Search Documents

By A. Grenoble

The mining of seams in close proximity can greatly accentuate interaction problems. At distances of less than 110 feet vertically interaction can occur for both over and under mining. Research into ground control problems resulting from undermining a previously mined seam has been carried out using finite element and body-loaded photoelastic modeling methods in conjunction with numerous case studies. Analysis of field data was used to validate and expand the model results. Research findings demonstrate situations under which the worst ground control conditions can be expected to occur for a specified geologic environment, depth, innerburden spacing and mining geometry. Special emphasis has been placed on the effects of pillar load transfer on the lower seam in terms of pillar and floor stability and roof control. Roof and floor condition indexes are used to summarize structural and lithologic conditions in the affected seam. The effects of joint orientation and continuity are incorporated in the analysis and the research results have been compiled into a software package for application by the field engineer.

Jan 1, 1984

By Thomas E. Marshall

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the miner may be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its' use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers From falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive pro-active ground control safety program. Also included is a cast history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

Jan 1, 2000

By William J. Gray

The Roof Control Division of MSHA's Pittsburgh Safety and Health Technology Center has been conducting a program to evaluate methods employed by the U.S. coal mining industry during recovery of longwall faces. The objective of this effort is to provide information on safe and efficient roof control methods currently being used to recover longwall faces. In addition to a literature review and extensive contacts with MSHA and industry personnel, 14 mines were visited to observe firsthand various aspects of longwall recovery. It is hoped that the dissemination of this information will aid in the prevention of accidents and a reduction in costly downtime during recovery.

Jan 1, 1993

By Gennaro G. Marino

Site conditions at several shallow room and pillar mines in Illinois are described and compared with the charac¬teristics of the subsidence profiles at the ground surface. The shape and magnitude of the subsidence profiles were found to be closely related to the thickness of the soil and rock over-burden the percent extraction of the coal, and the shape of mine pillars. The room and pillar mines were located at a shallow depth (from 112 to 220 ft), beneath flat to gently rolling terrain. Thickness of the coal seams ranged from 5 to 9 ft and at all sites was underlain by underclays. This information has been developed in order to improve techniques for evaluating the subsidence potential at sites within the Illinois coal basin. he results presented form a small portion of the work carried out by the University of Illinois with Illinois Abandoned Mined Lands Councils and the U. S. Bureau of Mines at the Minneapolis Research Center in Minnesota (Marino and Mahar, 1985). Presented in the paper are the modes of mine failures observed for Illinois room and pillar mines, an overall summary of the site geologic and mining condi¬tions, case histories of each mode of failure, a comparison of sag profiles, and then an empirical relationship between the site conditions and the maximum sag subsidence. The most ideal case histories are presented to illustrate fundamental behavior. A brief of the Paper is given in a summary and conclusions section.

Jan 1, 1984

By David J. Reddish

Longwall systems are inflexible in layout, intolerant of disruption and represent a substantial investment. It is therefore essential drat all understanding of the likely strata behaviour and support requirements is obtained prior to panel development. For many tears rock mechanics engineers have applied numerical modelling based kill finite element techniques to the design of the support and layout of underground excavations. Whilst such design methodology has worked well in civil engineering and hard rock situations, it has been less reliable when applied to excavation design in the soft rocks of the coal measures. This lack of reliability has been identified largely as being the result of the utilisation of unsatisfactory input data, This paper describes the results of an ongoing research programme at the University of Nottingham in which a novel rock mass rating system known as the UK Coal Mine Classification system was developed to enable the prediction of the strata properties that are required as input parameters for use in numerical modelling of the deformation of soft rocks around excavations such as roadways and longwall faces in coal mines. The paper describes the development of the system. the way in which classifications are applied to derive input data for numerical models and gives two case studies ill which deformations and stress re-distributions around coal mine excavations have been simulated by numerical modelling using the FLAC finite difference code.

Jan 1, 2000

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

Design and selection of support systems for longwall faces call for in-depth knowledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state-of-the-art datalogger system. The mechanised longwall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 K W DERD shearer. The datalogger system was capable of storing data simultaneously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build-up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

By Anthony Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

Jan 1, 2004

By Jinsheng Chen

Longwall mining-induced abutment loads on the surrounding coal pillars can be grouped into two categories in terms of the relative position of the coal pillars and the longwall face. They are the front and side abutment loads. Even though a lot of research and efforts have been made to study the nature and behavior of these longwall mining-induced abutment loads, their influence zones and magnitude are still not well defined and fully understood due to the complexity of geological conditions and the longwall muting-induced overburden strata movement. The uncertainty about the mining-induced abutment loads often forces consultants and mining engineers to employ a conservative approach in designing coal pillars and entry roof control plans. The problems with this approach are that: (a) it increases CM development¬longwall retreat footage ratio, (b) it decreases coal recovery, and (c) it increases !Ill' operating costs. However, a more liberal approach may create safety issues and result in loss of production. Therefore, the importance of accurately defining the influence zones and magnitude of the front and side abutment loads induced by longwall mining can never be over emphasized. The authors in this paper attempt to define the influence zones and discuss the magnitude of the longwall mining-induced abutment loads by analyzing the field data measured at RAG American Coal Company's longwall mines. In addition, the relationship between entry stability and the balance among roof/floor conditions, pillar design, and roof control plan is also briefly discussed.

Jan 1, 2002

By Michael Jenkins

This paper reviews the history of rock burst research in the Coeur d'Alene Mining District of northern Idaho over the last 30 years. Rock bursting is a problem because of a combination of geological factors in the region--complex structure, high horizontal stresses, and strong, brittle rock that readily stores strain energy. The Bureau of Mines has cooperated with industry to study rock burst phenomenon for many years. Early work focused on methods to mitigate bursting problems within the context of existing mining methods. In the 1970's, researchers began investigating methods for altering or controlling conditions that lead to rock bursts. These control measures become part of the stope development that precedes mining or are changes in the mining process itself. Although, researchers continue to develop microseismic techniques, the major research effort focuses on developing a new mining method to reduce the number and severity of rock bursts in order to improve safety and increase productivity in the Coeur d'Alene Mining District.

Jan 1, 1987

By A. W. Khair

This paper presents an analysis of ground movements recorded from longwall operations in the Northern Appalachian region in West Virginia. The site chosen for the investigation was selected due to varying heights of overburden and topography and was instrumented for both surface and subsurface measurements. The instrumentation areas consisted of two panels covering various sections with unique geologic and topographic features. Instrumentation included surveying monuments and shallow boreholes using an inclinometer for measuring horizontal strata displacements. Vertical strata deformation was monitored utilizing a unique design of the mechanical grouting method. Full length borehole profile extension was measured using Sondex displacement rings in the inclinometer installation. Subsurface displacements, i. e. caving zone, fractured zone, and highly deformed non-fractured zone were identified. The nature of surface disturbances with respect to varying geologic settings were compared, and an attempt was made to simulate final strata caving and bed separation using finite element analysis.

Jan 1, 1987

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

The challenge of planning to minimize interaction effects in multi-seam mining is compounded by the difficulties inherent in extrapolating essential geological and spatial data between sampling points. To predict the effects of ultra-close mining on lower seam entry stability, simulated mine openings were studied using finite element analysis and body loaded photoelastic models. Both symmetrical and unsymmetrical loading was used to represent stress fields generated under multi-seam conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Stability predictions require precise definitions of geologic and spatial data, which could not be accurately defined by interpolation between sampling points. To overcome this problem an expanded roof stability model, SESAME2, was developed to incorporate reliability concepts based on Monte Carlo sampling. The model was demonstrated in terms of variations of innerburden thickness using a case study.

Jan 1, 1994

By Robert B. Francini

Longwall mining and pipelines have coexisted since longwall mining was introduced into the United States. How the pipeline operator reacts to longwall mining under their line depends on many factors. This paper outlines the process the pipeline operator goes through to determine the appropriate response when their pipeline is being undermined. Typical mitigation procedures are reviewed. Finally, the paper looks at current design practices for new pipelines that are expected to be undermined during their lifetime.

Jan 1, 2011

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

By Peter Griesenbrock

In German underground coal mining mostly arch and some rectangular roadways are used in the development work. Due to its positive results from numerical and physical modeling techniques as well as good underground experiences, the numbers of rectangular roadways has increased significantly. Today the bolt support - independent of its cross-sectional shape - represents an undeniable support element. During the introduction of new bolt techniques a detailed investigation of the rock and support mechanical effectiveness of bolt support in roadways at all operation stages is of basic importance. This effectiveness can be predicted and verified using different simulation techniques. For the planning of rockbolted roadways two supplementary simulation techniques are presented in this paper. By combination of all available planning tools the best result for planning assurance can be achieved. Keywords: numerical modeling, physical modeling, arched roadway, rectangular roadway, roofbolting, advancing longwall.

Jan 1, 2002

By P. Forrest

Based on the results of mathematical analysis, photoelastic modelling, and case studies, the mechanisms of longwall under- mining interaction has been thoroughly investigated. The effects of using yield pillars in combination with rigid pillars in lower seam mine design have been found to provide significant improvement in ground conditions during undermining. Off- setting of solemnized longwall panel entries relative to upper-seam remnant structures has proven to be effective in alleviating adverse stress conditions.

Jan 1, 1988

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By Daniel W. H. Su

A floor-bearing capacity test apparatus was designed and constructed to determine the true bearing capacity of soft floor materials beneath coal pillars or longwall face supports. The apparatus has been employed in entries up to eleven feet in height. Results of in-mine floor-bearing capacity tests suggested that the ratio of the soft fireclay thickness to the bearing plate width and the moisture content in the fireclay were the most critical parameters affecting the ultimate bearing capacity. Foundation engineering principles were applied to interpret the field test results to estimate the floor-bearing capacity beneath longwall face supports.

Jan 1, 1993