Search Documents

What is the preferred electrolytic cell design and why? Hall: Considerable research remains to be done on electrolytic cell design. Studies are presently being conducted to determine optimum voltage and amperage. Zadra cells, which were used in some of the first carbon plants, are efficient when properly installed. Gold and silver are deposited on large-capacity, cylindrical steel wool cathodes. At times high value sludge falls from the cathode to the bottom of the cell. Rectangular cells, which were developed at some smaller operations in Nevada, require less floor space and have some desirable features in that cathodes can be moved and sludge can be removed from cell bottoms without actually shutting down the circuit. In South Africa two types of cells using graphite and diaphragm configurations are being tested. Duncan: The rectangular cell has one problem it's easy for shortcircuiting to occur. If you don't have a good seal on the side of the tank and on the bottom, the solution is going to want to flow around the bottom and sides of the cathodes and you're going to get poor performance in the cell. That is the advantage the Zadra cell has over the rectangular cell. With good sealing, which is a must, you should be able to get a ratio of the value of the solution going in to the value of the solution coming out of 10 to 1. Ken, can you tell me what you're attaining on the Zadra? Hall: At the Homestake gold operation in Lead, the cathode in the No. 1 electrowinning cell is loaded to about 600 ounces when it is moved to the refinery. At this time the No. 2 cathode is moved to the No. 1 cell. The No. 3 cathode is moved to the No. 2 cell and a cathode with new steel wool is placed in the No. 3 cell. In rectangular cells this sometimes is not possible because the loading on the cathode in the last cell may be as high as that in the No. 1 cell. As Don has pointed out this can probably be prevented by good seal design between cathodes. Potter: At the risk of sounding as though I'm straddling the fence, I really believe that either the round cell, as developed by Jack Zadra, or the rectangular cell will do an acceptable job. The Zadra is a fine unit. Leaks are not unknown but there are not very many. However, the rectangular cell is very saving of floor space. Plastics have been greatly improved during the past year or two and there is a very efficient design for the rectangular cell. It would have six cathodes in it and contain about 25 ft of steel wool. The body of this rectangular cell would be reinforced fiberglass plastic but with an integral lining of a high temperature plastic. I think either cell is so efficient and reliable that I would almost be tempted to flip a coin depending on floor space requirements. Either cell can be used to pull a loaded cathode and to advance the lesser loaded cathodes. Don, what is the configuration of your cell? Duncan: The Pinson rectangular cell has dimensions 2 ft wide, 30 in deep, and 10 ft long-long enough to take a dozen cathodes and anodes. We are currently using six of each but are not up to full capacity as yet. It's a steel tank coated with rubber. We have copper bus bars, which brings to mind that the last cathode in the tank, in one instance, was loaded heavier than the first one. That was probably a function of poor contact between cathodes and the bus bar. You can have erosion of the bus bar and if you don't get current flowing into the anode and out of the cathode, the cells will not function properly. Kappes: Just a few comments on cell design. In an alcohol stripping circuit we are running in Beatty„ NV, we are using PVC pipes for all circuitry piping and a commercial polypropylene electrolytic cell. They seem to be working quite nicely. The cell itself has eight cathodes measuring 18 in2. At six gallons per minute flow into the cell, at an average gold content of about 500 ppm, we seem to get good loading on the first three to four cathodes and not much on the end cathodes. At 12 gallons a minute flow we seem to be seeing gold uniformly along all eight cathodes. We are running at quite a high amperage level, about 400 amps into that cell. Gene McClelland, US Bureau of Mines, Reno Research Center (from the floor): I was associated with a company where the packing density of their steel wool cathodes was much too high and created some short-circuiting problems in their electrowinning circuit. I would like to ask the panel if they can recommend a packing density for cathodes in pounds of steel wool per cubic foot. Hall: The weight of steel wool put on one of our cathodes is 10 lb and the dimensions of the cathode are such that density would be about 0.75 lb/ft3. Duncan: I made a rough calculation and I'm estimating about 2 lb/ft3. Potter: In checking over a number of electrowinning operations, I found apparently very satisfactory operation within the limits that have been mentioned. I have come to a figure of about 0.5-1.0 lb of medium grade steel wool per cubic foot packed as uniformly as possible, of course. One consideration in packing is the fact that there should be good contact between the steel wool and the conductor. Operators tend to compact the steel wool more than would be desirable just to try to maintain good contact.

Jan 10, 1981

By M. Grun, A. C. Marlowe, I. Littleford

SYNOPSIS A Wirth tunnel borer owned by Anglo American Corporation completed a 1150m long tunnel some years ago and was subsequently extensively modified by Technical Development Services. In 1982 this borer provided new and particularly interesting information In the field of hard rock boring. The abrasive quartzltes traversed proved to be a challenge to the cutter manufacturer and the project team. This paper examines the problems faced, the solutions found and the lessons learnt.

Jan 1, 1983

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By J. J. Schwoebel

Resource Enterprises, Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REI?s pilot project at the Soldier Canyon Mine, Carbon County, Utah, REI has drilled nearly 15,250 m of horizontal in- seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1986

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By B. Beatty

This is a response to M. J. Hrebar's paper, which tracks in detail the highly productive stripping capabilities of modern large bulldozers at two separate installations. It proves the old adage "economies of scale" and quantifies the advantage of being able to move large loads of dirt over comparatively short haul distances by sliding rather than carrying the load. This discussion examines whether a bulldozer is the most efficient way of using this geotechnical principle.

Jan 1, 1994

By S. G. Tough, H. J. Hignett

The Transport and Road Research Laboratory is carrying out tunneling trials at Chinnor, Oxfordshire, with a 5-m-diam, full-face tunneling machine. The work, which is for research purposes only, involves driving the tunneling machine through chalk with most of the physical characteristics of the machine and its power consumption closely monitered. At the Conference a film was shown about this work, illustrating both the tunnel construction and the research program.

Jan 1, 1974

By Dennis Ofiara, Paul Zick

Two 8.2 m diameter flood control tunnels are being constructed in the Taylor Shale Formation beneath San Antonio, Texas. These tunnels use precast concrete segments as final lining. This paper describes the features of the segments chosen for this project. The tunnels are being excavated with a hybrid Tunnel Boring Machine. This paper also describes the features of the TBM which make the machine compatible to the type of segments chosen.

Jan 1, 1989

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By Keh-Jian Shou

"This study adopts and analyzed a shield tunneling case in Taiwan, with a diameter from 5.25m to 6.70m and the smallest radius of curvature 100m, which was constructed in gravel formations as well as a vibration sensitive area. In this case study, a vibration monitoring plan, comprising the sensors inside the shield machine and on the surface, was proposed and performed to provide the vibration data during the construction. In this project, the major vibration reduction considerations were increasing the open ratio of the cutter head (to reduce the cutting function) and reducing the rotational speed of the cutter head. The results of the construction suggest the appropriateness of the above considerations. The findings could provide suggestions to the other similar shield tunneling cases. INTRODUCTION Underground vibrations during shield tunneling are typically isolated and absorbed by the soil. However, a portion of these vibrations may disseminate to the surface. These vibrations are considered micro-vibrations, which generally do not pose a threat to surface structures, and are thus seldom the focus of research. The present project was located in the Hsinchu Science Park where shield excavation bypassed numerous high technology manufacturing plants (e.g., wafer manufacturing plants). The vibrations generated by shield tunneling may affect the vibration-sensitive manufacturing equipment and instruments in these plants, and induce problems in manufacturing processes. Therefore, research to comprehensively understand the characteristics and potential influence of such vibrations is essential. To clarify the characteristics and potential influences of vibrations generated during shield tunneling, the vibration level in the excavation of the Taoyuan International Airport Access (TIAA) Metropolitan Rapid Transit (MRT) Project was examined, as it possesses similar excavation conditions to the present project. The parameters collected from relevant tests were provided as a reference to the firms along the excavation route of the present project to explain the effects of vibrations, and to relevant units for shield machine selection and project execution. No yield problems resulting from shield machine induced vibrations were reported by the firms, and the vibration levels measured in the present project were comparatively lower than those in the TIAA MRT Project. Because the related literature is scarce, this study aims to analyze the collected measurement data and provide suggestions on shield machine selection or designs. Such that we can more properly evaluate and control the impact of shield tunneling induced vibrations in similar projects."

Jan 1, 2016

By Majid Sadeghi, Ali Naghi Dehghan, Kaveh Ahangari, Seyed Mahdi Pourhashemi

"Instrumentation and monitoring of ground deformations in tunneling is a principal means for selecting and controlling the excavation and support methods among those foreseen in the design, for ensuring safety during tunnel construction (including personnel safety inside the tunnel and safety of structures located at ground surface) and, finally, for ensuring construction quality management. In this paper, the effect of Hakim Tunnel excavation on the behavior of the surrounding ground was investigated based on the geotechnical instrumentation. This tunnel with 1080 m length, 18 m width and 12.6 m height is being constructed using the SEM/NATM along the Hakim Highway in Tehran. The results which are obtained from recorded displacements by geodetic pins (on the tunnel wall and roof), extensometers and settlements pins (at the ground surface) demonstrate the tunnel stability during the various stages of excavation. However, it is concluded that the rate of excavation in different sequences could have a major role on stability of tunnel. In this case the surface and underground openings were monitored as well as needed for controlling the face probably collapse. INTRODUCTION Tunneling is increasingly being used world-wide to provide the infrastructure required for sustainable urban areas. The high demand for space and the disturbance of existing infrastructures by construction measures increasingly forces future infrastructure projects to be conducted underground. One of the important purposes of tunneling projects in urban area is not only to minimize displacements but also to control them during the construction (Pourhashemi et al., 2015). Normal method of tunnel stability analysis is not able to evaluate the real rock and soil mass behavior. Hence, instrumentation is a practical method to monitor displacements, to evaluate the stability of underground openings, and also to determine the rock and soil mass properties (Dehghan et al., 2012. Dehghan, 2013). Rocks and soils are materials with properties that can change instantly and significantly from one point to the next. Some complications may often happen due to uncertainties in the loads that the new facility must withstand during construction and operation. Instrumentation and monitoring provide quantitative information on actual behavior of ground and adjacent structures. A lot of deformation monitoring studies for determining and analyzing different kinds of engineering structures such as tunnels, bridges, high-rise buildings and dams are implemented. Considering the type of the structure, its environmental"

Jan 1, 2016

By K. A. Natarajan, Abha Kumari

"The effect of applied DC potentials on the bioleaching of a chalcopyrite concentrate in the presence of Acidithiobacillus ferrooxidans is discussed. Copper dissolution was the highest at an applied potential of +600mV (SCE), while all the dissolved copper got cathodically deposited at a negative potential of -600mV (SCE). Electrobioleaching at an applied potential of +600mV (SCE) was established at different pulp densities as a function of time. The effect of applied potentials and electrolytic currents on the activity and growth of bacterial cells was assessed. Preadaptation of bacterial cells to the concentrate slurry and electrolytic growth conditions significantly enhanced copper dissolution. Electrochemical and biochemical mechanisms involved in electrobioleaching are illustrated with respect to oxidative dissolution and biocatalysis of anodic oxidation. IntroductionIn recent years, the bioleaching of low-grade chalcopyrite ores as well as their flotation concentrates has been receiving increased attention. Use of mesophilic bacteria such as Acidithiobacillus ferrooxidans in the bioleaching of chalcopyrite does not yield desirable copper extraction rates due to its easy passivation.Bioleaching of chalcopyrite using A. ferrooxidans has been reported to be very inefficient, and use of thermophilic bacteria at higher temperatures is recommended to improve its bioleaching rates. Bioleaching under imposed applied DC potentials or currents has been shown to enhance not only bioleaching kinetics but also to confer selectivity in mineral dissolution (Abhakumari, 1996; Chirpa Selvi and Natarajan, 1998; Natarajan, 1992a, b,c). Electrochemical principles governing electrobioleaching have been earlier illustrated (Jyothi et.al, 1989). The role of applied potentials on the activity and growth of A. ferrooxidans has also been studied (Natarajan, 1992b). Also, the electrochemical aspects of bioleaching of several sulfide minerals when present alone or in binary and ternary combinations have been reported (Jyothi et al., 1989). The electroleaching of copper-nickel concentrate (Natarajan et al., 1985) and electrobioleaching of sphalerite concentrates have already been studied (Selvi et al.,1998). However, it is possible to enhance the bioleaching rate of chalcopyrite in the presence of A. ferrooxidans under galvanic conditions in the presence of nobler minerals such as pyrite (Jyothi et al.,1989). Also, dissolution of chalcopyrite can be significantly enhanced under applied potential conditions. Ali Ahmadi and his coworkers recently studied the electrochemical bioleaching of chalcopyrite concentrates using moderate thermophiles (Ahmadi et al., 2010, 2011)."

Jan 1, 2015

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By M. U. Khan, A. D. S. Gillies

"Diesel exhaust is a major cause of large number of occupational diseases. Acute and continuous exposure to Diesel Particulate Matter (DPM) can cause numerous health issues including respiratory disease, reduced lung capacity, heart disease etc. The National Institute of Occupational Safety and Health (NIOSH) and the International Agency for Research on Cancer (IARC) consider diesel engine exhaust as carcinogenic. In large underground metal and nonmetal mining operations, regulatory compliance regarding miner’s exposure to airborne particles especially DPM is a big challenge. Complex mine networks add more difficulties in controlling DPM. MSHA relies on the NIOSH 5040 method for DPM compliance. The NIOSH 5040 method is a shift average based method which inherits some limitations. Due to these inherent limitations of the NIOSH 5040 method the concept of real-time DPM monitoring is promoted in the mining industry. Several real-time DPM monitors have been used by the researchers and efforts still continues to improve their measuring techniques and understanding. Real-time monitoring of DPM is vital to gain understanding of rapid changes in the mine atmosphere. The current study highlights the advancement in real-time DPM monitoring and mainly covers a review of several studies in which DPM concentrations were measured by utilizing real-time DPM monitors. INTRODUCTION Ventilation of underground mines is an important aspect of mining operations. Mining is a continuous activity and the ventilation networks in modern mines change with extended developments. Proper understanding of the ventilation network is a key design factor of an optimum mine ventilation plan. An important task of underground mine ventilation engineers is to provide clean air with sufficient quantity to the underground miners (Khan M. U. and Gillies A.D.S. 2015). The amount of fresh air supplied to the mine should be adequate to dilute the concentrations of contaminants present in the mine atmosphere. In the United States it is estimated that diesel powered equipment is used in thousands of mining operations (Stephenson D. J. et al. 2006). Use of diesel powered equipment is an attractive option in underground mines due to its several advantages over other available alternates. Diesel engines are rugged, dependable and fuel efficient (McKinnon 1999). It is common for diesel engines in heavy duty trucks to have a life of 1.6 million kilometers (McKinnon 1999). Looking at the developments in other energy alternatives, it can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment (Anon 2001). DPM is an important source of mine air contamination in many non-gassy underground mines (Khan M. U. and Gillies A.D.S. 2015). Diesel exhaust is harmful for humans. Acute and continuous exposure to diesel exhaust concentrations can cause several health issues. Some of the health diseases caused by DPM exposure are respiratory diseases, reduced lung capacity, heart disease, and lung cancer (National Research Council. 1981, Mine Safety. 2005). In addition, NIOSH regards diesel exhaust as “potential carcinogen” (Centers for Disease Control 1988) and IARC has declared that “diesel engine exhaust is carcinogenic to humans” (IARC 2012). NIOSH has also declared that the reductions in DPM exposure would reduce cancer risks (Centers for Disease Control 1988)."

Jan 1, 2016

By Patrick J. Maessen, Bart H. M. Hendrix

"In the Netherlands, the Dutch Tunnel Standard has been developed for the execution of road tunnel projects. The Dutch Tunnel Standard is based on the Dutch Tunnel Law (WARVW) which sets the minimum safety standard for road tunnels in the Netherlands. Uniformity of tunnels and the uniform perception of a tunnel by its users leads to a higher safety level. Therefore, several items in the Dutch Tunnel Standard are specifically developed to ensure safety in emergency situations through the plane of human factors. Taking human factors into account is important in regular traffic situations, but in an emergency situation, this can be vital. In this paper, the development and contents of the Dutch Tunnel Standard are explained in the first part and in the second part, the systems related to human factors are described. DUTCH TUNNEL LAW AND THE NEED FOR THE DUTCH TUNNEL STANDARD In the 90’s of last century and the early 2000’s, several serious accidents occurred in tunnels in Europe. These accidents involved fire and led to many casualties. After these accidents, the European Union decided to change the regulations for tunnel safety, leading to the EU directive 2004/54/EG. The primary goal of this directive is, that casualties are minimized in case of a calamity in a tunnel (e.g. fire). In the Netherlands, the EU directive led to the development of the tunnel law and a tunnel regulation (in 2006) to prescribe the safety features required for a safe tunnel. The new Dutch tunnel law – cited in the Building Act – was meant to make tunnel design easier – but resulted at first in the opposite effect. Tunnel design in the Netherlands and design standards of Rijkswaterstaat Rijkswaterstaat – the executing organisation of the Dutch Ministry of Infrastructure and the Environment – is the owner of the tunnels in the Dutch national motorway network, thus owner of the majority of the road tunnels in the Netherlands. In the early years of tunnel building in the Dutch national highway network (approximately 1950 – 1970), Rijkswaterstaat was not only owner, but also designer of its own assets. Most Dutch tunnels are submersed tunnels, because these type of tunnels provide a cost-effective way to make river crossings. Another type of tunnel that is used, is a TBM tunnel. Because of the geological conditions in the Netherlands (merely clay/peat and sand), there are no NATM or drill-and-blast tunnels in the Netherlands. Since the last decades, land tunnels (covered roads) are becoming more common to provide for multiple use of surface space and to meet more modern environmental regulations as traffic increases near densely populated areas. Tunnel lengths in the Netherlands vary from 500 m to 1.5 km for river crossings up to 6 km for the Western Scheldt (bored) tunnel. The lengths of land tunnels vary from 500 m up to 3 km. With these increasing lengths, some safety topics and design topics arise, topics that were non-issues in the past, when tunnels were only used as river crossings."

Jan 1, 2016

By J. Burrows

The Chamber of Mines of South Africa is an association of major mining corporations, gold mines, coal mines, diamond mines and other metalliferous mines. It looks after those interests of its members which can best be handled on a co-operative basis. The Chamber's activities include the engagement of labour; the negotiations of all labour matters, including minimum wage rates, with recognised trade unions and associations; the carrying out of advanced technological research; representing the industry in dealings with the government and the administration of miners' training colleges and rescue training stations. Subsidiary companies of the Chamber handle matters such as the refining of gold and other metals; the processing and marketing of uranium and the marketing of Krugerrands. The thirty-two gold mines members of the Chamber of Mines of South Africa produce approximately 694 tons of gold per annum. To achieve this they employ 430000 persons and break about 8400 kilotons of rock per month. The working revenue is approximately 4 225 million US dollars per annum and the annual working profit is approximately 2 050 million US dollars. The electric power consumed by the gold mining industry is 1650 MW, about 20% of the total power produced in South Africa, and the annual costs of this power is approximately 200 million US dollars per annum. It is estimated that about 25% of this power is used for ventilation and refrigeration appliances. Thus the annual power costs for ventilation and refrigeration is approximately 50 million US dollars. The gold bearing reef is a narrow tabular deposit situated at varying depths throughout the gold fields. The weighted mean rock breaking depths and, virgin rock temperatures range from 1 700 - 9 000 ft (520 - 2 740 m) and 68 - 113°F (20 - 45°C) respectively. The maximum virgin rock temperature at which mining currently takes place is 130°F (54.5 C). Obviously at such depths and temperatures and with such a large labour force the provision of an acceptable environment is critical and to achieve this 59 000 000 cfm (28 000 m3/s) of air is downcasted during the main shift and 122500 tons (430 MW) of refrigeration are provided. Legislation in South Africa requires that on metalliferous mines when more than 1000 persons are employed underground during any one shift the manager shall appoint one or more ventilation officers. The legal responsibilities of the ventilation officers are concerned mainly with the measurement and control of dust. In practice, this is not the main part of their work and ventilation personnel perform many other duties such as measuring and controlling the distribution of air, checking the performance of fans and cooling plants, planning air and refrigeration requirements and, more recently, measuring and controlling noise and illumination levels. Ventilation personnel are specialists who provide management with advice on all matters relating to the mine environment. At the present time there are 506 persons engaged as ventilation personnel in gold mines and a further 1744 persons are employed in gold mine ventilation departments in a non-technical capacity, for example as construction workers, filter cleaners, fire patrollers, etc.

Jan 1, 1980