products are ranging from few percentages to several tens percentage. Those products, no matter merge into main producing process, or separate treatment cost losses of valuable metal. For one hand, the containing of copper of outcomes from pyrogenic attack is less than 50%, for the other hand, a lot of valuable metal need to be processed, which increase the cost of retrieve."

Jan 1, 2013

By Seksak Asavavisithchai, Natthida Jareankieathbovorn, Areeya Srichaiyaperk

"Recycling of ADC12 alloy scraps for fabrication of open-cell aluminium foams has been conducted via pressure infiltration method of replication process. The scrap, up to 50 wt.%, was melted with pure aluminium billet, followed by infiltration in a replicated mold of polyethylene foam structure. Compared with the pure aluminium foam, the compressive strength and hardness are higher for the foams with recycled scraps. The increase in foam mechanical properties is due to the presence of Si hard phase in Al matrix. The strength and hardness of the foams also increase with increasing contents of the scraps.IntroductionRecently, open-cell metallic foams have been brought to considerable attention of many industries due to their superior properties; such as large surface area, high specific strength, thermal conductivity, high service temperature and excellent anti-microbial activity, that cannot be found in conventional materials [1, 2]. Typically, open-cell foams are used in functional applications for which a requirement of high strength materials is not demanded. Good examples of such applications include heat exchangers, bone-replacement implants, interconnects, catalyst supports, and sound insulators.Among all types of open-cell metallic foams, aluminium (Al) is the most widely used base metal, due to low material cost, low density, low melting temperature and good corrosion resistance. To improve mechanical properties of Al foam, modification of foam microstructure with addition of alloy elements or ceramic particles is commonly carried out [3, 4]. ADC12 alloy is a typical die-casting Al alloy with high content of silicon (Si) close to the eutectic point in Al-Si binary phase diagram. The alloy is extensively used in the casting industry, due to high wear and corrosion resistance, low coefficient of thermal expansion and excellent castability [5]. The mechanical properties of Al-Si alloy are strongly dependent of Si content."

Jan 1, 2012