Search Documents

By Bengt H. Fetlenius

The "Pile Prediction Event" at the ASCE GeoInstitute's Deep Foundation Conference in February 2002 involved prediction of drivability and capacity of three 14m long, 324mm diameter, closed-toe pipe piles driven into loose to compact fine sand to slightly silty sand. Predictors were provided the results of two soil borings and three cone penetrometer tests, as well as type and model of hammer to be used for the pile driving. A total of 33 persons submitted predictions. As to penetration resistance distribution, many predictions were far below actually observed values. As to capacity in compression, the predicted values ranged from 270KN through 2,340KN with a mean of 1,070KN. As to capacity in tension, the predicted values ranged from 100KN through 1,650KN. The maximum load applied to the compression pile in the static loading test was 1,25OKN, at which no more reaction load was available. The reaction system for the tension test failed early in the test. CAPWAP analysis on End-of-Driving blows showed capacities at the end of the driving for the push and pull piles of 670KN, and 710KN, respectively. No restrike tests were made. Additional CPT soundings indicate that the pile driving had densified the soil. Static analysis and calculations from the CPT indicated that capacities ranged from 1,000KN through 2,000KN. The paper presents the data and discusses the various methods of determining pile capacity and addresses influence of set-up Lessons useful for future similar events are indicated.

Jan 1, 2004

By John F. Spence

Ever since opening, the M25 motorway to the west of London has carried a rapidly increasing volume of traffic. The section of M25 between the junctions with the M3 and M4 motorways, which is in the near vicinity of Heathrow airport, is the most heavily trafficked section. Piling and ground treatment was required for motorway widening works over this route, which is 7 miles long. The foundation works were undertaken next to the live motorway and beneath the flightpath for aircraft landing and taking off at the airport. The paper describes the foundation construction techniques used, and the how the methods were affected by the live motorway and the height restrictions imposed by the airport. A unique method of piled retaining wall construction is also described.

Jan 1, 2007

By Peter J. Jancich

This paper describes the installation of high capacity Augered Pressure Grouted piles which support structural loading from a four level parking garage in west-central DuPage County, Illinois. The subject site is characterized by a variable glacial geology which presented, to the designer, a number of problems with respect to analysis and prediction of pile capacities, and, to the contractor, the very real difficulties associated with estimating the costs of, and installing foundation units in highly variable subsurface conditions. 2. General Site and Subsurface Conditions 2.1 Site Conditions - The subject site is part of an overall 300 acre property. Topographically, the overall site is saddle shaped with higher elevations along north and south boundaries and a subdued, east-west trending swale centrally located. Elevation relief is on the order of 25-30 feet (7.6-9.2m).

Jan 1, 1991

By P. M. Deshpande

An interactive short column system is evolved as alternative to deep foundation system in deep layers of marine clay, the interaction of encased stone column and marine clay carry load without causing conventional settlement. This paper presents concept of the system and its field application as foundation of culverts on marine clay layer of 15 to 17 M underlain by residual soil layer of 5 to 6 M, where conventional pile of 23 to 25 M would have been required.

Jan 1, 1996

By B. Ramanathan

The results of a pile load test on a 1200 mm dia and 25 m long bored Cast-in-situ pile in soft rock is reported. The subsoil has a high N value of above 60 from 7 m to 21 m. The soft rock was observed below 21 m and N value exceeded 100. The theoretical calculations showed that the safe carrying capacity will be about 410 t. But the actual load test on the pile indicated that the allowable load is only about 140 t. This is attributed to the fact that the soil is cemented and loses strength due to remoulding caused by pile installation. It is concluded that great care should be exercised in determining the carrying capacity of piles in cemented soils and soft rocks and that 'N' value alone should not be used.

Jan 1, 1996

By Shawna Munn, Nadir Ansari, Toben Jerry

With ever increasing demands on space in urban environments and smaller available footprints, buildings are being designed to increasing heights to meet the need. This case study discusses the increasing challenges in developing projects within urban environments with smaller available footprints and increasing building heights. The One, Canada’s tallest residential building under construction will stand at 85 storeys and is located at one of the most prominent and built up intersections in Toronto, Yonge Street and Bloor Street. This led to many challenges in design and construction of the shoring and foundation work, including the required design capacity of the foundations for the supertall building and proximity of the large diameter drilled shafts to the excavation shoring wall. This case history describes the shoring design option evaluation, performance, and lessons learned to date throughout construction of the building foundations within a small congested site. PROJECT OVERVIEW The One, Canada’s tallest residential building under construction by Mizrahi Developments, is a supertall building that will stand at 85 storeys and 306 m (1005 ft). The first 18 floors will be comprised of retail, restaurants, and hotel with luxury residential condominium units in the tower above. The project is located on the Southwest corner of Yonge Street and Bloor Street, one of the most prominent and built up intersections in Toronto. The L-shaped excavation measures 58 m by 47 m (190 ft to 154 ft) and ranges from 22 m to 28 m (72 ft to 92 ft) in depth with one internal corner projecting 11 m (36 ft) into the site.

Jan 1, 2019

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

By Eric R. Borys, Amaneh E. Kenarsari, Brett Gitskin

This case study discusses impacts of excessive Earth Retention System (ERS) lateral movement at a project in city of Chicago. The ERS (cantilevered sheeting) moved inward towards the excavation and caused lateral displacement and cracks in six drilled shafts located about 1 to 2 lateral feet (0.3 to 0.6 m) from the face of the sheet pile wall. Up to 9 inches (23 cm) of horizontal movement was observed on top of the supporting sheet-pile. Similarly, survey measurements showed the top of the drilled shafts moved laterally up to 8 inches (20.3 cm). To evaluate the cause of failure and determine a remediation solution, the soil, shaft and site conditions were investigated. Pile Integrity Tests (PIT) were conducted at the affected drilled shafts. The shafts with identified anomalies were cored and video-recorded. The cause of the failure was determined to be related to variable soil conditions across the site, deeper excavation (i.e., increased effective ERS wall height), and other differences between design and as-built conditions. Internal bracing, in the form of walers and rakers, was installed to limit further movement of the sheet pile as a short-term solution, with additional grade beams framed into the basement slab-on-grade as a long- term solution. Five of the six cracked shafts were spliced with reinforcing bars and high strength grout and one shaft was replaced. INTRODUCTION The subsoil in the Chicago Area mostly consists of glacial till clays underlain by water-bearing granular soil over bedrock. The glacial clays have very soft to medium consistencies for a typical thickness of 30 to 50 feet (9.1 to 15.2 m) below which hard clays (Hardpan, i.e., heavily over-consolidated clay soils) are encountered. The soft clays are often referred to as the “Chicago Blue Clay”. Beach Sands are also found above upper soft clays in several areas, especially within a three-mile strip near Lake Michigan (Peck and Reed 1954). Due to the existence of soft clay in Chicago area, supporting the mid to high rise buildings on drilled shafts extended to Hardpan is a common practice in modern building design. In the early 19th century it used to take about 3 weeks to excavate 1 shaft hole and about 1½ days to fill the shaft with concrete in Chicago (Manierre 1916). The early 19th century methodology of excavating a shaft consisted of hand digging the shaft, installing wood lagging as temporary shoring with spoils removed with a rope and pulley system from the surface. Today, the excavation of a typical drilled shaft in Chicago uses heavy drilling equipment and requires much less time for excavation and concrete placement. It is not uncommon for contractors to excavate shafts and place concrete at a rate of about 2 to 5 drilled shafts per day (with one drill rig).

Jan 1, 2018

By X. L. Chen

The diaphragm walling has been recently adopted in one of the largest excavation of deep foundation engineerings in Shanghai, China with dimension of 90m in length, 50m in width and 13m in depth to solve its stability problem. In this paper the field test for monitoring the stability of the diaphragm wall is discribed, in which the excess pore water pressure and the horizontal displacement of the clay layers were monitored during the period of the excavation. The data measured in the field test are efficient for the safety during construction.

Jan 1, 2010

By Michael Arnold, Bob Faulhaber, Joe Nichols

"Center Hill Dam is a critical part of the infrastructure controlling floods at the Caney Fork River and reducing flood levels at the Cumberland, lower Ohio and Mississippi Rivers. The Center Hill Dam Foundation Remediation Project was necessary to address Karst features in the foundation rocks and observed signs of distress of the dam. From 2011 to 2014 BAUER Foundation Corp. (BFC) performed deep foundation works for this project. The executed features of work include the installation of two walls. The first wall extends throughout the clay embankment into the underlying rock to provide encasement during the construction of the second wall. Its width of 7.4 feet makes it the widest diaphragm wall ever installed. The second wall is the actual seepage barrier and provides a continuous 2- feet wide wall. It extends through the first wall into the underlying rock and is up to 300 feet deep. The paper introduces the project, the requirements specified by United States Army Corps of Engineers (USACE) for encasement and barrier wall and the approaches taken by BFC. It discusses the ground conditions and describes the excavation equipment as well as the excavation methods used. A special focus is put on the steering capabilities of the hydrocutter equipment and the verticality performance.PROJECTBeginning in 2011, BFC was tasked by the USACE with the installation of a seepage barrier/cutoff wall at the Center Hill Dam Foundation Remediation project under a partially performance based specification. The remediation was necessary due to karst features in the foundation rocks and observed signs of distress, which led USACE to rate the dam with the most critical dam safety action classification (DSAC I). The executed features of work include the installation of two walls. The first wall, an encasement wall, extends vertically through the clay embankment and is embedded minimally into the underlying bedrock to provide embankment stability during the construction of the second wall, the barrier wall. The encasement wall is constructed of overlapping panels 7.4 feet (2.25 m) wide, which is the widest diaphragm wall ever installed, and up to 210 feet (64 m) deep. The second wall is the seepage barrier and provides a continuous 2 feet (0.6 m) wide wall consisting of overlapping panels. It extends through the encasement wall into the underlying bedrock and is up to 307 feet (93 m) deep. BAUER BC40 and BC50 hydrocutters mounted on MC96 and MC128 foundation cranes were used to perform the majority of the works (Figure 1). Excavations were performed under bentonite slurry (encasement wall) and water (barrier wall) and concrete was poured with the tremie method. Adding to the challenges, the project had to be executed in an environmentally sensitive area. Based on the high risk, a special focus was put on monitoring, quality control and geometric accuracy. The WallTracker information management system was used to share all relevant data between BFC and USACE (Roff et al. 2014)."

Jan 1, 2017

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

By Nabil F. Ismael

The axial capacity of step tapered bored piles in sand was examined by field tests at one site in Kuwait. Two straight piles, and two step tapered piles were load tested in compression to failure. All four piles were 3 m deep. The straight piles were 0.2 m in diameter. The step tapered piles had a diameter of 0.3 m for the upper segment which extended up to 40% of the pile length changing to 0.2 m diameter for the lower section. The soil profile consists of medium to dense sand with minor cementation and no groundwater was encountered. Both the ultimate bearing capacity and the settlement at working loads were examined. The axial capacity of the step tapered piles was greater, and the settlement at working loads was less, compared with the straight shaft piles. The increase in capacity is mainly attributed to the added side friction along the larger diameter top segment of the shaft.

Jan 1, 2008

By Vijay Kumar, Serhat Baycan, Karsten Beckhans

For the deep foundation of podium and tower of the Kuala Lumpur City Centre, BAUER (MALAYSIA) SDN. BHD. constructed 225 bored piles with diameter range of 2.0 to 2.5 m. In order to comply with the depth requirement of the design, for planning purposes and preparation for site, the drilling equipment was required to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to; controlling the open hole stability over time with polymer, installing 70-ton heavy steel cages, pouring up to 550 m³ concrete continuously, in conjunction with installation of kingposts into workable, fresh concrete. The piling works were executed with a BG 72, the biggest drilling rig globally available, and the stringent verticality of the pile bore holes which required approval prior to cage installation. For verification of verticality, Bauer’s patented Drilling Inclination System was successfully used.

Nov 1, 2022

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Dario Libano, Franz-Werner Gerressen

"Diaphragm walls are known as underground structural elements commonly used for retention systems and permanent foundation walls or elements. Of course they can also be used as deep groundwater barriers. This paper will focus on the construction work in an urban area like Sao Paulo. The Line 5 of Metro Sao Paulo is one of four network expansion projects undertaken at the same time. The projects will cover various areas of the city. The Line 5 on São Paulo’s south-side will be extended 7.1mi (11.5km) to serve 770,000 riders per day, stretching a total of 12.4mi (19.9km) along 17 stations. The extension line will facilitate access to the city’s central section and the commercial and hospital districts located along the line. The Brooklin Station, subject of this paper, had to be carried out in a special five shaft shape design, shaft diameter 131ft (40m) each, without using ground anchors. A focus will be taken on the special requirements of the installation of the arrows as well as on the specialties of installation for the shaft shaped layout. Therefore, it was required to install a 3.3ft (1,000mm) diaphragm wall using a specific layout especially in the connecting sections of the shafts, the so called arrows, to provide a bearing area for the struts. Maximum wall depth was about 121ft (37m); the total volume was about 20,060 cubic yard (15,337m³). The paper will describe the construction method and the sequence of activities required for the construction of this diaphragm wall using a combination of hydraulic grab and trench cutter system.INTRODUCTIONThe Line 5 Extension, in the city of Sao Paulo/Brazil, is currently the most important investment in public transport by Sao Paulo state’s government. It will connect the south part of the city to the city center, crossing through four other major METRO lines and stations, all currently in operation. The extension includes a new parking yard for the trains and 11 new stations. The Brooklin Station is one of the new stations and has a unique geometry of five secant shafts. The station should open and operate in 2016.The original design included constructing five secant shafts stabilized by two plastic slurry walls using conventional grab technology. One of them was to contain the contamination plumes in the neighborhood and the other for temporary support to enable the excavation of the shafts. The final retaining wall design was reviewed and changed to a concrete structural diaphragm wall. The reason of design change was as well the reduction of construction time of the shafts by half to meet the schedule as to avoid dewatering effects in a geological region characterized by Quaternary sediments and environmental contamination plumes. It was the first time that a trench cutter (hydromill) was used in such a situation in Brazil. The cutter increased the quality of the joints by overcutting, and decreased the probability of having seepage into the shafts. The cutter created a seepage barrier and avoided movement of contamination."

Jan 1, 2017

By Abid O. Adekunte

The design, construction and monitoring of the deep excavation support for the basement of a large-scale commercial development in Cavan, Ireland is presented. Excavation area was adjacent to existing structures and retained height H varied between 4.0m ? 11.0m. In areas where excavation depth H < 5.0m, wall was designed as cantilevered section. However in sections where 5.0m = H = 11m, additional wall supports were required for serviceability reasons. Traditionally, designers often provide additional wall support through the use of tie-back ground anchors, raking props and braces. On the current project, the main contractor was not in support of the use of temporary props so as to maximise working space, while owners of adjacent properties disapproved the use of tie-backs. The limited set-back between the wall line and site boundary also contributed to the complexity of the project. A rare alternative solution has been adopted. This novel approach involved buttressing the wall with steeply raking bored tension piles at regular intervals along the wall. Comparison of the monitored deflections in the cantilevered sections with those recorded at sections where tension piles were used shows the novel solution to be safe and quite effective. This approach is also considered to be more economical when compared with ground anchorage and propping.

Jan 1, 2008

By Venugopal Bonani, Kumaran M., Thomas John

Liquid storage tanks are usually located in nearshore or coastal regions with soil profiles containing thick layers of compressible soils. These storage tanks are usually of large diameter up to 90m and carry high loads, and the tanks are supported by heavy deep foundations such as piles. These structures are subjected to huge lateral loads due to wind and earthquake, and any damage to storage tanks with highly inflammable liquids leads to disastrous condition. So, it is important that the top layer of soil (up to the fixity depth) should be strong enough to provide the required lateral load capacity to the pile. In a project for constructing LNG terminal in Odisha containing 2nos of 89m diameter LNG storage tanks supported with pile foundation located near to coastal region, for improving the lateral capacity of existing soil, the top 3m was replaced with compacted engineered fill (GSB). The site was a filled-up area with dredged soil from seabed, the top 5m-10m were soft to medium stiff clay with SPT N less than 10. The lateral design load on pile was 534kN under free head condition. Actual lateral capacity for the strata was around 200kN under free head condition which was less than required capacity as per structural requirements. Therefore, for improving the lateral capacity of pile the top 3m soil is replaced with well compacted engineered fill (GSB) in layers of 150mm and the capacity is proved by conducting initial and routine lateral load tests. This paper describes the properties of the engineered fill used and how the lateral load capacity of pile was improved to meet the design requirement.

Sep 1, 2022

By Mario Terceros H., Bengt H. Fellenius

"ABSTRACTFour strain-gage instrumented bored piles were constructed in a sedimentary, dense to very dense, fine to medium sand in Santa Cruz, Bolivia. Two of the test piles were the normally used bored pile constructed with bentonite slurry and two piles were Bauer Full Displacement Pile (FDP). One of each pair was equipped with the Expander Body, an inflatable steel cylinder that on pressure-grouting provides an enlarged pile toe. Head-down static loading test were performed on three of the piles and a bidirectional test was performed on the fourth pile, a standard pile with Expander Body and a bidirectional cell placed immediately above the EB. The latter pile was tested in 3 phases. First by activating the cell, second, by a head-down test, and, third, by a repeat bidirectional cell test. The static loading tests proved the shaft resistance of the FDP pile to be about twice that of the standard bored pile and that the Expander Body more than doubled the toe stiffness. The strain-gage records showed that the standard bored piles had multiple bulges and neckings, which affected the evaluation of the axial stiffness and load distribution of the piles. The testing programme was used for a prediction event with 60 persons, ahead of the tests, submitting predictions of the load-movement curves for the test piles and also a capacity appraised from the curves.1. INTRODUCTIONOn April 23 - 26, 2013, the First International Conference and Seminar on Deep Foundations was held in Santa Cruz, Bolivia under the auspices of INCOTEC SRL, the UAGRM University, and the Bolivian Association of Civil Engineers and Chamber of Construction. To coincide with the conference, a research study on construction and static and dynamic testing of four instrumented bored piles was undertaken. To ""add spice"" to the conference, a prediction event was organized on the test programme. This paper presents the soil conditions at the site, the type and construction of the test piles, the outcome of the prediction event, and the results of the static tests.2. SOIL CONDITIONSGeotechnical studies comprising SPT and CPT tests with routine laboratory analysis were performed on recovered soil samples. Three SPT boreholes were put down at three of the locations of Pile TP1, TP2, and TP3, at 5.0 m distance from each other. The SPT procedure consisted of manual hoisting of the weight by three crew members pulling on ropes over a pulley supported by a tripod and letting the weight fall by gravity. The groundwater table lies at 3.5 m depth.Figure 1 shows diagrams of the SPT N-indices and the distribution of water content in the three boreholes. The SPT-indices show the soil density to be compact. The average water content is about 15 %, plus-minus a few percent."

Jan 1, 2014