Search Documents

By F. Q. Cheng

As the important potash, the product yield of KCl in winter is low and the resources waste is serious according to the deficiency of collectors, which can be used in this condition currently. This paper studied on the change of contact angle, turbidity, and flotation recovery of KCl particles when different chain lengths, ratios of amines were used as collectors in KCl flotation process to get a new mixed collector. The contact angle values of KCl crystal in its brine solution added different amine collectors were first measured by captive bubble method. The turbidity of brine solutions were then measured by the laboratory turbidimeter at room temperature when different amine collectors were contained. In the end micro-flotation experiment using mixed amine with fixed ratios and ODA as collectors respectively at 5 °C, 23 °C were performed. The results show when the ratio of the mixed amine is DDA- 20%, ODA-60%, C20-20%, the contact angle at KCl surface is the maximum and the hydrophobic state is best. Meanwhile the result of turbidity measurement indicates that the dispersion of mixed amine colloids is better than the ODA collector due to the addition of DDA, which plays the role of frother. The flotation results also prove that the mixed amine is not only fit for the KCl flotation at room temperature but also fit for its flotation at low temperature. This study provides strong technical support to extend the production time of potash business in Chaerhan areas in China.

Sep 1, 2012

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By D. G. Hulbert

"Mineral processes are complex operations that have been modelled, controlled and simulated by diverse technologies. A review is given of some models of mineral processes in the literature. A new variation of a dynamic process model of flotation is presented. Process models, describing real and relevant physical variables, give a good understanding and good qualitative simulations, but can sometimes require prohibitively difficult and extensive parameter estimations. Process control is usually best done on operational plants by the fitting of system models, which can home in on the plant?s observability, controllability and optimisation. System models can be of a form amenable for use in appropriate techniques for controller design and implementation. The control of milling circuits is discussed in some detail. While simulators use models to predict dynamic or steady-state information, part of their strength lies in their ease of use and their ability to test different types of specifications. Some results are given for a flotation circuit simulator that can be made to solve virtually any permutation of specifications.INTRODUCTIONThe development and application of appropriate technology can lead to better operation of mineral processing plants in industry, so that substantial benefits can be obtained from improved throughputs, efficiencies and product qualities. This paper addresses some of the principles and methods used in the quest for the development and exploitation of such technology. Although the design of processes is often the motivation for modelling and simulation, this paper also targets the use of modelling and simulation for the control and optimum operation of mineral processes. The two processes given the most attention here are flotation and milling.Technologies used in mineral processing range from simple to very complex. Simple technical principles, such as mass and component balances, can yield some simple and effective strategies for modelling and control. However, minerals in particulate form have such complex physical and chemical properties that there appears no end to the complexity that emerges, as more and more factors are taken into consideration in the pursuit of better results and understanding. The situation is aggravated by the complexity of mineral processing plants, which have spatially variable conditions within process units, and complicated interactions between these units."

Jan 1, 2003

By M. R. Robben

Carbonates have gained significant economic importance for the human kind. On one hand over a hundred uses are listed for carbonates. On the other hand, carbonates host base metal deposits. Although the carbonates play a significant part in the development of those deposits, in the mineral processing they consume acid and cause selectivity problems during flotation and leaching. Carbonates also accompany other industrial minerals as waste rock. For all those cases it necessary to find a technique to separate carbonate as early as possible in the processing chain. In this paper, the applicability of near-infrared spectroscopy (NIRS) sorting for the separation of carbonates is discussed. NIRS sorting is a sensor-based sorting technique, in which particles are singularly detected by a sensor and then rejected by an amplified mechanical, hydraulic or pneumatic process. This technique can for example be implemented in the process as a pre-concentration step for coarse particle sizes up to 300 mm. NIRS sorting discriminates among materials based on the difference that exist between their spectral properties in the near-infrared (NIR). Vibrations of molecular bonds in carbonates cause characteristic spectral properties in the NIR, which makes carbonates detectable, possible to identify, distinguish and separate from other rock materials. The spectral properties can also be used to distinguish between different carbonate minerals and mixtures. If the spectral variations are large enough for detection, sorting based on NIRS is possible. Feasibility studies on sensor-based separation of carbonates in the processing of talc, borate, fluorite, marble, zinc-oxides, copper sulphide and iron ore as well as the discrimination of calcite and dolomite mixtures are conducted and indicate the high potential of NIRS sorting in the minerals industry. Keywords: carbonate separation, sensor-based sorting, near infrared spectroscopy, NIRS sorting

Sep 1, 2012

By Victor Avdokhin, Ivan Kovlekov

"Studies of the process of concentration of gold-containing sands and technogenic resources show that the main reason of gold losses is misbalance between size of gold particles and degree of roughness of mineral bed. This results in free circulation of small gold particles in pores with following washing off the particles from the bed by turbulent flows.We elaborated design of magnetic sluice, intended for improving efficiency of recovering fine gold by optimizing magnetic field of a magnetic system on the base of forming catching coat from magnetic mineralsThe magnetic sluice includes trough-shaped body from magnetic-conducting material. On the bottom of the trough, magnets are placed, and opposite poles of the magnets are oriented outwards. Thickness of the bottom is determined to be sufficient for locking magnetic lines of force of the magnets on each other. The magnets of rectangular plate shape are placed on the rough bottom, covering the whole surface or with spare areas; the magnets are placed across the trough with alteration of rows with the same pole orientation.Catching coat is formed of natural magnetic and weak-magnetic placer minerals in field of magnetic system of the sluice. Magnetic minerals, placing along magnetic lines of force, form rough coat of fluffy structure. Size of the magnetic particles is chosen taking into account expected size of gold particles, which are to be fixed on the rough coat or between the magnetic particles. Changing coarseness of particles of mineral bed allows to regulate selectivity of recovering heavy minerals.Forming artificial fleece from magnetic minerals of initial sand, increasing capacity of the bed and relative hydraulic proportionality of mineral particles of the bed provide for the most effective recovery of fine gold."

Jan 1, 2003

By Robinson Irarrazabal, Edison Collinao, Rodrigo de Carvalho, Patricio Davila, Marcelo Tavares

"In recent years, DEM (discrete element method) softwares, along with 3D laser measuring equipment, have become powerful tools to describe mill charge behavior, as well as forces acting on the liners of SAG mills. With the aim of contributing to streamline this application of the advanced technologies ME Elecmetal and Universidade Federal do Rio de Janeiro, UFRJ, proposed a new approach to improve the design of mill liners using elements from mechanistic modeling of grinding. The paper presents a methodology for continuous improvement of liner design, which uses information from the DEM collision energy spectra in the mill discriminated for the different components (ore and steel balls), as well as information on the breakage properties of the ore being ground. From these it proposes the concept of "effective collisions", which corresponds to the collisions that are of sufficient magnitude to cause breakage, thus allowing to discriminate from impacts that do not cause breakage either in a first impact or after repeated loading. It also tracks the collision of steel balls against the shell in order to assess their potential damage to the liners. An industrial case study is presented of a 38’ diameter SAG mill, which was experiencing challenges associated to liner breakage and low efficiency with the old liner design. Through a modification of the liner design, simulations demonstrated the potential benefit associated to reduction in ultraprojection and improvement in mill capacity. Implementation of the new design in the SAG mill was carried out, resulting in increase in daily throughput from 6 to 12%. Further, the time spent in liner change was reduced by 47% given the reduction in the numbers of parts. This operation also benefited from having no stops due to unplanned shutdowns to replace broken tiles. These demonstrate the benefit of coupling advanced computational tools to sound engineering principles in continuous improvement of liners."

Jan 1, 2014

By N. N. Orekhova, I. V. Shadrunova, N. G. Novikova, N. ?. Volkova

The purpose of the research is scientific substantiation and formulation of strategy and technical solutions of handling liquid wastes of plants producing and refining copper-zink pyritic ores. In the course of research studied are chemical composition of technogenic waters of mining plants as well as water and alluvia of intake river within and outside a sanitary zone of Southern Ural mining plant using inductively coupled plasma mass-spectrometry and X-ray fluorescence analysis techniques. A particular focus is made on microcomponent composition. Novel data on Cd, Li, Be, Mn, Co, Cu, Zn migration with technogenic flows and accumulation of these elements in alluvia is obtained. It is showed that extraction of valuable components from technogenic waters is a novel problem for refiners that can be solved only in cooperation with mining industry ecologists. Laboratory research of selective copper and zink extraction into corresponding practical products by galvanocoagulation and sulphide precipitation is carried out. Common factors of phase formation are studied using physicochemical modeling, X-ray phase analysis and electronic microscopy. Methods of intensification of processes and increasing of extraction ratio of metals in products are elaborated. A technology of comprehensive processing of undersoil waters is proposed. Enlarged laboratory and pilot plant tests of technological solutions for protecting hydrosphere and extracting metals from mine waters carried out on several plants of UMMC-Holding Corporation showed a possibility of obtaining additional products having weight content of metal which is profitable for consequent metallurgical processing and purification of waters to comply with quality standards. A possibility of transformation of technological chain depending on season variability of water quality is put behind the designed technological schemes.

Jan 1, 2018

By X. G. Liu

Bentonite is an excellent sealant mineral material because of its desirable swelling and self-healing characteristics, low permeability, sorptive qualities, and longevity in nature. A new type of water-swelling building sealant made from bentonite was studied in this paper. The building sealant is prepared by Na-base bentonite, vaseline and paraffin wax under different mass fraction of bentonite (which is 60%,65%,70% respectively). Under unrestricted state, some properties of samples were investigated. The volume expansion ratio at 24 h is 211%, 222%, 256% , and permeability coefficient is 2.86×10-8 cm/s, 4.15×10-8 cm/s and 4.78×10-8 cm/s respectively; low temperature flexibility of the sample (bentonite quality is 65%, 70% respectively) is good, and it does not flow heated for 2 h under 80?. The results of XRD and SEM indicate that bentonite is coated preferably by vaseline, and the spacing of layers of bentonite do not changed. The sample can keep full water swelling ability, and has good molding process. The test results prove that the properties of samples may reach the standard of building sealant.

Jan 1, 2014

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By Alok Tripathy

A simulation code called SIMJIG and the user interfaces have been developed using discrete element method (DEM) and the .NET platform respectively for the jigging process. DEM platform is used for tracking of particles in the jigging operation. DEM uses the net force balance on the particles to track the trajectory of the particle. Simulation results are compared with experimental results obtained by jigging of low grade iron ore lumps. Two different iron ore samples one from Chatishgarh and one from Odisha were used for the experimental studies. The Alljig? stratification test rig meant for batch laboratory experimental studies has been used in the present work. The behavior of different sizes of material on jigging has been examined. Later, the particle size behavior during jigging at different layers of the jig bed has been studied. Further stratification profile across the jig bed has also been studied. It was observed that simulation results are matching quite nicely with the experimental results. The SIMJIG simulator developed in the present study could be used for predicting the performance of the jigging operation effectively. Keywords: DEM, gravity concentration, jigging, iron ore, simulation

Sep 1, 2012

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By Vladko Panayotov, Marinela Panayotova

"Recently, in order to extract metals, the industry is trying to process old metallurgical slag. The material requires very fine grinding that results in enhanced slime-formation. This in turn leads to problems in the course of the flotation process and to a loss of metal. In addition, it causes difficulties in the wastewater treatment aimed at water reuse. The aggregation and separation of the fine particles and their further subjecting to mineral processing would result in more efficient use of raw materials. Closing the water cycle also would be facilitated. The paper presents results from studying sixteen flocculation reagents, commercially available for treating municipal wastewater, including products based on nanotechnology, for their ability to rend the production wastewater in suitable for reuse in the flotation. It turned out that, from all studied reagents, the cationic C-587 is suitable for the purpose. Some of reagents were studied for their ability to flocculate selectively, in presence of coke fines, rich in copper fines which are produced at grinding of a slag from lead-zinc metallurgy. Most promising reagents are chosen, based on the chemical analysis of the flocculated materials. Open-cycle rough copper flotation experiments with the flocculated fines and recycled wastewater gave encouraging results."

Jan 1, 2014

The ball level and pulp load play a key role in the operation of industrial scale ball mills. These two operating variables have a significant influence on the performance of the ball mill and any attempts to optimize these devices require manipulating either one or both of these variables. There are several models that can be employed to perform simulations to optimize the performance of industrial ball mills. However, most of these models require ball load and pulp load measurements as inputs to calibrate the model. The changes suggested by the simulator also provide operating regimes that involve moving either the ball level or pulp load and sometimes both of these variables. A ball mill model coded in JKSimMet was used in conjunction with the Sensomag to optimize the secondary ball mill at Waterval concentrator in South Africa. The results show that the perfect mixing ball mill model can be used in conjunction with the Sensomag to optimize the performance of the secondary ball mill.

Sep 1, 2012

By Hans-Åke Häggblad, Bertil I. Pålsson, Jan Stener, Kent Tano, Andreas Berggren, Pär Jonsén

Numerical modelling of grinding in tumbling mills is traditionally done with the discrete element method (DEM). The grinding balls are then represented by DEM particles and the mill structure is considered rigid. To include more physical phenomena several numerical methods can be combined. One important improvement is to include the mill structure response, using the finite element method (FEM). The interaction between charge and lining can then be studied in detail. The pulp can also be included using a particle-based continuum method e.g. smoothed particle method (SPH). The strength of SPH lies in modelling of free surface flows and very large deformations and it is suited to model simultaneous fluid and granular flow. Still, the coarse particles (grinding balls) in the charge are suitable to be model using DEM. Each of these methods has their strength and weaknesses, but combined they can successfully mimic the main features of the charge movement. With these numerical tools the complex interaction between the different components of the grinding process; pulp, charge, lining and the mechanical behaviour of the mill, can be studied together. This work will present novel numerical approaches to model, simulate and validate charge behaviour in tumbling mills. These numerical models give possibilities to better understand the physical and mechanical behaviour of particulate material systems during grinding in a tumbling mill. This is important in order to develop and optimise future high-capacity grinding circuits and save energy.

Jan 1, 2014

By T. Leißner

This contribution deals with the mineral processing of Li-silicate greisen-type ores comprising of quartz, topaz and zinnwaldite (lithium-rich mica). The origin of the greisen-type ores processed is the Ore Mountains(Germany) where it is explored as a potential resource for the production of lithium carbonate. The goal is to develop a process chain for the enrichment of zinnwaldite using dry techniques only. As basis for the investigation the process chain, which historically was used to process the greisen focused on cassiterite and wolframite, is taken and modified towards the zinnwaldite. Starting with crushed material with particle sizes smaller than 35 millimeters, investigations on different approaches to grinding to liberate mica from gangue are carried out. Concentrates of zinnwaldite are then produced by magnetic separation of size fractions. To assess the success of grinding, classification and separation, mineral liberation analysis and atomic absorption spectroscopy are used. The amount of lithium measured in the sample with atomic absorption spectroscopy was used to calculate the content of zinnwaldite based on its known mineral chemistry. Combined with the particle size distributions, product qualities are determined. Altogether, this allows the thorough evaluation of the success of comminution with focus on following steps of concentration. Keywords: lithium, zinnwaldite, magnetic separation, mineral liberation analysis

Sep 1, 2012

By F. H. Wang

The Yinmao Lead-Zinc Mine Co. Ltd. has got 50 years of mining history. In recent years, the manganese grade in the flotation tailings has been continuously increasing. In order to make fuller use of the existing resources, as well as to increase the company?s economic efficiency, our company adopted the technique ?magnetic separation? and ?iron removal? to effectively recycle the manganese concentrate resources.

Jan 1, 2014

By Silvia Serranti, Giuseppe Bonifazi, Roberta Palmieri

The possibility to develop an efficient recovery and reuse of concrete materials from Demolition Waste (DW) represents one of the main targets applied to end-of-life constructions dismantling/recycling. The need to recycle end-of life concrete materials is strongly increasing in these last years for several reasons: i) the decrease of steady supplies of good quality natural aggregates, ii) the need to secure ample supplies of concrete aggregates to the construction industry and, finally, iii) the environmental constraints limiting the DW wastes disposal. The fulfilment of these goals produces several benefits, that is: i) a reduction of new resources consumption, ii) a strong reduction of the costs linked to transport and energy production, iii) the possibility to utilize materials, otherwise lost (e.g. land filled), iv) land preservation and, finally, v) the reduction of the environmental impact of new exploitation activities. A lot of efforts have been addressed to develop, set-up and apply innovative technologies to maximize DW conversion into useful secondary raw materials. The possibility to utilize efficient, reliable and low cost analytical tools to perform detection/control actions: i) to assess concrete characteristics, before demolition, and ii) to detect the presence of contaminants in coarse aggregates (e.g. bricks, gypsum, steel, glass, plastics, wood, etc.) represent the key issues to fulfil in order to develop innovative process/control actions/procedures inside the DW sector. In this paper a new technology, based on HyperSpectral Imaging (HSI) sensors is investigated to develop suitable and low cost strategies finalised to define and implement innovative smart detection engines for sorting and/or DW flow stream quality control, addressed to perform recovered materials and/or products certification. The proposed sensing architecture is fast, accurate, affordable and it can strongly contribute to bring down the economic threshold above which recycling is cost efficient.

Jan 1, 2014

By Xumeng Chen, Yongjun Peng, Dee Bradshaw

Regrinding rougher flotation concentrates has become a common practice when processing low grade and complex ores. It not only reduces the particle size and improves mineral liberation but also modifies particle surfaces and pulp chemistry due to the strong electrochemical reactions taking place during regrinding. Therefore, the floatability of minerals in the subsequent cleaner flotation is influenced by the regrinding conditions. This paper presents the effect of regrinding conditions on the mineral floatability from both industrial studies in the plant and fundamental studies in the laboratory. Different regrinding conditions were considered, including grinding media, the electrochemical properties of minerals, pulp chemistry (pH, Eh, DO), and breakage mechanisms in tumbling and stirred mills. Results indicate that the selection of regrinding conditions and mill types should not only depend on grinding energy efficiency and liberation but also depend on the surface properties and pulp chemistry produced for effective mineral flotation and separation at the cleaner stage.

Jan 1, 2014