Search Documents

By K. Wu, L. Li, D. W. Zhou, J. W. Yu

The presence of a fractured water-conducting zone (FWCZ) is of significant importance for the safety of underground mining under water bodies. When a coal mining area is covered with a thick layer of alluvial soil, the height, width, and distribution pattern of the FWCZ in the area shows unique features. The internal mechanism by which thick alluvial soil affects the FWCZ is still unknown. Using the Huainan coal mining area (HCMA) in China as a case study, we investigated the impact of thick alluvial soil on the height, width, and distribution pattern of the FWCZ through numerical simulation using the distinct element method, theoretical derivation, and data validation. The results indicate that a thick layer of alluvial soil inhibits the FWCZ height and increases the FWCZ lateral width. When the soil-to-rock ratio is greater than a certain value (the numerical result in this study is 15:18), the FWCZ height and width are affected by the thick alluvium significantly, and the thick alluvial soil alters the shape of the FWCZ from tall and thin to short and wide. The load exerted by the alluvial soil transfers downward to influence the FWCZ; however, this process is obstructed by the hard strata in the bedrock. Therefore, the vertical and lateral change trends show a similar step pattern. Our results can provide a basis for accurate calculation of the FWCZ height in mining areas with thick alluvial soil, to mitigate mine water hazards and increase the safety of underground mining in coal mines covered with a thick alluvium layer. Moreover, reducing the FWCZ height can help extend the upper extraction limit in coal mines covered with a thick alluvium layer, which reduces the thickness of the impermeable coal pillar and increases coal production.

Jan 1, 2016

By C. Birch, J. Perold

"Due to the challenging geological environment of the Postmasburg Manganese Field (PMF), a study was conducted to determine if any benefits would derive from the inclusion of resistivity data during threedimensional (3D) modelling of the manganese resource. This was achieved by estimating manganese resources from 2011/2012 drilling data and comparing them with manganese resources estimated from the same drilling data and resistivity data collected during 2013 and 2017.Both models were adjusted to limit their extent to the same 3D modelling space. Significant volume and tonnage differences were observed for all lithological units. The greatest differences were noted in the manganiferous zones of alteration – 7.200 Mt for the geological model versus 3.700 Mt for the geoelectric model.This study showed that the inclusion of resistivity data can reduce exploration costs significantly, as a direct consequence of the resistivity data allowing more accurate siting of boreholes. This decreases the number of boreholes, samples, and analyses required due to the 3D electrical delineation of mineralized areas prior to drilling.An additional benefit is the ability to more correctly forecast the net present value of an operation due to more accurate estimation of manganese resources and stripping ratios. This is clearly demonstrated by the estimated gross profit estimation of R409 million for the geological resource model versus R264 million for the geoelectric resource model.The addition of resistivity data can, therefore, reduce exploration costs and can increase confidence in geological and financial modelling. It would be reasonable to conclude that this approach could also be used for karsthosted massive sulphide deposits. IntroductionAccording to Corathers (2014) and Gajigo, Mutambatsere. and Adjei (2011), South Africa holds between 75–80% of global manganese reserves, followed by Ukraine (10%), Australia (3%), India (3%), and Gabon (2%). The known, land-based, manganese resources located elsewhere are estimated at 2%.The majority of economically important sedimentary manganese ore deposits in South Africa are situated in the Northern Cape Province (Gutzmer, 1996). Manganese ores of the Postmasburg Manganese Field (PMF) were discovered in 1922, and the Kalahari Manganese Field (KMF) in 1940. According to Astrup and Tsikos (1998) and Gutzmer (1996), mining of manganese ore from the PMF ceased during 1989 in favour of the superior quality of manganese ore from the KMF."

Mar 1, 2019

By L. M. Tavares, T. M. Campos, P. M. Faria, R. M. Carvalho

Recent advances in mechanistic ball mill modelling are expected to allow for more accurate predictions that overcome the well-known limitations of phenomenological approaches, including their inability to predict the effect of liner geometry and their wear, in grinding. Although able to describe continuous operation, the UFRJ model of ball mills has only been validated in the past in mills that operate in batch mode, either in laboratory or pilot scale. The present work demonstrates the application of the mechanistic UFRJ ball mill model to predict fine grinding of iron ore in a pelletising plant in Brazil, the first application of such a mechanistic modelling in continuous mode. It shows that the model provides accurate descriptions of flows after iterations in a closed-circuit with hydrocyclones. Keywords: Ball mill, iron ore, grinding, modelling, particle breakage

Jan 1, 2020

By A. P. I. Popoola, D. O. Okanigbe

Copper smelter dust (CSD) is a byproduct of copper smelting and is composed of considerable amounts of copper values and also contaminants (like silica and mullite). Silica in CSD forms Siloxane, a low density material, which is difficult to separate from the aqueous phase during solvent extraction. The need therefore arises to reduce/remove the aluminosilicates for better grade and recovery of copper in subsequent processes. This paper reports the use of two types of centrifugal gravity concentrators, namely Knelson (KGC) and Falcon (FGC), for upgrade of copper in CSD. The aim was achieved by an initial characterisation (Particle Size Distribution (PSD) and mineralogical analysis), together with Density Separation (DS) experimentation, premised on a hypothetical density difference between copper oxide and silicon/aluminum oxide. Wet screening results showed that 88.52 % of CSD particles were in -53 μm fraction. Further PSD study using laser diffraction showed the -53 μm fraction to be composed mainly of 26 μm, 22 μm and 18.5 μm fractions. Mineralogical analysis showed copper to occur mainly as oxides (24.34 wt%), but also as sulphides (7.95 wt%), and a substantial amount of aluminosilicates (42.97 wt%) were identified. Density of CSD was determined as 2.83 g/cm3. Copper content (18.02 wt%) in CSD was upgraded to 35.94 wt% in concentrate using KGC. In conclusion, the results showed good convergence between hypothesis and experiment. Additionally, it was also concluded that KGC performed better than FGC for copper upgrade in CSD. However, roasting CSD prior density separation was recommended for enhanced copper upgrade. Keywords: Copper smelter dust, density separation, solvent extraction, mineralogy

Jan 1, 2020

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By T. Wajima

Recovery of precious metals from hydrochloric solution using sulfur-impregnated carbonaceous adsorbent was examined. Sulfur-impregnated adsorbent with adsorption abilities of precious metals can be prepared from activated carbon using pyrolysis at 600 oC under 10 % H2S gas flow, and the adsorbed Au and Pd were precipitated as metal phase on the surface of the adsorbent. The adsorbents after precious metals adsorption were burned at 700 oC to obtain the residue mainly containing precious metals. The adsorbent was found to be highly efficient and selective for the uptake of precious metals, especially Au, in the presence of excess base metal ions from simulated spent automotive catalyst eluted solution using a column pack test. Keywords: Gold, platinum, palladium, reduction precipitation

Jan 1, 2020

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By R. J. Durrheim, B. Manzunzu, V. Midzi

Selecting ground motion prediction models (GMPM) is crucial in assessing seismic hazard levels in a specific region. This study investigates the influence of ground motion model (GMM) selection on seismic hazard assessment in Johannesburg, South Africa. Most seismic events affecting Johannesburg are related to mining activities and water ingress into the underground mine voids. The most seismically active regions in South Africa include areas around Klerksdorp, Welkom, and Carletonville. These regions experience a significant number of earthquakes, with mining activities being a major factor contributing to seismic events. Ten ground motion prediction equations were selected from regions of similar tectonics setting and were assessed to see if they correspond to the available local data. Six of these were also compared to the ground motions produced by the earthquake of 14 August 2014, which occurred in the Orkney area, one of the mining areas in South Africa. Sensitivity analyses were also carried out to assess the influence of ground motion prediction equations (GMPE) on the seismic hazard of Johannesburg. The results indicate that the choice of GMPM significantly affects the estimation of seismic hazard levels in Johannesburg. Different GMM can lead to varying ground shaking intensity predictions, impacting risk assessments and engineering design considerations. The findings highlight the importance of carefully selecting appropriate GMM tailored to Johannesburg’s specific geological and tectonic characteristics. Understanding how different models perform in this region is essential for accurate seismic risk mitigation strategies.

Jan 12, 2025

By F. Roelofse, D. Grobler, and M. Purchase, C. Gauert, E. Kotze

Scandium is an important industrial metal for which demand is projected to increase in the future. Although many Sc deposits are secondary, Sc is scavenged by clinopyroxene during fractional crystallization of primary, mafic-ultramafic magmas. Sc may thus occur in sub-economic concentrations in mafic-ultramafic intrusions. In this work, we present new data on the concentration of Sc in the Bushveld Complex (BC) of South Africa. The eastern and western limbs of the BC are considered to be largely pristine, primary magmatic deposits, whereas the northern limb shows evidence of largescale, localized crustal contamination. Samples from the primary magmatic cumulates of the eastern limb, from the mineralized Flatreef of the northern limb, and from the crustal-contaminated Footwall Assimilation Zone (FAZ) of the Flatreef were analysed for Sc. Despite the FAZ containing abundant clinopyroxene, interpreted to have recrystallized from the original cumulates in the presence of melted sedimentary rocks, no significant differences are seen in the concentration of Sc compared to other cumulate rocks of the BC containing less-abundant clinopyroxene. The concentration of Sc in the analysed samples is mainly controlled by mineralogy, with anorthosites, chromitites, and harzburgites containing under 20 ppm, and norites and pyroxenites containing 20–40 ppm. The parapyroxenites of the FAZ are less enriched in Sc than expected, suggesting that Sc may have been lost during alteration and recrystallization.

Sep 1, 2022

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By B. Friedrich, A. Birich

Gold has been a metal of special importance for mankind for several thousand years. Its outstanding chemical resistance is an important property of this noble metal, but becomes a disadvantage when it comes to gold recovery. The established processes are based on highly aggressive and toxic reagents. Different alternative leaching reagents with a significantly lower toxicity proved to be promising alternatives in the last decades. Major research activities in this field focused on gold ores, so that leaching of secondary resources were not described sufficiently. Based on literature research and extensive experimental investigations, a reagent assessment was conducted for hydrometallurgical gold recovery from electronic waste. It was found that besides thiourea and halides, thiosulfate in particular represents an alternative of major relevance. A variety of different electronic waste (e-waste) specimens were investigated to identify suitable leaching conditions. As a result, an almost complete and selective gold recovery in less than 48 hours from different electronic waste types and components was achieved by thiosulfate leaching. Within the experiments conducted, it was found that the leaching behaviour of cyanide alternative lixiviants differ strongly from leaching of primary ores. Keywords: Gold leaching, cyanide alternative, thiosulfate, electronic waste

Jan 1, 2020

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By D. Kumar, B. Rai, S. G. Srinivasan, V. Jain

Chalcopyrite and pyrite are among the major gold bearing minerals in the world. The gold content in chalcopyrite and pyrite varies from 0.02 to 200 ppm and 0.01 to 20 ppm, respectively. Apart from gold, chalcopyrite is also the primary source of copper. Thus, the recovery of gold and copper are often associated with the recovery of chalcopyrite and pyrite. Flotation is one of the most successful methods applied to beneficiate chalcopyrite and pyrite. The success of a flotation process depends on an appropriate choice of the flotation collector used to achieve the desired selectivity. A thorough understanding of the atomic structure of the predominantly exposed mineral surfaces can immensely aid in developing highly selective collectors that can exploit both the physical and chemical characteristics of these surfaces. In the present study, density functional theory calculations within the plane wave framework are used to understand the surface structure and reconstruction of the most stable chalcopyrite (001), (100), (110) and (112) and most stable pyrite (100) surfaces. The chalcopyrite (001) and (100) metal-terminated surfaces undergo significant reconstruction and result in metal-metal bond formation in the sub-surface layer while the surface layer is replaced by S-atoms. On the other hand, the (001) and (100) S-terminated surfaces show S—S disulfide bond formation upon relaxation, which are consistent with literature reports. The chalcopyrite (110), (112) surfaces and pyrite (100) surface undergo rearrangement, but no reconstructions in terms of metal-metal or disulfide bond formation are observed on these surfaces. Keywords: DFT, surface reconstruction, pyrite, chalcopyrite, adsorption

Jan 1, 2020

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By J. E. Dickinson, R. Campbell, M. J. Cole, K. P. Galvin, M. C. Cole

It is common practice in the beneficiation of iron ore ultrafines to apply reverse flotation, and hence float the gangue minerals, leaving behind a high-grade iron ore product. Given the difficulty in floating particles finer than 20 μm, especially those finer than 10 μm, it is necessary to subject the feed to desliming ahead of flotation. There are two problems with this approach. Firstly, given the known inefficiencies of cyclones, desliming needs to be aggressively applied to particle sizes upwards of 45 μm to ensure all the offending ultrafine gangue is removed. Secondly, desliming also removes a significant portion of the valuable iron ore. Thus, a significant portion of the ultrafines, including the iron ore, is lost to the tailings. This paper examines the direct flotation of iron ore fines using the Reflux Flotation Cell. The RFC operates using a concentrated bubbly zone, in the absence of a conventional froth zone, for delivering strong counter current washing through an inverted fluidised bed of bubbles ahead of the product discharge. A system of parallel inclined channels in the lower part of the cell provides enhanced segregation of the bubbles from the tailings, preventing the loss of air bubbles into the tailings. Experiments conducted under semi-batch conditions produced encouraging results with concentrates of ~65% Fe grade in a single flotation stage. Comparatively, up to five successive batch flotation stages were required when using a laboratory scale batch mechanical flotation cell to achieve similar Fe grades. For a given grade, lower Fe recoveries were typically achieved by the RFC. This was attributed to the effective prevention of ultrafine particles succumbing to hydraulic entrainment under a positive bias flux, as well as an increasing feed volume involved in the semi-batch operation using inverted fluidisation water for cleaning. Overall, similar grade-recovery curves were produced, however, significantly higher grades were obtained by the RFC and with fewer separation stages. Keywords: Desliming flotation, iron ore, modified release analysis, reflux flotation cell

Jan 1, 2020

By L. Thomson

"The smelter at Sudbury Integrated Nickel Operations, located in Sudbury, Ontario, operates a single electric AC furnace. This furnace treats nickel sulphide concentrates produced by Glencore and third-party feeds and as such its performance is key to the company’s nickel supply chain. Currently the plant has two shutdowns per year in order to carry out significant repairs on matte tap-holes.Improved monitoring systems that enable better prediction of tap-hole wear have been a continued focus. The electric furnace is an essential piece of the smelter flow sheet requiring the need for planned tap-hole maintenance along with robust systems for management according to to this plan.The ability to meet our goal of zero harm is ensuring that safe practices are in place. Detailed procedures and cool-down practices have been implemented to ensure that required matte chemistry and temperature criteria can be met during the period leading into a shutdown for tapblock maintenance.A significant repair of the electric furnace will take place in 2015. During this rebuild, the sidewalls and matte endwall will be replaced. There is work underway to improve wall and matte end performance in an attempt to extend the time between rebuilds. This paper will review the approach taken towards this end."

Jan 1, 2014

By Ron Tluczek

[Power Point Presentation]

Jan 1, 2006

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By J. N. Van der Merwe

"Platinum is a highly valuable resource, its safe and economic extraction is paramount. The success of platinum mining by the bord and pillar method depends heavily on a comprehensive and dependable pillar design method. Pillars need to be large enough to safely support the load and small enough to avoid loss of resources. A critical evaluation of current pillar design systems used in narrow-reef platinum mining was undertaken using practical experience from a large feasibility-stage platinum exploration project, supplemented by observations from several platinum mines in Zimbabwe. An extensive literature survey was undertaken in order to determine the current status of design systems. Through this approach, the shortcomings of current pillar design systems are highlighted. Areas are proposed for further research to obtain a better understanding on how additional factors influence pillar system stability. The exploration work highlighted how rock mass classification methods can be utilized in determining the overall strength of pillars. Current pillar design systems for narrow-reef platinum mining consider width-to-heightratio (usually with different exponents for width and height) and the strength of the pillar material. However, there are many more important factors that are not considered and which have a bearing on pillar system stability. An in-depth study of these parameters with a view to establish effective narrow- reef platinum mining pillar design systems needs to be undertaken. IntroductionPillars have been used as a means of support since the early days of mining. Pillarsupported mining methods such as bord and pillar require a reliable design system for them to be successful. This paper presents an evaluation of the current hard-rock mining pillar design systems as applied to a practical large-scale narrow-reef platinum mining feasibility study. It is vital to have a dependable pillar design system for economic and sustainable mining. Using an extensive database collected from the project, the pillar strength formulae were tested and several discrepancies noted. This necessitates the establishment of more reliable pillar design systems. In narrow-reef platinum mining, large compressive stresses accompanied by geological and geotechnical factors contribute to pillar instability. A well-formulated pillar design system is required that accounts for such factors so as to minimize pillar failures."

Jan 1, 2017