Search Documents

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

By Uli Leiste

Two papers are presented which examine Air Deck Blasting, one from a computational aspect and the other from a shock aspect.

Jan 1, 2016

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By Ken Eltschlager, J Silva Castro, J. M. Hoffman, Braden Lusk

This case study focuses on analysis of sounds inside a house induced by blasts as result of surface mining coal in West Virginia and how to better communicate technical information to the public. The field study included a house wide vibration and sound monitoring system installed in a home which was subjected to blasts at varied distances and direction. The structure response was separated into ground vibration and airblast induced movement due to the differences in their times of arrival. This signal was then compared to the sounds recorded to determine which component of blast (ground vibration or airblast) induced the maximum sound. Findings shows that blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond this distance the maximum sound response was caused by ground vibration without exception. The kitchen generally created the most sound. The second phase of the study was to gauge the public’s response or preference to technical information. Three hundred and forty eight (348) telephone surveys were conducted in Logan and Boone counties West Virginia. Based on the survey, the public prefers units of pounds per square inch (psi) for airblast and millimeters of displacement for ground vibration. Ultimately a public relations plan was developed based on the results.

Jan 1, 2012

By Charles Zdazinsky

Many blasting applications in the mining industry demand that the hard rock being blasted remains structurally competent. For example, pre-splitting is a common technique to reduce fracturing, and operators of dimension stone quarries use this blasting method to eliminate overbreak. When pre-split design parameters are not applied correctly, there will be a redistribution of stresses within the rock, resulting in Blast Induced Rock Damage (BID). Advances in geophysical technology are enabling blast technicians to monitor BID and then use the results to correctly design their blasts.

Jan 1, 2011

By Florian Bauer

The Fording River mine in British Columbia produces hard coking coal in an open pit operation. Coal seams are exposed by blasting overburden and digging blasted muck with rope shovels. The drilling and blasting process presents a considerable cost factor to the operation. Reducing the amount of explosives needed therefore contributes considerably to costs saving initiatives. However, reducing the powder factor only makes sense if the subsequent loading processes by the shovels are not compromised in terms of productivity.

Jan 1, 2014

By Dieter Froelich, Giles Turcotte

In the near future, Bong Mining Company (BMC) will start mining a new deposit known as Zaweah II which is a narrow iron orebody requiring multiple row blasts with the bench floor as a free face. This called for the development of a new blasting technique. The article delineates the problem and its restrictions related to blasting. It also describes the approach which was taken for developing this new blasting technique which is essentially an application of the cratering theory with near spherical charges. Basic crater tests were conducted using various combinations of hole sizes, explosive strengths and delay patterns. From the results obtained, several alternatives were considered for production blasts and the most promising ones were evaluated.

Jan 1, 1980

By J R. Hearst, T R. Butkovich

Explosive-induced fracturing and permeability enhancement far from a free face were studied. A one-dimensional computer program, SOC, was used to predict the total failure-associated distortional strain, ef. Laboratory and field experiments associated the calculated ef with the observed fracture and permeability enhancement. An ef value of 0.015 corresponded to the observed radius of effect, which was about seven times the cavity radius and was consistent with predictions from SOC and from the literature.

Jan 1, 1976

By Jason M. Ryan, T Michael LeBlanc, John H. Heilig

"Drill trajectory deviation is a recurring problem in vertical retreat stoping operations. As a result of thisdeviation, 60 kilogram (165 millimetre diameter) and 103 kilogram (203 millimetre diameter) explosive charges are routinely detonated beyond ore/waste contact zones. Consequently, there follows a reduction in finished stope wall stability and an increase in ore dilution."

Jan 1, 1996

By Chick Kerkering, Stephen Iverson

Perimeter control blasting is common in civil construction projects but not as common in mining. A poorly designed and executed underground mine development blast design can result in unwanted wall rock damage. This damage increases the risk of rock falls and injury. With the availability of good drilling equipment, it is a simple matter to add the few extra holes needed to change conventional drifting into drifting with perimeter control.

Jan 1, 2008

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Stewart A. Silling, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

GEM (Geologic Element Motion) is a Distinct Element Method (DEM) for modeling blast-induced heave. It was developed with a very fast computational algorithm that efficiently treats many different element shapes utilizing alternating arcs and lines to create GEM elements. The GEM computational technique has been previously documented so only a summary will be included in this paper. New features of GEM are the ability to define the size of the rounded corner radius as well the length of the sides for quadrilateral and hexahedral elements. Circles can be created from a quadrilateral element with zero length sides and four arcs. An additional new GEM feature is energy partitioning between brisance and heave. This physics-based partitioning is essential for accurate modeling of blast results over a wide range of rock and explosive types. It accurately defines the volumetric, pressure and energy state of the explosive gases in a blasthole following detonation. Rock mechanical properties and explosive characteristics are included in the calculations. Example simulations provide comparison of the GEM predicted heave for two different classes of explosive. A GEM simulation utilizing hexahedral elements is compared with previous modeling incorporating circular elements.

Feb 6, 2023

By Javier Castaneda, Luis Zozaya, Noel Huarachi, María Rocha

The objective of the project was to implement and calibrate drill and blast models supported by Geotechnical and Geological models as well as the mine and operation characteristics. The models would then be migrated to HxGN Blast to ensure a productive process that is simplified, digitized and optimized.

Feb 1, 2020

By R. F. Favreau, Patrice Favreau

"Ever since we have started to assist those responsible for blasting with blast simulation studies, we havebecome aware of an interesting aspect, namely that in 90 % of cases we are asked ‘‘Can you seek ablasting method which gives better fragmentation than the method which we use now’’. But after a visit to the site, and the evaluation of the fragmentation obtained with their present blasting method, it very often becomes evident that it is the ease of mucking and not the fragmentation which requires improvement. Hence we then proceed to do a simulation study the results of which are improved mucking rather then more fragmentation, and those responsible for the blasting always become very satisfied."

Jan 1, 2017

By John Brennan

The Avalauncher has been an integral tool for avalanche mitigation work for close to 50 years. With their ability to place a kilogram of high explosives up to two thousand meters away, they routinely serve as a short range alternative to military artillery. The Avalauncher’s roots can be traced to a pneumatic baseball pitching machine used by Major League Baseball teams in the United States in the late 1950s. Throughout the decades, many modifications have been made to both the launcher and its projectiles. Current technology has allowed the Avalauncher to attain greater accuracies and operational range. In this paper I plan to cover not only the history of the Avalauncher but also explore its potential future.

Jan 1, 2009

By Claude Cunningham

Late in 1982 a fire began in the shallow, abandoned workings of the Uitkyk Colliery near Witbank, South Africa. Urgent measures had to be taken to quench the fire, before the surface caving it caused could put an important railroad connection out of action. This paper outlines the way in which the job was tackled.

Jan 1, 1984

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By Sandor Nagy

The Explosive and Blasting Department of the Hungarian Mining Research Institute is responsible for the research and development of industrial applications of explosives. Appropriate explosives technology is developed for each application, including the explosive demolition of structures, which belongs within our charge.

Jan 1, 1977

By N L. Thomas

Hole size affects many factors which directly influence fragmentation in the muckpile and hence, the cost effectiveness of the entire operation. These factors include production capability, explosives and accessories efficiency and usage and drilling accuracy. In addition, hole size should be chosen to suit the geological conditions. The paper concludes that the optimum hole size is generally the largest that can be used commensurate with production and environmental considerations.

Jan 1, 1986