Search Documents

By G. A. Kosick, G. S. Dobby, O. Matwijenko

"A 100 kg/hr portable flotation pilot plant has been operated at Kidd Creek Mines with the objectives of:(a) determining performance expected by column flotation circuits on primary zinc and copper cleaning, and (b) evaluating column flotation circuit configurations.The self-supporting pilot plant, owned by Minnovex Technologies Inc. and operated by Minnovex and the University of Toronto, consisted of three 16 cm diameter by 6.5 m high columns and a bank of four Denver No. 7 cells. It was configurable to any arrangement using these four (or fewer) units. The columns were controlled through the use of multiple pressure transducer measurements. This paper presents the approach to testing and the results of more than 70 circuit tests. INTRODUCTIONThe integration and retrofitting of flotation columns within existing mechanical cell flotation circuits is becoming a common occurrence. The correct approach to this integration, however, is often difficult to define, due to a scarcity of previous experience and the difficulty in predicting column circuit performance. In most cases, the effect of column implementation has been experimentally assessed using a single pilot column, with the consequence that selection of an appropriate circuit to implement is difficult. Important considerations are the impact that column water addition will have on the existing operations, and the differences between mechanical cell and column performance in integrated cleaning circuits.To address the problem of circuit selection a portable flotation pilot plant, consisting of both columns and mechanical cells, was designed and constructed by Minnovex Technologies. The pilot plant was structured for complete flexibility of circuit configuration, with the intent to provide a means by which both research and plant personnel could determine the best possible column circuit configuration for a given application."

Jan 1, 1990

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

By Gregg S. Hill, Bert J. Huls

"This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed us to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flow sheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit. Details of the technology behind each unit operation will be presented in later publications.INTRODUCTIONSince 1996 BHPBilliton and MEL (Minera Escondida Ltda.) have developed a process to recover copper from coarse particles in the rougher tailings. Copper recovery from fresh tailings is not new. Several operations in Chile, such as Chuquicamata, El Teniente (AMEC, 2003), Mantos Blancos and others have operated various forms of tailings circuits. Both Chuquicamata and El Teniente practice cascade flotation scalping off froth containing fine copper particles after allowing sufficient retention time, air inducement and, sometimes, additional reagent addition. Chuquicamata tailings are not segregated but floated in sequential cascade and conventional large cell arrangements. At the Valle Central operation of El Teniente a coarse fraction of mill tailings is ground and floated, with the rejects recombined with fine tailings and subjected to cascade flotation through a sequence of concrete launders as the tailings flow towards their final deposition area. Mantos Blancos cyclone the rougher tailings and blend the underflow with scavenger concentrate from elsewhere in the principal circuit prior to flotation in Wemco Cells. Kemess in BC, Canada operates a 160 m3 Outokumpu cell to reduce the tailings sulfur content (Rasmussen, et.al, 2004)."

Jan 1, 2005

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By M. Sukhram, S. A. Argyropoulos

"In the aluminum and steel processing industries there is a need for velocity sensors to measure the flow characteristics of liquid metal. This paper will present a sensor and an inverse heat transfer technique to determine the direction of velocity in flowing liquid aluminum. Experimental research work with the sensor involving liquid aluminum was conducted, using the Revolving Liquid Metal Tank at the University of Toronto, which rotates 50 kg of liquid aluminum with velocities up to 0.35 m/s. Experimental data for various magnitude of velocity demonstrate that the sensor records different thermal profiles under different fluid flow conditions. Using the transient temperature information and the inverse technique, the direction of velocity of the molten aluminum flow field can be inferred. INTRODUCTIONOur research at the University of Toronto has focused on developing invasive sensors to determine the velocity of high temperature liquid metals. High temperature in this setting is defined at VALUES (in excess of 660 °C. The discussion which will persist in this manuscript involves detecting the direction of flow in liquid aluminum using an inverse heat transfer technique. We first reported on the sensor which is used in this article in the following two publications (Sukhram and Argyropoulos, 2011a; Sukhram and Argyropoulos, 2011b). The motivation to perform this research is due to the lack of sensors available to characterize the conditions within a high temperature liquid metal reactor/vessel. A report conducted by The Minerals Metals and Materials Society (TMS Energy 2011) has suggested that the introduction of sensors into molten metal processing environments has the potential to increase process efficiency up to 15%. Such sensors will aid in the understanding of high temperature liquid metal processing operations with the goal to implement more efficient process design and practice."

Jan 1, 2012

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012

By Robert B. Parsons

"The last edition of Tax Notes expressed concern about two proposed tax changes in Finance Minister Paul Martin&apos;s 1995 budget that could have detrimental effects on Canada&apos;s mining industry. This month, Tax Notes expands on these concerns. This article is based on a paper that the author presented at ClM &apos;95 in HalifaxIntroductionOn a global basis, there are more investment opportunities in the mining industry today than at any other time in history. Countries in Central and South America, Eastern Europe, the CIS, Central Asia, and Asia are competing aggressively to attract investment to all sectors of their domestic mining industries. Today, the demand for investment dollars exceeds the amount of dollars that are available for investment in mining. It is not surprising, then, that the established mineral producing nations are witnessing a decline in spending on exploration and development on their home turf, and an increase in spending in developing countries. In the context of a developed country such as Canada, there are two manifestations of the problem of declining investment: (I) Foreign investors are allocating more of their capital budgets to new opportunities in developing countries; and (2) Canadian juniors and seniors are spending proportionately more abroad. This shift in global spending patterns is the source of some concern for the future of Canada&apos;s mining industry, particularly because it is widely believed that the current rate of discovery of ore reserves in this country is too low to replenish depleting reserves.""Government bashing"" has always been a popular pastime in Canada. Invariably, this pastime has focussed, at !east in part, on taxation. In view of the intense competition that Canada faces on the global mining scene, it is important that the role of taxation in the decision-making process be kept in perspective. This paper seeks to put the role of taxation into perspective."

Jan 1, 1995

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division&apos;s Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine&apos;s Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

By Sunil S. Gandhi

"Uranium occurrences are widely distributed in tuffaceous-argillaceous beds and abundant rhyolitic volcanic rocks of the upper Aillik group, which is more than 3 km thick and over 125 km by 40 km in areal extent. They include partially developed Kitts and Michelin deposits, containing 1560 and 7366 t U respectively.Uranium occurs mainly as disseminated fine pitchblende grains in beds and lenticular stratabound zones, and rarely as coarse pitchblende aggregates and thin veinlets. The Kitts deposit and ten other occurrences are in the argillaceous-tuffaceous beds within a steeply dipping stratigraphic zone, less than 50 m thick and over 20 km long, at the base of the upper Aillik group. The occurrences hosted by the rhyolitic rocks, numbering over fifty and including the Michelin deposit, are in elongate structural-stratigraphic belts or zones, and are characterized by a pronounced enrichment of soda and depletion of potash associated with mineralization. The mineralized zones are affected to a varying degree by Hudsonian deformation, metamorphism and granitic intrusions.The uranium mineralization is interpreted as genetically related to the felsic volcanism, involving syngenetic deposition in argillaceous-tuffaceous beds and epigenetic emplacement in rhyolites. The volcanic activity occurred 1855 ± 5 Ma ago according to a preliminary U-Pb zircon date on porphyritic rhyolite. Pitchblendesfrom the Kitts and Michelin deposits and a few other occurrences in rhyolites have yielded nearly concordant dates in 1810 to 1730 Ma range. They reflect resetting of isotopic equilibrium at the time of Hudsonian deformation. Other isotopic data on pitchblendes and galena from veins and aggregates .in the south near the 'Grenville Front' indicate local redistribution of uranium and radiogenic lead at the time of Grenville Orogeny approximately 1100 Ma ago."

Jan 1, 1986

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By K. S. Fraser, H. J. H. Pieterse

"A pressure oxidation plant to pretreat refractory sulphide ore at the Goldstrike plant in Nevada, was commissioned in early February 1990. The plant, with a nominal capacity of 1363 t/d, was commissioned over a one-week period and achieved design capacity and availability within ten weeks an unusually short period for a plant of this complexity.The pressure oxidation process is conducted under elevated temperature and pressure conditions, and in a corrosive environment. These conditions demand that the process and engineering design of the plant be carried out in a much more sophisticated and detailed manner than is normally required in a conventional gold plant.This paper provides an account of the process and engineering design of the Goldstrike pressure oxidation plant with special emphasis on the design of the vessels, slurry pumps, piping, valves, and control systems.BackgroundLocationThe Goldstrike property is located in Eureka County in northcentral Nevada on the Carlin geological trend. The mine is approximately 40 km northwest of the town of Carlin which is situated on Interstate Highway 80. The minesite is located 1700 m above sea level in the Tuscarora Mountains.Initial Goldstrike OperationsShallow, low-grade mineralization was discovered by diamond drilling in the Goldstrike area in the 1960s. A heap leach operation was established in the mid-I970s by the previous owners. The Post deposit was discovered in 1982. Gold production by mining and heap leaching reached I t/a (40 000 oz/a). American Barrick purchased the property in 1987 and started an aggressive program of deep drilling. This led to the discovery of the Betze and Deep Post deposits and established sufficient reserves to justify an initial 4100 t/d mill and a 5 500 000 t/a heap leach operation"

Jan 1, 1992

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By P. Van Marcke, X. Sillen, G. J. Chen, I. Troullinos, A. Dizier, J. Leysens, X. L. Li, J. Verstricht

"In Belgium, Boom Clay is considered as one of the potential host formations for the disposal of the High Level radioactive Waste (HLW). The URL HADES at 223 m depth at Mol site was constructed in order to study the feasibility of HLW disposal in Boom Clay. Since 1995, the URL R&D programme has focused on large scale demonstration tests like the PRACLAY experiment.The PRACLAY in-situ experiments include a set of three tests: The gallery and crossing test, PRACLAY Heater test and PRACLAY seal test. The main aim of the Heater test is to study at a large scale the thermal impact of a HLW repository on the host rock. The test is housed in the PRACLAY gallery. A hydraulic seal, made of compacted swelling and low permeable bentonite annular ring was installed at the intersection between the heated and the non-heated part of the gallery. The primary objective of the seal is to provide undrained hydraulic boundary conditions for the Heater Test.The PRACLAY gallery was constructed in 2007 and the hydraulic seal was installed in 2010. The bentonite is hydrated by natural and artificial process. The swelling, total pressure and pore pressure of the bentonite are continuously measured and analysed by numerical simulations to get a better understanding of this hydration processes. The performance of the seal is tested systematically by means of gas injection breakthrough tests and permeability tests at interface bentonite / Boom Clay and in the Boom Clay around the seal.The PRACLAY Heater will be turned on at the end of Oct. 2014, since a sufficient seal swelling has been attained to fulfill its role for the PRACLAY Heater test. This paper will focus on the PRACLAY Seal test: How we understand the process behind the hydration of the bentonite and how we test the performance of the bentonite seal."

Jan 1, 2015

By Alan Bateman

Introduction A few years ago the name Katanga recalled, to those interested in copper, a far-off country in central Africa where deposits of huge size were beginning to pour a stream of copper into the world&apos;s markets. But no one heard of the adjacent part of northern Rhodesia as a potential copper region. It was then a bush-covered wilderness, with a few lonely, widely-spaced villages, and here and there a copper prospect that created but little outside attention. There was also one struggling mine whose development created pessimism. The low-grade carbonate outcrops of Rhodesia did not compare favourably with the rich carbonate ores of Katanga. And, since Katanga was mining only oxidized ores, it was then thought that this adjacent region likewise would contain only oxidized ores. The one mine that had been started, Bwana M&apos;Kubwa, was working on low-grade carbonate ore at a loss. The outlook was not promising. But, a little over three years ago, the aspect changed. The vision of one far-sighted engineer embraced the possibility that here copper sulphides might underlie those low-grade carbonate croppings. His courageous associates furnished the capital; drilling commenced, and the great Roan Antelope mine rapidly emerged. In quick succession, the N&apos;Kana, Mufulira, N&apos;Changa, N&apos;Changa Extension, and Chambishi mines were heard from. Prospecting and development are now proceeding apace, towns are being hewn out of the virgin bush, plants are being reared, and ramifying branch railways are being pushed out from the single line of steel that now connects Rhodesia with the coasts to the south. A great new copper-mining centre is in the making, about which the world will hear much in the future. As with most new mining camps, rumors abound regarding its ore possibilities; some are correct, some are erroneous, and reliable information unfortunately is all too scanty.

Jan 1, 1930

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By Georges Croisé, Les-Lee Thompson, Adrien Debergé

Membrane filtration systems have regained focus in recent years as an effective means of liquid-liquid separation to increase the concentration of valuable elements, recover reagents or remove impurities. ORANO Mining (formerly AREVA) investigated this cost optimization process opportunity as early as 2011 for implementation at the Trekkopje project (Namibia). The key focus was to separate and recycle bicarbonate from the uranium bearing eluate solution. The performance targets were successfully achieved at lab- and pilot scale with an ultrafiltration and nano-filtration configuration system. Early 2015, ORANO Mining further launched an investigation into the use of membranes for acid recycling at the KATCO In Situ recovery mine in Kazakhstan based on the favorable results from the original bicarbonate application. KATCO is the world leader in ISR uranium mining with an eluate processing capacity of 80 000 m3/yr. This site consists of two processing plants namely, Muyumkum and Tortkuduk, located 40 kilometers apart, both operating under acidic conditions whereas precipitation and packaging are based in Tortkuduk only. This paper serves to present the results from the integration of a nano-filtration system at the Muyumkum satellite processing plant. The project consisted of screening laboratory bench studies conducted at ORANO-CIME followed by process validation at KATCO through further bench and pilot test work. The feasibility study assessments were successfully concluded which led to the implementation at an industrial scale in Muyumkum of a nano-filtration process to reduce eluate volumes being sent to the uranium precipitation section whilst achieving effective separation of uranium from sulfuric acid. Nano-filtration technology has drawn significant attention due to the efficiency and reproducibility of the process and its moderate capital cost relative to operational savings. The reliability of the previous results is a great opportunity to reduce operative expenditures within ORANO’s next ISR mining project in Mongolia.

Jan 1, 2020