Search Documents

By K. V. Phani Prabhakar, G. Padmanabham1, L. Subashini

Laser-arc Hybrid Welding (LAHW) is a relatively recent concept which effectively combines the advantages of laser welding such as the high depth of penetration, low heat input, high welding speed and the positive aspects of arc welding such as better edge bridging and possibility to add filler. For example, steel sections upto 12 mm thickness have been successfully welded in a single pass at a welding speed of 1 m/minute using a 3.5 kW CO2 laser in combination with a MIG arc. Maraging steel of grade M250 is widely used in the aerospace industry in thicknesses upto 10 mm. Conventionally, it is possible to MIG weld such thicknesses in 3-5 passes employing V-Groove joint preparation. However, this multi-pass welding results in formation of reverted austenite in the weld zone after post weld aging; and the high heat input widens the reverted austenite containing heat affected zone which is popularly known as the dark zone/eyebrow zone. Both these zones are detrimental to strength of the welded joint, specifically the fracture toughness. The width of the dark band is an important factor because, thinner the band, it is supported more effectively by the surrounding material. Therefore, in order to avoid multi-pass welding and reduce the overall heat input, single-pass laser-MIG hybrid welding was attempted on 10 mm thick maraging steel M 250 plates using a hybrid laser arc welding system comprising a 3.5 kW CO2 slab laser and a MIG welding system. Simultaneously, multi-pass MIG welds also are produced. Both the laser-MIG hybrid and MIG welds are characterized microstructurally and subjected to mechanical tests such as tensile and fracture toughness in as-welded and post weld aged condition. The amount and distribution of reverted austenite in the fusion zone and width of the dark band was found to be different. Hybrid welds showed a narrow dark band zone and improved mechanical properties. Laser-hybrid and MIG welding investigations carried out on thick section maraging steel M 250 will be presented in detail, including microstructure, tensile properties and fracture toughness of the welds. To the best of the knowledge of the authors there are no reports on laser-MIG hybrid welding of maraging steels.

Jan 1, 2014

By R. Augsten, K. K. Feng, K. C. Cheng

"Methane emission and the desorption characteristics of vertical borehole coal samples of Greenhills multiple seams in the vicinity of Elkford, British Columbia were investigated. Three vertical boreholes at depths of 335 m, 380 m and 395 m were drilled along the west wall of an active open pit mine and 44 core samples from various coal seams were obtained for desorption studies.The results are presented in three tables and illustrated with six figures. The methane content was found to increase significantly at depths greater than 200 m. The adsorption equation by Kim and the properties of the coal have been used to predict the methane content and these were compared with the measured values by the direct method.IntroductionThe coalification of plant material in the sedimentary rock produces different ranks of co al and gases of various composition. The gas mixtures are retained in coal beds and rock strata under pressure. The gas content in a coal bed varies considerably depending on the rank of coal and the depth of overburden. The gas content is defined as the volume of gases adsorbed in a unit weight of coal materials. The net amount of gases remaining in a coal seam depends on the difference in the rate of generation of methane by geo-thermal heat and the rate of diffusion of the gases out of the coal bed through sedimentary cover. The major factor that causes the change in rank and the liberation of gases is the temperature, which is governed by the thermal conductivity of sedimentary cover and the heat flux through the underlying rocks. The rate of diffusion of the gases out of the coal is governed by the porosity of the overlying rocks and the degree of fracture. The measured values of gas content in major North American coal beds are from zero up to 24 cm3 per gram of coal(1,2). A gas content of 2.5 to 9 cm3/g is considered ""gassy"" and that of 9 cm3/g or higher is considered ""very gassy"" for underground mining(3). Normally, the gas mixtures released from bituminous coal in Canada contain 90 to 98% methane and the remainder is made up of CO2, N2, 02, H2, He and other hydrocarbons(4)."

Jan 1, 1984

By S. W. Henley

"Shaft sinking design is typically driven by what has been successful in the past and the availability of sinking plant. This document considers a project where the sinking design and methodology is unconstrained by conventional thinking and removed from the commonly held belief that a sinking methodology should be developed from available winding plant. Schedule was a key driver for the Project and led to an alternative sinking design that aimed to optimise sinking advance rates by specifying new winders that compliment known sinking plant while providing improved safety, redundancy and flexibility within each part of the sinking cycle. KEYWORDS Consistent, Efficient, Flexible, Improved, Innovative, Optimise, Redundancy, Safety, Schedule INTRODUCTION The project is remotely located in the South Gobi region of Mongolia on a brownfield site and the scope of work included the concurrent blind sinking and concrete lining of two (2) ventilation shafts to an approximate depth of 1,150 m at a finished diameter of 10 m and 11 m respectively. All sinking and lining operations to be completed as in-line activities, (no lining whilst other activities are undertaken). The project was schedule driven with a completion date set for the first quarter (calendar) of 2021 and there were no restrictions imposed on the successful Contractor with respect to their equipment selection. Existing sinking plant already onsite from three previous shaft sinking operations would be made available to the Contractor if required on an as is where is basis Sustained advance rates in excess of 2.4 m per day would be required in order to achieve the completion milestone, therefore the design would have to include contingency and demanded flexibility to account for equipment down time. Previous shafts that had been sunk onsite have utilised a single double drum kibble (bucket) winder (hoist) with a single excavator loading on the shaft floor into a large capacity kibble (bucket). DESIGN Mucking The sinking design centred on the mucking cycle given that this is traditionally the most restrictive part of the sinking cycle and typically accounts for one third of the overall sinking cycle. The Vertical Shaft Mucker (VSM) and/or diesel excavator are commonly used plant for shaft sinking that were under consideration. The use of Cactus Grabs was not considered given the higher risk associated with grab ropes and hoist failures."

Jan 1, 2019

By M. H. Moys, J. A. Engelbrecht

"Large-diameter flotation columns are subject to severe axial mixing which has reduced column recovery and has generally limited it to cleaner applications. It has been assumed that columns with diameter greater than 1 m should be baffled to reduce axial mixing, but little work has been reported quantifying the effectiveness of baffling. Tests were done on a 0.2 m by 2 m column fitted with baffles of different geometry. It was generally found that the inclusion of baffles in the column worsened rather than improved mixing conditions in the column. This is explained in terms of a model for the effect of poor gas distribution on the behaviour of the column; this showed that under typical conditions a 16% excess of gas flux in the one compartment of a two-compartment column could result in one of the compartments being ""dead"" (i.e. with no net flow of slurry through it), resulting in a substantial loss of performance. The quality of mixing in the laboratory column was only reliably improved when the baffle was raised so that its top was positioned above the froth-slurry interface level. It should be possible to increase column recovery substantially with this configuration. The improved residence time distribution also means that columns can be used more effectively in roughing and scavenging applications. IntroductionFlotation columns have generally been used in cleaner applications, starting with their dramatic success at Mines Gaspe(1). Their lack of applications as roughers and scavengers is probably due to their poor residence time distribution (RID) when compared to the conventional cells they would replace. Espinosa-Gomez et al,(2) recently used them in rougher applications but installed three columns in series, presumably to cope with this disadvantage.Dobby and Finch in their seminal papersl(3,4) on the scale-up of flotation columns were the first to quantify the impact of axial mixing on the performance of industrial flotation columns. Laplante et al.(5) collected further data from the literature for column diameter D, ranging between 5 cm and 183 cm, gas superficial velocity Jg ranging between 0.7 cm/s and 2.8 cm/s and per cent solids in the feed S ranging between 3% and 52%. These data were analyzed with reference to the axial mixing model using the boundary conditions for closed vessels (the latter are more appropriate for flotation columns but the model is more difficult to use because analytical solutions for the RID are not available). The data were correlated by:"

Jan 1, 1993

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By M. J. Michaud, M. J. Lavigne

"Abstract - North American Palladium Ltd. operates its Lac des Iles open pit palladium mine 85 km north of the city of Thunder Bay, Ontario. The Roby Zone deposit occurs within the mafic/ultramafic Lac des Iles Intrusive Complex (LDI-IC), which was created by multiple pulses of magma of varying composition within several closely spaced chambers. Chaotic lithological distribution, the presence of magmatic breccias, and the rarity of rhythmic layering suggest a dynamic intrusive environment with disruptive magma pulses. As of December 31, 2001, measured and indicated resources for the 950 m long by 815 m wide Roby Zone deposit totalled 159 Mt grading 1.55 g/t Pd, 0.17 g/t Pt, 0.12 g/t Au, 0.05% Cu, and 0.05% Ni at a palladium cut-off grade of 0.7 g/t. The Roby Zone contains an additional 73 Mt of inferred resources at similar grades.The Roby Zone is dominated by varitextured gabbro containing pipes and pods of breccia, and large blocks (~60 m across) of varying lithology. Mineralization at Lac des Iles occurs as: (1) a PGEand base metal-rich magmatic matrix of breccia (breccia ore); (2) mineralized dikes or sills (gabbronorite in North Roby ore); (3) lower-grade mineralization in varitextured units that are host to the distinctive breccia ore and envelope the North Roby ore; and (4) high-grade mineralization associated with strong silicate alteration exemplified by high-grade ore.The close spatial association of the mineralized breccias with both varitextured units and silicate alteration leads to an interpretation that the energetic magma that created breccia was charged with a dissolved fluid, and that this deuteric fluid exsolved at high temperatures to migrate through crystal mush, enhancing crystallization along its pathways, resulting in variable grain size. This transformation occurred at high temperature and produced sulfide-poor, varitextured gabbro-hosted mineralization exemplified by some of the mineralization in the North Roby Zone, and also found throughout the Roby Zone. The association of hydrous silicate alteration with mineralization can be explained by continuing fluid migration during cooling and continued metal transport. Résumé - North American Palladium Ltd. opère la mine à ciel ouvert de Lac des Iles située à 85 km au nord de Thunder Bay, Ontario. Le gisement Roby Zone est encaissé dans le complexe mafique/ultramafique de Lac des Iles (LDI-IC), lequel représente une intrusion polyphasée créée par plusieurs pulses magmatiques de différente composition à l’intérieur de chambres magmatiques fermés. La distribution chaotique des lithologies, la présence de brèches magmatiques, et la quasi-absence de litage rythmique suggèrent un environnement magmatique dynamique perturbé par l’introduction de nouveau magma. Au 31 décembre 2001, les ressources mesurées et indiquées s’élevaient à 159 millions de tonnes titrant 1,55 g/t Pd, 0,17 g/t Pt, 0,12 g/t Au, 0,05% Cu, et 0,05% Ni, pour une teneur de coupure de 0,7 g/t Pd. De plus, la Roby Zone contient 73 millions de tonnes de ressources inférées à une teneur similaire.La Roby Zone est principalement encaissée dans un gabbro de texture hétérogène (varitextured) caractérisé par des cheminées et des lentilles de brèches et des énormes blocs (environ 60 m de diamètre) de plusieurs lithologies. Au Lac des Iles, la minéralisation en EGP et en métaux de base se retrouve dans la matrice magmatique de brèches (breccia ore), dans des dykes ou des sills minéralisés (gabbronorite dans la zone North Roby ore), comme minerai de basse teneur encaissant le minerai de brèche (breccia ore) et enveloppant la zone North Roby. Du minerai de haute teneur est également associé avec une forte altération en silicates dans la zone high-grade ore.L’étroite association spatiale entre les brèches minéralisées et les unités de texture variée (varitextured) et l’altération en silicate suggère que le magma énergique qui a causé la bréchification était chargé de fluides. Ces fluides deutérique"

Jan 1, 2001

By P. Lefebvre, J. Sargent, K. Major, B. Darnton

"Stillwater Mining commenced mining operations at Nye, Montana in 1987 for the recovery of platinum and palladium. Exploration identified that the J-M Reef extended for 43 km. In 1998 Stillwater Mining made the decision to develop the East Boulder mine complex, located approximately 13 miles from the Stillwater mine complex at Nye, to increase production. This paper describes the design, construction, and start-up of the East Boulder process plant.INTRODUCTIONStillwater Mining Company have been producing Platinum and Palladium from their Nye, Montana operations since 1987. The mine production from Nye had been increased in stages with mine production being delivered through several portals and one vertical shaft.The deposit is narrow veined which prevents the application of bulk mining methods and thus limits the production capabilities.In order to increase the production of platinum (Pt) and palladium (Pd) Stillwater made the decision to access the ore from the J-M Reef from the East Boulder site. The East Boulder mine site is located about 21 km (13 miles) from Nye, however as shown in Figure 1, the travel distance is closer to 188 km (114 miles). Distance, on strike, and space availability at Nye precluded the expansion of the Nye concentrator to handle the increased mining rate and supported the decision to install a new concentrator at East Boulder."

Jan 1, 2003

By Lewis Martin

Whereas many researchers and mine engineers have conducted tests using different types of grout, grout ratios, and physical modifications of the cable to determine cable bolt load characteristics, few studies have been conducted on cables fitted with internal instruments. Those studies that have been done have concentrated on cable behavior averaged over significant cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed . This paper documents test results on these modified cable bolts. Three tests were conducted at SRL on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over significant cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable and thereby allow interpolation of maximum possible loads on a cable.

May 1, 2002

By J. A. Finch, A. R. Laplante, R. Espinosa-Gomez

"The Niobec concentrator rejects up to /5% of the Nb as slimes (-10u.m). The recovery of Nb from these slimes by column flotation is being studied. An essential condition for selective flotation is slimes dispersion. A particle size analyzer, the Sedigraph 5000D, was used to monitor dispersion in plant waters with combinations of organic and inorganic dispersants and flotation reagents. Flotation reagents were particularly detrimental to dispersion with sodium silicate. The best dispersion conditions were selected for column flotation tests. These tests revealed that reagent combination had a pronounced effect on froth stability. Careful frother selection achieved good froth stability under conditions of good dispersion. Plant water increased the required dispersant concentration causing mineral depression.IntroductionSlimes (-10 u.m) rejected at Niobec contain up to 15070 of the over-all Nb content . Recovery of Nb from these slimes would significantly increase over-all recovery. A suggested recovery route involves two phases: (1) carbonate flotation (to remove most of the carbonates) depressing silicates and pyrochlore (as currently done at Niobec); and (2) selective (direct) pyrochlore flotation from the silicates. Phase 2 has been addressed and several routes to achieve selective flotation are available. Phase I was attempted with the selective reagent scheme used at Niobec but a considerable amount of pyrochlore floated with the carbonates due to poor slimes dispersion."

Jan 1, 1987

By H. J. Conolly

The area around Osisko lake, the Horne mine, and the town of Rouyn, in northwestern Quebec, presents a most interesting structural problem. The present discussion is confined to an area around Osisko lake, about six miles long and three miles wide, shown in Figure 1. The writers are particularly indebted to Mr. Thayer Lindsley, of Ventures Limited, who sponsored the investigation and gave permission to publish this paper. Mr. H. L. Roscoe and Mr. Oliver Hall, of Noranda Mines, Limited, gave every possible assistance; and the Noranda geologists, Mr. H. M. Butterfield, Dr. Peter Priee, and Dr. G. G. Suffel, contributed many data and ideas. It is a pleasure to acknowledge also the fuidance of Dr. W. F. James and Dr. B. S. Buffam and the full use made o their maps and criticism. Dr. M. E. Wilson and Dr. A. Lang, of the Geological Survey of Canada, kindly furnished data on the geology in neighbouring fields. Mr. E. Bailey assisted ably in the field, and Mr. H. F. King kindly reviewed the text. Memoir 166 of the Geological Survey of Canada, The Geology and Ore Deposits of the Roztyn-Harricanaw Region, Quebec, by Cooke, James, and Mawdsley, proved an invaluable source of information. STRATIGRAPHY The following stratigraphie sequence is based in part upon the interpretation of the structure as outlined in this paper:

Jan 1, 1936

By Nathalie Gauthier

Bien que le système de ventilation du Puits Penna soit de taille imposante et que plus de $30M y seront engloutis pour son développement, aucun budget spécifique n?avait été préalablement consenti pour refroidir l?air acheminé aux places de travail dans la partie profonde de la mine. Le système de ventilation a été conçu en deux étapes distinctes : le réseau du haut de la mine lequel dessert jusqu?à 1550 m de profondeur et le réseau du bas de la mine (de 1550 m à 2200m) qui a été créé ultérieurement. Le réseau inférieur a été imaginé de façon à acheminer l?air frais directement au gisement et de permettre l?évacuation aux extrémités afin de rejeter l?air chaud immédiatement après l?avoir utilisé. Au total, lorsque le réseau de ventilation sera complété, plus de 670 m3/s d?air sera véhiculé dont jusqu?à 495 m3/s pour la partie inférieure de la mine considérant une capacité totale maximum de 710 m3/s en utilisant la mine adjacente.

May 1, 2003

By S. Amira

The corrosion behavior of high pressure die-cast and thixocast AXJ530 magnesium alloys has been investigated in 0.05M NaC1 solution at pH 6.0 using potentiodynamic polarization tests, electrochemical noise (EN) technique, electro-chemical impedance spectroscopy (EIS) and scanning reference electrode technique (SRET). The behavior of die-cast and thixocast specimens were compared using each of these techniques and the results discussed. Further tests have been carried out with die-cast AZ91D alloy to better compare and interpret the results. Experiments indicate that the thixocast specimens of AXJ530 alloy have a better corrosion resistance than those of die cast alloy in neutral solution.

Jan 1, 2006

By Christopher Boys

"Abstract -Many water inflows in Saskatchewan potash mines are linked to salt anomalies. Potash ore and three anomalies in the PCS Cory potash mine in the Patience Lake Member of the Prairie Evaporite Formation were studied to understand the processes involved in their formation. Another goal was to find geological indicators of the proximity of anomalies. A geological model that relates the potash to the salt anomalies has been developed.Up to five post-burial facies may be recognized . These range from carbonate-mud collapse breccias to bedded sylvinite, and probably result from post-burial leaching. ln this model, the same fluids that caused widespread recrystallization and possibly enrichment of the potash salts, started by dis­ solving huge cavities in the evaporites . The effects of the leaching were highly variable, indicated by selectively preserved delicate laminae and chevron textures, to deformed and totally dissolved salt beds . ln at least two major events, Late Devonian and Cretaceous, collapse structures may have acted as conduits for overlying formation waters to cause pervasive leaching and recrystallization of the Prairie Evaporite Formation .Geological indicators of the proximity of an anomaly may include: a change in Insoluble seam color from greenish-gray to mottled brown and greenish-gray, unusual local increases in ore grade, large patches (e.g., >200 cm2) of sylvite-poor potash crosscutting units near the top of the ore zone, and drops in topography >10 m of the marker seams. Anhydrite was more common in an anomaly than in ore. The local abundance of anhydrite in ore may indicate the proximity of some salt anomalies.Once an anomaly has been encountered, indicators of a major collapse feature may include: stretched clay seams, folded beds, small collapse features (1 m to 20 m), numerous washouts, or split clay seams with injected salt. Any number, or none, of these indicators may be found close to a major collapse feature."

Jan 1, 1993

By M. Choy, A. Kadiayi, E. Magdzinski

"Design of engineering controls to limit occupational noise exposure rely on accurate calculation inputs. Sound in mines can carry considerable distances. Mine ventilation engineers rely on noise propagation calculations to estimate silencer performance criteria for key mine fan installations that are often in proximity to occupied areas of a mine and can remain in service for decades. The blasted and rockbolted walls of hard rock mining tunnels have unique acoustical properties. Underground testing in an operating metal mine in Sudbury, Canada was performed and results processed to characterize noise propagation in mines, with the goal of improving the accuracy of noise calculations.INTRODUCTIONAs mine operators continue to improve and promote workplace safety, addressing noise at fixed infrastructure locations is observed as increasingly common. Underground fans are important to consider in this context, as they are typically loud, in proximity to occupied and sensitive workplaces, and operate nearly continuously. Predicting noise propagation from ventilation fans within underground mines has long been a challenge, with few available resources documenting acoustical properties as calculation inputs. Other factors in addition to rock face absorption properties include tunnel geometry and distance from the fan, which play critical roles in characterizing the noise level at any given point away from the fan. By understanding and establishing methods to better predict noise dissipation along underground mining tunnels, engineers can design noise controls with a greater degree of precision and confidence to effectively protect workers from over exposure to noise.This paper investigates classical methods of predicting reverberant room and direct field noise propagation. These prediction methods are then compared to noise measurements taken within the Fraser Mine of Glencore’s Sudbury Integrated Nickel Operations (Sudbury INO) Measurements were taken at a depth of ~881 m (2,889 ft), along an ~300 m (984 ft) long blasted hard rock mining tunnel. The noise along the mine tunnel resulted from the intakes of two 900 kW (1,200 hp) ventilation fans with a combined exhaust capacity of 300 m3/s (630,000 cfm)."

Jan 1, 2019

By E. A. Davies, Trevor T. Jones

"Aspects of materials, design and operation of suspension equipment is dealt with, hazard, fatigue and special metallurgical properties of certain steels to resist are described, as is the effect of temperature in service modifying the properties of some steels to resist stress concentration and propagation of cracks.The influence of steady impact and fatigue loading and its results are described. Control of manufacture including nondestructive testing is outlined and acceptance parameters and strength calculations are given. Quality requirements and control in manufacture are outlined. A short description of the overwind detaching hook, together with illustrations of the operation of detachment are presented.MaterialsWinding engine ratings of 8000 h .p. and large capacity shafts 2000 m in depth (4000 m depths have already been reached and it may be necessary to go to 6000 m) and up to ten conveyances are not uncommon today. Loads of 100 or even 200 tons hoisted at low speeds are possible within the near future. Some of these appliances are designed to protect lives and installations in hazardous conditions when, due to human or mechanical fault, a malfunction occurs in the system. In addition, such equipment includes suspension gear of various kinds designed to anchor and apply high mechanical tensions to numerous steel ropes installed in shafts necessary either for the safe passage of conveyances or for balancing purposes when heavy loads are in motion.No unique metallurgical problems are presented in underground mining operations, but they have two special characteristics that influence the metallurgical aspects of the de sign of suspension gear and other equipment concerned in the transport of men and materials. (1) Any uncontrolled release of energy caused by the unexpected failure of a component is more likely to injure personnel and cause costly damage to installations in the narrow confines of an underground mine shaft. (2) Some mechanical equipment in mines, tends to be overloaded in service and suffer plastic distortion."

Jan 1, 1987

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By D. J. Bowen

"Abstract -The Great Dyke extends for 540 km along strike, to unknown depth, and varies in width from 3 km to 11 km. Rb/Sr age determinations gives values of approximately 2470 Ma.The Dyke consists of a variety of mafic and ultramafic rocks, many altered to serpentinites. These include, from top to bottom, successions of gabbro/norites, pyroxenites, peridotites/harzburgites, and dunites/picrites.The layers dip in from either margin, steepest at the edges (20°) and flattening toward the central sections. Four separate complexes are present. From north to south these are termed the Musengezi, Hartley, Selukwe and Wedza Complexes, and are described as 'boat-shaped' or 'pig-troughed'. All are similar in petrological sequences. Physiographically, the Dyke is spectacular in the north, where as a mountain range it meets the Zambezi Escarpment. Elsewhere in the central parts there is little surface expression and wide open treeless vleis. Dyke rocks cut through granite and schist belt terrain and are termed 'The Magnesia Belt'.Vast mineral resources exist. These include chrome, asbestos, platinoids, nickel, copper and gold. Up to eleven chrome seams numbered from top to bottom occur in the lower ultramafic sequences. Seams are narrow at 10 cm to 30 cm but of high grade. The platinum occurs 10 m to 40 m below the norite/pyroxenite contact.A 60 m wide zone of Light Sulfide Mineralization (LSM) of Jess than 1% sulfides extends from the lower gabbronorites into the upper pyroxenites. In this LSM, four enriched zones carry up to 5% sulfides. The most widespread is termed the Main Sulfide Zone (MSZ), below which is No. 2, No. 3 and No. 4 Sulfide Zones. The MSZ carrying pyrite, pyrrhotite and chalcopyrite is a multi­ element ore with components of PGE (Pt-Pd-Rh), nickel, copper and cobalt, and gold and silver.Extensive exploration programs have been carried out and the intention is to begin large-scale mining. However, with Russia supplying metals to the western markets, South Africa's cutback on production, and an end to the Cold War, delays have arisen."

Jan 1, 1994

By W. D. Sinclair, R. J. Cathro, E. M. Jensen

"The Cash is one of the largest porphyry copper-molybdenum Deposits found in Yukon to date. It is 80 km northwest of Carmacks, within the unglaciated portion of the Dawson Range, and is associated with the Big Creek fault, an important tectonic feature. Part of the mineralized zone is blanketed by up to 70 m of alluvial drift . The remainder is covered by a relatively thin residual soil layer. The mineralized zone, however, was not detected by conventional stream-sediment sampling because pathfinder elements, such as Cu and Mo, have not been geochemically dispersed into the main drainage system. The deposit was discovered by a combination of soil analysis and inspection of rock fragments from small pits.Twenty widely spaced, shallow drill holes have outlined an areaover 2700 m long and 550 to over 1000m wide that grades more than 0.1% copper equivalent (% CuE = % Cu + (5 x % MoS2)). Two smaller zones grading over 0.4% copper equivalent occur within the larger area. The limits of the widest end of the deposit have not been delineated.The Cash deposit is fairly typical of high-level, calc-alkaline porphyry copper-molydenum occurrrences in the Canadian Cordillera {cf, CIM Special Volume 15) and is representative of most prospects in the Dawson Range. It is associated genetically with a subvolcanic complex of small, irregular stocks and dykes of feldspar porphyry and related breccias of Late Cretaceous age. Copper and molybdenum sulphides occur along fractures, in quartz veinlets and disseminated in feldspar porphyry and in older metasedimentary and intrusive rocks. Higher-grade zones of copper and molybdenum have associated potassic alteration. Phyllic alteration is, in part, superimposed on potassic alteration. Argillic alteration occurs locally.This paper describes the history of the discovery and the geochemical and geophysical characteristics, together .with the regional geology, and the nature and distribution of the host rocks, hypogene mineralization and hydrothermal alteration."

Jan 1, 1981

By D. Atkinson

"Porphyry molybdenum-tungsten mineralization on the east flank of Hudson Bay Mountain crops out over 5 km2 and is intersected to depths of 2 km. Features such as a hornblende-biotite aureole, mineralogical zoning and dike, vein and fracture geometries within lithologies of the Middle to Lower Jurassic Hazelton Group and Cretaceous Skeena Group reflect an intrusive complex, the Upper Cretaceous to Early Tertiary Hudson Bay Mountain stock which has been intersected by drill holes. The stock is believed to be the mineralizing agent. A southeast-dipping granodiorite sill has been outlined by drilling within the Hazelton Group. Molybdenite and scheelite veins cut all rock types; however, the granodiorite sill hosts a higher density of fine-grained, banded, quartz-molybdenite and pegmatitic quartz-molybdenite veins reflecting a competency contrast between the intrusive sill and other country rock. Due to the relative abundance of these veins, grade is higher within areas of the sill. Above the 15000£ cross-cut 20.6 million tonnes grading 0.401% MoS2 and 0.041% W03 have been defined. During exploration of the deposit sampling procedures had to be adjusted because of the nugget effect attributed to drill intersections of banded and pegmatitic veins.IntroductionMolybdenite was discovered in outcrop at the foot of Kathlyn Glacier on Hudson Bay Mountain and first reported by the Geological Survey of Canada in 1944. The deposit has several names: Hudson Bay Mountain or Glacier Gulch, both after its location, and Yorke-Hardy after the original staker.The deposit is on the east flank of Hudson Bay Mountain, 9 km northwest of Smithers, west-central British Columbia, within NTS area 93L/14 (54° 49' North, 127° 18' West, Fig. 1). Hudson Bay Mountain, on the southern edge of the Bulkley Valley, is a dominant topographical feature reaching 2590 m elevation. Mineralization is partly overlain by the Kathyln Glacier which is visible from Highway 16. Access to the 3100 m of underground development is from a portal at 1066 m elevation on the east slope of Hudson Bay Mountain."

Jan 1, 1995

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993