Search Documents

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and can be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated, but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project, to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fourth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 3, 4, and 5). Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. This part (part 4) and part 5 both deal with the closeout phase of the field demonstration. The quenching of the fire is described in this report, and part 5 will describe the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection with fume exhaustion is a potentially effective method for cooling large underground fire zones. Further trials of both Burnout Control and water injection with fume exhaustion are planned.

Jan 1, 1984

It was decided to demonstrate the use of latex as a soil sealant by irrigating three small plots at Lanse coded 03A on the west of Brown's run, 3C on the east of the stream, and SB, an area on the spoil bank. Earlier plans to sprinkle latex on twenty acres of the side were abandoned because of easement difficulties. On the basis of results from laboratory soil columns and small plot experiments at Lanse, Naugatex J-3471 was the latex of choice. The irrigation system consisted of plastic pipe (two inch size) for the main line from the water meter to the irrigation area because of lower price and ease of handling. Because the municipal water supply was limited to 20 gpm, low-volume 14V-LA-TNT Rainbow sprinklers were specified with low angle 20° 3/32 inch nozzles to reduce wind effects. At the expected nozzle pressure of 50 psig, each sprinkler covers a 56 foot diameter area at a delivery rate of 1.64 gpm. Each of the three test areas was covered with twelve sprinklers, six used with water alone as a control area and six used with latex and subsequent water spraying. One-quarterturn inlet valves were positioned on the main lines leading to each area. Flow to the treated and untreated areas was set at 10 gpm by Dole flow control valves in the' main entry lateral to each of the six sprinklers. To avoid the use of dilution tanks, a Moyno pump operated by a 1/2 HP, 1140 rpm 5:1 reducing drive was used to deliver 1/2 gpm 48% latex for mixing with 10 gpm water. A 3500 watt gasoline generator provided power for pump and light. Latex was applied at night to take advantage of the lower evaporation and higher humidity. Neutron gauge access tubes were placed in orthogonal arrangement in the areas that were irrigated, with four tubes in the section that were sprinkled with latex and four tubes in the untreated irrigation section in each of the three locations. Each tube, five and one-half feet long and sealed at one end with a plug welded in place, was inserted five feet into the ground in a cored hole. In each irrigation area, the left section of six sprinklers spread the dilute latex while the right section sprinkled the same amount of water to serve as a control plot. As shown in Figure 7 each sprinkler has a 56-foot sprinkling diameter at 50 psig design water pressure. The sprinklers are 30 feet apart on the laterals and 35 feet apart between the laterals. The access tubes (coded AT on Figure 7) were placed in comparable spots on the two sections of each area, so that four soil moisture measurements on the two sections could be compared. Bouyoucos resistance blocks (BB) were also placed in areas 03A and 3C at one, two and three foot depths, but not on the spoil bank area.

Jan 1, 1972

1. COAL PRODUCTION: Under Section 402 of Public Law 95-87 (SMCRA), coal operators are required to pay a fee when coal is sold, used, or transferred. These fees are deposited in the U.S. treasury as the Abandoned Mine Land Fund. Information about the type of coal (bituminous, lignite, or underground) and tonnage are tabulated on Form OSM-1 and submitted with the fee, which is paid quarterly to the Office of Surface Mining. The coal production data presented in this report was compiled from information stored in the Office of Surface Mining Fee Collection System computer data base. Collection of the fee began with the last quarter of 1977; therefore, 1978 data includes the last quarter of 1977 and the first three quarters of 1978. Information for each successive year follows the same tabulation pattern. Surface production includes both bituminous and lignite coal; underground includes tonnage reported as underground mined. In New Mexico and Montana, coal production on Indian land is listed under the Crow, Hopi, and Navajo Tribes. 2. HISTORIC COAL PRODUCTION: Federal Government agencies have published coal production data since 1807, the date of the earliest record. The source of coal production data used to compile this graph was: 1891-1895, U.S. Geological Survey, Division of Mineral Resources; 1896-1977, U.S. Bureau of Mines annual Minerals Yearbook; 1978- 1991, Office of Surface Mining data described in footnote 1 above. 3. NUMBER OF MINES: The number of mines was compiled from Office of Surface Mining Fee Collection System data described in footnote 1 above. Annual totals were calculated by adding together the number of operations with the same Mine Safety and Health Administration numbers reported each quarter and dividing by four to give an annual number in each state. 4. ENFORCEMENT ACTIONS: Enforcement action data was compiled from annual reports developed by Office of Surface Mining field offices and historical field office records. The data presented are all actions taken by both the state regulatory authority and the Office of Surface Mining. Citations issued are the sum of Notice of Violations (NOVs) and Cessation Orders (COs). Because the Hopi and Navajo jurisdictions overlap in Arizona and New Mexico, enforcement actions data for the tribes have been combined in annual reports prepared by the Albuquerque Field Office; therefore, they are combined for this report and listed under Navajo Tribe. 5. ACREAGE PERMITTED: Acreage permitted data was compiled from annual reports developed by Office of Surface Mining field offices and historical field office records. The acreage listed was permitted during the year shown and is not the total acreage under permit during that year. 6. BONDS RELEASED: Acreage of reclamation bonds released was compiled from annual reports developed by Office of Surface Mining field offices and historical field office records. The sum of final Interim Regulatory Program bonds and Phase 111 (or final release) bonds shows only the land area where reclamation is complete and has been released by the regulatory authority.

Jan 1, 1992

By Jr. Holmes

"The Riley tungsten property of the Northern Nevada Mining Co. was examined by the Bureau of Mines in August 1943, and from February 22 to August 22, 1945, the property was explored by the Bureau.Riley mine, which comprises 60 acres, is in sec. 9, T. 38 N., R. 42 E., Mount Diablo base and meridian, in the Potosi Mining District, on the east slope of the Osgood Range in eastern Humboldt County, Nevada. J. S. Riley is president of Northern Nevada Mining Co., the general offices of which are at 29 East First Street, Reno, Nev.Winnemucca, Nev., 42 miles southwest of the mine and on the main line of the Southern Pacific and Western Pacific Railroads and U. S. Highway 40, is the nearest supply center. The post office for the Potosi district is 15 miles south at Red House, Nev., a station on the Southern Pacific and Western Pacific Railroads. A good dirt road, which leaves U. S Highway 40 about 15 miles east of Winnemucca, extends northeast to the property.Tungsten occurs as scheelite in a characteristic Nevada contact-metamorphic tactite deposit between limestone and granodiorite Fifteen diamond-drill holes were completed for a total length of 2,630 feet.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Special acknowledgment is made to A. C. Johnson, chief, :Reno Division, Mining Branch; E. O. Binyon, mining engineer, Reno Division; S. F. Clabaugh and S. Warren Hobbs of the Federal Geological Survey, who made available the un¬published Geological Survey report ""Tungsten Deposits of Osgood Range, Humboldt County, Nevada;"" and S. P. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch, Salt Lake City, Utah.The Riley tungsten property comprises 60 acres of patented land owned by the Northern Nevada Mining Co. of Reno,,a partnership comprising J. E. Riley, H. H. Luce, Phyllis Riley, Beatrice Knight, Gene Crosby, and M. R. Wilson.The property is part of a federal land grant to the Southern Pacific Railroad, from which it was acquired by Tom Dernan many years ago. Two short adits and several shallow pits were excavated in a search for silver ore, but no record of precious metal production exists."

Sep 1, 1946

By L. C. IlsLey

The Burrell methane indicator developed by Col. G. A. Burrell in 1915 was modified during 1918 to the " insulated type " Burrell indicator . Though this instrument has been used in mines since its first introduction , it was not formally approved as safe and efficient for use in gaseous mines until March , 1922. The indicator is built by the Mine Safety Appliances Co. , Pittsburgh , Pa . Approval No. 800 has been assigned to this company covering the device in the form approved . The principle of the Burrell indicator is fairly well known . It works on the same principle as the Haldane apparatus - measuring by means of a graduated scale , the contraction resulting from burning the methane content of an air and gas sample . A given aniount of the mine atmosphere to be tested for methane is taken into the indicator . This sample is then thoroughly shaken with the water in the indicator for one minute . The methane in the sample is now burned for two minutes by a heated platinum coil , which is energized by a small storage battery containing two Edison cells connected in series . After the glower or coil has burned for two minutes , it is disconnected from the battery , and the indicator is again shaken for The amount of contraction observed by reading the height the water rises in the U- tube of the indicator , which is calibrated to register the percentage of gas in the sample . The indicator as approved by the Bureau of Mines is equipped with an Edison M- 8 mine- lamp battery , and with a glass and scale graduated from zerɔ tɔ four per cent methane . The approval of a corbination service that is , an attachment for giving illumination from the same battery from which the platinum glower is operated has been withheld pending the development of a battery with larger capacity . - Under laboratory operating conditions , a single glower was capable of making at least 20 determinations if proper precautions were observed with respect to the use of freshly charged batteries . A battery should be allowed to stand off charge several hours before using in an indicator , as the peak voltage of a freshly charged Edison cell is abnormally high and is likely to send enough current through the glower to melt the platinum wire . Fifty-seven satisfactory operations were obtained from a completely charged battery . The point where the voltage of the cell fell below 2.3 volts with the glower attached was taken as the lower limit of successful operation . A voltage less than 2.3 does not permit the lower to burn at a temperature that will completely burn the gas in the air , thus giving a false indication .

Jun 1, 1922

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By J. D. Ramsdell

To obtain information on the effects of cobalt on microstructure and tensile properties of titanium-vanadium-cobalt alloys, the composition ranges of 4 to 16 percent vanadium with 1 to 4 percent cobalt have been studied. The beta phase was not completely retained with vanadium additions up to 16 weight-percent or in the same alloys containing up to 4 percent cobalt.

Jan 1, 1960

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By S. A. Allen

The Eufaula bauxite district of Barbour and Henry Counties in southeast Alabama covers an area approximately 14 miles long, 6 miles wide at the eastern extremity near the Chattahoochee River, and 10 miles wide at the western end near the east fork of the Choctawhatchee River (see figs. 1 and 2). The long axis of this polygon bears a little south of east.

Jan 1, 1949

By Charles W. Briggs

The steel foundries of Germany were investigated for the purpose of ascertaining (1) the type and classification of steel structures produced as castings, (2) processing methods, (3) the mechanical properties of carbon and alloy cast steels, (4) the type and character of defective castings, (5) the appearance of castings, (6) research in steel castings, and (7) plant lay-out and equipment.

Jan 1, 1946

By Llewellyn A. Rubin

ROUTINES AND SUBROUTINES A- 1 Wait Loop (Wait) A- 2 Receiver Processing (RCVP) A- 3 Control Panel Sequence (CPNL) A-4 Interrupt Routine (INTRP) A- 5 Math Processing Routine (PROC) A-6 Input Constants for Math Routine (CONI) A-7 Angle Conversion Routines (LVERT) A- 8 Display Routine (DSPY) A- 9 Message Print Auxillary Routine (MESSO) A-10 Auxillary Subroutines (AFUTC and AGETC)

Jan 1, 1973

By R. Craig Smith

This report presents the software documentation for PREY AL, a prefeasibility mineral property evaluation program developed by the U.S. Bureau of Mines on a Lotus 1-2-3 spreadsheet. It is presented in a step-by-step "user?s manual" format. Appendixes contain the technical assumptions, program default values, and a summary printout detailing capital and operating costs and cash-flow analysis.

Jan 1, 1992

By Alexander May

In this Bureau of Mines publication stability constants for complexes of diethylenetriamine, 2-aminoethyl sulfide, triethylenetetramine, and 1,8-diamino-3,6-dithiaoctane with copper, nickel, zinc, and cadmium were deter-mined. The amine complexes were found to be much more stable than the analogous thio complexes. The results are interpreted in terms of possible molecular structure of the complexes.

Jan 1, 1974

By Andrew B. Cecala, Robert J. Timko, Alexander D. Prokop

Bag loading and stacking processes are the highest dust-exposure job categories in the metal/nonmetal mining industry.1 To cost-effectively decrease respirable dust levels, the Pittsburgh Research Center of the National Institute of Occupational Safety and Health (NIOSH), formerly of the U. S. Bureau of Mines, designed and tested a system called the Bag and Belt Cleaner Device (B&BCD). [ ]

Introduction MINING IS THE BRANCH OF INDUSTRY involving the exploration and removal of minerals from the earth (figure 1). Mining is one of the oldest and most important endeavors of humankind, because it provides the raw ingredients for most of the material world around us and, like agriculture, is the lifeblood of civilization. The main objective of any type of mining is to remove the valuable material economically and safely with minimum damage to the surrounding environment. The Earth has many natural resources on which we depend that must be mined. Coal, oil, gas, and other mineral fuels are used for heating electricity, and numerous industrial processes. Nonfuel minerals such as iron ore, precious metals, and industrial metals, and nonmetallic materials like sodium and potassium are used in chemical and agricultural applications. Even crushed stone used in road building and other construction projects must be mined. Mining affects our standard of living and impacts almost everything we do. A myriad of items that we use in our homes and offices and for transportation, communications, and national defense all require minerals (figure 2). For example, more than 30 different minerals are needed to make a television or telephone! Table 1 lists several commonly mined materials and some of the end uses in our daily lives.

Jan 1, 1995

By Robert F. Chaiken

Burnout Control is a process developed by the U.S. Bureau of Mines for accelerating the burning of wasted coal fires in situ, while at the same time controlling the heat and fumes produced. The Albright fIre project is a fIrst fIeld trial of Burnout Control as applied to a coal waste bank. An exhaust ventilation system was designed and constructed and then operated over a 1-year period at the site of an existing abandoned mine land fire near the town of Albright, WV. While predicted exhaust gas temperatures of 900° C and thermal power levels of 5 MW were achieved at 20-to 3O-in H20 vacuum levels, problems were encountered with engineering designs, equipment breakdown, and fuel-rich combustion that curtailed the time period of satisfactory operation. Effective afterburning of the exhaust gases (as they were drawn from the bank) corrected the problems associated with combustion stoichiometry and led to high thermal outputs. It is believed that with (1) improvements in engineering design and construction, (2) better control of the afterburning process, and (3) the use of conventional stack gas air-pollution controls, Burnout Control can be applied successfully to a coal waste bank fire.

Jan 1, 1991

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974

By John J. Baz-Dresch, Kenneth L. Bickel, Winthrop F. Watts

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel- powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the mine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 1994