Search Documents

By AN Gupta, N V. Srinivasa Rao

Initiating devices like detonators use sensitive primary explosives. Successful detonation of secondary explosive is achieved by suitable source of energy from primaries. The most widely used primaries contain toxic lead azide and lead styphnate, dinitrodiphenol or tetracine. All these primaries are very sensitive to friction, impact and heat. The handling of these chemicals is very hazardous and many accidents reported in detonator manufacturing were from these primaries only. In addition to this high sensitivity, lead azide and lead styphnate contain lead which is toxic.

Jan 1, 2014

By Norman S. Smith, Troy D. Harris, Richard L. Ash

In open-cut bench blasting drilling boreholes below grade level is normally considered essential to insure toes do not remain. The extra drilling and use of explosive below floor level are not only expensive but on occasion cause serious problems including severe floor damage and excessive ground vibrations. It has been reported that under certain circumstances explosive in the subdrilling has been successfully substituted by broken rock with its associated benefits.

Jan 1, 1978

By Edward Jr Walter

This paper discusses the problems that arise in the process of developing adequate explosives noise legislation. Case histories are used to illustrate how and where these problems arise and the course of action followed in overcoming them. It is imperative that those concerned keep informed as to possible legislation and be prepared to present solid facts that will insure fair and reasonable controls.

Jan 1, 1975

Lightning Strikes on Vehicles Transporting Explosives The police in one of the countries in which we operate has asked about the consequences of a lightning strike on a vehicle (box van) carrying detonators and explosives. We have assured them that there is not a problem but they require proof of this.

Jan 1, 2011

By Rob Farnfield

The control of vibration from surface mine blasting by the application of detonator (cap) delay techniques has been universally accepted for many years. For almost as long it has been known that, for delay techniques to be effective, a minimum of 8 milliseconds delay must exist between blast holes.

Jan 1, 1999

By J P. Tidman

The problem of blasting fragmentation has received a good deal of attention in recent years. Progress by the scientific method requires a good set of experimental data as a benchmark to test models. Recent models have become so complex that it is not possible to use the results of field data because the complete set of parameters needed to describe the rock and/or explosive are not available.

Jan 1, 1991

By Shad M. Sargand, Manseok Chang, Glenn A. Hazen

Customarily, peak particle velocity of surface wave vibrations has been the recommended criterion for the prediction of blast damage to structures. Currently blast spectrum and natural frequencies of a structure have been also recognized as important for predicting damage potential. While others have considered the importance of structural frequencies, they have not analyzed the structural response spectrum when establishing damage criteria.

Jan 1, 1992

By Richard B. O'Meara

"The demand by a customer to an Explosives supplier to fulfill a specialised productrequirement was met by a level headed decision to try to satisfy that demand. This paperwill describe the fundamental steps required in order to develop and produce a newexplosives device, while under certain resource constraints, such that the needs of thecustomer and the supplier are met safely and effectively."

Jan 1, 1993

By Gregory L. Hempen

"Pressure waves from submerged blasting can have adverse impacts on nearby structuresand on aquatic fauna. Underwater blasting is not allowed for some situations withoutmitigation of these adverse pressures. Two states currently require bubble-curtain, pressurereduction of underwater shooting for environmental concerns. St. Louis District hasconducted field monitoring of scaled testing and demolition shooting with air-screenmitigation. The deployment of compressed-air manifolds and air-entrained packagesheeting effectively reduces underwater blast pressure. St. Louis District is preparing areport on optimum use of underwater-blasting mitigation measures."

Jan 1, 1993

By Jack Elorenta

A recent forum of mine operators revealed a continuing strong interest in alternative methods of freeing rock. A Rand Corporation report lists a continuous mechanical machine that would replace drilling and blasting as a priority for mine operators. Meanwhile, mounting evidence documents a dramatic cost benefit in processing where increased blast energy is available. The reasons for this dichotomy may be due to a number of factors.

Jan 1, 2002

By E Emery Jr Gray

The City of Richmond, in an effort to improve sewage treatment facilities, designed an invert syphon to cross the James River at Fulton Bottom. The design criteria called for installation of two 36-inch pipe' lines at an elevation of -35 with the mean water level being at elevation 00. This paper discusses the actual method of construction used to blast the river bottom. Choice of excavation equipment, nature of the river, as well as the geological structure, were taken into consideration.

Jan 1, 1979

By Unknown

Contact Local Law Enforcement Authorities. Contacting the local law enforcement authorities is essential to the quick recovery of explosives taken in a crime. Contact Local ATF Office. The local ATF office will work with the local law enforcement authorities investigating the theft. They can also assist in the preparation of the Theft/Loss Report for submission to the U.S. Bomb Data Center.

Jan 1, 2009

By Mauro Fornaro, Marilena Cardu, Renato Mancini, Daniele Castano

Tunneling by explosive blasting in civil works isn't merely intended to break somehow a way through the rock, rather to drive a permanent, constant cross section, lined way. The current mechanical excavation v/explosive blasting debate is mainly centered on the concept of the tunnel wall quality; and consequently explosive blasting strategy is founded on contour blasting.

Jan 1, 1992

By Mauro Fornaro, Marilena Cardu, Renato Mancini

Detonating cord cutting is widespread in dimension stone extraction, especially in the case of hard, abrasive stones as granites, an important resource for Italian industry. General data on this production sector are briefly discussed and analyzed in the first part of the paper. The theoretical basis of operation are summarized, and compared to data obtained from selected commercial cases, in the second part.

Jan 1, 1994

By Jim Breedlove, Stephen P. Case

When a major ground subsidence occurred in the AKZO Salt mine at Retsof New York, the company was forced to pick up their production from a lower mine level. Before full production on the lower level was possible, an escapeway and ventilation shaft would have to be constructed. Construction of a shaft under emergency conditions required some special techniques. Dynatec Mine Construction, Inc. of Lakewood Colorado was awarded a contract for the project.

Jan 1, 1995

By Harry L. Siebert, Thomas Gelormino

Rock excavation in urban areas occurs with maximum public exposure and, with the aid of explosives, is one of the challenges facing this industry today. Such excavation is also a hidden factor in areas of new growth, revitalization or upgrading existing facilities in or near urban areas.

Jan 1, 1985

By Fumihiko Sumiya, Koichi Kurokawa, Yukio Kato, Tetsuya Sawada

In some metal mines, it is a serious problem the decomposition of explosives which occurs suddenly by contact with ore containing pyrites under high temperature conditions. In the present paper, we investigated heat resistant properties of emulsion explosives and other industrial explosives by contact with ore containing pyrites under high temperature conditions.

Jan 1, 1992

By Zhang Shixun, Wang Xuguang, Zhong Yinting

The Mongol-Russian Joint Mining and Processing Cu-Mo Corporation Erdenet signed a contract with BGRIMM for building a plant to produce 10,000 t/y multitype emulsion explosives by using BGRIMM emulsion explosives manufacturing technology. In order to ensure the realization this contract, we have done a series of studies on the design of technological process and the selection, layout of the production equipment, and made a success.

Jan 1, 1997

By A T. Spathis, J J. Felice, T A. Beattie

High speed cinematography of surface blasting operations is used for diagnosing various aspects of blast performance. Several quantitative features may be derived including confirmation of the hole initiation sequence, time to first movement, evidence of stemming ejection and measurements of face velocity. Face velocity measurements using high speed cinematography have the following disadvantages: firstly, for accurate measurements placement of targets on the face and surveying of them is necessary; secondly, the analysis requires experience and time and can only be done after the film has been developed.

Jan 1, 1991

By A T. Spathis, J J. Felice, W Klass

Cast blasting has become one of the most efficient ways to move waste rock in open cut coal mining. It is used at Mount Thorley Mine in conjunction with a dragline to move some of the overburden onto the spoil dump.

Jan 1, 1992