Search Documents

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987

By E. J. Beckman, R. M. Enick, C. Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic platinum group metal complexes from an aqueous phase. However, because conventional extractant-metal complexes are not soluble in liquid carbon dioxide, this can be achieved only if highly carbon dioxide-soluble extractants are developed. For example, trioctylamine-gold chloride is not soluble in liquid carbon dioxide, although trioctylamine is CO2 soluble. The novel CO2-soluble extractants presented in this paper have a CO2-philic fluorinated tail to enhance solubility and a conventional amine head group for extraction of metals. Both the extractant and the extractant-metal complex are soluble at ambient temperature at pressures from 7 to 35 MPa. Efficiency factors as high as 2.23 have been measured using 1,1,2-trichlorotrifluoroethane (TCTFE), a low pressure screening liquid for carbon dioxide, indicating that these compounds will strongly bind the metal chloride. For example, 84% of Pt-chloride was extracted into TCTFE using a 3.5:1 ratio of a double¬tailed fluoroalkyl amine extractant: metal chloride. An 88% recovery of Pt-chloride into high-pressure liquid carbon dioxide was achieved using the same extractant at a 3.5:1 ratio. Therefore, it appears possible to replace organic solvents with liquid carbon dioxide during the extraction of platinum chlorides if highly carbon dioxide-soluble extractants agents are employed.

Jan 1, 2002

By Elif Çevik

This study deals with the mineralogical-geochemical characteristics and the industrial usage of the olivine from the dunites that crop out on the west of the Topuk village (Orhaneli). Mineralogical compositions of non-altered dunite samples are averagely as: Olivine (>90%), serpentine (1-4 %), opaque minerals especially chromite, magnetite, pyrite (1-3 %), and secondary minerals as magnesite, chlorite (1-2 %). X-Ray Diffractograms of the dunite samples indicate that olivines are in forsterite (93 on an average) composition, and chlinochrysotile and lizardite accompany to the forsterite. Chemical analyses of the dunites show that MgO, SiO2, Fe-,03 and LOI contents vary from 40,99 to 50,2 %, 34,67 to 40,6 %, 6,8 tol3,7 %, 0,11 to 11,27 %, respectively. SE-TAT Mining Company states that the study area has 400.000.000 tonnes proved, 800.000.000 tonnes probable and totally 1.200.000.000 tonnes olivine reserve. Consequently, all studies indicate that Orhaneli Olivin has convenient mineralogical and chemical properties and the grain size (0.04-40 mm) for industrial usages such as abrasive, olivine sand products, steel slag conditioner, balast and covering material in industry: Orhaneli olivines are demanded especially from the firms related to refractory industry, iron-steel factories, naval forces and shipyards. SE-TAT Mining Company also exports these olivines to different countries such as Macedonian and Spain.

Jan 1, 2005

By Raj K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Canadian open-pit mines are highly mechanized and use state-of-the-art equipment and support technology. During the past few years, productivity improvements at Canadian open-pit mines have been achieved by taking advantage of larger equipment, in-pit crushing and conveying, truck dispatch systems and electronic management tools. The most recent developments are related to hydraulic transportation and the application of global positioning systems (GPS). Mine planning has become computerized. Environmental issues are dealt with in all phases of planning. Equipment modifications are pursued with vigor to keep the equipment functioning in the hostile Canadian north. In 1997, the mining and mineral processing sector employed 370,000 Canadians, contributing $26.2 billion to Canada's gross domestic product (GDP). The value of production of the Canadian mineral industry, including coal, amounted to $19.1 billion in 1997. Gold remained Canada's leading mineral with production valued at $2.8 billion. This was followed by copper ($2 billion), coal ($1.9 billion), zinc ($1.6 billion) and nickel ($1.9 billion). [ ] Synthetic crude oil from oil-sands mining operations in Alberta represents an important part of Canada's petroleum production. In 1997, the value of synthetic oil production was $2.87 billion. Canadian oil-sands mining has contributed significant technology developments in Canada.

Jan 1, 1999

By A. J. Getz

Major precious metals projects are underway in Australia, Papua New Guinea, Indonesia, the Philippines and New Zealand. This article reviews the status of those projects. Included in this review are project location, reserves, method of resource exploitation, anticipated production, and other unique conditions. The article is limited to major precious metals projects in the Western Pacific region. This is not meant to negate the attractiveness or importance of the many other projects in that area. The geographical setting of these five countries are shown in [Fig. 1]. The gold output of the countries has increased dramatically during the 1980s. [Table 1] compares 1980 and 1988 production figures. The compound growth rate is 120%. That reflects the attractiveness of the region’s resource base as well as the impact of price increases, new exploration models and processing technologies, and changes in government policies. If the 10 projects discussed here are all brought onstream, their combined output - at about 130 t (4.17 million oz) - would amount to an increase of greater than 50% over 1988 production from this region. Table 2 shows indicative production levels for each of the 10 projects. Dollar amounts are in US currency unless otherwise specified. Australian dollars have been converted to US dollars at the rate of 1.28: 1.00.

Jan 1, 1990

By Håkan Stille, Kjeld Boye-Møller, Lars Lundström

BACKGROUND Forsmark Power Station is a nuclear power plant under construction at the Baltic abt 120 km north of Stockholm. Investigations on the Site were started in 1969. Areas were reserved for a maximum of 6 units of which the buildings for two of them, Unit 1 and 2, were nearly finished in 1976, when the investigation for Unit [3], here presented, was carried out, cf Fig. 1. [ ]

Jan 1, 1979

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant' with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By Beverly Cramp

In 1995, mining engineer Alain Gachet thought about using Earth-observation satellite imagery to search for precious minerals. The latest radar Earth-observation satellite, Canada’s RADARSAT-1, had just been successfully launched at the time, creating new opportunities for commercial applications. Gachet was working in Congo Brazzaville as an oil executive and general secretary of Elf Congo for the French national oil company Elf Aquitaine. He understood that the RADARSAT-1 launch promised new and cost-effective sources of data for mineral and oil exploration. “It was early 1996 before I ordered my firstRADARSAT-1 satellite images,” said Gachet. “I was first struck by the quantity of information delivered by the radar images. Linear structures and faults were clearly defined and subtle topographic features were tremendously enhanced,” he said. “It was ‘tree top geology,’ but this kind of information appeared to be key for finding new gold seams.”

Jan 1, 2003

By Walter Hoecker

The dissolution of gold in cyanide_ leaching has been we11 published with the genera1 acceptance that gold is oxidised by oxygen and stabilized by complexation with cyanide [1]. The dissolution of gold is essentially an electrochemical process. The rate of the anodic gold dissolution is controlled by the cyanide concentration. - (2) While the cathode reduction of oxygen is controlled by dissolved oxygen concentration - (3) There are a number of factors influencing the concentration of oxygen, and if 1owered substanth.lly will effect the efficiency of the leaching plant. These include: "' salinity "' temperature "'partial pressure "'oxygen consumption rate The use of pure oxygen for· cyanidation is only beneficial if oxygen is rate limiting, Conversely a slurry saturated with air (typically 5 - 8 ppm) may not be enough for maximum leach rate. The diagram below shows the maximum dissolved oxygen levels obtainable with pure oxygen and air. DISSOLVED OXYGEN (MAXIMUM) IN WATER At steady state, the rate of the cathodic reaction must equal the rate of the anodic reaction. Thus the rate of gold dissolution is dependent on both the· cyanide and oxygen concentrations. - (4) Using an average of Do/Den =· 1.5 [2] (where Do and Den are the oxygen and cyanide diffusion coefficients) the table below illustrates the maximum effective oxygen concentrations for given cyanide levels in clean water [3].

Jan 1, 1992

By B. A. Kuyper

The Cove gold-silver deposit is located 50 km southwest of Battle Mountain, Nevada and 1.5 km northeast of the McCoy Mine. Total proven and probable reserves are 48.7 Mt (53.7 Mst) with an average grade of 1.85 g/t (0.054 oz/st) Au and 87.1 g/t (2.54 oz/st) Ag. Mineralization is hosted by Triassic carbonate and siliciclastic rocks in two separate orebodies. Oxide ore consists of disseminated gold and silver in clay-altered, manganese-flooded limestone. Sulfide ore is dominated by pyrite-sphalerite-galena veins in siliciclastic rocks and sandy dolomite. Gold and silver occur in the native state, associated with the base metal sulfides. Mineralization is interpreted to be the distal expression of a porphyry system. The McCoy gold (copper) deposit is interpreted to be the proximal expression of the same system.

Jan 1, 1991

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By Sam S. Arentz

Storm King Mines began with the concept that the resource potential of thick and steeply pitching seams of the Grand Hogback region of Colorado could be mined profitably. Two large tracts of private land (fee coal) were acquired; approximately 23.8 km2 near Glenwood and 16.2 km2 near Meeker. Figure 1. Although both properties have substantial coal reserves, one has several distinct advantages in developing a competitive mining operation. Table 1 illustrates these advantages. Among the most important considerations from an economical point of view are proximity to railroad, highway, labor force, quality of coal, seam thickness, and source of water. As can be seen, Storm King Mines' property is adjacent to the main line of the D & RGW Railroad, 1-70, and the Colorado River. The cities of New Castle, Glenwood Springs, Silt, Rifle, Carbondale, and Parachute are within short commuting distances and have available skilled labor.

Jan 1, 1983

By Yi Yang, CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU

Steel slag is an industrial byproduct of steelmaking that is mainly composed of calcium, iron, silicon and magnesium. In addition, depending on the different raw materials entering the furnace, steel slag contains a certain amount of vanadium that is the main source of vanadium production, accounting for 69 percent of the species of the total vanadium raw material [1]. From experience, the production of one ton of steel will generate 1.0 to 1.5 tons of steel slag [2]. However, the utilization efficiency of steel slag is less than 30 percent, and a large amount of steel slag is identified as waste and stacked in tailings. The random stacking of steel slag not only wastes large amounts of limited steel and land resources but also exerts pressure on the environment [3], making it imperative to research the effective utilization of steel slag and recycling of metal resources.

By Stephen P. Mulqueen

Searles Lake is an evaporite basin located near the community of Trona in northwestern San Bernardino County, CA. Searles Valley Minerals Operations Inc. (SVM), a subsidiary of Nirma Limited, currently manufactures more than 1.58 Mt/a (1.75 million stpy) of industrial minerals from natural brines produced from several lakebeds within the basin. The chemical manufacturing facilities in Searles Valley represent extremely complex operations involving solution mining and mineral extraction processes.

Jan 1, 2012

By Dennis Ofiara, Michael Lewis

An experimental 1.75 meter Shaft Boring Machine was designed and manufactured by The Robbins Company. The drill was used by contractor Drillcon Raise AB to drill test shafts at an SKB underground test facility. SKB is the Swedish authority responsible for safe management of nuclear waste materials. This “SBM1.8” Shaft Boring Machine was used to drill shallow test shafts ingranitic rock at SKB’s Aspo underground laboratory. The drill used a unique vacuum mucking system. The bored shafts were held to very strict tolerances for bore diameter, straightness, and verticality. This drill was launched and operated from a mobile launcher. Headroom and working space were limited. The SBM1.8 drill produced acceptable test holes. SKB will carry out several studies to determine the suitability of this geology, and of this technique, for safe nuclear disposal. In addition to future use at SKB, many applications are foreseen, particularly in the civil construction industry.

Jan 1, 2005

The market for titanium feedstocks (ilmenite, rutile,synthetic rutile and slag) is driven primarily by offtake from the titanium dioxide (TiO2) pigment industry. The pigment sector depends on the performance of the global economy. Titanium sponge is the first stage of titanium metal manufacture. It constitutes a minor component (3 percent) of overall demand for titanium feed-stocks. Production and consumption TiO2 pigment consumption in 2004 was estimated to be 4.63 Mt (5.1 million st), up 7.6 percent from 2003. It was driven by strong demand in most regions. In the United States, apparent TiO2 pigment consumption rebounded by 5.4 percent (highest growth rate since 1997) to an estimated 1.12 Mt (1.23 million st), following the decrease in demand during 2003. Chinese TiO2 pigment consumption continued its strong upward trend, increasing by 10 percent to 598 kt (659,000 st) in 2004.

Jan 1, 2005

By S. M. Cohen

Roll crushers had been used in the past ahead of existing milling systems in order to obtain additional production from such mills in both the mining and the cement industries. Historically, a roll crusher as a preliminator to a ball mill has been used for a number of industrial mineral applications. Flowsheets, from Taggars(1) show systems for fluorspar, graphite, lead and zinc to name a few, which are shown in Figures 1 to 4. These units applied, (in some cases still in service), prior to 1950 and as early as the 1920's, were of two general types, rigid rolls and spring rolls. The rigid rolls were phased out in favor of the spring rolls. The spring force related to the linear inch width of the rolls, ranged from 500 to 50,000 lbs/linear inch(1) on units up to 90" diameter. With choke feeding, the rolls were spread against the spring force during crushing keeping the system under high pressure to obtain high effectiveness.

Jan 1, 1986