Search Documents

By George F. Dana

Oil yields, lithology, and stratigraphy have been evaluated for 15 cored wells and two sampled wells representing 10 square miles of the Tipton Member of the Green River Formation near Green River, Wyo. The area evaluated is being used by the Bureau of Mines for experimental production of oil from the oil shales in place. Lithology and oil yields were correlated to produce a stratigraphy diagram for the in situ study area, permitting precise designation of comparable sections. Because of lateral uniformity of oil shale, oil yields from eight cores and two sets of drill-cutting samples within a quarter section show the range of variation in average oil yield arising from experimental error. Variation in average oil yields from the seven cores representing the 10-square-mile study area lies within the expected experimental error. No difference in oil-shale richness across the study area is indicated. Average oil yields for three Tipton sections in the study area were deter-mined as follows: (1) The entire Tipton Member oil shale (about 145 feet thick), 13.3 gallons per ton; (2) the 40-foot upper rich zone, 21.0 gallons per ton; and (3) the 21-foot zone in which the Laramie Energy Research Center is conducting in situ experiments, 22.4 gallons per ton. One acre of the 21-foot experimental section represents 34,300 barrels of oil in place, and 1 acre of the Tipton's 40-foot rich upper layer represents 62,000 barrels.

Jan 1, 1972

By J. P. Coughlin

Gypsum plaster is calcium sulfate hemihydrate (CaS04-1/2H2O). There are two varieties, commonly designated as a and ß. The hydration setting) of this plaster involves the chemical reaction: CaS04?1/2H20(c) + 3/2H20(l) = CaSO4?2H20(c); that is, the hemihydrate combines with water to form the dihydrate. Many substances, when present as impurities, either in the hemihydrate or the water have influenced the rate of the hydration reaction. The objective of the Bureau of Mines work described in this report was to investigate the accelerating or retarding effects of small amounts of dissolved substances and to attempt to classify these effects upon a chemical basis. To eliminate competing effects, the work was conducted separately on the two varieties of hemihydrate; both were in highly pure form. (Commercial plasters usually are a mixture of the hemihydrates, with other substances present as impurities.) As the hydration reaction of each variety of hemihydrate evolves heat in amounts known from previous work, 5,6/ the authors decided to use calorimetric methods to follow the extent of the hydration reaction as a function of time. Two calorimetric methods were employed. One was designed to study the hydration reaction with a large water to plaster ratio and the other with a small water to plaster ratio (to simulate commercial practice in utilizing plaster).

Jan 1, 1959

By Thomas J. Peters

This report is part of the U.S. Bureau of Mines Idaho Land Assesment Program to study the mineral resources of priority roadless areas in Idaho. The results of these mineral inventories provide minerals information needed to make wise decisions regarding future land management practices, and to ensure a dependable supply of minerals at a reasonable cost. The 16,300-acre Lionhead area, studied in 1991, lies along the Montana border north of Henrys lake, 10 mi west of West Yellowstone, Montana. The study area includes much of the rugged Henrys Lake Mountains, and is largely covered with conifer forest. Several peaks are over 10,000 ft in elevation. The Lionhead area has been proposed for Wilderness. No mineral resources were identified within or near the Lionhead study area. Five prospects occur in, or within 1 mi of the area: these include 1) an intermittently used road gravel pit, 2) the Thimbleberry lateritic iron prospect, of geologic and historic interest only, 3) the Tick Heaven talc prospect, 4) the Dry Fork garnet prospect, and 5) the lynx prospect, which appears to be of historic interest only. Talc is seen only as float at the Tick Heaven prospect, but the geology is permissive of talc resources at depth. The garnet prospect, and nearby similar alluvial terrane, mainly outside the study area, appears to be the most likely setting to contain mineable resources. Examined workings include four trenches and pits in rock and one gravel pit.

Jan 1, 1992

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

By H. C. Young

This paper deals with roof bolting in Alabama coal mines and iron-ore mines from the time it was introduced in early May 1948 to May 1, 1953, a 5-year period. The Tennessee Coal & Iron Division of the United States Steel Corp. began systematic roof bolting in early May 1948 in a coal mine and in an iron-ore mine, which had some of the poorest roof conditions in the Alabama mines. After the efficiency of roof bolting had been proved by the Tennessee Co. it was gradually adopted by other companies throughout the State, until in May 1953 approximately 53 percent of Alabama's total coal production and 100 percent of Alabama's total iron-ore production, mined underground, was being produced from roof-bolted areas. Statistics in this report will show the advancement made in roof bolting in the 5 years and also the amount of roof bolting that was being done as of May 1, 1953. Significant progress has been made in the coal and iron-ore mines of Alabama in reducing the roof-fall fatality rates during the past several years by adopting systematic roof bolting. The groundwork was laid through successful experiments early in 1948 by the Tennessee Coal & Iron Division of the United States Steel Corp. in cooperation with the Federal Bureau of Mines. This experimental work was based upon the previous experience of the St. Joseph Lead Co.2/ in its Southeastern Missouri mines.

Jan 1, 1954

By A. W. Fahrenwald

As an aid to studies of grinding, a batch laboratory classifier and elutriator has been developed at the U. S. Bureau of Mines Metallurgical Field Office at Moscow, Idaho, in cooperation with the University of Idaho. It is designed for use in conjunction with other batch laboratory apparatus, such as ball mills and flotation machines. It is shown in Figure 1. Description and Operation of Batch Laboratory Classifier The classifying column is a cylinder 4 feet 2 inches long, of 5 3/4-inch inside diameter, and terminates at its top in a cone or funnel 18 inches in diameter at the overflow elevation. The pressure chamber is of the same diameter as the classifying column, and has a conical bottom; it is provided with two openings, one in the cylindrical portion through which water is admitted, and the other, a small drain hole, in the apex of the conical bottom. The two compartments are bolted together and communicate with each other through the medium of a constriction plate provided with 3/16-inch holes spaced 1/2 inch apart. Constriction plates having any other percentage of opening may be substituted as the needs demand water is admitted to the compartment below the constriction plate at constant pressure. The volume of eater admitted is controlled with a valve. It should be mentioned that the classifying column at the bottom, just above the constriction plate, is glass.

Jan 1, 1929

By Charles S. Allbright

To develop a method for predicting the stability of a fuel during long-term storage from rapid aging tests at 200° F, the Bureau of Mines determined the stabilities of three gasoline base stocks and an alkylate blending stock in both sealed storage and aerated storage at 110° F for periods extending to 32 weeks. Stabilities of samples containing gasoline-additive compounds were compared by aging, using two methods--rapid aging in a bomb at 200° F for intervals up to 16 hours and storage at 110° F. The additives used were an uninhibited tetraethyllead motor mix, N,N'-di-sec-buty1-p-phenylenediamine and 2,6-di-tert-butyl-4-methylpheno1. Results were related by graphs that enable predictions of gum and sediment formation during storage from data obtained in bomb tests. A premium-gasoline base stock and the alkylate proved to be stable, but the two regular-grade gasoline base stocks were found to be unstable. Addition of the diamine antioxidant improved the stability of both of the regular gasoline base stocks, while the phenol antioxidant improved only one of them. The presence of the tetraethyllead decreased the storage stability of all four fuels, both with respect to formation of gum and precipitation of inorganic sediment. The rapid test at 200° F appears to offer promise as a basis for a method of predicting gasoline stability in long-term 110° F storage.

Jan 1, 1968

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

By A. R. T. Denues

"INTRODUCTION The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining.In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives. Cushioned blasting is designed to save the energy usually lost in excessive shattering and in this way to effect economies and to produce increased proportions of desirable lump coal. That this saving should lead to greater efficiency is indicated by an analogy with the theory and experience of size-redaction by crushing or grinding from which it is known that a large proportion of the energy consumed is expended in producing the smaller sizes (26),3/. Aside from these considerations, increasing the yield of lump coal is important in practice because larger sizes of coal usually sell at higher prices. Some statistics published in England in 1934 (63) illustrate the economic origin of the interest in increasing yields of lump coal; these indicate for three sizes of coal that as the size decreases the value decreases in the approximate series 3:1.5:1, thus:"

May 1, 1940

By H. G. Iverson

An investigation was conducted on the conditions affecting the precipitation of aluminum by autoclaving synthetic solutions containing Na2SO4, Al2(SO4)3, H2SO4, and H2O. Virtually all of the alumina could be precipitated as natroalunite (NaAl3(SO4)2 (OH)6). This product could be readily filtered and dried. Results are reported in terms of alumina precipitated in this compound and not in terms of alumina itself. Solutions of ~ 0.30, ~ 0.60, and ~ 0.80 mole/liter A1203 and various concentrations of H2SO4 and Na2S04 were investigated. The optimum time and temperature for autoclaving were 20 to 30 minutes at 200° C. The highest yields of natroalunite were obtained from solutions containing little H2SO4 and ~ 2 moles Na2SO4 per mole A1202. Acid in quantities of 0.3 to 0.5 mole/mole of alumina in solution depressed the yield to 90 percent or less. In differential thermal analysis, at 1,000° C the natroalunite precipitate decomposed without melting to yield SO, and SO2 gases, a solid composed of Na2SO4, and gamma and alpha Al203. Continued heating to 1,200° C produced No SO, and alpha A1303. Water-leaching of this product removed the Na2S04 and left a final residue of alpha A1203.

Jan 1, 1968

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

9. Remote Sealing System Sensitivity 9. 1 Introduction In the previous sections a description of the overall system has been presented along with detailed descriptions of the equipment and techniques employed with the preliminary probing system, the seal em¬placement system and the seal checking system. In addition, the use of these subsystems in a specific mine application has been described in considerable detail. A broad range of parameters of interest was specified in the contract, as summarized in Section 1. 3. Most of these are a function of the general location; i. e. , the location of the mine, and the specific location; i. e. , the location of the boreholes. These parameters of interest include passage size, shape, depth, slope and water con¬ditions. The length, diameter and location of the boreholes within the mine passage and on the surface are critical parameters as well. A few additional parameters may affect one or more of the remote sealing subsystems. These include temperature, topography, rock and soil conditions, and underground water. While variation in these parameters will not render the system inoperative, consideration of them in the planning stages will simplify and expedite the field operation. In the following sections the effect of the various parameters on the remote sealing operation will be discussed. For clarity, the several tasks, borehole drilling and casing, preliminary probing, fly ash delivery, foam topping and seal checking, will each be considered separately.

Jan 1, 1973

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX A - PNEUMATIC TRANSPORT OF FLY ASH 1. Introduction Two types of pneumatic transport of fly ash are critical to the success of (1) Transport of fly ash from the fly ash truck to the entrance to the borehole. Depending on the surface topography, this may be horizontal, decential and ascential. (2) Vertical downflow of fly ash through the borehole. All fly ash trucks have limited pressure with which they can pump the fly ash. Thus, the pressure drop in the fly ash hose will define the maximum length for pumping and consequently the maximum distance that the fly ash truck can be parked from the auxiliary blower. The same relationships describe the flow of the dilute fly ash-air mixture produced by mixing with the auxiliary air from the blower and thus define the selection of the pipe diameter. These are im¬portant considerations in the proper selection of the location of the passages to be sealed and the type of surface preparation required. The flow characteristics of fly ash down the borehole determine the selection of the minimum borehole diameter and the blower pressure. This appendix presents theoretical analyses of these flow regimes and summarizes the limited experimental data obtained during the field tests at Grant Town, described in Section 8.4. The analysis for the borehole flow is presented first as it is of greater interest to the program. This is followed by a discussion of the horizontal flow.

Jan 1, 1973

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

By Richard A. Thomas, Charles D. Litton, Kenneth E. Mura, Harry C. Verakis

Experiments were undertaken to evaluate the flammability of typical noise abatement materials used to line the cab interior of mobile mining equipment. The experiments were conducted using three different experimental configurations: 1. A ventilated tunnel test. 2. A full-size cab test where the interior surfaces were lined with the sample material and then ignited near the floor using a methane-air burner. 3. Standard ASTM E-162 tests using a radiant panel test apparatus. This paper describes the tests and presents the results obtained for 15 to 20 different materials of various chemical compositions and thickness. With one exception, materials that did not exhibit flame spread in the tunnel test also performed well in the full-scale cab test. All materials that had passed only a small-scale flammability test, such as SAE J369, failed dramatically in all three of the above test configurations. With one exception, all materials that performed well in the full-scale cab test had flame spread indices < 25, based upon the ASTM E-162 results. The lone exception had an ASTM E-162 flame spread index of 68. With regard to samples that failed the full-scale cab test, the carbon monoxide levels within the cab reached lethal concentrations in the range of 1.8% to 3.8% within 2 minutes from ignition of the sample—dramatically illustrating the severe fire environment that can result within the cab space.

To more rapidly and economically prepare solutions for chemical analysis, of a wide range of ores, slags, minerals, and metals. Approach A Simple pressure-dissolution system was devised using an inexpensive, heavy wall plastic bottle containing a sample in an acid medium. Using the technique, a complex silicate sample can be dissolved in less than 1 hour. How It Works A weighed portion of a sample, ground to minus 100-mesh, is placed into a polycarbonate or polysulfone plastic bottle. A mixture of hydrochloric acid, nitric acid, and hydrofluoric acid then is added. The bottle threads are wrapped with a layer of Teflon tape to prevent leakage, and the bottle cap is screwed on tightly. The sealed bottle is placed in a balling water bath. In the hot water, the plastic bottle acts as a pressure vessel to contain the pressure generated inside it. This technique should only be used by trained experienced people who are familiar with the hazards of hot acids under pressure. After being cooled in cold water, the resulting solution is brought to the final volume by adding 1.5 weight-percent boric acid solution to the bottle. The cap is replaced, and the bottle and solution is reheated. Precipitated fluorides, as well as any residue, are dissolved by the fluoride-boric acid reaction. The resulting clear solution then is suitable for spectro-photometric examination or other analysis.

Jan 1, 1980

By H. H. Schrenk

The safe use of a refrigerant or any substance depends on knowledge of its pertinent properties and conditions of use; therefore some of the properties of refrigerants that are related to life, fire, and explosion hazards are discussed herein. These data serve as a basis for suggested control measures in the use· of refrigerants. The properties of refrigerants may be broadly classified into three main groups: (1) Those important for refrigeration, (2) those significant from the standpoint of confining the refrigerant, and (3) those that become important if the refrigerant escapes from the :machine or container. The first group of properties, such as latent heat of vaporization, specific heat of vapor, specific heat of liquid, etc., is not considered to be directly related to safety and is not discussed here. The second group, those properties important in confining the refrigerants, has particular significance because· it relates to "built-in" safety. This group is emphasized because it is believed the soundest procedure in designing equipment is to give due consideration .to both the health and safety hazards likely to be associated with the equipment. Furthermore, the toxicity, fire, and explosion hazards are controlled as long as the refrigerant is confined. Some properties of this group are (1) stability, (2) corrosiveness, (3) boiling point, (4) pressure developed in the system, (5) warning odor or irritation, and (6) ease of detection. The third group includes such properties as toxicity (of compound and decomposition products), irritating action, and explosibility.

Feb 1, 1942

By H. R. Appell

The Bureau of Mines studied the conversion of a variety of cellulosic wastes, for example, sawdust, bovine manure, sewage sludge, urban refuse (free of metal and ceramics), etc., to heavy oils. The objective of the investigation was to determine the scope of the reaction and elucidate the chemistry involved. The reactions took place in the presence of synthesis gas and water or carbon monoxide and water under conditions of elevated temperatures and pressures. Waste conversions above 90 pct, often near 99 pct, with oil yields in the range of 40 to 60 pct, were obtained in the temperature range of 250° to 425° C and pressure range of 1,500 to 4,000 psig. Because mild conditions were sought, most of the experiments were conducted at temperatures of 250° to 350° C and pressures of 1,500 to 3,000 psig. In general, lower viscosity products were obtained at higher reaction temperatures. Conversions and oil yields were significantly increased by operating in the presence of a high-boiling oil; either anthracene oil or oil recycled from the process was satisfactory. Synthesis gas containing 50 pct carbon monoxide gave satisfactory results as a replacement for carbon monoxide. Cobalt molybdate on alumina catalyst, used with sodium carbonate, gave a product of lower viscosity and lower oxygen content than sodium carbonate used as the sole catalyst. The waste-to-oil process has been successfully investigated in continuous flow equipment as well as in batch autoclaves.

Jan 1, 1975

By Wilbur I. Duvall

Surface vibrations of ground, rock, and structures resulting from blasting or other sources are often measured with portable seismographs. These instruments are usually supported by a three-point mount or tripod which is simply placed on a horizontal surface on which vibration levels are to be measured. The rigid-body motion of a tripod-supported seismograph is considered from the point of view that there should be no slippage of the feet with respect to the surface and none of the feet should leave the surface as a result of imparted motion. From these studies the following design criteria are deduced which assure that the seismograph will respond accurately to vibration levels as large as 1/2 g.:3/ First, the coefficient of friction between the feet and the surface on which the instrument rests should be as large as possible, preferably approaching unity; second, the center of gravity of the instrument should be vertically above the centroid of the three-point mount; and third, the vertical distance between the center of gravity of the instrument and the centroid of the three points of contact with the surface should be less than the perpendicular distance between the centroid point and anyone of the three sides of the triangle formed by the three points of contact. Portable seismographs that do not satisfy these conditions should be clamped to the surface if vibration levels above 0.1 g. are to be recorded.

Jan 1, 1961

By R. V. Ramani, P. M. T. White, D. Sutton

1.1 General The examination and evaluation of a mineral deposit to determine whether or not it can be profitably exploited entails many factors unrelated to the physical nature and intrinsic worth of that deposit. Nevertheless, geology and geologically related factors have great bearing on the economic potential of the deposit. This is only natural because the deposit owes its existence to these factors. This is even more so in underground mines where the whole system is a geologically enclosed one. Geology plays a major role in at least four phases of a mineral venture. Firstly, it acts as an indicator of the existence of parti¬cular minerals. For example, it is inconceivable that a sedimentary coal deposit would exist in a granitic batholith or stock, or that a sandstone would host primary copper or nickel sulphides. Further, the positional relationship of different rock types may be significant in locating deposits such as replacement zinc and copper sulphides in limestones which have been intruded by igneous rocks. Thus, geology is important in the exploration phase of a mineral deposit. Secondly, once potentially valuable minerals have been discovered, knowledge of geology plays a significant role in determining the dis¬tribution, grade and extent of the mineralization. Controls on mineralization include one or all of those related to structure, rock type, sedimentary features, post-depositional redistribution, etc. Con¬sequently, in order to effectively evaluate a deposit in terms of

Jan 1, 1974