Search Documents

By R. M. Porter

PILLAR extraction at the Sullivan Mine bas been in progress for over twenty-five years and bas .involved progressively larger pillars. The largest pillar blasted to date exceeds one million tons and is described in this paper. This blast is believed to be one of the largest to take place entirely under-ground. The Sullivan Mine, owned by The Consolidated Mining and Smelting Company of Canada Limited, is located in the southeastern corner of British Columbia on the east flank of the Purcell range overlooking the twenty-mile wide Rocky Mountain Trench (Figure 1). The orebody is a bedded replacement deposit in argillites, varying in thickness up to 300 feet, but averaging about 80 feet. Above the 3900 Level, the dip varies from nearly horizontal to 40 degrees; be-low the 3900 Level it varies from 45 to 20 degrees (Figure 2). Pillar extraction follows a plan of retreating outward from caved areas. The size of each blast is determined by the effect which the removal of support

Jan 1, 1961

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco's Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970

By Robert J. Uffen

YOU will likely recall the accomplishments of the International Geophysical Year of 1957, with its polar expeditions, the discovery of the Van Allen radiation belts and the spectacular launchings of the first artificial earth satellites. Our know ledge of the exterior of the earth was greatly increased by this international, friendly, cooperative scientific investigation. The Inter-national Union of Geodesy and Geo-physics has now been joined by the new International Union of Geological Sciences in sponsoring a similar study of the earth's interior. The program will extend from January, 1962 until December. 1964, and is known as the International Upper Mantle Project. During the T.G.Y studies of the interior of the earth were relatively neglected, even though the same international •Cooperation in obtaining simultaneous world-wide observations, by similar instruments, is required to locate and study earth-quakes, for example, as it is to study the earth's upper atmosphere. The upper mantle is 1•emote from man, as it extends from a depth of about 10 km. to perhaps 1000 km., but its practical importance is great.

Jan 1, 1962

By C. J. Preston, R. E. Ström, G. R. Baiden

"On January 1st 1996 Inco Limited, Tamrock OY, Dyno Explosives Group and CANMET formed a consortium for the development of robotic mining equipment. This project is a five year research and development agreement that combines the talents of the above organizations to facilitate the creation of mining equipment and systems for robotic mining.The projects are based on the communication system developed by Inco Mines Research and currently sold and marketed by Automated Mining Systems Limited. Main projects include the development and implementation of a positioning and navigation module (including a software mapping system that will be inherent to each piece of equipment), robotic systems for development and mining, and software systems to support the use of this equipment. Included in the program is the establishment of a test mine, at Inco’s 175 ore- body at Copper Cliff. This facility will allow collaboration of companies and research organizations for the design and testing of techniques and equipment for Robotic mining.This paper discusses the creation of this new research alliance, the Mining Automation Program or MAP."

Jan 1, 1997

By T. A. Lazier, C. S. Longley

"Paymaster Consolidated Mines, Limited, owns several groups of claims in various parts of the Porcupine district. The area in which mining has been carried on includes parts of lots 5, 6, and 7, con. 1, Tisdale township, and twelve adjoining claims in Deloro township to the south. Highway No. 67A between South Porcupine and Timmins crosses the property.The discovery of the Dome mine in 1909 caused a rush of prospectors to the district and in a few weeks practically all territory adjacent to the Dome was staked. At that time work was started on the West Dome, West Dome Lake, Apex, and Standard properties. These were consolidated in 1930 to form the present Company. Gold was produced from the West Dome Lake from 1915 to 1930, and from the Standard-Paymaster from 1922 to 1928. The total production of the previous and present companies from 1915 to November 30, 1946, has been 487,170 oz. gold and 149,342 oz. silver from 2,337,554 tons of ore."

Jan 1, 1954

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By J M. Anderson

The cable belt conveyor installation at Craigmont Mines Limited, Merritt, B.C., has the greatest one-stage vertical fall of any conveyor installed overland in Canada. Since the late summer of 1961, this conveyor has carried more than 5,000,000 tons of copper ore from open pit to concentrator site. When the conveyor is loaded, the drive motor acts as an induction generator, delivering power to an external circuit. This paper covers the selection, the operation, the performance statistics, and the installation and operating costs of this conveyor system. Introduction T HE Craigmont mine is located in the south-western interior region of the Province of British Columbia, approximately 240 miles northeast of Vancouver. A moderate climate, good roads, service by the Canadian Pacific Railroad, power from the British Columbia Hydro Authority, gas from the nearby main line of the Inland Natural Gas Company and close proximity to the village of Merritt provide a favourable location for this mining operation. The ore occurrences at Craigmont have a vertical extent of 1,500 feet,

Jan 1, 1965

By H. J. White

Haynes International, a world leader in the manufacture and production of nickel, and cobalt base alloys has invented and developed a low cost high temperature material, with a unique combination of superior oxidation resistance and weldability/ fabricability. HAYNES® HR-224TM (Ni ? 27.5Fe ? 20Cr ?3.8A1 ? 0.3Si ? 0.3Ti) forms a planar/ continuous/ adherent aluminum oxide film at high temperatures which has been shown to effectively limit chromium poisoning in solid oxide fuel, cell, systems. A 20,000 pound vacuum induction melted (VIM) + electroslag remelted (ESR) heat has been melted and converted into various product forms: sheet, plate, bar, welded tubing, wire, etc. The alloy was designed for service in severely oxidizing environments recuperators, automotive catalytic converters, wire strand annealing furnace tubes, etc. and has been of great interest to solid oxide fuel, cell, manufacturers as a materials of construction in balance of plant (BOP) design. This manuscript presents the physical, properties, mechanica, properties, and oxidation resistance of the alloy compared to other materials being considered for solid oxide fuel, cell, design

Jan 1, 2010

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By M. A. Hardie

"CASES and mixtures of them are so common and so much a part of everyday existence that they become so taken for granted that their individual characteristics and idiosyncrasies rarely become of curiosity to others than those involved in tl1eir production, processing, treatment, transportation, and for utilization. The use of the most common and universal mixture of gases -air -is begun at birth by ail living creatures and their discontinuation of its use terminates existence. Modern man rides on air in his tires, rides through it for high-speed transportation, and uses it for his comfort in the heating and air conditioning of his domicile. It is neither the aim nor the in-tent, in the next few moments, to provide a panacea for even a portion of the problems inherent in the gas industry nor to delve deeply into any particular facet of its diversities. The purpose is primarily to touch upon some of the peculiarities and generally to consider approaches to employ in the pursuit of solutions."

Jan 1, 1959

By J. H. C. Scrimgeour, T. Toong, R. E. Hamilton

"The principles involved in the use and application of mathematical models as an aid to the development of advanced process control computer systems are described briefly. This is followed by a brief survey of known models of this kind for the simulation of mining industry processes.The main part of the paper describes a dynamic model of the flotation process developed by Canadian General Electric. Using flotation rate constants for each species of mineral and gangue, the model provides a numerical solution of the differential equations describing cell behaviour. The cell mode] is used repeatedly as a subroutine in the •over-all-plant model. The features of the cell and plant models are described.Simulation runs from the plant model show stream .assays and other indications of plant behaviour printed typically in 1-to 10-minute steps for several hours of •Operation following typical disturbances such as changes in feed rate or reagent addition rate. The simulation can :Show expected behaviour for both uncontrolled and computer-controlled plants."

Jan 1, 1970

By J. B. Mawdsley

Introduction The writer was instructed to visit the Chibougamau region during the field season of 1927 and report on the mineral discoveries that had been made there since 1911. lt was deemed advisable to obtain detailed information regarding the rocks underlying the area in the vicinity of these recent discoveries. Accordingly an area 60 square miles in extent was mapped. The outcrops were studied along the water courses and along bush traverses spaced at half-mile intervals between these water courses. The completion of the rest of the summer's programme allowed only three weeks for this work. lt is from this small, mapped area, and this necessarily cursory survey, that the material for this paper was obtained. Location And Means Of Access The name Chibougamau district is applied loosely to an ill-defined area of about 1,000 square miles lying mostly north and west of Chibougamau lake in the Province of Quebec. The lake is approximately half way between lake St. John and James bay. It lies 150 miles north of the Canadian National railway and 40 miles south of Mistassini?lake.

Jan 1, 1928

By Dallas W. Davis

Twin - Kennecott Deal Announced April 15, 2004 ! Kennecott earns 56% interest, if in 4 years, spends C$10 million and recovers at least 200 cts of +1 mm diamonds in all dimensions from any contiguous body ! Earn-in can take up to 6 years, but incurs stepped reduction of interest from 56% to 46% or 0% if $C10 and 200 carats not achieved ! By funding all costs through feasibility study, Kennecott earns 71% in 7 years, or, stepped reduction to 62% if completed after 8 years ! By achieving production within 10 years and funding Twin?s share of development and construction costs, Kennecott earns further 4% ! If no election to develop a mine within 2 years of feasibility study completion, Twin may present development proposal which Kennecott has 60 days to elect to follow or transfer management to Twin and dilute to 49% ! Each party has one time right to elect to market its diamond share ! On signing and annually, Kennecott will purchase $C250,000 of Twin shares at 130% of then prevailing market price until achieved earn-in

May 1, 2004

By B P. Scott

Podsol soil horizons developed on Pleistocene glacial sediments overlying the Coronation Mine orebody were analyzed for copper and zinc spectro-photometrically, using biquinoline-isoamyl alcohol and dithizone carbon tetrachloride reagents. Copper and zinc are concentrated in the A. and C horizons, whereas the A1, A2 and B horizons are leached. Of economic significance is the fact that the C horizon contains a copper anomaly, in excess of 100 times back-ground, directly over the orebody. Due to the erratic distribution of high copper concentrations in the Ao horizon with respect to the orebody, that horizon is not considered as a reliable prospecting datum. U NDER certain conditions, metallic ore deposits are accompanied by primary halos of trace elements in unweathered rock surrounding the orebodies or by secondary halos in weathered rock, alluvium, soil, or vegetation above or near the mineralized zones. Where such halos occur, chemical analysis, as applied to the detection of trace elements, is a valuable prospecting aid, permitting the detection of mineralization of possible economic value.

Jan 1, 1965