Search Documents

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Joel Moskowitz

In 1990, the United States General Services Administration (GSA) issued a contract for design and construction of a new federal court building in New York City. Mueser Rutledge Consulting Engineers (MRCE) served as Project Geotechnical Engineers. The project site is in the historic government district at Foley Square. It is surrounded by the New York County Courthouse to the west, an existing federal prison building and federal courthouse across Pearl Street to the south and southwest, an office structure to the north, and a residential tower to the east. The interior of the site was crossed by streets which have now been demapped. As with many urban sites, this site was previously occupied by tenement buildings or industrial structures demolished near the turn of the century. Remains of old building foundations were exposed during construction excavation. In addition, buried fuel oil tanks servicing the adjacent courthouse were removed and the usual assortment of urban utilities had to be relocated for the new building foundations. Ground surface elevations vary from about 4.5 to 6 m above the local Mean High Water Datum Plane.

Jan 1, 1996

By Mohamed Hassan, Matthias Seip, Steffen Leppla

In the east of Frankfurt am Main, Germany, a new high-rise building is planned directly next to the river Main. The high-rise building will have a height of about 75 m and will be founded on a Combined Pile-Raft Foundation (CPRF) in the tertiary marl. The new structure will be constructed next to important, sensitive traffic infrastructure. The foundation of the new high-rise building adjoins directly existing historic quay structures, which are more than 100 years old. For analysis of the stability and the serviceability of the heavily eccentric loaded foundation of the new high-rise building and the existing structures and for the investigation of the soil-structure interaction complex three dimensional, non-linear numerical simulations have been carried out. These numerical simulations take into account all geometric and material specific boundary conditions, including the history of the construction of the whole area. The paper introduces into a very complex construction project in which the investigation of the soil-structure interaction has an important role. The three-dimensional numerical simulations are explained and the results are shown.

May 1, 2022

By Axel J. Pollak

Since the late 1960's the Interstate Division for Baltimore City (IDBC) has been planning and developing the Interstate Highway System for the city to meet regional planning goals. The principal goals are to provide convenient access to the central business district and the port while diverting through traffic away from these congested areas. Interstate Route 95, an eight-lane highway carrying north-south traffic, has headed the city's priority list; during the 1970's its construction proceeded steadily from both east and west towards the harbor. Closing the final 8800-ft (2670-m) gap under the harbor will complete Interstate 95's construction. This final portion, known as the Ft. McHenry Tunnel project, will be built in nine construction contracts. Construction costs of the complete project are expected to exceed $700 million, making it the costliest single project in the Interstate Highway System. Full funding is being provided initially by the Federal Highway Administration (FHWA), and the Maryland Department of Transportation will re-pay the 10 percent local share from toll receipts within the first three years of operation.

Jan 1, 1989

By M Muzammil, S. Mukerjee, S. Saran, M. Bharathi

"This paper presents the results of in-situ tests conducted on a set of under-reamed piles in a silty sand deposit. Three piles (i.e. vertical, vertical with one bulb and vertical with two bulbs) of diameter 0.2 m were cast upto a depth of 5 m. The pile cap had four foundation bolts cast into it so that a mechanical oscillatormotor assembly could be mounted centrally on it. The oscillator-motor assembly was used to generate purely sinusoidal dynamic forces, in either horizontal or vertical directions. For both horizontal and vertical vibration cases, it was observed that (i) the natural frequencies decreased with an increase in the excitation force level, (ii) for the same excitation level, the natural frequencies as well as the maximum amplitude of vibration are almost the same irrespective of the pile geometry i.e. number of bulbs in the pile, indicating that the full pile length is not being excited. For the vertical vibration case, the soil-pile stiffness at frequencies, before resonance, were observed to be higher than those at frequencies after resonance. In the horizontal vibration case, the stiffness of the soil-pile system was found to be decreasing with an increase in the excitation force level. The damping ratio was found to be increasing with an increase in the excitation force level.INTRODUCTIONUnder-reamed piles are piles, normally upto a depth of 6 m, with one or more bulbs along the pile stem. These have been used for structures like transmission towers, structures on expansive soils etc. for a very long time, however it is only in the last 30 years that dynamic response of a pile has been studied. Evaluation of dynamic soil-pile interaction is a very complex problem as the conditions and properties of soil are highly variable and unpredictable. Various models and approaches have been suggested by various investigators for evaluating the dynamic soil-pile interaction problem, but most of them are based on the assumptions that the behaviour of soil is linear and the soil surrounding the pile is strongly adhered to it. But in practice, it is not so. The soil surrounding the pile is always somewhat loosened and undergoes some deformation when a sinusoidal load is applied. This causes the soil-pile system to behave nonlinearly.In earlier studies by Novak, (1974), Novak and Aboul-Ella, (1978) etc. a linear elastic behaviour of soil was assumed. This approach was very useful in understanding the mechanism of soil-pile interaction to a large extent. Subsequently various models were suggested like the lumped mass models with nonlinear discrete springs, dashpots and friction elements Matlock et al. (1978), weak cylindrical zone around the pile model Novak and Sheta, (1980), ideal boundary zone model with non-reflective interface, Han and Sabin, (1995) etc. These approximate solutions give an idea about the mechanism of dynamic pile-soil interaction to a large extent. However, in reality both separation and slippage can occur due to the formation of a weak bond at the contact surface between the soil and the pile when a dynamic load is applied. In addition, the soil column adjacent to the pile experiences large deformations under dynamic loads and thus behaves nonlinearly.Some computer aided model studies on the dynamic response of under-reamed piles have been reported, however, very few insitu dynamic tests on under-reamed piles are reported. Dynamic tests on piles were carried out by Novak and Grigg (1976) on small scale single piles and pile groups in the field. Similar field tests on small scale piles were conducted to study the nonlinear behaviour of a single pile and a pile group under strong harmonic excitation by Han and Novak (1988), Han and Vaziri (1992), Burr et al. (1997), Manna and Baidya (2010) etc. The majority of these experimental studies were focussed on the response of the specific pile groups and compared with the results of a single pile. Hence there was a need to study the influence of pile g"

Jan 1, 2015

By Nicolas Denies, Jeroen de Leeuw, Bart Lameire, Jan Maertens, André Vervoort, Flip Hoefsloot, Noël Huybrechts, Flor De Cock

"In recent years, the Deep Mixing Method has increasingly been applied for the construction of earth and water retaining structures. From practice, it has been experienced that there is a real need to develop execution and design rules adapted to the function of the soil mix wall (retaining wall, water barrier, foundation solution or a combination) including the temporary or permanent character of the application. Based on the results of the BBRI Soil Mix project (2009-2013), a design approach has been developed in collaboration with the SBRCURnet. The present paper briefly discusses the principles of this design approach which takes into account the function of the soil mix wall and the characteristics of the soil mix material. The interaction between the soil mix material and the steel reinforcement can be considered in the calculations depending on the function of the soil mix wall. Design and quality control requirements are given in function of the application and take the lifetime of the structure into account. Durability aspects of the soil mix material are therefore considered in the present design approach.INTRODUCTIONSince several decades, the deep mixing method is used for ground improvement works. A more recent application is the use of soil mix as structural elements such as in the case of the earth-water retaining soil mix walls. Since 2000, due to the economic and environmental advantages of the method, this particular application has shown an amazing growth in Belgium and in the Netherlands. A typical excavation (16 m depth), realized with CSM (Cutter Soil Mix) panels, is shown in Fig. 1. For temporary applications, the questions related to the mechanical characteristics of the material, its permeability and its adherence with steel have been investigated with success within the framework of the BBRI Soil Mix project (2009- 2013) (see Denies et al. 2012 for more details). The durability of the soil mix material remains a complex topic while permanent applications are more and more observed in practice. In order to define an obvious design approach, it was necessary to clarify the potential functions of soil mix walls and to establish the requirements related to their design and construction. The BBRI (in Belgium) and SBRCURnet (in the Netherlands) have therefore worked together to publish guidelines in the form of a handbook titled ‘Soil Mix Walls’ (publication foreseen in 2015). In this handbook, a methodology is proposed for the design of the soil mix walls for which the interaction between steel and soil mix can possibly be taken into account dependent upon the application. Each potential function of the soil mix wall is described (e.g. earth retaining wall, cut-off wall, etc.) and the temporary or permanent character of the application is always considered."

Jan 1, 2015

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Matthias Baeßler, Markus Herten, Ernst Niederleithinger, Steven Georgi

"Abstract: BAW and BAM have performed a large scale comparison and calibration test on static and dynamic load capacity evaluation of bored piles in glacial sandy soil. The test was performed using eight piles at the BAM test site for technical safety at Horstwalde 50 km south of Berlin. The test area has been prepared and investigated in great detail using boreholes, cone penetration tests, pore pressure sensors and geophysical methods to assure controlled conditions for all piles and tests. The piles (10 m length, 0.9 m diameter) are mainly friction piles (low toe resistance) and have been checked by integrity testing. Five piles have been tested by five contractors using the dynamic method in a blind experiment, the other ones piles by static load and/or later on by the dynamic method. Some piles have been equipped with additional fibre optic instrumentation which proved to be robust and helpful in interpreting the results of static, dynamic and integrity tests. We have experienced a deviation of the dynamic load test results gathered in the blind experiment from the static values of up to 20% in most cases, sometimes even up to 30%. This can be related to the known soil inhomogeneities, interpretation and modelling in CAPWAP and method inherent uncertainties. In cases where the static values were known by the testers for calibration, the deviations were significantly smaller. It has to be taken into account, that the two static load tests showed different results as well. Due to the low toe resistance, use of a big drop weight (11 tons) and large drop heights most piles suffered from cracking, which was clearly seen in follow up integrity tests and confirmed by excavation. The piles are available for further research.IntroductionBored piles are used in many construction projects of the German waterways authorities, e. g. bridges, piers or locks. Their load carrying capacity varies with pile type and geometry as well as soil type, parameters and structure and is thus not easy to calculate in advance. Dynamic pile testing as a cost effective addition or replacement for expensive load tests is accepted in many places (Beim and Likins 2008) but still doubted in others. Inspired by the international prediction event for piles in residual soil carried out in the frame of ISC’2 (Viana de Fonseca and Santos 2008), governmental research institutes have designed an experiment in a geological setting typical for glacial and post-glacial areas in northern Germany. Some results have already been presented by Niederleithinger et al. (2012), Herten et al. (2013) and Baeßler et al. (2013). It was intended to perform a blind test for load capacity estimation using dynamic pile testing on six drilled shafts involving five test crews. Two other piles would have to be tested thereafter using static and dynamic methods."

Jan 1, 2014

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By M. Hesham El Naggar, Osama F. E. Drbe

"Abstract: The use of micropiles has greatly increased the last twenty years, including applications involving low capacity micropile networks, seismic retrofitting, underpinning of existing foundations and high capacity foundations for new structures. This paper presents a field study of the behaviour of single hollow core micropiles in firm to stiff lean clay. Eight micropiles were installed using hollow bars (76 mm OD and 48 mm ID) with air/water flushing technique and advanced to a depth of 5.75m: six micropiles were installed using 228 mm (9 in) drill bit and two micropiles were installed using 178 mm (7 in) drill bit. All micropiles were instrumented with linear potentiometers to measure the vertical displacement of the micropile head and vibrating wire strain gauges to measure the axial strain at three points along the micropile length. Twelve full scale tests were conducted on the eight micropiles, four monotonic compression, four cyclic compression and four tension tests. Only the results of micropiles tested under monotonic compression is presented in this paper. The full scale load tests and a comparison of the performance of the micropiles with 228 mm and 178 mm drill bit are presented and discussed in terms of load-displacement curves, bond strength and tip resistance. The results showed that the proposed values of bond strength in FHWA give a conservative design of the hollow core micropiles. The micropiles constructed with 228 mm drill bit performed marginallybetter than the micropile with 178 mm drill bit in terms of the ultimate capacity.IntroductionMicropiles have been defined in a variety of ways, but can universally be classified as small diameter (less than 300mm), bored, and grouted in place piles (FHWA, 2005; Bruce et al., 1999; and Scherer et al., 1996). They can sustain axial (compression and tension) and/or lateral loads. Dr. Fernando Lizzi used micropiles in 1952 for underpinning of historic buildings damaged during World War II (Bruce D. A., 1988). Since then, micropile applications have expanded rapidly to include underpinning for existing foundations, in situ reinforcement, and seismic retrofitting and foundations for new construction. In particular, micropiles have graduated from use in low-capacity micropile networks toapplications as single high-capacity foundation.Micropiles capacity is affected by the construction technique, which involves drilling, placing reinforcement, and placing or pressurizing the grout. For example, the drilling method influences the degree of bonding between the grout and the ground, and the placement of reinforcement and the choice of grouting method have an impact on the development of the bonding. Bruce et al. (1997) showed that grout/ground bond is most affected by the grouting method. Based on the type of pressure applied during the grouting process, micropiles are classified as follows (FHWA, 2005): Type A: grout is placed under gravity pressure only using either sand-cement mortars or neat cement grout. Type B: pressures typically in the range of 0.5 MPa to 1 MPa are applied in order to inject the neat cement grout into the drilled hole while the temporary drill casing is withdrawn. Type C: involves two-step process; neat cement grout is first placed in the hole under gravity pressure head only as in type A, and prior to the hardening of this primary grout, a similar grout is then injected via a preplaced sleeved grout pipe at a pressure of at least 1 MPa. Type D: like type C, this type is a twostep process: neat cement grout is placed in the hole under gravity pressure head only (but pressure could be applied in some cases), additional grout is injected via a sleeved grout pipe at a pressure of 2 MPa to 8 MPa once the primary grout has hardened. In some cases, a packer is used inside the sleeved pipe, enabling specific horizons to be treated. Recently, Type E micropile is proposed, which involves"

Jan 1, 2014

By Alper Turan, Hesham El Naggar

"The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers. INTRODUCTIONThe schedule and cost limitations imposed by the traditional over-excavation and replacement method for the stabilization and settlement control for poor soils resulted are underlying factors for the significant increase in the use of aggregate pier foundation system, particularly in the last two decades. Various well known advantages of aggregate pier systems including increased bearing resistance, settlement reduction, and increased uplift capacity have been studied by various authors. The use of aggregate pier systems for settlement control in soft soil deposits was studied by various researchers including Lawton and Fox (1994), Lawton et al. (1994) and Wissmann et al. (2001). Lien and Fox (2001) studied the behaviour of aggregate pier systems supporting embankments and retaining walls. The stabilization of slopes by means of aggregate piers was studied by Lien and Fox (2001), Wissmann et al. (2002). Thompson et al. (2009) reported on a performance monitoring study of aggregate pier systems supporting MSE walls. The interaction mechanism between the aggregate pier system and the surrounding soil attracted attention of various researchers. Handy and White (2006a) and (2006b) studied the changes that occur less than 2 m from centers of the piers, and further away, respectively. The support mechanism of aggregate pier systems subjected to compressive loading were studied experimentally and numerically by White et al. (2007) and Pham and White (2007), respectively."

Jan 1, 2017

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By Terrence R. Udland, Russell D. Call

"Honored with a DFI 2006 Special Recognition Award, the Four Bears Bridge was constructed across Lake Sakakawea and opened to traffi c in September 2005. The very large lake size and severe winter conditions required an effi cient foundation design capable of resisting extreme ice loading and able to be effi ciently constructed in waters up to 90' deep (27.4m).DESIGNING FOR EFFICIENCYLocated in a remote area of North Dakota, the Four Bears Bridge replacement was a major undertaking for the North Dakota Department of Transportation, with dual goals of providing a new structure that would endure a severe environment, while enhancing the natural beauty of the area. Competing bids would achieve the best price for the owner, challenging the design team to creatively solve the engineering challenges unique to the site. Foundations for North Dakota’s new Four Bears Bridge had to accommodate water level fl uctuations of up to 40 feet (12m), along with extreme ice loading and be effi cient in order to be the low cost solution at the time of bidding. All three major criteria were achieved through the use of an effi cient ‘fl oating’ lost precast concrete cofferdam founded on steel pipe piles, which allowed the contractor to achieve the project schedule. The result is an award-winning bridge that is contextually sensitive to the environment. The bridge aesthetics pay tribute to the Three Affi liated Tribes, the Mandan, Arikara and Hidatsa, who reside on the Fort Berthold Indian Reservation, adjacent to the bridge site.The original Four Bears Bridge was located over the Missouri River near Elbowoods, the native grounds of the Three Affi liated Tribes. Construction of the Garrison Dam in the early 1950’s created Lake Sakakawea, a fl ood control project on the Missouri River, and resulted in the area being fl ooded. The bridge, along with many tribal members, was relocated to a site near New Town. The bridge provides the primary crossing of Lake Sakakawea and is a critically important transportation element for the residents of the Fort Berthold Indian Reservation. The relocated bridge had become functionally obsolete and not replacing it would require a detour of 170 miles (274km). The North Dakota Department of Transportation determined that it should be replaced. In order to achieve the most effective solution, the North Dakota Department of Transportation selected a design team responsible for the creation of competing steel and concrete designs that were competitively bid. The design team was led by Kadrmas Lee & Jackson, with FIGG responsible for the concrete bridge design, while Lichtenstein Consulting and Kadrmas Lee & Jackson completed the alternate steel bridge design."

Jan 1, 2007

By the courtesy of Metropolitana Milanese (Milan Underground), roost of the delegates visited on April 12, 1991 the tunnel of "PORTA VENEZIA" STATION of MILANO RAILWAY LINK. The "PORTA VENEZIA" STATION will be the most important in the link and it will he also the largest underground project of the whole railway transport network in Lomhardy. The particular conditions of the soil and the collocation of site in the center of Milano have required new technologies and the technical solution applied to this job is called "Cellular Arch Method" by its designer Prof. P. Lunardi. Our sincere thanks go to Prof. P. Lunardi and Eng. E.M. Pizzarotti of Rocksoil, Milano who have kindly furnished us a technical description of this method. Eng. Pizzarotti was the guide during the visit and gave all the technical explanations to the delegates. THE "VENEZIA" STATION IN THE 2PB SECTION OF THE RAILWAY LINK The excavation of cavities in loose ground, exceeding a certain dimension and at shallow depth, is not feasible using traditional methods: in fact it is not possible to consolidate the ground around the cavity in such a way that homogeneity and resistance is sufficiently guaranteed.

Jan 1, 1994

By Fabrice Mathieu

The Cutter Soil Mixing (CSM) provides a cost effective solution for the rapid construction of retaining and cut-off walls using new equipment developed from diaphragm wall cutter technology. CSM consists of cutting and mixing drums mounted on compact hydraulic motors. Soletanche Bachy CSM has been designed to leave the space above the tool free, thereby mixing the soil efficiently during all the phases of the wall construction, with high penetration rates. The precise positioning and verticality of the wall is achieved using a kelly bar and full monitoring. Soletanche Bachy CSM is a versatile equipment which can be mounted on various carriers: pile rigs, hydraulic crane, carrier equipped with telescopic mast. The major phases of Soletanche Bachy CSM development are presented, including the results of an extensive trial carried out in Le Havre (France). The soil consists of hydraulic fill with soft soil lenses overlying sandy deposits. 20m deep panels were constructed to support a rectangular shaft. During the construction, and after its completion, the shaft was subjected to an extensive series of tests followed by a partial excavation. The paper discusses also the future development of the technique and its potential applications.

Jan 1, 2006

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By Brian W. Wilson

A case study is presented that describes the design and implementation of a combined blast densification and deep dynamic compaction program which was undertaken to improve the foundation soils for a proposed tailings dam raise in Ontario, Canada. Based on the results of the geotechnical investigation it was determined that the foundation of the dam would be situated on tailings of both variable thickness and density, much of which would be susceptible to liquefaction under the design earthquake for the region and type of facility. Blast densification trials were completed by the owner and the results of these made available to prospective tenderers in response to a call for a fixed price contract for the design and implementation of a densification program for approximately 800,000 m3 of foundation tailings. The variation in tailings gradation and the impacts of such on the ground improvement program are discussed, as are details of both the additional blast densification field trials completed by the contractor, and the selected blast pattern and explosive charging used for production blasting. The applicability of the various ground improvement techniques to the actual conditions encountered, and the results obtained are also discussed.

Jan 1, 2010

By Paul Doherty

It is known that the axial capacity of a displacement piles installed in clay varies with time. Consolidation theory suggests that dissipation of porewater pressure set-up during pile installation would lead to increased effective stress and hence higher pile resistance. In recent years a number of case histories have reported time dependent capacity increases for piles installed in sand. Although there is some debate regarding the physical mechanisms controlling this phenomenon, known as ageing, it is unrelated to pore pressure dissipation as piles in sand are installed in primarily drained conditions. A series of field tests designed to investigate ageing effects in soft clay are presented in this paper. Full-scale load tests on 6m long 250 mm square concrete piles, which were driven into soft clay are described. The piles were first tested approximately 100 days after installation, at which stage full equalization of the excess pore pressures had occurred. Static load tests were then performed up to 10 years after pile installation. The piles exhibited significant ageing, with their shaft resistance increasing by up to 66% over a 10 year period. Possible mechanisms for such aging characteristics are explored.

Jan 1, 2011